Pioneer AVIC-90DVD, AVIC-88DVD, CNDV-50MT, CNDV-50MTP, AVIC-9DVD User Manual 2

...
0 (0)

Operation Manual

ENGLISH

DVD Map - USA / Canada

CNDV-50MT

CNDV-50MTP

This operation manual can be used with the following models: AVIC-880DVD, AVIC-88DVD, AVIC-80DVD, AVIC-90DVD, AVIC-9DVD

READ ME FIRST!

To Users Updating the Application Program

You need an AV Head Unit or Display with touch panel capability to use this software.

Make sure to use a display suitable for this system.

Please read the cautions on the next page before using the CNDV-50MT [CNDV50MTP] disc as there is a possible risk that the stored user-registered data may lost upon completion of the update. Please be aware that the manufacturer cannot take any responsibility for lost data in the event the data is lost.

Upgrading to the newer version page 57

Notice to all users:

This software requires that the navigation unit be properly connected to your vehicle’s parking brake. If not properly connected and depending on your vehicle, additional installation may be required. For more information, please contact your Authorized Pioneer Electronics retailer or call us at (800)421-1404.

Cautions on Updating the Application Program of the Navigation System:

Stop the vehicle in a safe location. While the program update is in progress, ensure that the power supply of the Navigation System is not turned off.

When the update procedure is complete, the Navigation System will be restarted. After the system has started up again, make sure not to turn off the power supply for the Navigation System until the map of your surroundings appears.

During the update process, there is the possible risk of the “Address Book”(*) data and the “Destination History” data being lost. It is highly recommended to use a PC Card (PCMCIA TYPE II <5 V>) to back up Address Book data. (Since the “Destination History” cannot be stored on a PC Card directly, to keep the “Destination History” data, first store it in the Address Book, then onto the PC Card.)

*“Address Book” data includes “Return Home” and “Go to” contents.

Any existing calculated routes will be canceled.

Personalized settings will return to their factory settings.

Application Program Update Procedure

Refer to the update procedure in the “Installing the Program” section (P.57) of this manual.

The screen shown in the example may differ from the actual screen.

The actual screen may be changed without notice for performance and function improvements.

Introduction

License Agreement

PIONEER CNDV-50MT [CNDV50MTP] - for U.S.A.

THIS IS A LEGAL AGREEMENT BETWEEN YOU, AS THE END USER, AND PIONEER ELECTRONICS (USA) INC. (“PIONEER”). PLEASE READ THE TERMS AND CONDITIONS OF THIS AGREEMENT CAREFULLY BEFORE USING THE SOFTWARE INSTALLED ON THE PIONEER PRODUCTS. BY USING THE SOFTWARE INSTALLED ON THE PIONEER PRODUCTS, YOU AGREE TO BE BOUND BY THE TERMS OF THIS AGREEMENT. THE SOFTWARE INCLUDES A DATABASE LICENSED BY THIRD PARTY SUPPLIER(S) (“SUPPLIERS”), AND YOUR USE OF THE DATABASE IS COVERED BY THE SUPPLIERS’ SEPARATE TERMS, WHICH ARE ATTACHED TO THIS AGREEMENT (Refer to page 5). IF YOU DO NOT AGREE WITH ALL OF THESE TERMS, PLEASE RETURN THE PIONEER PRODUCTS (INCLUDING THE SOFTWARE, AND ANY WRITTEN MATERIALS) WITHIN FIVE (5) DAYS OF RECEIPT OF THE PRODUCTS, TO THE AUTHORIZED PIONEER DEALER FROM WHICH YOU PURCHASED THEM. USE OF THE SOFTWARE SHALL BE DEEMED TO BE YOUR CONSENT TO THE LICENSE AGREEMENT.

1. GRANT OF LICENSE

Pioneer grants to you a non-transferable, non exclusive license to use the software installed on the Pioneer products (the “Software”) and the related documentation solely for your own personal use or for internal use by your business, only on such Pioneer products.

You shall not copy, reverse engineer, translate, port, modify or make derivative works of the Software. You shall not loan, rent, disclose, publish, sell, assign, lease, sublicense, market or otherwise transfer the Software or use it in any manner not expressly authorized by this agreement. You shall not derive or attempt to derive the source code or structure of all or any portion of the Software by reverse engineering, disassem-

bly, decompilation, or any other means. You shall not use the Software to operate a service bureau or for any other use involving the processing of data for other persons or entities.

Pioneer and its licensor(s) shall retain all copyright, trade secret, patent and other proprietary ownership rights in the Software. The Software is copyrighted and may not be copied, even if modified or merged with other products. You shall not alter or remove any copyright notice or proprietary legend contained in or on the Software. You may transfer all of your license rights in the Software, the related documentation and a copy of this License Agreement to another party, provided that the party reads and agrees to accept the terms and conditions of this License Agreement.

2. DISCLAIMER OF WARRANTY

The Software and related documentation are provided to you “AS IS”. PIONEER AND ITS LICENSOR(S) (for the purpose of provisions 2 and 3, Pioneer and its licensor(s) shall be collectively referred to as “Pioneer”) MAKES AND YOU RECEIVE NO WARRANTY FOR THE SOFTWARE, WHETHER EXPRESS OR IMPLIED, AND ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE FOR THE SOFTWARE ARE EXPRESSLY EXCLUDED. SOME STATES DO NOT ALLOW EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. The Software is complex and may contain some nonconformities, defects or errors. For example, the voice recognition function as implemented by the Software may not recognize your voice. Pioneer does not warrant that the Software will meet your needs or expectations, that operation of the Software will be error free or uninterrupted, or that all non-con- formities can or will be corrected. Furthermore, Pioneer does not make any representations or warranties regarding the use or results of the use of the Software in terms of its accuracy, reliability or otherwise.

1

3. LIMITATION OF LIABILITY

IN NO EVENT SHALL PIONEER BE LIABLE FOR ANY DAMAGES, CLAIM OR LOSS INCURRED BY YOU (INCLUDING, WITHOUT LIMITATION, COMPENSATORY, INCIDENTAL, INDIRECT, SPECIAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES, LOST PROFITS, LOST INCOME, LOST SALES OR BUSINESS, EXPENDITURES, INVESTMENTS, OR COMMITMENTS IN CONNECTION WITH ANY BUSINESS, LOSS OF ANY GOODWILL, OR DAMAGES) RESULTING FROM THE USE OF OR INABILITY TO USE THE SOFTWARE, EVEN IF PIONEER HAS BEEN INFORMED OF, KNEW OF, OR SHOULD HAVE KNOWN OF THE LIKELIHOOD OF SUCH DAMAGES. THIS LIMITATION APPLIES TO ANY AND ALL CAUSES OF ACTION INDIVIDUALLY OR IN THE AGGREGATE, INCLUDING WITHOUT LIMITATION BREACH OF CONTRACT, BREACH OF WARRANTY, NEGLIGENCE, STRICT LIABILITY, MISREPRESENTATION, AND OTHER TORTS. IF PIONEER’S WARRANTY DISCLAIMER OR LIMITATION OF LIABILITY SET FORTH IN THIS AGREEMENT SHALL OR FOR ANY REASON WHATSOEVER BE HELD UNENFORCEABLE OR INAPPLICABLE, YOU AGREE THAT PIONEER’S LIABILITY SHALL NOT EXCEED FIFTY PERCENT (50%) OF THE PRICE PAID BY YOU FOR THE ENCLOSED PIONEER PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty disclaimer and limitation of liability shall not be applicable to the extent that they are prohibited by any applicable federal, state or local law which provides that such a disclaimer or limitation cannot be waived or preempted.

4. EXPORT LAW ASSURANCES

You agree and certify that neither the Software nor any other technical data received from Pioneer, nor the direct product thereof, will be exported outside the United States except as authorized and as permitted by the laws and regulations of the United States. If the Software has been rightfully obtained by you outside of the United States, you agree that you will not reexport the Software nor any other technical data received from Pioneer, nor the direct product thereof, except as permitted by the laws and regulations of the United States and the laws and regulations of the jurisdiction in which you obtained the Software.

5. TERMINATION

This Agreement is effective until terminated. You may terminate it at any time by destroying the Software. The Agreement also will terminate if you do not comply with any terms or conditions of this Agreement. Upon such termination, you agree to destroy the Software.

6. U.S. GOVERNMENT END USERS

If the Software is being acquired by or on behalf of the United States government or any other entity seeking or applying rights similar to those customarily claimed by the United States government, the Data is licensed with “Limited Rights.” Utilization of the Software is subject to the restrictions specified in the “Rights in Technical Data” clause at DFARS 252.227-7013, or the equivalent clause for non-defense agencies. Pioneer Electronics (USA) Inc., 2265 East220th Street, Long Beach, CA 90810.

7. MISCELLANEOUS

This is the entire Agreement between Pioneer and you regarding its subject matter. No change in this Agreement shall be effective unless agreed to in writing by Pioneer. Pioneer retailers do not have the authority to change this Agreement. This Agreement shall be governed by and construed in accordance with the internal laws of the State of California. If any provision of this Agreement is declared invalid or unenforceable, the remaining provisions of this Agreement shall remain in full force and effect.

2

PIONEER CNDV-50MT [CNDV50MTP] - for Canada

THIS IS A LEGAL AGREEMENT BETWEEN YOU, AS THE END USER, AND PIONEER ELECTRONICS OF CANADA, INC. (“PIONEER”). PLEASE READ THE TERMS AND CONDITIONS OF THIS AGREEMENT CAREFULLY BEFORE USING THE SOFTWARE INSTALLED ON THE PIONEER PRODUCTS. BY USING THE SOFTWARE INSTALLED ON THE PIONEER PRODUCTS, YOU AGREE TO BE BOUND BY THE TERMS OF THIS AGREEMENT. THE SOFTWARE INCLUDES A DATABASE LICENSED BY THIRD PARTY SUPPLIER(S) (“SUPPLIERS”), AND YOUR USE OF THE DATABASE IS COVERED BY THE SUPPLIERS’ SEPARATE TERMS, WHICH ARE ATTACHED TO THIS AGREEMENT (Refer to page 5). IF YOU DO NOT AGREE WITH ALL OF THESE TERMS, PLEASE RETURN THE PIONEER PRODUCTS (INCLUDING THE SOFTWARE, AND ANY WRITTEN MATERIALS) WITHIN FIVE (5) DAYS OF RECEIPT OF THE PRODUCTS, TO THE AUTHORIZED PIONEER DEALER FROM WHICH YOU PURCHASED THEM. USE OF THE SOFTWARE SHALL BE DEEMED TO BE YOUR CONSENT TO THE LICENSE AGREEMENT.

1. GRANT OF LICENSE

Pioneer grants to you a non-transferable, nonexclusive license to use the software installed on the Pioneer products (the “Software”) and the related documentation solely for your own personal use or for internal use by your business, only on such Pioneer products.

You shall not copy, reverse engineer, translate, port, modify or make derivative works of the Software. You shall not loan, rent, disclose, publish, sell, assign, lease, sublicense, market or otherwise transfer the Software or use it in any manner not expressly authorized by this agreement. You shall not derive, or attempt to derive, the source code or structure of all or any portion of the Software by reverse engineering, disassembly, decompilation, or any other means. You shall not use the Software to operate a service bureau or for any other use involving the processing of data for other persons or entities.

Pioneer and its licensor(s) shall retain all copyright, trade secret, patent and other proprietary ownership rights in the Software. The Software is

copyrighted and may not be copied, even if modified or merged with other products. You shall not alter or remove any copyright notice or proprietary legend contained in or on the Software. You may transfer all of your license rights in the Software, the related documentation and a copy of this License Agreement to another party, provided that the party reads and agrees to accept the terms and conditions of this License Agreement.

2. DISCLAIMER OF WARRANTY

The Software and related documentation are provided to you “AS IS”. PIONEER AND ITS LICENSOR(S) (for the purpose of provisions 2 and 3, Pioneer and its licensor(s) shall be collectively referred to as “Pioneer”) MAKES AND YOU RECEIVE NO WARRANTY FOR THE SOFTWARE, WHETHER EXPRESS OR IMPLIED, AND ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE FOR THE SOFTWARE ARE EXPRESSLY EXCLUDED. SOME STATES DO NOT ALLOW EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. The Software is complex and may contain some nonconformities, defects or errors. For example, the voice recognition function as implemented by the Software may not recognize your voice. Pioneer does not warrant that the Software will meet your needs or expectations, that operation of the Software will be error-free or uninterrupted, or that all non-con- formities can or will be corrected. Furthermore, Pioneer does not make any representations or warranties regarding the use or results of the use of the Software in terms of its accuracy, reliability or otherwise.

3

3. LIMITATION OF LIABILITY

IN NO EVENT SHALL PIONEER BE LIABLE FOR ANY DAMAGES, CLAIM OR LOSS INCURRED BY YOU (INCLUDING, WITHOUT LIMITATION, COMPENSATORY, INCIDENTAL, INDIRECT, SPECIAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES, LOST PROFITS, LOST INCOME, LOST SALES OR BUSINESS, EXPENDITURES, INVESTMENTS, OR COMMITMENTS IN CONNECTION WITH ANY BUSINESS, LOSS OF ANY GOODWILL, OR DAMAGES) RESULTING FROM THE USE OF OR INABILITY TO USE THE SOFTWARE, EVEN IF PIONEER HAS BEEN INFORMED OF, KNEW OF, OR SHOULD HAVE KNOWN OF THE LIKELIHOOD OF SUCH DAMAGES. THIS LIMITATION APPLIES TO ANY AND ALL CAUSES OF ACTION INDIVIDUALLY OR IN THE AGGREGATE, INCLUDING WITHOUT LIMITATION BREACH OF CONTRACT, BREACH OF WARRANTY, NEGLIGENCE, STRICT LIABILITY, MISREPRESENTATION, AND OTHER TORTS. IF PIONEER’S WARRANTY DISCLAIMER OR LIMITATION OF LIABILITY SET FORTH IN THIS AGREEMENT SHALL OR FOR ANY REASON WHATSOEVER BE HELD UNENFORCEABLE OR INAPPLICABLE, YOU AGREE THAT PIONEER’S LIABILITY SHALL NOT EXCEED FIFTY PERCENT (50%) OF THE PRICE PAID BY YOU FOR THE ENCLOSED PIONEER PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty disclaimer and limitation of liability shall not be applicable to the extent that they are prohibited by any applicable federal, state or local law which provides that such a disclaimer or limitation cannot be waived or preempted.

4. EXPORT LAW ASSURANCES

You agree and certify that neither the Software nor any other technical data received from Pioneer, nor the direct product thereof, will be exported outside Canada except as authorized and as permitted by the laws and regulations of Canada. If the Software has been rightfully obtained by you outside of Canada, you agree that you will not re-export the Software nor any other technical data received from Pioneer, nor the direct product thereof, except as permitted by the laws and regulations of Canada and the laws and regulations of the jurisdiction in which you obtained the Software.

5. TERMINATION

This Agreement is effective until terminated. You may terminate it at any time by destroying the Software. The Agreement also will terminate if you do not comply with any terms or conditions of this Agreement. Upon such termination, you agree to destroy the Software.

6. MISCELLANEOUS

This is the entire Agreement between Pioneer and you regarding its subject matter. No change in this Agreement shall be effective unless agreed to in writing by Pioneer. Pioneer retailers do not have the authority to change this Agreement. This Agreement shall be governed by and construed in accordance with the internal laws of the Province of Ontario and the federal laws of Canada applicable therein. If any provision of this Agreement is declared invalid or unenforceable, the remaining provisions of this Agreement shall remain in full force and effect.

4

Terms and Conditions for the Tele Atlas Data

THIS IS A LEGAL AGREEMENT (THE “AGREEMENT”) BETWEEN YOU, THE END USER, AND TELE ATLAS NORTH AMERICA, INC. (“Tele Atlas”). BY USING YOUR COPY OF THE TELE ATLAS DATA, YOU AGREE TO THE TERMS AND CONDITIONS OF THIS AGREEMENT.

1. Grant of License.

Tele Atlas grants you a non-transferable, nonexclusive license to use the map data and business points of interest information (the “POIs”), (together, the “Data”) contained on these discs, solely for personal, non-commercial use and not to operate a service bureau or for any other use involving the processing of data of other persons or entities. You may make one (1) copy of the Data for archival or backup purposes only but you may not otherwise copy, reproduce, modify, make derivative works, derive the structure of or reverse engineer the Data. The Data contains confidential and proprietary information and materials, and may contain trade secrets, so you agree to hold the Data in confidence and in trust and not to disclose the Data or any portions in any form, including by renting, leasing, publishing, leasing, sublicensing or transferring the Data to any third party. You are prohibited from using the POIs (i) to create mailing lists or (ii) for other such similar uses.

2. Ownership.

The Data is copyrighted by Tele Atlas and its licensors and they retain all ownership rights in the Data. You agree not to alter, remove, obliterate, or obscure any copyright notice or proprietary legend contained in or on the Data.

3. Warranty Disclaimer.

THE DATA IS PROVIDED ON AN “AS IS” AND “WITH ALL FAULTS BASIS” AND TELE ATLAS, ITS LICENSORS, AND ITS LICENSED DISTRIBUTORS AND SUPPLIERS (COLLECTIVELY, “SUPPLIERS”) EXPRESSLY DISCLAIM ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, EFFECTIVENESS, COMPLETENESS, ACCURACY, TITLE AND FITNESS FOR A PARTIC-

ULAR PURPOSE. TELE ATLAS, ITS LICENSORS AND SUPPLIERS DO NOT WARRANT THAT THE DATA WILL MEET YOUR REQUIREMENTS OR THAT THE OPERATION OF THE DATA WILL BE UNINTERRUPTED OR ERROR FREE. NO ORAL OR WRITTEN ADVICE GIVEN BY TELE ATLAS, ITS LICENSORS, SUPPLIERS OR ANY OF THEIR RESPECTIVE EMPLOYEES CREATES A WARRANTY OR IN ANY WAY INCREASES TELE ATLAS’, ITS LICENSORS OR SUPPLIERS LIABILITY AND YOU MAY NOT RELY ON ANY SUCH INFORMATION OR ADVICE. THIS DISCLAIMER IS AN ESSENTIAL CONDITION OF THIS AGREEMENT AND YOU ACCEPT THE DATA ON THIS BASIS.

4. Limitation of Liability.

IN NO EVENT SHALL TELE ATLAS’, ITS LICENSORS’ OR SUPPLIER’ AGGREGATE LIABILITY FOR ALL MATTERS ARISING OUT OF THE SUBJECT MATTER OF THIS AGREEMENT, WHETHER IN CONTRACT, TORT OR OTHERWISE, EXCEED THE AMOUNT PAID BY YOU FOR YOUR COPY OF THE TELE ATLAS DATA. TELE ATLAS, ITS LICENSORS AND SUPPLIERS SHALL NOT BE LIABLE IN ANY MATTER TO YOU FOR ANY SPECIAL, INDIRECT, CONSEQUENTIAL OR INCIDENTAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, AND THE LIKE) ARISING OUT OF THIS AGREEMENT OR THE USE OF OR INABILITY TO USE THE DATA, EVEN IF TELE ATLAS, ITS LICENSORS OR SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

5. Termination.

This Agreement will terminate immediately and automatically, without notice, if you breach any term of this Agreement. You agree that in the event of termination of the Agreement, you shall return the Data (including all documentation and all copies) to Tele Atlas and its suppliers.

6. Indemnity.

You agree to indemnify, defend and hold Tele Atlas, its Licensors, and its Suppliers (including their respective licensors, suppliers, assignees, subsidiaries, affiliated companies, and the respective officers, directors, employees, shareholders, agents and representatives) free and

5

harmless from and against any liability, loss, injury (including injuries resulting in death), demand, action, cost, expense, or claim of any kind or character, including but not limited to attorney’s fees, arising out of or in connection with any use or possession by you of the Data.

7. U.S. Government Rights.

If you are an agency, department, or other entity of the United States Government, or funded in whole or in part by the United States Government, then use, duplication, reproduction, release, modification, disclosure or transfer of this commercial product and accompanying documentation, is restricted in accordance with FAR 12.212 and DFARS 227.7202, and by a license agreement. Contractor/manufacturer is Tele Atlas North America, Inc., 1605 Adams Drive, Menlo Park, CA 94025, (650) 328-3825. The Data is ©1984-2003 by Tele Atlas N.V. and Tele Atlas North America, Inc. ALL RIGHTS RESERVED. For purpose of any public disclosure provision under any federal, state or local law, it is agreed that the Data is a trade secret and a proprietary commercial product and not subject to disclosure.

8. Additional Provisions with respect to Canadian Data only.

a.Warranty Disclaimer.

The Data may include the data of licensors, including Her Majesty the Queen in Right of Canada. Such Data is provided on an “AS IS” AND “WITH ALL FAULTS BASIS” and the licensors, including HER MAJESTY THE QUEEN AND THE MINISTER OF NATURAL RESOURCES EXPRESSLY DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGE- MENT, MERCHANTABILITY, QUALITY, EFFECTIVENESS, COMPLETENESS, ACCURACY, TITLE AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE DATA PRODUCT RESTS WITH YOU. HER MAJESTY THE QUEEN AND THE MINISTER OF NATURAL RESOURCES DO NOT WARRANT THAT THE DATA WILL MEET YOUR REQUIREMENTS OR THAT THE OPERATION OF THE DATA WILL BE UNINTERRUPTED OR ERROR FREE. NO ORAL OR WRITTEN ADVICE GIVEN BY HER MAJ-

ESTY THE QUEEN, THE MINISTER OF NATURAL RESOURCES, TELE ATLAS OR ITS LICENSORS AND EMPLOYEES CREATES A WARRANTY OR IN ANY WAY INCREASES HER MAJESTY THE QUEEN AND THE MINISTER OF NATURAL RESOURCES LIABILITY AND YOU MAY NOT RELY ON ANY SUCH INFORMATION OR ADVICE.

b. Disclaimer of Liability.

IN NO EVENT SHALL THE LICENSORS, INCLUDING HER MAJESTY THE QUEEN IN RIGHT OF CANADA, THE MINISTER OF NATURAL RESOURCES OR THEIR RESPECTIVE OFFICERS, EMPLOYEES OR AGENTS (THE “LICENSORS”), BE LIABLE TO YOU FOR MATTERS ARISING OUT OF THE SUBJECT MATTER OF THE AGREEMENTS, WHETHER IN CONTRACT, TORT OR OTHERWISE.

THE LICENSORS SHALL NOT BE LIABLE TO YOU FOR ANY SPECIAL, INDIRECT, CONSEQUENTIAL, OR INCIDENTAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, AND THE LIKE) ARISING OUT OF THE AGREEMENT OR THE USE OF OR INABILITY TO USE THE DATA, EVEN IF THEY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

c.Indemnification by You.

You shall indemnify and hold harmless the licensors, including Her Majesty the Queen in Right of Canada, the Minister of Natural Resources and their respective officers, employees and agents, from and against any claim, demand or action, irrespective of the nature of the claim, demand or action alleging loss, costs, damages, expenses, or injury (including injury from death) resulting from your authorized or unauthorized use, possession, modification, or alteration of the Data.

9. Miscellaneous.

This is the exclusive and complete Agreement between Tele Atlas and you regarding its subject matter. Nothing in this Agreement shall create a joint venture, partnership or principal-agent relationship between Tele Atlas and you. The internal laws of California shall govern this Agreement and you consent to the jurisdiction of the Northern District of California or the State of California

6

for the County of Santa Clara. Sections 2 - 4 and 7 - 11 shall survive the expiration or termination of this Agreement. This Agreement may be amended, altered, or modified only by Tele Atlas. You may not assign any part of this Agreement without Tele Atlas’ prior written consent. You acknowledge and understand that the Data may be subject to restrictions on exportation and agree to comply with any applicable export laws. In the event that any provision or part of a provision of this Agreement is determined to be invalid, illegal, or unenforceable, such provision or part thereof shall be stricken from this Agreement and the remainder of this Agreement shall be valid, legal, and enforceable to the maximum extent possible. Any notice under this Agreement shall be delivered by courier to Tele Atlas North America, Inc., Attention Legal Department, 1605 Adams Drive, Menlo Park, California 94025 USA.

About the Data for the Map Database

This database was developed and recorded up to January 2004. Changes to streets/highways made after that time may not be reflected in this database.

It is strictly prohibited to reproduce and use any part or the whole of this map in any form without permission from the copyright owner.

If the local traffic regulations or conditions deviate from this data, follow the local traffic regulations (such as signs, indications, etc.) and conditions (such as construction, weather, etc.).

The traffic regulation data used in the map database applies only to standard sized passenger vehicles. Note that regulations for larger vehicles, motorbikes, and other nonstandard vehicles are not included in the database.

Copyright

©1984-2004 Tele Atlas North America, Inc. All Rights

Reserved.

Data by Info USA ©2004 All Rights Reserved.

Canadian Data ©2004 DMTI Spatial Inc., its licensors, and Tele Atlas North America, Inc. Portions of Canadian map data are reproduced under license from Her Majesty the Queen in Right of Canada with permission from Natural Resource Canada, The Queen in Right of Manitoba, and other third party suppliers.

©2005 INCREMENT P CORP. ALL RIGHTS RESERVED

7

Table of Contents

Introduction

License Agreement 1

PIONEER CNDV-50MT [CNDV-50MTP] - for U.S.A. 1

PIONEER CNDV-50MT [CNDV-50MTP] - for Canada 3

Terms and Conditions for the Tele Atlas Data 5 About the Data for the Map Database 7 Copyright 7

Table of Contents 8

Important Safety Information 10

Notes Before Using the System and Additional Safety Information 11

Available models 11 Failure to Operate 11

After-sales service for Pioneer products 11 Purchasing Software Upgrade 11 Product registration 11

Precaution 11

About the AV Head Unit or Display to be Connected 12

Features (Characteristics of this software) 12 Manual Overview 13

To users updating the application program 13 How to use this manual 13

Terminology 14

Map Discs for Navigation System 15 Configuration of data recorded on discs 15

Chapter 1

Basic Operation

Flow from Startup to Termination 17 Basic Navigation 18

Buttons you can use 21 How to Use Menu Screens 21

Main menu 21 Shortcut menu 22

How to Use the Map 23

Switching the current position screen display mode 23

How to view the map of the current location 24 Changing the scale of the map 25

Moving the map to the location you want to see 26

Chapter 2

Setting a Route to Your Destination

Finding Your Destination by Selecting the Type of

Facility 29

Searching for Points of Interest (POI) 29 Finding a POI in your surroundings 30

Searching the facilities around the scroll cursor 30

Setting an Entrance or Exit of a Freeway as Your Destination 31

Searching for Your Destination by Specifying the Telephone Number 31

Route Calculation to Your Home Location or to Your Favorite Location 31

Selecting Destination from the Destination History and Address Book 32

Modifying the Route Calculation Conditions 32 Items that users can change 32

Perform the route calculation of the several route options, and select one 33

Checking the Set Route 34

Checking the set route with the map 34 Checking the set route with text 34 Checking the set route from the Information

menu 35

Recalculating the Route to Your Destination 35 Canceling the Route Guidance 36

Adding Way Points to the Current Route 36 Adding a way point 36

Skipping a way point 37

Deleting a way point from the route 37 Displaying certain POI on the map 37 Using POI shortcuts 38

Chapter 3

Editing the Navigation Utilities

Editing Registered Locations 39 Registering your home and your favorite

location 39

Registering a previous location in the Address Book 40

Editing a location’s information 40

Deleting Address Book or Destination History Information 42

Changing the position of locations registered in the Address Book 42

Setting Areas to Avoid 43 Registering an Area to Avoid 43

Changing or deleting an Area to Avoid 43 Using a PC Card 44

Initializing a PC card 44

Storing the data of registered locations in the PC card 44

Loading registered locations data from a PC card 45

Deleting PC card data 45 Changing Background Picture 45 Checking the Navigation Status 47

Checking sensor learning status and driving status 47

8

Checking the connections of leads and installation positions 47

Chapter 4

Customizing Your Navigation System

Modifying the Default Settings 49 Items Users can Change 49

Chapter 5

Operating Your Navigation System with Voice

Basics of Voice Operation 53

To Ensure Safe Driving 53 Flow of voice operation 53

Voice Commands 54 Common commands 54

Commands for display change 54 Available voice commands related to

navigation 54

Available voice commands related to audio 55 An Example of Voice Operation 55

Tips for Voice Operation 56

Appendix

Installing the Program 57

Combining and Using Pioneer AV Equipment 58 To Ensure Safe Driving 58

About AV Head Units /Displays to be Connected 59

Characteristics of the Navigation System when combined with Pioneer AV Head Unit or AV System Display 60

Touch Panel Operation When Using NAVI Source 60

Cautions when connecting a Rear Display to the Front Display 61

Positioning Technology 61 Positioning by GPS 61 Positioning by dead reckoning 61

Handling Large Errors 62

When the positioning by GPS is impossible 62 Vehicles that Cannot Obtain Speed Pulse Data 63 Conditions Likely to Cause Noticeable Positioning

Errors 63

About the Data being Deleted 65

Limitation of Functions for Areas not Stored on the Disc 65

Other function limitations 66 Troubleshooting 67

Problems in the Navigation screen 67 Messages and how to react to them 69

Route Setting Information 73 Route search specifications 73 Auto Reroute 74

Route highlighting 74

Roads not Used in Calculations 74 Intersection enlargement 74 Tracking 74

Types of the Road Stored in the Disc 75 Roads included in the Route Guidance and

roads not Included 75

Non routable roads (pink color road) 75 Glossary 75

Display Information 77 Main menu 77 Shortcut menu 79

9

Important Safety Information

Before using your Navigation System, be sure to read and fully understand the following safety information:

Read the entire manual before operating this Navigation System.

The navigation features are intended solely as an aid to you in the operation of your vehicle. It is not a substitute for your attentiveness, judgment, and care when driving.

Do not operate this Navigation System if doing so in any way will divert your attention from the safe operation of your vehicle. Always observe safe driving rules and follow all existing traffic regulations. If you experience difficulty in operating the system of reading the display, park your vehicle in a safe location and apply the parking brake before making the necessary adjustments.

Never allow others to use the system unless they have read and understood the operating instructions.

Never use this Navigation System to route to hospitals, police stations, or similar facilities in an emergency. Please call 911.

Route and guidance information displayed by this equipment is for reference purposes only. It may not accurately reflect the latest permissible routes, road conditions, one way streets, road closures, or traffic restrictions.

Traffic restrictions and advisories currently in force should always take precedence over guidance given by the navigation system. Always obey current traffic restrictions, even if the navigation system provides contrary advice.

Failure to input correct information about the local time may result in the navigation system providing improper routing and guidance instructions.

Never set the volume of your Navigation System so high that you cannot hear outside traffic and emergency vehicles.

To promote safety, certain functions are disabled unless the parking brake is applied.

The data encoded in the disc is the intellectual property of the provider, and the provider is responsible for such content.

Keep this manual handy as a reference for operating procedures and safety information.

Pay close attention to all warnings in this manual and follow the instructions carefully.

Do not install the display where it may (i) obstruct the driver’s vision, (ii) impair the performance of any of the vehicle’s operating systems or safety features, including air bags, hazard lamp buttons or (iii) impair the driver’s ability to safely operate the vehicle.

Please remember to wear your seat belt at all times while operating your vehicle. If you are ever in an accident, your injuries can be considerably more severe if your seat belt is not properly buckled.

Using the most current map DVDs will allow for most accurate destination mapping. Upgrade DVDs are available for purchase through your local Pioneer dealer.

Never use headphones while driving.

Do not attempt to install or service your display by yourself. Installation or servicing of the display by persons without training and experience in electronic equipment and automotive accessories may be dangerous and could expose you to the risk of electric shock or other hazards.

10

Notes Before Using the System and Additional Safety Information

Available models

This software can be used with the following models:

AVIC-9DVD, AVIC-90DVD, AVIC-80DVD, AVIC88DVD, AVIC-880DVD

If the program has not been updated “Installing the Program” on page 57

Failure to Operate

Should the navigation system fail to operate properly, contact your dealer or the nearest authorized Pioneer service facility.

After-sales service for Pioneer products

Please contact the dealer or distributor from where you purchased the product for its aftersales service (including warranty conditions) or any other information. In case the necessary information is not available, please contact the companies listed below:

Please do not ship your product to the companies at the addresses listed below for repair without making advance contact.

U.S.A

CANADA

Pioneer Electronics

Pioneer Electronics of

(USA) Inc.

Canada, Inc.

CUSTOMER SUP-

CUSTOMER

PORT DIVISION

SATISFACTION

P.O. Box 1760

DEPARTMENT

Long Beach, CA

300 Allstate Parkway

90801-1760

Markham, Ontario

800 421-1404

L3R OP2

 

1-877-283-5901

For warranty information, please see the Limited Warranty sheet included with your product.

Purchasing Software Upgrade

Using the most current map DVDs will allow for most accurate destination mapping. Upgrade DVDs are available for purchase through your local Pioneer dealer.

Product registration

Visit us at the following site:

1.Register your product. We will keep the details of your purchase on file to help you refer to this information in the event of an insurance claim such as loss or theft.

2.Receive updates on the latest products and technologies.

3.Download owner's manuals, order product catalogs, research new products, and much more.

4.Receive notices of software upgrades and software updates.

Precaution

Parking brake interlock

Certain functions offered by this Navigation System could be dangerous if used while driving. To prevent them being used while in motion, there is an interlock with your vehicle’s parking brake. If you attempt to use these functions during driving, their onscreen touch keys may be indicated in gray and inoperable. If so, stop in a safe place, apply the parking brake, then operate.

To ensure safe driving

To avoid the risk of accident and the potential violation of applicable laws, the navigation system is not for use with a video screen (DVD video, TV, etc.) that is visible to the driver.

In some countries or states the viewing of images on a display inside a vehicle even by persons other than the driver may be illegal. Where such regulations apply, they must be obeyed.

Before viewing the DVD video using the navigation unit’s built-in DVD player, first stop the vehicle in a safe place and apply the parking brake.

The display is controlled in combination with the brake to prevent the display of the video unless the parking brake is applied.

11

To watch a DVD or TV, park your vehicle in a safe place and apply the parking brake.

Color difference of the map display between day and night

Night display

The examples in this manual are illustrated using the daytime display. When driving at night, the colors you see may differ from those shown.

To use this function, the Orange/white lead of the navigation unit must be connected correctly.

“Day/Night Display” Page 50

About playing the DVD video

DVD videos and CDs can be played on AVIC9DVD, AVIC-90DVD. When using AVIC-9DVD, refer to the DVD section in the “Operation Manual” provided with AVIC-9DVD. When using AVIC90DVD, refer to the DVD section in their respective “Hardware Manual”.

About the AV Head Unit or Display to be Connected

You need an AV head Unit or Display with a touch panel capability to use this software. If any display without a touch panel feature is connected, the software will not work properly. Make sure to use a display suitable for the system.

“About AV Head Units /Displays to be Connected” Page 59

Features (Characteristics of this software)

Touch panel key operation

It is possible to operate the navigation function and the Audio function by using touch panel key.

Compatible with the Voice Recognition System

Using the microphone will enable voice operation for both the navigation and AV functions*.

*: You need a display with AV function.

Variety of View Modes

Various types of screen display can be selected for navigation guidance.

– Map View, Driver‘s View, Route View, Guide View

Wide Variety of POI Information

Approximately 11 million POIs are included in this database as of January 2004.

Some POI information may not be accurate or may become inaccurate through the passage of time. Please directly contact the POI to verify the accuracy of the information about the POI which appears in this database. POI information is subject to change without notice.

Auto Reroute Function

If you deviate from the set route, the system will re-calculate the route from that point so that you remain on track to the destination.

This function may not work for certain areas.

Assign an Original Image as a Background Image

You can store your own pictures on a

PC card in JPEG format and import original images in this format. These imported images can be set as a background image.

Imported original images will be stored in the memory, but saving cannot be guaranteed completely. If original image data is deleted, set the PC card again and re-import the original image.

12

Manual Overview

This manual provides the important information you need to make full use of your new Navigation System. The beginning sections outline the Navigation System and describe its basic operation. The later sections describe the details of the navigation functions.

Please note that when you have decided what you want to do, you can find the page you need from the “Table of Contents”.

If you want to check the meaning of each item displayed on the screen, you will find the necessary page from the “Display Information” at the end of the manual.

To users updating the application program

Before using this system, check that the program has been updated. If not, upgrade it by referring to “Installing the Program” on page 57.

How to use this manual

For reasons of safety, it is particularly important that you fully understand your Navigation System before using it. Be sure to read Introduction and Chapter 1 in particular.

1

2

3

4

5

Basic Operation

If you want to use the Navigation System immediately, please read this section. It will explain the basics of operating this system, including items appearing on the display and how to use the different menus.

Setting a Route to Your Destination

This section describes various ways of searching the destination, changing the route search conditions, and the route operation during route guidance.

Editing the Navigation Utilities

Describes convenient functions for navigation, including how to organize information on places you have visited and how to store data on the PC card.

Customizing Your Navigation System

The behavior of your Navigation System depends on a number of settings. If you need to change any of the initial settings (default settings), read the relevant section of this chapter.

Operating Your Navigation System with Voice

Describes navigation operations such as searching the destination and performing audio operations by voice.

Appendix

Read the appendix to learn more about your Navigation System and such information as the availability of after-care. Please see “Display Information” at the end of this manual for checking the details of each item on the menu.

13

Terminology

Before moving on, take a few minutes to read the following information about the conventions used in this manual. Familiarity with these conventions will help you greatly as you learn how to use your new equipment.

Buttons on your Navigation Unit are described in ALL CAPITAL, BOLD lettering: e.g.)

NAVI (or POS) button, NAVI MENU button.

Items in the different menus or touch keys available on the screen are described in quotations (“”) and bold:

e.g.)

Destination”, “Settings”.

Extra information, alternative use and other notes are presented like this: e.g.)

After removing the disc from the slot, keep it in the case.

The references are indicated like this: e.g.)

Setting the Route Options Page 32

14

Map Discs for Navigation System

Configuration of data recorded on discs

The map for this navigation system is supplied on two discs: one for the west and the other for the east. Please set the disc to use according to your destination or current location.

The areas recorded on each disc are as follows:

West area disc

East area disc

Removing the disc and inserting another disc causes the navigation system to automatically restart and reload the new route. (This automatic “Reroute” operation cannot be canceled.)

15

16

Chapter 1

Basic Operation

Flow from Startup to Termination

If the program is not installed, see page 57 and install the program.

At first, please confirm the positions of the following features using the navigation’s “Hardware Manual”, “Operation Manual” and display’s “Operation Manual”.

Disc loading slot

NAVI/AV button

NAVI MENU button

1 Start the engine.

After a little time, the navigation opening screen comes on for a few seconds. Then, a message screen is displayed.

If the disc is not set, the message asking to insert the disc appears. After you set the disc correctly, your Navigation System starts up.

2 Insert the Pioneer DVD map disc to the disc loading slot.

3 Press the NAVI/AV button to switch the Navigation map screen.

Pressing the NAVI/AV button switches between the navigation map screen and the audio screen.

4 Check the details of the cautionary message and touch “OK”.

You can operate the Navigation System by touching keys displayed on the screen.

If the route is already set, it changes to route guidance mode. The map of your surroundings is displayed.

How to read the current position screen Page 24

Setting the time Page 58

Starting the operation with voice commands only Page 51

You can press the TALK (or VOICE) button of the steering remote control to proceed instead of touching “OK”.

Touch keys which are not available at this time are grayed out.

Be sure to touch the touch keys with a finger. Touch keys cannot be operated by a pen or similar object.

5 Press the NAVI MENU button.

Displays the main menu.

6 Searches the destination and gives route guidance.

Specifying the address and searching the destination Page 18

Searching the destination by map Page 27

Other search methods Page 29 to 32

7 Turn off the vehicle engine.

This Navigation System is also turned off.

Until the vicinity of the destination is reached, the set route will not be deleted automatically even if the power is turned off.

Operation Basic 1 Chapter

17

Basic Navigation

The most frequently used function is the Address Search, in which the address is specified and the destination searched. This section describes how to use the Address Search and the basics of using the Navigation System.

For safety reasons, you cannot use these basic navigation functions while your vehicle is in motion. To enable these functions, you must stop in a safe place and apply the parking brake.

Basic Operation Chapter 1

Basic flow of operation

1 Park your vehicle in a safe place, and apply the parking brake.

2 Insert the Pioneer DVD map disc to the disc loading slot.

3 Press the NAVI MENU button to display the Main menu.

4 Select “Destination” from the Main menu.

5 Select the method of searching for your destination.

6 Enter the information about your destination.

7 Your Navigation System sets the route to your destination, and the map of your surroundings appears.

8 After releasing the parking brake, drive in accordance with the navigation information, subject of course to the important safety instructions noted on page 10 to 12.

18

1 Press the NAVI MENU button to display the main menu.

2 Touch “Address Search”.

Selects the method for searching the destination.

Return Home Page 31

Go to Page 31

POI Search Page 29

Vicinity Search Page 30

Address Book Page 32

Destination History Page 32

Freeway Search Page 31

Telephone Search Page 31

Cancel Route Page 36

3 Touch “Zone code key”.

If the destination is in another zone, this changes the zone setting.

Once the zone has been selected, you only have to change zones when your destination is outside of the zone you have selected.

Zone code key

4 Touch the zone code of the destination and touch “OK”.

Modifies the zone setting and returns you to the previous display.

5 Input the house number and touch “OK”.

Touch the characters you wish to input.

:

The input text is deleted letter by letter from the end of the text. Continuing to press deletes all of the text.

“Back” :

Returns you to previous screen.

Also input a prefix to the house number.

If the house number you have input is not found among subsequently selected “Street” or “City” data, a message appears saying that the address has not been found. In that case, try inputting the house number again.

Touching “OK” with no input allows you to specify and search a street name or the name of the city or area first.

6 Input the street name.

Touch the letter you wish to input. If the next screen is not automatically displayed even though the street name is entered, try touching “OK”.

The input text.

The number of applicable candidates.

“City” :

Touch if you wish to first specify the destination city or area.

:

The input text is deleted letter by letter for the end of the text. Continuing to press deletes all of the text.

“Sym.” :

You can input text with marks such as “&”and “+”.

Operation Basic 1 Chapter

19

Basic Operation Chapter 1

“0-9” :

You can input text with numbers.

“Back” :

Returns you to previous screen.

For example, for “Early California Ct”, you can just enter part of the name, such as “California”.

While entering characters, if there is only one candidate following the next, that is automatically entered.

When touching “Back” on the text input screen to return to the previous screen, you may not be able to input text. In such a case, delete the letters entered in the text box.

Searching your destination after specifying the name of city or area

You can narrow down the searching candidates by initially specifying the name of city or area where your destination is located. Inputting the name of the city or area then selecting the destination city or area from the list returns you to the Street Name input screen. Now input the street name, select the street from the list, and proceed to step 9.

In the selected area, if you touch “City” without entering the name of city or area, you can check the list of the cities or areas, which you have searched in the past. (This item cannot be selected when searching by the name of city or area for the first time with this system or when you have selected an area that you have never searched before.)

7 Touch the street from the list.

Scroll bar

Touching the or on the scroll bar scrolls you through the list and allows you to view the remaining items.

Searching the destination by map Page 27

In the case of an item that cannot be displayed in a single line, touching the to the right of the item allows you to see the whole line.

If only one location is found from the list, route calculation starts after pressing the item.

Touching the specifies the selected street and streets intersecting it, allowing you to set an intersection as your destination. This is useful when you don’t know the house number of your destination or cannot input the house number of the specified street.

Touching the displays a map of the place you have selected. (Candidate place names may appear in the list screen.)

8 Input the destination city or area.

If the list screen is displayed, proceed to step 9.

9 Touch the city or area where your destination is located.

Route calculation starts. When the route calculation is completed, the map of your surroundings appears. (The route is displayed in highlighted color.)

20

If the selected street is very long and passes through several cities or areas, the screen for entering the name of the city or area appears.

If you did not input the house number in Step 5, the house number input screen comes up after the “Street” and “City” are determined. You should now input the house number (perform Step 5).

If there is more than one place for the house number input, or if there is no such house number in that place, displays a list of a certain range. To start the route calculation, touch the range within the list you wish to specify as the destination.

You can also see the destination on the map by touching the to the right of the list.

Searching the destination by map Page 27

If you press the NAVI (or POS) button during route calculation, the calculation is canceled and the map display appears.

When performing a destination search with the route already set, select whether to regard the specified area as your destination and search for a new route, or search for a route via that area.

Adding way points to the route Page 36

Once searched for, a location is automatically stored in the “Destination History”Page 40

10Drive in accordance with the screen and voice information.

Your Navigation System gives you the following information with the timing adjusted to the speed of your vehicle:

Distance to the next turning point

Direction of travel

Road number of the freeway

Way point (If this is set)

Your destination

How to view the screen Page 23

Searching for another route Page 35

Canceling route guidance Page 36

Touching the or pressing the remote control‘s GUIDE button allows you to hear

the information again.

If you deviate from the route with the Guidance set to Route View or Guide View and enter a street not recorded on the disc, the screen changes to Map View. When you return to the route, the screen returns to the original mode and resumes route guidance.

If you stop at a gas station or a restaurant during the route guidance, your Navigation System remembers your destination and route Information. When you start the engine and get back on the road, the route guidance resumes.

Buttons you can use

The status of the buttons appearing on the screen is indicated by their color.

Depending on the function the navigation is performing, you can touch some buttons, while other buttons are not available.

Blue touch key:

The button is operable.

Dark gray touch key:

The function is not available (e.g., operation is prohibited while driving).

Light gray touch key:

The function is not available for areas not stored on the disc.

Touching this button activates a message indicating that the function is not available.

How to Use Menu Screens

The basic operation of the navigation is performed by using menus.

There are two types of menu: the “Main menu” and the “Shortcut menu”.

Main menu

You use this menu for basic operation of your Navigation System.

Operation Basic 1 Chapter

21

Pioneer AVIC-90DVD, AVIC-88DVD, CNDV-50MT, CNDV-50MTP, AVIC-9DVD User Manual 2

1 With the map displayed, press the NAVI MENU button.

2 To change to the menu you want to use, touch the name of the menu displayed at the top of the screen.

The main menu is divided into four: “Destination”, “Information”, “Route Options”, and “Settings”.

3 If you want to return to the map, press the NAVI (or POS) (or NAVI MENU) button.

Destination menu

Route Options menu

Used to specify the conditions for setting the route to the destination.

Setting the Route Options Page 32

Settings menu

Basic Operation Chapter 1

Select the destination search method. Also the set route can be canceled from this menu.

Specifying the address and searching the destination Page 18

Searching the destination by map Page 27

Other search methods Page 29 to 32

Information menu

Used to check the route you set or check the navigation status.

You can use “Route Profile” and “Route Scroll” only when a route has been entered.

Checking the set route Page 34

Checking the navigation status Page 47

Using a PC card Page 44

Set the navigation functions so they can be used easily.

Settings menu Chapter 4

If the contents of the menu are not fully displayed on the screen, touch “Next” to view the remaining contents.

Shortcut menu

Shortcuts allow you to perform various tasks, such as route calculation for the location indicated by the cross pointer, or registering a location in the Address Book, faster than using the Main menu.

1 When the map is displayed, briefly touch any part of the map.

If you continue to touch the map, it will start scrolling.

Moving the map to view the part you want to see Page 26

22

:Destination

Displayed when the map is scrolled. Set the route to the place specified with the cross pointer.

Searching the destination by map Page 27

:Chg.Route

Can be selected only during route guidance. You can add changes to the route in the route guidance.

Searching another route Page 35

Detour for a specified distance Page 35

Checking the route Page 34

Canceling the route guidance Page 36

Skipping a way point Page 37

:Registration

Registering the location indicated by the cross pointer to Address Book.

Registering a place Page 40

:Vicinity Search

You select a location with the cross pointer. Nearby POIs (Points Of Interest) will also be found.

Searching the facilities surrounding a certain place Page 30

:Overlay POI

Displays on the map the mark for surrounding facilities (POI).

Viewing POI information Page 26

:Note

You can check details of the item pointed by the scroll cursor.

Viewing the information of a specified location Page 26

How to Use the Map

Most of the information provided by your Navigation System can be seen on the map. You need to get to know how the information appears on the map.

Switching the current position screen display mode

This section describes how to display the current position screen and change the map display mode.

There are four types of map display.

Map View

Driver’s View

Guide View (during route guidance only)

Route View (during route guidance only)

1 Press the NAVI (or POS) button to display a map of the area around your current position.

2 Press the NAVI (or POS) button again.

3 Touch the mode name or press the NAVI (or POS) button to select the mode you want to display.

If the mode is selected by pressing the NAVI (or POS) button, the screen automatically switches to the selected map display mode after 4 seconds.

Operation Basic 1 Chapter

23

Loading...
+ 57 hidden pages