Pioneer BR-360 User Manual

0 (0)
Pioneer BR-360 User Manual

Operating

Instructions

REMOTE CONTROL

BR-360

© 2001, Pioneer New MediaTechnologies, Inc.

2265 East 220th Street Long Beach, CA 90810 USA telephone: (310) 952-2111

http://www.pioneerbroadband.com

‹C 029 AACA›

What it does

 

BR-360 keypad

The BR-360 operates all Pioneer Voyager BD- V1000/BD-V3000 series Digital HomeTerminals, as well as some home terminal models from other manufacturers.You need the BR-360 to experience all the viewing options Voyager offers, because you can’t access all Voyager functions from the HomeTerminal front panel keys or from other brand remotes.

The BR-360 also supports basic remote control functions for nearly allTVs, VCRs, stereo receivers/ amplifiers, and some DVD players.You don’t have to remember to switch “modes” with the BR-360 each key always transmits to one device.

This instruction sheet contains setup instructions and device codes. Keep this sheet in case you need to set up the BR-360 remote again in the future.

Batteries

Two AA batteries power the BR-360.

To install batteries:

1 Push the battery cover tab toward the center, and lift the cover off.

 

+

 

+

+

AA

 

AA

AA

 

 

 

 

 

 

AA

 

 

 

 

+

 

 

 

2 Insert two fresh AA batteries, in the directions shown inside the battery compartment.

AA

+

3Replace the battery cover.

The BR-360 operates your Voyager HomeTerminal, TV, VCR, and audio equipment (stereo receiver/ amplifier). Certain keys only operate certain devices. Keys that work together are clustered to make them easier to locate.

Each key is described below. These are basic descriptions only. Refer to the manual(s) that came with your HomeTerminal to learn how to use the keys.

The device(s) in parentheses are those the key will operate. For example, note that item 18 below (CH +/–) will change the channel on the Voyager terminal only, not on the TV or the VCR. Before you can use the BR-360 to operate your TV and other equipment, see Programming your BR-360 below to learn how to set up the BR-360.

Note: Some keys designated “Voyager” may not operate with some versions of home terminal hardware or software.

Indicator

(1)Indicator light

Blinks when the remote transmits a command. Also helps you during setup.

Power control

(2)AUD,TV, CBL, VCR: Device power keys

(Audio,TV, Voyager, VCR/DVD player)

Turn power of these devices on/off.

On-screen operations

(3)MENU: Main menu access key

(Voyager)

Displays the menu of Voyager features.

(4)INFO: Information key (Voyager)

Displays information about the program currently playing or highlighted in the program guide.

(5)GUIDE: Interactive program guide key

(Voyager)

Displays the program guide listings.

(6)5 , 4 , 6 , 3: Display navigation keys (Voyager)

Highlight an item from the on-screen choices.

(7)SELECT: Display action key (Voyager)

Activates the highlighted item.

(8)PAGE +/–: Page rocker key (Voyager)

Accesses pages above or below the information currently displayed.

(9)SETTINGS: Voyager settings menu key

(Voyager)

Displays the menu of preferences for your Voyager home terminal.

(10)EXIT: Exit key (Voyager)

Hides all on-screen graphics and returns you to regular TV viewing.

(11)HELP: Help access key (Voyager)

Displays helpful information about Voyager operation.

(12)A, B, C: Function keys (Voyager)

Make direct selections from on-screen menus.

(13)DAY +/–: Program guide day skip keys

(Voyager)

Skip forward or backward a whole day in the program guide.

Channel/volume control

(14)FAV: Favorite channel recall key

(Voyager)

Tunes channels previously stored in the Voyager terminal’s favorite channel memory.

(15)LAST: Last channel recall key

(Voyager)

Accesses the previously tuned channel.

(16)MUTE: Mute key (Audio,TV, or Voyager)

Silences the audio. Press to activate. Press this key again to restore sound to the previous level.

(17)VOL +/–: Volume rocker key (Audio,TV, or Voyager)

Raises or lowers the sound level.

(18)CH +/–: Channel rocker key (Voyager)

Selects the next higher or lower channel.

(19)0 – 9: Numeric keys (Voyager)

Directly tune channels by number. Also make numeric entries in on-screen menus.

(20)ENTER: Enter key (Voyager)

Immediately tunes the channel number you’ve just entered.

BR-360 programming

(21)SETUP: BR-360 setup key

Starts programming your BR-360.

VCR/DVD/VOD operations

(22)7,4, 8, <, ;: Transport keys

(VCR, DVD player, or Voyager)

Activate play (4), rewind (7), fastforward (8), stop (<), and pause (;) functions of your VCR or DVD player.Take the same actions on Video-On-Demand programming through the Voyager terminal. Determined by position of VCR/ VOD toggle switch (24).

(23)= : Record key (VCR)

Starts recording on your VCR.

(24)VCR/VOD: VCR/VOD toggle switch

Selects the device to which the BR-360 transport keys (22) transmit. Slide to “VCR” to send transport/pause commands to your VCR or DVD player. Slide to “VOD” to pause, scan forward/backward, stop, and resume play of a current Video-On- Demand program.

(25)TV/VCR: TV/VCR key (VCR)

Toggles the VCR’sTV/VCR switch.

RF Bypass control

(26)BYPASS: RF Bypass key (Voyager)

Toggles the Voyager’s optional RF Bypass switch.

Programming your BR-360

Setup for Voyager Home Terminal

No setup is required.The BR-360 is ready to run the Voyager HomeTerminal.

Setup for TV operation

Find your TV brand and its three-digit codes under TV setup codes on the back of this sheet. If your brand is not listed, go to Searching the code library instead.

1Turn on the TV.

2Press and hold SETUP. The indicator light comes on. Keep holding until the light goes off.

3Release SETUP. The indicator light blinks once.

4Press TV.

5Enter the three-digit code. Indicator light blinks twice to confirm acceptance.

6Point the BR-360 toward theTV.

7Press TV. Did theTV turn off?

Yes: Setup complete. Write down the threedigit setup code below for future reference.

No: Try setup again starting from step 2, using the next code listed for your brand. If you’ve tried all codes for your brand without success, use the method under Searching the code library.

MyTV setup code is:

Setup for VCR or DVD player operation

You can choose to control either your VCR or your DVD player. For VCR setup, find the VCR brand and its three-digit codes under VCR setup codes on the back of this sheet. If your brand is not listed, go to

Searching the code library.

1 Turn your VCR on.

2Press and hold SETUP. The indicator light comes on. Keep holding until the light goes off.

3Release SETUP. The indicator light blinks once.

4Press VCR.

5Enter the three-digit code. Indicator light blinks twice to confirm acceptance.

6Point the BR-360 toward the VCR.

7Press VCR. Did the VCR turn off?

Yes: Setup complete. Write down the three-digit setup code below for future reference.

No: Try setup again starting from step 2, using the next code listed for your brand. If you’ve tried all codes for your brand without success, try the method under Searching the code library.

For DVD player setup, find your DVD player brand and its three-digit codes under DVD player setup codes on the back of this sheet. Then follow the above VCR instructions using your DVD player and code.

My VCR or DVD player setup code is:

Setup for stereo receiver/amplifier operation

Find the audio equipment brand and its threedigit codes under Stereo receiver/amplifier setup codes on the back of this sheet. If your brand is not listed, go to Searching the code library.

1Turn your receiver (or amplifier) on.

2Press and hold SETUP. The indicator light comes on. Keep holding until the light goes off.

3Release SETUP. The indicator light blinks once.

4Press AUD.

5Enter the three-digit code. Indicator light blinks twice to confirm acceptance.

6Point the BR-360 toward the receiver.

7Press AUD. Did the receiver turn off?

Yes: Setup complete. Write down the three-digit setup code below for future reference.

No: Try setup again starting from step 2, using the next code listed for your brand. If you’ve tried all codes for your brand without success, try the method under

Searching the code library.

My receiver/amplifier setup code is:

Loading...
+ 1 hidden pages