Phoenix Gold SD1300.1, SD1300.5 User Manual

4 (1)

AMPLIFIER MANUAL

MANUEL DE L’AMPLIFICATEUR

Model: SD1300.1, SD1300.5

Features:

Caractéristiques:

• High Efficiency Class DTopology

• Topologie de classe D de gamme complète

• Compact Size for Easy Installation

• Petit format pour faciliter l’installation

• High and Low Pass Crossovers

• Filtres croisés passe-haut et passe-bas

• Robust Unregulated Power Supply

• Alimentation électrique robuste non réglementée

• Surface Mount ComponentTechnology

• Technologie de composant monté en surface

Panel Mounted RCAs

• Amplificateurs à couplage RC montés sur des panneaux

• Direct Insert Power and SpeakerTerminals

• Terminaux d’alimentation et de haut-parleurs à insertion directe

• Audio Precision Quality ControlVerification

• Vérification du contrôle de la qualité de la précision audio

HighTemperature Plexiglass cover

• Couvercle de plexiglas résistant aux températures élevées

• Remote subwoofer level control included

• Niveau de contrôle de passe-bas inclus

© 2011 Phoenix Gold • www.phoenixgold.com

SPECIFICATIONS

SD1300.1 SPECIFICATIONS

Frequency Response:

± 1dB from 20Hz to 300Hz

Signal to Noise Ratio:

>90dB

Low Pass Crossover:

18dB per Octave

Subsonic Filter:

12dB per Octave

Low Pass Crossover Range:

30Hz to 300Hz

Subsonic Crossover Range:

10Hz to 55Hz

Bass Boost @ 45Hz:

0 to +18dB

Low Level Input Range:

200 millivolts to 8 volts

Lowest Recommend Load:

1 ohm

Typical Efficiency:

70%

Damping Factor:

Greater than 200

SD1300.5 SPECIFICATIONS

Frequency Response:

± 1dB from 20Hz to 20kHz

Signal to Noise Ratio:

>100dB

High Pass Crossovers:

12dB per Octave

Low Pass Crossover:

18dB per Octave

High Pass Crossover Range:

15Hz to 250Hz

Low Pass Crossover Range:

30Hz to 300Hz

Bass Boost @ 45Hz:

0 to +18dB

Low Level Input Range:

200 millivolts to 8 volts

Front and Rear Channels Lowest Load:

4 ohms Bridged or 2 ohms Stereo

Subwoofer Channel Lowest Load:

2 ohm

Typical Efficiency:

70%

Damping Factor

Greater than 200

Note: All SD amplifiers operate correctly up to 14.4 volts. Do not operate the amplifier above 14.4 volts.The amplifier will engage its overvoltage protection, the result is no audio output on one or more channels.

Amplifier Owner’s Manual

RMS Power 14.4Vdc ≤ 1%THD

900 x 1 @ 2 ohms

 

1300 x 1

@ 1 ohm

Dynamic Power 14.4Vdc >1%THD

1200 x 1

@ 2 ohms

 

1600 x 1

@ 1 ohm

Recommended Fuse Size:

120 amp

Power/GroundWire Size:

4 Gauge

 

Dimensions (Includes Mounting Feet):

14.33”L x 6.93”W x 2.0”H

 

364mm L x 176mmW x 51mm H

Dimensions (IncludesTerminals):

14.96”L x 6.93”W x 2.0”H

 

380mm L x 176mmW x 51mm H

RMS Power 14.4Vdc ≤1%THD

80 x 4 @ 4 ohms Stereo

 

125 x 4 @

2 ohms Stereo

 

250 x 2 @

4 ohms Bridged

 

plus

 

 

500 x 1 @

4 ohms

 

800 x 1

@

2 ohms

Dynamic Power 14.4Vdc >1%THD

95 x 4 @ 4 ohms Stereo

 

150 x 4

@

2 ohms Stereo

 

300 x 2

@

4 ohms Bridged

 

plus

 

 

700 x 1

@

4 ohms

 

1000 x 1 @ 2 ohms

Recommended Fuse Size:

100 amp

 

Power/GroundWire Size:

4 Gauge

 

Dimensions (Includes Mounting Feet):

14.33”L x 6.93”W x 2.0”H

 

364mm L x 176mmW x 51mm H

Dimensions (IncludesTerminals):

14.96”L x 6.93”W x 2.0”H

 

380mm L x 176mmW x 51mm H

© 2011 Phoenix Gold • www.phoenixgold.com

Amplifier Owner’s Manual

SD1300.1

MONOBLOCK POWER AMPLIFIER

INPUT

Connect preamp signal cables from the head unit to these terminals.

CROSSOVER FREQUENCY

Controls the lowpass crossover point for the speaker outputs.

BASS BOOST

Variable bass boost from 0 to +18dB @ 45Hz.

REMOTE LEVEL CONTROL

This port is for connecting the subwoofer remote level control.This allows up to 20dB of volume adjustment. This is not a bass boost, it controls the level of the low pass signal.

NOTE:This control is not compatible with the Phoenix Gold LPL44 level control.

SENS

Used to reach maximum amplifier power with a wide variety of headunits.

SUBSONIC CROSSOVER FREQUENCY

Controls the highpass crossover point for the speaker outputs to eliminate extreme low frequencies.

RMD

Optional RMDVoltage Display plugs into this port. Sold separately.

INPUT

L

REMOTE

 

 

 

RMD

X-OVER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FREQ.

BASS

SUBSONIC

SENS

 

 

PROTECT

 

 

 

 

 

 

 

 

 

 

 

 

R

 

 

POWER

 

30Hz 300Hz

0dB 18dB

10Hz 55Hz

MIN MAX

SPEAKER

 

 

 

 

 

 

 

 

 

 

GROUND

R

+ 12V

 

FUSE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GROUND

REMOTE

+ 12V

 

40A

 

40A

 

40A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+12V

SPEAKER OUTPUTS

This must be connected to the fused positive terminal (+12V) of the car’s

Used to connect the amplifier to speakers. SD1300.1 minimum impedance

battery.The fuse must be located within 18 inches of the battery.

is 1 ohm.

REMOTE

 

This must be connected to switched +12V, usually a trigger wire coming

 

from the head unit or ignition.

 

GROUND

 

This must be connected to the negative terminal of the car’s battery or

 

bolted to a clean, unpainted part of the chassis of the vehicle.

 

NOTE:Visible through the plexiglass cover, a single blue power LED is located in the lower corner of all SD amplifiers.

© 2011 Phoenix Gold • www.phoenixgold.com

Phoenix Gold SD1300.1, SD1300.5 User Manual

Amplifier Owner’s Manual

SD1300.5

5 CHANNEL POWER AMPLIFIER

FRONT, REAR AND SUB INPUTS

Connect preamp signal cables from headunit to these inputs.The front AND rear inputs must be used, if only the front input is used then the rear speaker outputs will have no output signal.The Sub Input may or may not be used see SUB INPUT SWITCH for more information.

HPF AND LPF CROSSOVER FREQUENCY

Controls the crossover point for the speaker outputs.

REMOTE LEVEL CONTROL

This port is for connecting the subwoofer remote level control.This allows up to 20dB of volume adjustment. This is not a bass boost, it controls the level of the subwoofer channel only.

NOTE:This control is not compatible with the Phoenix Gold LPL44 level control.

BASS BOOST

Variable bass boost from 0 to +18dB @ 45Hz for the subwoofer channel only.

SENS

Used to reach maximum amplifier power with a wide variety of headunits.

SUB INPUT SWITCH

IN: Subwoofer speaker output is fed by the sub Input. If the headunit or processor has a subwoofer low level output use this setting.

OUT: Subwoofer speaker output is fed by the front input and the sub Input is not used. If the headunit or processor only has front and rear low level outputs use this setting.

RMD

Optional RMDVoltage Display plugs into this port. Sold separately.

 

 

SUB INPUT

 

 

 

 

 

 

FRONT INPUT

REAR

 

L

 

 

 

 

 

 

 

FL

RL

 

 

SUB INPUT

SENS

BASS BOOST

 

LPF

 

PROTECT

REMOTE

 

 

 

 

 

 

 

 

RMD

 

 

 

 

 

 

 

 

 

 

 

R

SUB

FRONT

MIN

MAX

0dB

18dB

30Hz

300Hz

 

 

HPF

SENS

HPF

SENS FR

RR

POWER

 

15Hz

250Hz

MIN

MAX

15Hz

250Hz

MIN

MAX

 

 

 

 

 

 

 

 

 

 

 

 

 

FR

SUB.

GROUND

R

+ 12V

 

GROUND

REMOTE

+ 12V

RL

RR

SUB.

 

 

 

+12V

This must be connected to the fused positive terminal (+12V) of the car’s battery.The fuse must be located within 18 inches of the battery.

REMOTE

This must be connected to switched +12V, usually a trigger wire coming from the head unit or ignition.

GROUND

This must be connected to the negative terminal of the car’s battery or bolted to a clean, unpainted part of the chassis of the vehicle.

SPEAKER OUTPUTS

Used to connect the amplifier to speakers. Front and Rear Channel minimum impedance is 4 ohms bridged or 2 ohms stereo. Subwoofer channel minimum impedance is 2 ohms. Use Right + and Left - to bridge the front or rear channels, the subwoofer channel is not bridgeable.

NOTE:Visible through the plexiglass cover, a single blue power LED is located in the lower corner of all SD amplifiers.

© 2011 Phoenix Gold • www.phoenixgold.com

Loading...
+ 8 hidden pages