Pentair KX-HCM110A, BL-C1A, BB-HCM381A, BB-HCM331A, BL-C111A User Manual

...
0 (0)
ScreenLogic Video & Lighting Protocol Adapter Users and Installation Guide
User’s and Installation Guide
ScreenLogic
®
Video & Lighting Protocol
Adapter
ScreenLogic Video & Lighting Protocol Adapter User’s and Installation Guide
ScreenLogic
®
The following items are included in the kit.
Kit contents
ScreenLogic Video & Lighting Protocol Adapter (P/N 520854Z)
AC/DC power adapter
RJ45 cable
DB9M to RJ45 adapter
User’s and Installation Guide (this manual)
© 2008 Pentair Water Pool and Spa, Inc. All rights reserved.
1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000
10951 West Los Angeles Ave., Moorpark, CA 93021 • (800) 553-5000
IntelliTouch
®
, ScreenLogic
®
and Pentair Water Pool and Spa
®
are registered trademarks of Pentair Water Pool
and Spa, Inc. and/or its affiliated companies in the United States and/or other countries. Unless noted, names
and brands of others that may be used in this document are not used to indicate an affiliation or endorsement
between the proprietors of these names and brands and Pentair Water Pool and Spa, Inc. Those names and
brands may be the trademarks or registered trademarks of those parties or others.
P/N 520936 - Rev A - 03/03/2008
i
FCC Regulatory Safety Notice - This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Modifications not expressly approved by the party responsible for FCC compliance could
void the user’s authority to operate the equipment.
Related manuals - Download the IntelliTouch ScreenLogic User’s Guide
(P/N 520493) at:
http://www.pentairpool.com/siteimages/ScreenLogic_Users_Guide.pdf
Technical Support
Sanford, North Carolina (8 A.M. to 5 P.M. ET)
Moorpark, California (8 A.M. to 5 P.M. PT)
Phone: (800) 831-7133 - Fax: (800) 284-4151
IC Regulatory Notice
Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
ScreenLogic Video & Lighting Protocol Adapter User’s and Installation Guide
Contents
ScreenLogic Video and Lighting Protocol Adapter Connection Diagram. 2
Connecting the ScreenLogic Video & Lighting Protocol Adapter ............ 3
Installing the ScreenLogic Video & Lighting protocol adapter................. 4
Configuring the System ....................................................................... 5
Configuring the Video Camera(s) for the first time ................................ 6
Using the Video Camera Interface ......................................................... 9
Installing the Lights for the first time ................................................... 10
Using the Lights Interface ................................................................... 13
1
ScreenLogic Video & Lighting Protocol Adapter
Using the SceenLogic Video & Lighting Protocol adapter with your
existing ScreenLogic system you can control up to four color video
cameras to monitor your pool/spa and home areas via your ScreenLogic
interface device or PC at home or remotely over the Internet. Also, using
a Lighting Powerline Interface Module you can control any number of
outside and inside lights.
Features:
Remotely monitor your property via video cameras
Control outside lights (pathway, front door, entry hallway, stairwells,
garage entryway, etc.)
Control lights inside the home
Log on anywhere via your laptop or PC for full control
Compatible with all IntelliTouch systems
Supported Video Cameras and Light Switches
The following video camera models and Powerline Control systems are
supported for use with the ScreenLogic Video & Lighting Protocol adapter:
- Panasonic video camera Models: BL-C1A, BL-C111A, BB-HCM311A,
BB-HCM331A, KX-HCM110A,
BB-HCM381A
- Powerline Control Systems, PulseWorx PCS models:
Powerline Interface Module
(PIM) - Model PIM-R
(Serial Interface)
Wall Switch Dimmer (600W)
Model # WS1D6
Note: Panasonic video cameras are widely available for sale on the Internet
Note: PCS light switches *
are compatible with
incondescent light bulbs
only. Lights with florescent
light bulbs cannot be
used.
Note: (*) PCS light switches are widely available on the Internet. Refer to the
following links: http://www.hometech.com/brains/upb.html#PO-PIMR
http://www.hometech.com/modules/upb.html#PO-WS1D6W
ScreenLogic Video & Lighting Protocol Adapter User’s and Installation Guide
1
234
WAN
1
234
2
ScreenLogic Video and Lighting Protocol Adapter
Connection Diagram
For additional cameras
(max qty. 4) an optional
Network switch is
required.
Camera
Powerline
Interface
Module
Existing ScreenLogic
Protocol Adapter
(Pentair Brick: xx-xx-xx)
ScreenLogic Video
& Lighting Protocol
Adapter
AC Power
adapter
DB9M / RJ45
PCS Light switch(s) found
around the home
LAN
COM 1
ScreenLogic
Wireless
Router
Note: PSC light
switches are
compatible with
incondescent
light bulbs only.
Lights with
florescent light
bulbs cannot be
used.
ScreenLogic Video & Lighting Protocol Adapter User’s and Installation Guide
3
Connecting the ScreenLogic Video & Lighting Protocol
Adapter
The following describes how to connect the Video & Lighting Protocol adapter
to an existing ScreenLogic system.
1. Connect the provided RJ45 (CAT5) cable to an available port (1, 2, 3,
or 4) on the ScreenLogic wireless router. Connect the other end of the
cable to the LAN port on the Video & Lighting Protocol adapter (see
diagram on page 2).
2. Lights cable connection: Connect an RJ45 (CAT5) cable to the
COM 1 port on the adapter. Connect the other end of the cable to the
DB9M/RJ45 adapter. Connect the DB9M/RJ45 adapter to the RS-232
connector that is connected to the UPB Powerline Interface Module
(PIM). See diagram on page 2.
3. Camera cable connection: Connect AC power plug to the video
camera(s). Connect the RJ45 camera cable to port 1, 2, 3, or 4 on the
ScreenLogic wireless router (see diagram on page 2).
If additional cameras are being installed, a Network Switch can be
used to provide available ports. ScreenLogic supports a maximum of
four cameras (see diagram on page 2).
ScreenLogic Video & Lighting Protocol Adapter Name
The Video & Lighting Protocol adapter system name is identified on the
screen as:
Pentair: xx-xx-xx (where xx-xx-xx are the last six (6) digits of the unit’s serial
number which can be found on a sticker on the adapter). The name is
displayed on the ScreenLogic Connect dialog as shown below:
ScreenLogic Video & Lighting
Protocol Adapter name
Pentair Brick
(192.168.2.2.:80) is the
existing ScreenLogic
Protocol Adapter IP address.
Do not configure this
adapter.
Check this box to save the
current login information
Loading...
+ 11 hidden pages