Pelco IPSXM31CBW23-2X, IPSXM31C22-2, IPSXM31C22-7, IPSXM31C22-7X, IPSXM31C22-2X User Manual

...
0 (0)

O P E R A T I O N / P R O G R A M M I N G

ExSiteSeries

Explosionproof

Positioning System

C1300M-B (6/05)

Contents

Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Set the Calibration Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

How to Operate Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7

Accessing Main Menu (Preset 95). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

CM6700/CM6800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

KBD200A/KBD300A (Direct Mode Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

CM9500. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

CM9740/CM9760/CM9770/CM9780. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

KBD4000/KBD4002 (Genex multiplexer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

MPT9500. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

PelcoNet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

Quick Start Guide – System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Unit Inversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Display Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Label Position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Unit Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Type of Lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Auto Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Zoom Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Zoom Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Low Light Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 IR Cut Filter (23X Day/Night Camera). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Advanced Camera Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Shutter Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 AGC Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Auto Iris. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Auto Sharpness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Auto White Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Backlight Compensation (BLC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Video Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Wide Dynamic Range (23X Day/Night Camera). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Proportional Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Park Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Scan Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 preset freeze frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Limit Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Azimuth Zero. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Power Up Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Line Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

C1300M-B (6/05)

3

Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Enable Motion Detection (23X Day/Night Camera) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Edit Detection Areas (23X Day/Night Camera) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Activate AUX Command (23X Day/Night Camera). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

AUX Time (23X Day/Night Camera) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Window Blanking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Clear Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Blank All Above/Blank All Below . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Wiper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Wiper Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Wiper Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Wiper Dwell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Wiper Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Set Washer Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

AUX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Position Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Reset, Cycle Power, Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Reset Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Cycle Camera Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Reboot System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Software/Language File Upload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Upload Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

4

C1300M-B (6/05)

Regulatory Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.

Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications CommissionÕs rules.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

C1300M-B (6/05)

5

Welcome

Thank you for purchasing Pelco’s ExSite™ IPSXM Series explosionproof positioning system. Your new system features a high resolution, camera/optics package with programmable software.

This manual is designed to be a reference tool for the operation and programming of your system. Inside you will find information about the features and commands of your IPSXM system, as well as a detailed menu tree.

MODELS

IPSXM30C22-2 Pan and tilt system with color camera, 60 Hz, 24 VAC

IPSXM30C22-2X Pan and tilt system with color camera, 50 Hz, 24 VAC

IPSXM31C22-2 Same as IPSXM30C22-2, except supplied with window wiper

IPSXM31C22-2X Same as IPSXM30C22-2X, except supplied with window wiper

IPSXM30CBW23-2 Pan and tilt system with day/night camera, 60 Hz, 24 VAC

IPSXM30CBW23-2X Pan and tilt system with day/night camera, 50 Hz, 24 VAC

IPSXM31CBW23-2 Same as IPSXM30CBW23-2, except supplied with window wiper

IPSXM31CBW23-2X Same as IPSXM30CBW23-2X, except supplied with window wiper

IPSXM30C22-7 Pan and tilt system with color camera, 60 Hz, 90-264 VAC

IPSXM30C22-7X Pan and tilt system with color camera, 50 Hz, 90-264 VAC

IPSXM31C22-7 Same as IPSXM30C22-7, except supplied with window wiper

IPSXM31C22-7X Same as IPSXM30C22-7X, except supplied with window wiper

IPSXM30CBW23-7 Pan and tilt system with day/night camera, 60 Hz, 90-264 VAC

IPSXM30CBW23-7X Pan and tilt system with day/night camera, 50 Hz, 90-264 VAC

IPSXM31CBW23-7 Same as IPSXM30CBW23-7, except supplied with window wiper

IPSXM31CBW23-7X Same as IPSXM30CBW23-7X, except supplied with window wiper

GETTING STARTED

You will need to install your system before using this manual. Refer to the installation manuals for instructions. Once installed apply power to the system. The system will begin a configuration sequence that starts with a limited back and forth pan motion (wiggling) for 2.5 minutes. The limited pan motion is a built-in safety feature to warn anyone at the installation site that the unit is on and to avoid contact with the unit during start up. To stop the limited pan motion press Iris Close. The system will continue its configuration sequence. When the system is done, the following information is displayed:

Pelco ExSite IPSXM

Version X.XX

D Address: 1

P Address: 2

Comm 2400, N, 8, 1

CONFIGURE DONE

This information will remain on the monitor until system operation begins. Refer to the following pages to learn how to operate and program your IPSXM Series positioning system.

DANGER: Do not connect the power module to a supply circuit unless all ExSite system components (pan and tilt, camera module and power module) are installed.

SET THE CALIBRATION POINT

Before programming presets, patterns, zones, labels, and window blanking, program and document the position calibration point (refer to Position Calibration). The purpose of the calibration point is to restore all programmed settings quickly in the event the unit is replaced or refurbished.

6

C1300M-B (6/05)

How to Operate Your System

Operation

How to Control

Pan and Tilt

Move joystick or press the direction keys left/right and up/down.

Zoom Far

To zoom far, do the following:

 

1. Press the Zoom Tele button or turn the joystick clockwise until zoom stops at the 32X zoom limit.

 

2. Release the button or joystick for one second.

 

3. To continue zooming (digitally), press the button or turn the joystick clockwise again until you have the picture you

 

want or reach the digital zoom* limit.

Zoom Wide

Press the Zoom Wide button or turn the joystick counterclockwise.

Scanning

 

Stop Scan

Preset 96

Random Scan

Preset 97

Frame Scan

Preset 98

Auto Scan

Preset 99

Presets

Refer to the documentation supplied with the control system.

Patterns**

Refer to the documentation supplied with the control system.

Zones

Refer to the Zones section and to the documentation supplied with the control system.

Alarms

Refer to the Alarms section.

*Digital zoom magnifies the image electronically and the picture may appear pixilated. The larger the digital zoom limit the greater the reduction in resolution.

**The unit cannot do electronic zoom in a pattern. Optical zoom will operate in a pattern.

C1300M-B (6/05)

7

ACCESSING MAIN MENU (PRESET 95)

You can call up the main menu on your monitor by programming (setting or creating) preset 95 (preset 28 if in AD32-preset mode).

Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for programming preset 95 are given below for various Pelco controllers.

CM6700/CM6800

1.Enter the number of the IPSXM system and press the CAM key.

2.Enter 95 and hold the PRESET key for two seconds.

3.In the Edit Preset menu, arrow to SET and press the ACK key. The main menu appears.

KBD200A/KBD300A (DIRECT MODE ONLY)

1.Enter 95.

2.Hold the PRESET key (approximately five seconds) until the main menu appears on the screen.

CM9500

1.Enter the number of the IPSXM system and press the CAM key. The Main menu appears.

2.Highlight SETUP in the Main menu and press the SELECT key.

3.Highlight CAM in the Setup menu and press the SELECT key.

4.Highlight PRESET in the Camera menu and press the SELECT key.

5.Enter 95 and press the F1 key. The main menu appears.

CM9740/CM9760/CM9770/CM9780

1.Press the ESCAPE key to open the Main menu. Select DEF. The Define Submenu appears.

2.Enter your four-digit PIN if this is your first time entering this mode.

3.Enter 95 and select PRST. The main menu appears on the monitor.

4.Select the Quit icon to return to the default menu.

KBD4000/KBD4002 (GENEX MULTIPLEXER)

1.Press the SPOT MONITOR key.

2.Enter the number of the IPSXM system and press the CAM key.

3.Enter 95, then hold the PRESET key (approximately five seconds) until the main menu appears on the screen.

MPT9500

Standard Coaxitron Mode

1.Enter 95 and press the PRESET SET key.

2.Position the asterisk in the YES row and press the F1 key. The main menu appears.

Extended Coaxitron or RS-485 Mode

1.Enter 95 and press the PRESET SET key.

2.Press the F2 key. The main menu appears.

PelcoNet

1.Check the Set box.

2.Click the preset 95 button. The main menu appears.

8

C1300M-B (6/05)

Pelco IPSXM31CBW23-2X, IPSXM31C22-2, IPSXM31C22-7, IPSXM31C22-7X, IPSXM31C22-2X User Manual

Quick Start Guide – System Setup

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PELCO EXSITE IPSXM

 

 

 

 

 

 

 

Quick Programming Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LANGUAGE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UNIT INVERSION

 

 

 

 

 

 

 

 

 

Access the main menu (preset 95). See the Accessing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

<SYSTEM INFORMATION>

 

 

 

 

 

 

 

Main Menu (Preset 95) section.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

<DISPLAY SETUP>

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

<UNIT SETTINGS>

 

 

 

 

 

 

 

 

 

 

 

 

Presets

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

<POSITION CALIBRATION>

 

 

 

 

 

 

 

Use the joystick to position the cursor beside

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The following presets are reserved for special functions.

 

 

 

 

 

 

 

 

 

 

RESET CAMERA

 

 

 

 

 

 

 

 

 

menu selection. If your controller does not have a

 

 

 

 

 

 

 

 

 

 

CYCLE CAMERA POWER

 

 

 

 

 

 

 

joystick, use the up or down key.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Preset

Function

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REBOOT SYSTEM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press Iris Open; the submenu/cursor moves to the right.

33

Flip command (disabled)

 

 

 

 

 

 

 

 

 

 

 

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

86

Wiper

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

87

Washer

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

88

IR filter IN (color)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Move the joystick up or down to view selections.

89

IR filter OUT (black-white)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If your controller does not have a joystick, use the

90-91

Manual limit stops

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

up or down key.

 

 

92-93

Scan limit stops

 

 

 

 

 

ADDITIONAL

SYSTEM INFORMATION

 

DISPLAY SETUP

LABEL POSITION

 

UNIT SETTINGS

 

POSITION CALIBRATION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

95

Select main programming menu

 

 

 

 

 

FREE MEMORY

 

 

UNIT MODEL

 

PRESET LABEL

 

 

[ZONE LABEL- - - - - - - -]

 

<CAMERA>

 

PRESET NOT DEFINED

 

 

 

Press Iris Open to make selection.

96

Stop a scan

 

 

 

 

 

 

LAST RESET

POWER MODULE MEMORY

 

ZONE LABEL

[PRESET LABEL- - - ---]

 

<MOTION>

 

 

 

 

 

 

 

 

 

 

 

 

 

 

<EDIT PRESET SCENE>

 

 

 

 

 

 

 

 

97

Random scanning

 

 

 

 

 

AZIMUTH ZERO OFFSET

SOFTWARE VERSION

 

ZOOM

[ALARM 1- - - - - - -]

 

<POWER UP>

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MOTOR ACTIVE

BIOS VERSION

 

AZMUTH/ELEVATION

 

 

 

<LINE SYNC>

 

 

 

 

 

 

 

 

 

 

98

Frame scanning

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAMERA ACTIVE

FONT VERSION

 

DIRECTION

SAVE AND EXIT

 

<PRESETS>

 

<CLEAR CALIBRATION PRESET>

 

 

 

 

 

 

 

 

99

Start auto scanning

 

 

 

 

 

FPGA VERSION

 

 

 

ALARM MESSAGE

CANCEL AND EXIT

 

<PATTERNS>

 

<RECAL USING CAL PRESET>

 

 

 

Press Iris Close to cancel selection.

 

 

 

 

 

 

 

 

 

VIDEO LEVEL

COMM

 

 

 

 

 

HELP

 

<ZONES>

 

 

 

 

 

NOTE: For American Dynamics controllers with only 32 presets, switch SW3-1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAMERA

D ADDRESS

 

<LABEL POSITION>

 

 

 

<WINDOW BLANKING>

 

BACK

 

 

 

 

 

 

 

 

on the dome drive to the ON position. When SW3-1 is ON, preset

 

 

<EAB>

P ADDRESS

 

RESTORE FACTORY DEFAULTS

XXX/-XXX

 

<ALARMS>

 

EXIT

 

 

 

 

 

 

 

 

99 becomes 32

92 becomes 25

 

 

 

 

 

<PMAB>

CM9500 MODE

 

BACK

NE

 

<WIPER>

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LANGUAGE 1

32 PRESET MODE

 

XXX.XXX

 

<AUX>

 

REFERENCE INFORMATION

 

 

 

 

 

 

 

 

98 becomes 31

91 becomes 24

 

 

 

 

 

PROTOCOL

 

EXIT

 

 

 

<CLEAR>

 

AZIMUTH

 

 

 

 

 

 

 

 

97 becomes 30

90 becomes 23

 

 

 

 

 

LANGUAGE 2

 

 

 

 

 

 

 

 

 

 

<PASSWORD>

 

ELEVATION

 

 

 

 

 

 

 

 

 

 

 

 

 

LANGUAGE 3

<ADDITIONAL>

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

96 becomes 29

89 becomes 22

 

 

 

 

 

LANGUAGE 4

 

 

 

 

 

 

 

 

BACK

 

ZOOM

 

 

 

 

 

 

 

 

95 becomes 28

88 becomes 21

 

 

 

 

 

LANGUAGE 5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LANGUAGE 6

BACK

 

 

 

 

 

 

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

93 becomes 26

 

 

 

 

 

 

BACK

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If the limit stops are turned off, presets 23-26 can be used as regular presets.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAMERA

 

 

MOTION

 

POWER UP

 

LYNE SYNC

 

PRESETS

 

 

PATTERNS

 

 

ZONES

 

 

WINDOW BLANKING

 

ALARMS

 

WIPER**

 

AUX

 

CLEAR

 

PASSWORD

 

TYPE OF LIGHTING

 

 

PROPORTIONAL PAN

 

POWER UP ACTION

 

LINE SYNC

 

PRESET NUMBER

 

PATTERN NUMBER

 

 

ZONE NUMBER

 

 

STYLE

 

RESUME

 

WIPER CONTROL

 

AUX 1 MODE

 

CLEAR ALL ZONES

 

ENABLE PASSWORD

 

AUTO FOCUS

 

 

PARK TIME (MINUTES)

 

 

 

LINE SYNC PHASE

PRESET NOT DEFINED

<PROGRAM PATTERN>

 

ZONE NOT DEFINED

BLANK ALL ABOVE

 

SEQUENCE (SECS)

 

WIPER MODE

 

DWELL TIME (SECS)

 

CLEAR ALL PRESETS

 

<EDIT PASSWORD>

ZOOM LIMIT

 

 

PARK ACTION

 

BACK

 

 

<CLEAR PATTERN>

 

 

 

 

 

 

RESET DELAY (SECS)

 

WIPER DWELL (SECS)

 

 

 

CLEAR ALL PATTERNS

 

 

 

 

ZOOM SPEED

 

 

SCAN SPEED (DEG/S)

 

EXIT

BACK

<EDIT PRESET LABEL>

 

 

 

<EDIT ZONE LABEL>

BLANK ALL BELOW

 

 

 

WIPER TIME (MIN)

 

AUX 2 MODE

 

CLEAR ALL WINDOW BLANKING

 

BACK

 

 

LOW LIGHT LEVEL

 

 

PRESET FREEZE FRAME

 

 

 

EXIT

BACK

 

 

 

 

 

 

 

 

<ALARM SETTINGS>

 

 

 

DWELL TIME (SECS)

 

 

 

EXIT

 

 

IR CUT FILTER*

 

 

LIMIT STOPS

 

 

 

 

 

<EDIT PRESET SCENE>

EXIT

 

<EDIT ZONE>

<SET WINDOWS>

 

 

 

<SET WASHER SEQUENCE>

 

 

 

RESTORE FACTORY DEFAULTS

 

 

 

 

AUTO IR LEVEL*

 

 

<SET MANUAL STOPS>

 

 

 

 

 

<EDIT CAMERA SETTINGS>

 

 

 

ZONE ENABLED

BACK

 

BACK

 

 

 

BACK

 

 

 

 

 

 

 

 

 

<CLEAR MANUAL STOPS>

 

 

 

 

 

<MOTION DETECTION>*

REFERENCE INFORMATION

 

ZONE BLANKING

 

EXIT

 

BACK

 

EXIT

 

BACK

 

 

 

 

<ADVANCED SETTINGS>

<SET SCAN STOPS>

 

 

 

 

 

<CLEAR PRESETS>

PATTERN USAGE

 

 

 

 

 

EXIT

 

 

 

EXIT

 

 

 

EXIT

 

 

 

 

 

 

 

<CLEAR SCAN STOPS>

 

 

 

 

 

REMAINING

 

<CLEAR ZONE>

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BACK

 

 

<SET AZIMUTH ZERO>

 

 

 

 

 

<CLEAR CAMERA SETTINGS>

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXIT

 

 

<CLEAR AZIMUTH ZERO>

 

 

 

 

 

BACK

 

 

 

BACK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BACK

 

 

 

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ADVANCED SETTINGS

 

 

 

 

 

 

MOTION DETECTION*

 

 

 

 

 

 

 

SET WINDOWS

 

ALARM SETTINGS

 

SET WASHER SEQUENCE

 

 

 

 

 

 

 

 

SHUTTER SPEED

 

 

 

 

 

 

 

 

MOTION DETECTION ENABLED

 

 

 

 

 

 

 

 

WINDOW NUMBER

 

ALARM NUMBER

 

PRESET NOT DEFINED

 

 

 

 

 

EDIT THE PASSWORD

AGC LIMIT

 

 

 

 

 

 

 

 

<EDIT DETECTION AREA>

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

- - - - - - - - - - - - - - - - -

 

AUTO IRIS

 

 

 

 

 

 

 

 

ACTIVATE AUX

 

 

 

 

 

 

 

<EDIT WINDOW LOCATION>

 

ALARM PRIORITY

 

<EDIT PRESET LABEL>

 

 

 

 

1234567890

OK

AUTO IRIS LEVEL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

<EDIT WINDOW ZOOM>

 

ALARM ACTION

 

<EDIT PRESET SCENE>

 

 

 

 

 

ABCDEFGHIJ

CANCEL

AUTO IRIS PEAK

 

 

 

 

 

 

 

 

AUX TIME

 

 

 

 

 

 

 

 

 

 

ACTIVATE AUX

 

<EDIT CAMERA SETTINGS>

 

 

 

 

 

KLMNOPQRST

 

 

AUTO SHARPNESS

 

 

 

 

 

 

BACK

 

 

 

 

 

 

 

ENABLE WINDOW

 

ALARM CONTACT

 

 

 

 

 

 

 

UZWXYZ.,-/

SPACE

SHARPNESS LEVEL

 

 

 

 

 

 

 

 

 

 

 

 

 

REVERSE

 

 

 

WASHER TIME (SECS)

 

 

 

 

 

abcdefghij

BACKSPACE

AUTO WHITE BALANCE

 

 

 

 

 

 

EXIT

 

 

 

 

 

 

 

CLEAR WINDOW

 

BACK

 

WIPER DELAY (SECS)

 

 

 

 

 

klmnopqrst

 

 

R GAIN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BACK

 

EXIT

 

AUTO RETURN

 

 

 

 

 

uvwxyz*;:

 

 

B GAIN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

<CLEAR PRESET>

 

 

 

 

 

 

 

 

BACKLIGHT COMP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

VIDEO LEVEL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

<CLEAR CAMERA SETTINGS>

 

 

 

 

 

 

 

 

WIDE DYNAMIC RANGE*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BACK

 

 

 

 

 

 

 

 

BACK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EDIT DETECTION AREA*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DETECTION AREA 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LOCATION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SENSITIVITY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DETECTION AREA 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LOCATION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SENSITIVITY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DETECTION AREA 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LOCATION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SENSITIVITY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DETECTION AREA 4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LOCATION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SENSITIVITY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

* Available only with the 23X day/night camera.

 

 

 

 

 

BACK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

** Available only with wiper models.

 

 

 

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C1300M-B (6/05)

9

10

C1300M-B (6/05)

Language

PELCO EXSITE IPSXM

LANGUAGE

ENGLISH

UNIT INVERSION

OFF

<SYSTEM INFORMATION>

 

<DISPLAY SETUP>

 

<UNIT SETTINGS>

 

<POSITION CALIBRATION>

 

RESET CAMERA

 

CYCLE CAMERA POWER

 

REBOOT SYSTEM

 

EXIT

 

The language for the on-screen menus is selectable. Available languages include English, Spanish, French, German, Italian, Portuguese, Polish, Russian, Turkish, and Czechoslovakian. The factory default language is English.

To change the display language:

1.Use the joystick to position the cursor beside LANGUAGE.

2.Press Iris Open. The cursor moves to the right, beside the current, selected language.

3.Move the joystick up or down to view selections. Press Iris Open to enter selection. All on-screen menus are changed to the selected language.

Quick Programming Guide

(See Page 9)

C1300M-B (6/05)

11

Unit Inversion

PELCO EXSITE IPSXM

LANGUAGE

ENGLISH

UNIT INVERSION

OFF

Unit inversion reconfigures the system so that it operates normally when it is installed in an inverted postion. The following are the available settings for unit inversion.

<SYSTEM INFORMATION> <DISPLAY SETUP>

<UNIT SETTINGS> <POSITION CALIBRATION>

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT

OFF (default)

Use for normal installations (refer to Figure 1).

ON

Reconfigures the camera oriention and controller functions for inverted

 

operation when the unit is installed in an inverted position (refer to Figure 1).

 

 

 

 

 

 

 

 

 

 

 

 

STANDARD

INVERTED

INSTALLATION

INSTALLATION

Figure 1. Installation Methods

To reconfigure the unit for inverted operation and control:

1.Use the joystick to position the cursor beside UNIT INVERSION.

2.Press Iris Open. The cursor moves to the right.

3.Move the joystick up or down to view selections. Press Iris Open to enter selection. The system will start a configuration sequence. When configuration is completed, the camera will be oriented in the correct position for the installation.

12

C1300M-B (6/05)

System Information

PELCO EXSITE IPSXM

LANGUAGE

ENGLISH

UNIT INVERSION

OFF

 

 

<SYSTEM INFORMATION>

 

<DISPLAY SETUP>

 

<UNIT SETTINGS>

 

<POSITION CALIBRATION>

 

RESET CAMERA

 

CYCLE CAMERA POWER

 

REBOOT SYSTEM

 

EXIT

 

SYSTEM INFORMATION

UNIT MODEL

1PSXM31CBW

POWER MODULE MEMORY

AVAILABLE

SOFTWARE VERSION

0.90.9013

BIOS VERSION

8.00.9000

FONT VERSION

1.00

COMM

2400,N,8,1

D ADDRESS

1

P ADDRESS

2

CM9500 MODE

OFF

32 PRESETS

OFF

PROTOCOL

D

<ADDITIONAL>

 

BACK

 

EXIT

 

 

 

 

 

ADDITIONAL

 

 

FREE MEMORY

30464

LAST RESET

3

AZIMUTH ZERO OFFSET

0.00°

MOTOR ACTIVE

YES

CAMERA ACTIVE

YES

FPGA VERSION

2

VIDEO LEVEL

HIGH

CAMERA

XXXX-XXXX

<EAB>*

 

<PMAB>**

 

LANGUAGE 1

ENGLISH 1.00

LANGUAGE 2

ESPANOL 1.00

LANGUAGE 3

ITALIANO 1.00

LANGUAGE 4

DEUTSCH 1.00

LANGUAGE 5

PORTUGUES 1.00

LANGUAGE 6

FRANCAIS 1.00

LANGUAGE 7

CESKY 1.00

LANGUAGE 8

POLSKI 1.00

LANGUAGE 9

RUSSIAN 1.00

LANGUAGE 10

TURKISH 1.00

BACK

EXIT

The system Information screen displays ExSite model, software version, available memory, and other diagnostic information.

System settings cannot be changed using this screen. This screen is for reference only.

Use the following steps to display the System Information screen:

1.Use the joystick to position the cursor beside SYSTEM INFORMATION.

2.Press Iris Open. The SYSTEM INFORMATION window opens.

*EAB (Enclosure Accessory Board): The EAB information screen displays availability, version, and part number of the enclosure accessory board

**PMAB (Power Module Accessory Board): The PMAB information screen displays availability, version, and part number of the power module accessory board.

Quick Programming Guide

(See Page 9)

C1300M-B (6/05)

13

Display Setup

PELCO EXSITE IPSXM

LANGUAGE

ENGLISH

UNIT INVERSION

OFF

<SYSTEM INFORMATION>

 

<DISPLAY SETUP>

 

<UNIT SETTINGS>

 

<POSITION CALIBRATION>

 

RESET CAMERA

 

CYCLE CAMERA POWER

 

REBOOT SYSTEM

 

EXIT

 

 

 

 

 

 

 

DISPLAY SETUP

 

 

 

 

 

 

 

PRESET LABEL

2 (SECS)

ZONE LABEL

2 (SECS)

ZOOM

2 (SECS)

AZIMUTH/ELEVATION

2 (SECS)

DIRECTION

OFF

ALARM MESSAGE

2 (SECS)

<LABEL POSITIONS>

 

RESTORE FACTORY DEFAULTS

 

BACK

 

EXIT

 

Display setup allows you to program how labels are displayed on the monitor. The following labels are available:

PRESET LABEL

Identifies preset.

ZONE LABEL

Identifies zone.

ZOOM

Identifies the amount of magnification.

AZIMUTH*/

Amount of pan from 0° and the amount of tilt from 0° horizontal.

ELEVATION**

 

DIRECTION

Displays compass direction.

ALARM MESSAGE

Displays activated alarm.

A preset label is displayed when a preset is called. A zone label is displayed when the system moves into a zone. The zoom ratio label is displayed when zoom is activated. Azimuth/elevation and direction labels are displayed when pan/tilt is activated. An alarm message appears on the monitor when an alarm occurs.

The following settings are available for each label:

OFF

Label is not displayed when activated.

CONSTANT

The label is continually displayed when activated.

2 SECONDS

The label is displayed for 2 seconds after activation.

5 SECONDS

The label is displayed for 5 seconds after activation.

10 SECONDS

The label is displayed for 10 seconds after activation.

*Azimuth is the pan angle from 0 to 359 degrees.

**Elevation is the tilt position from +90 (horizon) to -90 degrees.

14

C1300M-B (6/05)

LABEL POSITIONS

PELCO EXSITE IPSXM

LANGUAGE

ENGLISH

UNIT INVERSION

OFF

<SYSTEM INFORMATION> <DISPLAY SETUP>

<UNIT SETTINGS> <POSITION CALIBRATION>

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

DISPLAY SETUP

PRESET LABEL

2 (SECS)

ZONE LABEL

2 (SECS)

ZOOM

2 (SECS)

AZIMUTH/ELEVATION

2 (SECS)

DIRECTION

OFF

ALARM MESSAGE

2 (SECS)

<LABEL POSITIONS> RESTORE FACTORY DEFAULTS

BACK

EXIT

[ZONE LABEL ------------

]

[PRESET LABEL ------------

]

[ALARM 1 ------------

]

SAVE AND EXIT

CANCEL AND EXIT

HELP

XXX°/-XX° XXX.XX

Labels can be placed anywhere on the monitor. This feature allows you to customize the appearance of your monitor screen.

The following labels are not set at fixed positions:

Preset Label

Zone Label

Alarm 1

Azimuth*/Elevation**: XXX°/-XX°

Zoom Ratio: XXX.XX

Direction: Compass direction is shown.

To set a label position:

1.Use the joystick to position the cursor beside a label.

2.Press Iris Open.

3.Use the joystick to move the label up, down, left, and/or right.

4.Press Iris Open.

5.Repeat steps 1 through 4 to position other labels.

6.Position the cursor next to Save and Exit. Press Iris Open to save settings and exit menu.

*Azimuth is the pan angle from 0 to 359 degrees.

**Elevation is the tilt position from +90 (horizon) to -90 degrees.

Quick Programming Guide

(See Page 9)

C1300M-B (6/05)

15

Loading...
+ 33 hidden pages