Peerless-AV PTM200-S Installation

Installation and Assembly:
A
Rotational Mount Interface
Models: RMI1
Before you begin, make sure all parts shown are included with your product. Parts may appear slightly different than illustrated.
Parts List
Description Qty. Part #
universal rotational mount 1 120-1183 M10 x 15 mm round socket head screw 8 520-9262
B
M6 x 10 mm socket pin head screw 4 520-1066
C
multi-washer 4 580-1036
D
4 mm security allen wrench 1 560-1727
E
6 mm allen wrench 1 560-9716
F
F
Accessories
ACC170 - Rotational Mount Adapter Plate
for Carts and S tands
B C DA
E
1 of 4
Visit the Peerless Web Site at www.peerlessmounts.com
For customer care call 1-800-865-2112 or 708-865-8870.
ISSUED: 06-16-08 SHEET #: 120-9049-1
Attaching Rotational Mount to PLP Model Adapter Plate
NOTE: Dedicated PLP model adapter plate not included. For screen compatibility please call customer care to
purchase a dedicated PLP adapter plate. If necessary , disengage T -handle from sprocket
1
plate of rotational mount (A) and rotate sprocket so largest hole pattern aligns with clearance holes of sprocket.
Align inner most M10 hole set and fasten rotational mount assembly (A) to PLP adapter plate with four M10 x 15 mm screws (B) as shown. Tighten all fasteners with 6 mm allen wrench (F).
NOTE: Be sure outer flange of PLP adapter plate face away from rotational mount.
NOTE: Skip step 2 if dedicated PLP adapter plate is already attached to screen.
T-HANDLE
FLANGE
B
A
DEDICATED PLP ADAPTER PLATE
Place PLP adapter plate on back of screen,
2
align to holes, and center on back of screen. Secure PLP adapter plate to back of screen using fasteners provided with PLP adapter plate.
DEDICATED PLP ADAPTER PLATE
Visit the Peerless Web Site at www.peerlessmounts.com
2 of 4
ISSUED: 06-16-08 SHEET #: 120-9049-1
For customer care call 1-800-865-2112 or 708-865-8870.
Installing Wall Mount Hook Bracket Installing Ceiling Mount Tilt Bracket
3- 1
BRACKET
Attach hook bracket to rotational mount (A) using the M10 x 15 mm screws provided with hook bracket as shown below.
M10 X 15 mm screws
HOOK
3- 2
Attach tilt bracket to rotational mount (A) using the M10 x 15 mm screws provided with tilt bracket as shown below.
M10 X 15 mm screws
TILT
BRACKET
A
A
NOTE: Reinstall hook bracket to wall mount according to wall mount
instructions.
NOTE: Reinstall tilt bracket to ceiling mount according to ceiling mount instructions.
Installing Stand Adapter Bracket Installing SR Cart and SS Stand
Attach adapter bracket to rotational mount (A) using the
3- 3
M10 x 15 mm screws provided with adapter bracket as shown below.
ADAPTER BRACKET
M10 x 15 mm screws
Hook Plate
3- 4
NOTE: The ACC170 (sold separately) accessory is required.
Align inner holes of accessory plate to inner holes of hook plate. Attach accessory plate to hook plate using four M10 x 15 mm screws (B) with 6 mm allen wrench (F) as shown below.
HOOK PLATE
ACCESSORY PLATE
B
A
Attach interface plate to rotational mount (A) using the M10 x 15 mm screws provided with hook plate as shown below.
M10 x 15 mm screws
INTERFACE PLATE
A
NOTE: Reinstall adapter bracket to LCD stand according to stand
instructions.
Visit the Peerless Web Site at www.peerlessmounts.com
NOTE: Reinstall hook plate to cart or stand according to instructions included with cart or stand
3 of 4
For customer care call 1-800-865-2112 or 708-865-8870.
ISSUED: 06-16-08 SHEET #: 120-9049-1
Adjustment of Orientation
WARNING
• It may be necessary to disconnect cables before rotating into extreme angles. Failure to do so may result in property damage or serious injury .
• Always use an assistant or mechanical lifting equipment to safely lift, position, and align equipment.
Pull T -handle to release sprocket as shown in figure 4.1,
4
allowing rotation of screen to desired viewing angle as shown in figure 4.2. Release T -handle and engage with sprocket to restrict rotation of screen.
T-HANDLE
SECURITY
SCREW
fig. 4.1
OPTIONAL: T o prevent screen rotation, fully
5
tighten security screw against T -handle flange as shown in detail 1.
SECURITY SCREW
T-HANDLE
T o rotate screen, disengage security screw from T-handle flange using 4 mm security allen wrench (E) until screw tip is flush with access window as shown in detail 2 and follow step 4.
T-HANDLE
FLANGE
DETAIL 1
fig. 4.2
Visit the Peerless Web Site at www.peerlessmounts.com
SECURITY SCREW
T-HANDLE
4 of 4
ACCESS
WINDOW
DETAIL 2
ISSUED: 06-16-08 SHEET #: 120-9049-1
For customer care call 1-800-865-2112 or 708-865-8870.
Loading...