Peerless Industries PWV240-BK, PP740 User Manual

Features:

• Fits 22" - 40" (56 - 102 cm) LCD screens

• Two tensionable pivot points for extensive adjustment of

viewing angle

• VESA

75/100/200 x 100/200 x 200 compatible

• Frees up space by folding ﬂat against the wall

Installation and Assembly:

Paramount™ Pivot for 22" - 40" (56 - 102 cm) LCD screens

Models: PP740, PWV240/BK

Max Load Capacity: 80lb (36 kg)

USC

ISSUED: 02-05-09 SHEET #: 202-9312-1

2 of 20

ISSUED: 02-05-09 SHEET #: 202-9312-1

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

• Wood Beam Included

• Solid Concrete Included

• Cinder Block Included

• Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit - WSP490;

• Brick Contact Qualiﬁed Professional

• Other or unsure? Contact Qualiﬁed Professional

WARNING

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Wood Stud Wall ................................................................................................................................................4

Installation to Solid Concrete and Cinder Block .....................................................................................................................5

Attaching Adapter Plate to Screen with VESA

Mounting Pattern ..........................................................................................6

Installing to Peerless LC or PLP Model Adapter Bracket .......................................................................................................8

Cord Management and Arm Tension Adjustment ................................................................................................................10

NOTE: Read entire instruction sheet before you start installation and assembly.

Tools Needed for Assembly

• stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• phillips screwdriver

• drill

• 5/16" (8 mm) bit for concrete and cinder block wall

• 5/32" (4 mm) bit for wood stud wall

• level

3 of 20

ISSUED: 02-05-09 SHEET #: 202-9312-1

Parts may appear slightly different than illustrated.

Before you begin, make sure all parts shown are included with your product.

PWV240/B

PP740

Description

Part #

wall mount assembly

095-0545-GB

concrete anchor 2 590-0320

retaining spacer 4 590-5005

1/4-20 x 13 mm flat head phillips screw 2 520-1209

M4 x 10 mm phillips screw 4 504-9012

M4 x 20 mm phillips screw 4 504-9020

M6 x 12 mm phillips screw 4 520-1128

#14 x 63.5 mm flat head wood screw 2 520-1202

M6 x 20 mm phillips screw 4 520-9402

M6 x 30 mm phillips screw 4 510-9109

M5 x 6 mm phillips screw 5 520-1023

#10 flat washer 4 540-9400

hook bracket 1

095-P1346

adapter plate

095-P1322

#10-32 x 6 mm flat head phillips screw 1 520-1108

P cable tie 1 560-1725

Parts List

4 of 20

ISSUED: 02-05-09 SHEET #: 202-9312-1

Installation to Wood Stud Wall

Using a stud ﬁnder, locate and mark the edges of the wood stud used in mounting this product. Use of an edge to

edge stud ﬁnder is highly recommended. Use a level to draw a vertical line down the center of the stud. Use wall

plate as template to mark center of holes along the vertical line. Drill two 5/32" (4 mm) dia. holes 2.5" (64 mm)

deep. Attach wall mount (A) to wall using two #14 x 63.5 mm ﬂat head wood screws (H) as shown.

Skip to step 2 on page 6.

WOOD STUD WALL

WALL PLATE

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-

ers are responsible to provide hardware for other types of mounting situations (not UL approved).

WARNING

5 of 20

ISSUED: 02-05-09 SHEET #: 202-9312-1

Installation to Solid Concrete and Cinder Block

Level and use wall plate as template to mark center

of holes.

Drill two 5/16" (8 mm) dia. holes to a

minimum depth of 2.5" (64 mm). Insert anchors (B)

in holes ﬂush with wall. Place wall mount (A) over

anchors and secure with wood screws (H). Make

sure wall mount is level, and tighten all fasteners.

WALL PLATE

SOLID CONCRETE

CINDER BLOCK

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

dry wall

plaster/

dry wall

concrete

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a

solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90

speciﬁcations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

WARNING

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

the screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to

concrete covered with plaster, drywall, or other

ﬁnishing material. If mounting to concrete surfaces

covered with a ﬁnishing surface is unavoidable,

the ﬁnishing surface must be counterbored as

shown below. Be sure concrete anchors do not

pull away from concrete when tightening screws. If

plaster/drywall is thicker than 5/8" (16 mm), custom

fasteners must be supplied by installer.

WARNING

Drill holes and insert anchors (B).

Place plate (A) over anchors (B) and secure with screws (H).

Tighten all fasteners.

concrete

surface

6 of 20

ISSUED: 02-05-09 SHEET #: 202-9312-1

Attaching Adapter Plate to Screen with VESA

200 x 100

or 200 x 200 Mounting Pattern

Attach hook bracket (M) to adapter plate (N) using

four M5 x 6 mm screws (K) and #10 washers (L) as

shown.

FOR VESA

200 x 100 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach

adapter plate (N) to back of screen using four M4 x

10 mm screws (E) as shown below.

*NOTE: If screw (E) gets less than three threads

of engagement, attach adapter plate (N) to back of

screen using four M4 x 20 mm screws (F) and four

spacers (C) as indicated below.

Skip to step 3 on page 9.

FOR VESA

200 x 200 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach adapter

plate (N) to back of screen using four M6 x 12 mm

screws (G) as shown below.

*NOTE: If screw (G) gets less than three threads

of engagement, attach adapter plate (N) to back of

screen using four M6 x 20 mm screws (I). If screw (I)

still gets less than three threads of engagement, use

four M6 x 30 mm screws (J).

Skip to step 3 on page 9.

NOTE: For VESA 75 mm and 100 mm patterns, see following page.

2-1

• If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not

tightly secured, damage may occur to screen or product may fail.

WARNING

*For screens with a

hole pattern in a pocket,

spacers (C) go between

adapter plate (N) and

screen.

+ 14 hidden pages