Peerless Industries SWS510-BK, SF670P-S, SF670-S, SWS510-SI, SF680P-S User Manual

...
0 (0)

Installation and Assembly:

SmartMount® Universal Flat Wall Mount for LCD and Plasma Flat Panel Plasma Screens

Model #

Screen Size Range

Max. UL Load Capacity

 

U

SF670, SF670-S, SF670P, SF670P-S

 

 

C

SWS510/BK, SWS510/SI

42''- 71'' (107 - 180 cm)

250 lb (113kg)

© L US

 

 

 

 

 

SF680*, SF680-S*, SF680P*, SF680P-S*

61''- 102'' (155 - 259 cm)

350 lb (159kg)

 

 

*not evaluated by GS

I D :00

0

 

2

76

0018

 

(SF670)

(SF680)

Features:

Colors: silver or black

Slim design holds screen close up against the wall

Screen simply hooks onto the wall plate for quick and easy installation

Optional horizontal adjustment of up to 12" (305 mm) (depending on screen model)

Includes hardware for installation to wood studs, concrete and cinder block

Theft-resistant security screws

ISSUED: 11-09-07 SHEET #: 202-9253-4 08-31-10

NOTE: Read entire instruction sheet before you start installation and assembly.

WARNING

Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.

This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.

Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

Never exceed the Maximum Load Capacity. See page one.

If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an "edge to edge" stud finder is highly recommended.

Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.

This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.

This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION

HARDWARE REQUIRED

Wood Stud

Included

Wood Beam

Included

Solid Concrete

Included

Cinder Block

Included

Metal Stud

Do not attach except with Peerless Metal Stud Accessory Kit - ACC615;

 

 

(not evaluated by UL)

Brick

Contact Qualified Professional (not evaluated by UL)

Other or unsure?

Contact Qualified Professional

Tools Needed for Assembly

stud finder ("edge to edge" stud finder is recommended)

phillips screwdriver

drill

5/16" (8 mm) bit for concrete and cinder block wall

5/32" (4 mm) bit for wood stud wall

level

Table of Contents

 

Parts List.................................................................................................................................................................................

3

Installation to Triple Wood Stud Wall......................................................................................................................................

4

Installation to Solid Concrete or Cinder Block ........................................................................................................................

5

Installing Adapter Brackets.....................................................................................................................................................

6

Installing Flat Panel Screen to Wall Plate...............................................................................................................................

8

2 of 34

ISSUED: 11-09-07 SHEET #: 202-9253-4 08-31-10

SF670,SF670-S, SF670P,SF670P-S, SWS510/BK, SWS510/SI

SF680SF680,-S, SF680P,SF680P-S

 

Before you begin, make sure all parts shown are included with your product. Parts may appear slightly

 

Description

 

Qty.

Part Number

Part Number

Part Number

Part Number

 

 

 

different than illustrated.

 

 

 

 

 

 

 

 

Parts List

 

 

 

 

SWS510/BK

SWS510/SI

 

 

 

 

 

 

SF680

SF680-S

SF680P

SF680P-S

 

 

 

 

 

 

SF670

SF670-S

SF670P

SF670P-S

X

 

AA wall plate

 

1

200-1901

200-4901

200-1901

200-4901

 

X

 

 

 

 

200-1902

200-4902

200-1902

200-4902

X

 

BB adapter bracket

 

2

200-0942

200-0943

200-0940

200-0941

 

X

 

 

 

 

200-0946

200-0947

200-0944

200-0945

X

X

CC #14 x 2.5" wood screw

 

6

5S1-015-C03

5S1-015-C03

5S1-015-C03

5S1-015-C03

X

X

DD concrete anchor

 

6

590-0320

590-0320

590-0320

590-0320

X

X

EE 4 mm allen wrench

 

1

560-1727

560-1727

560-1727

560-1727

 

X

GG 0 [ PP VFUHZ

 

4

520-1305

520-1305

520-1305

520-1305

 

X

HH washer

 

6

5W1-035-X01

5W1-035-X01

5W1-035-X01

5W1-035-X01

 

AA

BB

 

 

CC

 

 

 

 

 

 

 

 

 

 

 

 

 

GG

or

 

 

DD

 

 

 

 

 

 

 

 

 

 

 

HH

 

 

 

 

 

 

 

 

 

 

 

 

EE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Adapter Bracket Fasteners

 

 

M4 x 12 mm (6)

M5 x 12 mm (4)

 

 

 

(504-9013)

(520-1027)

M6 x 12 mm (4)

 

 

 

 

 

 

M4 x 25 mm (4)

M5 x 25 mm (4)

(520-1128)

M6 x 20 mm (4)

 

(504-1015)

(520-9543)

 

M6 x 30 mm (4)

 

 

 

(520-9402)

(510-9109)

 

 

 

 

.5" spacer (4)

(540-1057)

M6 x 25 mm (4) (520-1208)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

multi-washer (6)

M8 x 25 mm (4)

 

 

 

 

M8 x 40 mm (4)

(580-1036)

(520-1031)

.75" spacer (4)

M8 x 16 mm (6)

(540-1059)

(520-9257)

(520-1136)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 of 34

 

 

ISSUED: 11-09-07 SHEET #: 202-9253-4 08-31-10

Installation to Triple Wood Stud Wall

WARNING

Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.

Never tighten in excess of 80 in. • lb (9 N.M.).

Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended.

Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

1

Wall plate (AA) can be mounted to three studs that are 16" (41 cm) apart. Use a stud finder to locate the edges

of the studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical

line down each stud’s center. Place wall plate on wall as a template. The top mounting slots should be located "X" distance above the desired screen center as shown in figure 1.1 and chart 1. Level plate, and mark the center of the six mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill six 5/32" (4 mm) dia. holes 2.5" (64 mm) deep. Make sure that the wall plate is level, secure it using six #14 x 2.5" wood screws (CC) as shown in figure 1.2.

Skip to step 2.

NOTE: Wall plate may be mounted up to 6" (152 mm) off center as shown in figure 1.1.

STUD

6"

6"

 

(152 mm)

(152 mm)

AA

CS "X"

CS = center of screen

fig. 1.1

"X" Distance

 

SF670 and SWS510 models

.75"

(19 mm)

 

SF680 models

3.75"

(95 mm)

AA

CC

fig. 1.2

4 of 34

ISSUED: 11-09-07 SHEET #: 202-9253-4 08-31-10

Installation to Solid Concrete or Cinder Block

WARNING

When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware and components.

1

Make sure that wall plate (AA) is level, use it as a

template to mark six mounting holes. The top mounting

slots should be located above the desired screen center as indicated by dimension X in figure 1.1 and charts on pages 4. Drill six 5/16" (8 mm) dia. holes to a minimum depth of 2.5" (64 mm). Insert anchors (DD) in holes flush with wall as shown (right). Place wall plate over anchors and secure with #14 x 2.5" screws (CC). Level, then tighten all fasteners.

WARNING

Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power.

Never tighten in excess of 80 in. • lb (9 N.M.).

Always attach concrete expansion anchors directly to load-bearing concrete.

Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable (not evaluated by UL), the finishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8" (16 mm), custom fasteners must be supplied by installer (not evaluated by UL).

VIEW

 

INCORRECT

CORRECT

wall

concrete

wall

concrete

 

 

 

plate

 

 

plate

 

 

CUTAWAY

 

 

 

 

drywall

 

drywall

 

 

plaster/

 

plaster/

1

concrete

surface

DD

Drill holes and insert anchors (DD).

2

AA

 

 

CC

DD

Place plate (AA) over anchors (DD) and secure with screws (CC).

3

Tighten all fasteners.

SOLID CONCRETE

DD

CINDER BLOCK

AA

CC

5 of 34

ISSUED: 11-09-07 SHEET #: 202-9253-4 08-31-10

Installing Adapter Brackets

WARNING

Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.

2

To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen.

Place screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be

attached. Place adapter brackets (BB) on back of screen, align to holes, and center on back of screen as shown below. Attach the adapter brackets to the back of the screen using the appropriate combination of screws, multi-washers, and spacers as shown in figure 2.1 or 2.2

NOTE: Top and bottom holes must always be used.

Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.

X

BB

CENTER BRACKETS VERTICALLY

ON BACK OF SCREEN

X

NOTE: "X" dimensions should be equal.

MULTI-WASHER

MEDIUM HOLE FOR M5 SCREWS

SMALL HOLE FOR M4 SCREWS

LARGE HOLE FOR M6 SCREWS

Notes:

The number of fasteners used will vary, depending upon the type of screen.

Multi-washers and spacers may not be used, depending upon the type of screen.

Use the corresponding hole in the multiwasher that matches your screw size as shown.

Slots in SF680 models are wider and require the use of the M8 washer.

NOTE: For flat back screens proceed to step 2-1. For bump-out or recessed back screen skip to step 2-2.

6 of 34

ISSUED: 11-09-07 SHEET #: 202-9253-4 08-31-10

For Flat Back Screen

2-1 Begin with the shortest length screw, hand thread through multi-washer and adapter bracket (BB) into screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.

NOTE: Spacers may not be used, depending upon the type of screen.

fig 2.1

SCREEN

MULTI-WASHER

SCREW

ADAPTER BRACKET (BB)

If you have any questions, please call Peerless customer care at 1-800-865-2112.

For Bump-out or Recessed Back Screen

2-2 Begin with longer length screw, hand thread through multi-washer, adapter bracket (BB) and spacer in that order into screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.

SCREEN

fig 2.2

MULTI-WASHER

SPACER

SCREW

ADAPTER BRACKET (BB)

If you have any questions, please call Peerless customer care at 1-800-865-2112.

7 of 34

ISSUED: 11-09-07 SHEET #: 202-9253-4 08-31-10

Mounting and Removing Flat Panel Screen

WARNING

Always use an assistant or mechanical lifting equipment to safely lift and position the flat panel screen.

3

Hook adapter brackets (BB) onto wall plate (AA).

Then slowly swing screen in as shown. Turn safety/

security screws, using security allen wrench (EE), clockwise at least six times to prevent screen from being removed as shown in detail 1 of figure 3.1.

Screen can be adjusted horizontally if desired as shown in figure 3.2.

NOTE: To lock the screen down, tighten safety/ security screws to wall plate as shown in detail 1.

To remove screen from mount, loosen safety/ security screws, swing screen away from mount, and lift screen off of mount.

CAUTION

Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten screws to 40 in. • lb (4.5 N.M.) maximum torque.

AA BB

AA

SAFETY/

SECURITY

SCREWS

BB

DETAIL 1

fig. 3.1

fig. 3.2

8 of 34

ISSUED: 11-09-07 SHEET #: 202-9253-4 08-31-10

© 2009, Peerless Industries, Inc. All rights reserved. All other brand and product names are trademarks or registered trademarks of their respective owners.

Peerless Industries, Inc.

3215 W. North Ave. Melrose Park, IL 60160 www.peerlessmounts.com

Instalación y montaje:

SmartMount® Montura Universal para Pared Plana para pantallas LCD de panel plano

N.o de modelo

Gama de tamaño de las pantallas

Capacidad de carga máxima de UL

SF670, SF670-S, SF670P, SF670P-S

42'' - 71'' (107 - 180 cm)

250 lb (113 kg)

SWS510/BK, SWS510/SI

 

 

 

 

 

SF680*, SF680-S*, SF680P*, SF680P-S*

61'' - 102'' (155 - 259 cm)

350 lb (159 kg)

*no evaluados por GS

C U© L US

I D :00

0

 

2

76

0018

 

(SF670)

(SF680)

Características:

Colores: plateado o negro

El diseño esbelto sostiene la pantalla cerca de la pared

La pantalla sencillamente se engancha a la placa de pared para proporcionar una instalación rápida y fácil

Ajuste horizontal opcional de hasta 12" (305 mm) (dependiendo del modelo de la pantalla)

Incluye los accesorios para instalaciones en montantes de madera, concreto y bloques de hormigón de escorias

Tornillos de seguridad antirrobo

PUBLICADO: 11-09-07 HOJA #: 202-9253-4 08-31-10

Español

NOTA: Lea la hoja de instrucciones completa antes de comenzar la instalación y el ensamblaje.

ADVERTENCIA

No comience a instalar su producto de Peerless hasta haber leído y entendido las instrucciones y las advertencias contenidas en la Hoja de Instalación. Si tiene alguna pregunta acerca de cualquiera de las instrucciones o las advertencias, por favor, llame a Servicio al Cliente de Peerless al 1-800-865-2112 si está en EE. UU. Si es un cliente internacional, por favor, comuníquese con su distribuidor local.

Este producto sólo debe ser instalado por una persona que tenga una buena aptitud mecánica, que tenga experiencia en construcción básica de edificios y que entienda estas instrucciones en su totalidad.

Asegúrese de que la superficie de apoyo sostendrá, con seguridad, la carga combinada del equipo y todos los fi- jadores y componentes.

Nunca sobrepase la capacidad máxima de soportar carga. Vea la página 9.

Si va a instalar el producto en una pared con montantes de madera, asegúrese de que los tornillos de montaje estén anclados en el centro de los montantes. Se recomienda utilizar un localizador de montantes de "borde a borde".

Siempre cuente con la ayuda de un asistente o utilice un equipo mecánico de izar para levantar y colocar el equipo con más seguridad.

Apriete los tornillos con firmeza, pero no en exceso. Apretarlos en exceso puede dañar los artículos y puede disminuir significativamente su fuerza de fijación.

Este producto está diseñado para uso en interiores solamente. Utilizar este producto en exteriores podría causar fallas del producto y lesiones a individuos.

Este producto fue diseñado para ser instalado en paredes con la siguiente construcción solamente:

CONSTRUCCIÓN DE LA PARED

ACCESORIOS NECESARIOS

Montante de madera

Incluido

Viga de madera

Incluido

Concreto macizo

Incluido

Bloque de hormigón de escorias

Incluido

Montante de metal

No lo instale excepto con el juego de accesorios de Peerless para

 

 

montantes de metal - ACC615; (no evaluados por UL)

Ladrillo

Comuníquese con un profesional calificado (no evaluados por UL)

¿Otra superficie o no está seguro?

Comuníquese con un profesional calificado

Herramientas necesarias para el ensamblaje

localizador de montantes (se recomienda uno de "borde a borde")

destornillador phillips

taladro

broca de 5/16" (8 mm) para paredes de concreto y de bloque de hormigón de escorias

broca de 5/32" (4 mm) para paredes con montantes de madera

nivel

Contenido

 

Lista de piezas......................................................................................................................................................................

11

Instalación en una pared con montantes de madera triples................................................................................................

12

Instalación en una pared de concreto macizo o de bloques de hormigón de escorias.......................................................

13

Instalación de los soportes adaptadores.............................................................................................................................

14

Instalación y desinstalación de la pantalla plana ................................................................................................................

16

10 de 34

PUBLICADO: 11-09-07 HOJA #: 202-9253-4 08-31-10

Peerless Industries SWS510-BK, SF670P-S, SF670-S, SWS510-SI, SF680P-S User Manual

 

 

 

 

 

 

 

 

 

Español

SF670,SF670-S, SF670P,SF670P-S, SWS510/BK, SWS510/SI

SF680SF680,-S, SF680P,SF680P-S

 

Antes de comenzar, asegúrese de que su producto incluye todas las piezas ilustradas.

Nº de pieza

 

Descripción

 

Cant.

Nº de pieza

Nº de pieza

Nº de pieza

 

 

 

Las piezas podrían verse ligeramente diferentes a las ilustradas.

 

 

 

 

 

Lista de piezas

 

 

 

 

SWS510/BK

SWS510/SI

 

 

 

 

 

 

SF680

SF680-S

SF680P

SF680P-S

 

 

 

 

 

 

SF670

SF670-S

SF670P

SF670P-S

X

 

AA

placa de apoyo

 

1

200-1901

200-4901

200-1901

200-4901

 

X

 

 

 

 

200-1902

200-4902

200-1902

200-4902

X

 

BB

soporte adaptador

 

2

200-0942

200-0943

200-0940

200-0941

 

X

 

 

 

 

200-0946

200-0947

200-0944

200-0945

X

X

CC

tornillo para madera Nº14 x 2.5

6

5S1-015-C03

5S1-015-C03

5S1-015-C03

5S1-015-C03

X

X

DD

anclaje para concreto

 

6

590-0320

590-0320

590-0320

590-0320

X

X

EE

Ilave allen de 4 mm

 

1

560-1727

560-1727

560-1727

560-1727

 

X

GG WRUQLOOR 0 [ PP

 

4

520-1305

520-1305

520-1305

520-1305

 

X

HH arandela

 

6

5W1-035-X01 5W1-035-X01

5W1-035-X01

5W1-035-X01

 

AA

BB

 

 

 

CC

 

 

 

 

 

GG

or

 

 

DD

 

 

 

 

 

 

 

 

 

 

 

HH

 

 

 

 

 

 

 

 

 

 

EE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fijaciones para los soportes adaptadores

 

M4 x 12 mm (6)

M5 x 12 mm (4)

 

 

 

(504-9013)

(520-1027)

M6 x 12 mm (4)

 

 

 

 

 

 

M4 x 25 mm (4)

M5 x 25 mm (4)

(520-1128)

M6 x 20 mm (4)

 

(504-1015)

(520-9543)

 

M6 x 30 mm (4)

 

 

 

(520-9402)

(510-9109)

 

 

 

 

.5" espaciador (4)

(540-1057)

M6 x 25 mm (4) (520-1208)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

multi-arandelas (6)

M8 x 25 mm (4)

 

 

 

 

M8 x 40 mm (4)

(580-1036)

(520-1031)

.75" espaciador (4)

M8 x 16 mm (6)

(540-1059)

(520-9257)

(520-1136)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11 de 34

 

 

PUBLICADO: 11-09-07 HOJA #: 202-9253-4 08-31-10

Loading...
+ 23 hidden pages