Peerless Industries PM 13W, PM 13S, PM 20S, PM 20C, PM 27S User Manual

...
0 (0)

Installation and Assembly - TV Wall Mount Models: PM 13, PM 13S, PM 13W, PM 20,

PM 20C, PM 20S, PM 20W, PM 27, PM 27C, PM 27S, PM 27W

R

WARNING

Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call Peerless customer service at 1-800-729-0307.

This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.

Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

Never mount this product to a metal stud wall construction unless the stud can be verified to be constructed of 25 gauge steel minimum, the drywall is 1/2" thick minimum and you obtain and use the Peerless accessory kit for metal studs.

Never exceed the Maximum UL Load Capacity.

If mounting to wood wall stud wall construction, make sure that mounting screws are anchored into the center of the studs. Use of an "edge to edge" stud finder is highly recommended.

Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

Tighten screws and nuts firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power. See suggested torque values where applicable within these instructions.

IMPORTANT! Certain types of walls require additional mounting hardware...

WALL CONSTRUCTION

Wood Stud, Wood Beam

Solid Concrete, Cinder

Block

Metal Stud (Attachment to metal studs has not been evaluated by UL and the product is not UL listed if attached to metal studs.)

ADDITIONAL HARDWARE REQUIRED none

Contact Customer Service for accessory kit unless you have a PM 20C or PM 27C which includes concrete fasteners

Do not attach except with Peerless accessory kit for metal studs; Contact Customer Service for Peerless accessory kit for metal studs.

Other or unsure?

Contact Customer Service

C D E

A B F G

H E

I

K

PM 13, PM 13S,

The Maximum UL Load Capacity for this

PM 13W

product is rated up to 13" TV, 125 lb

 

 

PM 20, PM 20C,

The Maximum UL Load Capacity for this

PM 20S, PM 20W

product is rated up to 20" TV, 125 lb

 

 

PM 27, PM 27C,

The Maximum UL Load Capacity for this

PM 27S, PM 27W

product is rated up to 27" TV, 125 lb

 

 

Before you start make sure all of the parts shown are included with your product. See page 5 for a complete parts list.

J

L

M

N

1 of 12

ISSUED: 07-17-96 SHEET #: 170-9001-7 10-26-04

Visit the Peerless Web Site at www.peerlessindustries.com

For customer service call 1-800-729-0307 or 708-865-8870.

PLAN AHEAD! If you wish to

 

mount TV as close to ceiling

3" (76 mm)

as possible measure TV height

X

and use dimensions provided to

calculate dimension X.

 

 

13" (330 mm) *

 

16.5" (419 mm) **

*PM 13, PM 13S, PM 13W, PM 20, PM 20S, PM 20W, PM 20C

**PM 27, PM 27S, PM 27W, PM 27C, PM 27WC

BESURE

TO DRILL

INTO STUD

CENTERS!

5/32" (4 mm)

A B

3/8" (10 mm)

F

For Wood Stud Walls (for concrete skip to step 4) drill three 5/32" (4 mm) dia. holes 2 1/2" (65 mm) deep. Attach wall bracket (F) using #14 x 2.5 (6 mm x 65 mm) wood screws (A) and plastic bushings (B).

WARNING

Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.

Never tighten in excess of 80 in. • lb (9 N.M.).

Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is highly recommended.

2 of 12

ISSUED: 07-17-96 SHEET #: 170-9001-7 10-26-04

Visit the Peerless Web Site at www.peerlessindustries.com

For customer service call 1-800-729-0307 or 708-865-8870.

WARNING

If your model does not include concrete fasteners, contact customer service for the appropriate accessory kit to install the product on concrete or cinder block.

When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete surface in the 5/16" diameter hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components.

Never exceed the Maximum UL Load Capacity.

For attachment to solid concrete

 

 

 

 

or cinder block wall drill, 5/16" (8

 

 

 

 

mm) dia. holes 1.75" (45 mm) deep

 

5/16" (8 mm)

 

5/16" (8 mm)

using a standard drill and masonry bit

 

 

 

 

(DO NOT use a hammer drill). Attach

 

 

 

 

wall bracket (F) using Concrete

 

 

 

 

Anchor Kit as pictured below.

 

 

 

 

Tighten to 80 in. lbs. (9 N.M.) maxi-

 

 

 

 

mum torque.

 

 

 

 

 

F

Insert and

 

F

 

F

 

hammer in

 

 

 

anchor.

 

 

 

 

Tighten to 80 in.

Always

expansion anchors directly to

lbs. (9 N.M.)

 

load-

.

maximum

Never

expansion anchors to concrete

torque. The

 

covered

drywall, or other finishing mate-

anchor will

 

 

rial. If

concrete surfaces covered with a

expand and grip

 

 

finishing

is unavoidable, the finishing surface

inside the hole.

 

 

must be counterbored.

 

 

 

WARNING

FINISHING

 

SURFACE

 

 

• Tighten concrete anchor bolt firmly, but do not over-

 

F

 

 

 

tighten. Overtightening can damage the bolt, greatly

 

 

 

reducing its holding power.

 

CONCRETE

Never tighten in excess of 80 in • lb (9 N.M.).

 

 

O

 

 

 

 

 

3 of 12

07-17-96 SHEET #: 170-9001-7 10-26-04

Visit the Peerless Web Site at www.peerlessindustries.com

 

For customer service call 1-800-729-0307 or 708-865-8870.

Peerless Industries PM 13W, PM 13S, PM 20S, PM 20C, PM 27S User Manual

Complete the wall mount assembly as shown. Note: If installing a VCR mount refer to that instruction before completing this step.

E

F

E

Snap bushings

(E) into wall bracket (F).

C

C

C

D

F F

K K K

Insert support arm

Join support arm

(K) into wall bracket

(K) and support

(F), then insert

arm retainer (C)

support arm

with retainer pin

retainer (C).

(D). Note: A gentle

 

tap with a hammer

 

may be necessary

 

to insert retainer

 

pin (D).

Support arm retainer (C) will hold support arm (K) in place on wall bracket (F).

11/16" (17 mm)

G

J I H

K

Choose from one of three tilt positions.

L

 

 

00

 

 

50

 

 

100

N

K

M

 

N

 

4 of 12

ISSUED: 07-17-96 SHEET #: 170-9001-7 10-26-04

Visit the Peerless Web Site at www.peerlessindustries.com

For customer service call 1-800-729-0307 or 708-865-8870.

Loading...
+ 8 hidden pages