PARADIGM PDM41024LA15TI, PDM41024LA15TITR, PDM41024LA15TITY, PDM41024LA15TSO, PDM41024LA15TSOA Datasheet

...
0 (0)
PARADIGM PDM41024LA15TI, PDM41024LA15TITR, PDM41024LA15TITY, PDM41024LA15TSO, PDM41024LA15TSOA Datasheet

PDM41024

1 Megabit Static RAM

128K x 8-Bit

Features

High-speed access times

Com’l: 10, 12 and 15 ns

Ind’l: 12 and 15 ns

Low power operation (typical)

-PDM41024SA Active: 450 mW Standby: 50 mW

-PDM41024LA Active: 400 mW Standby: 25mW

Single +5V (±10%) power supply TTL-compatible inputs and outputs Packages

Plastic SOJ (300 mil) - TSO Plastic SOJ (400 mil) - SO Plastic TSOP (I)- T

Description

The PDM41024 is a high-performance CMOS static RAM organized as 131,072 x 8 bits. Writing is accomplished when the write enable (WE) and the chip enable (CE1) inputs are both LOW and CE2 is HIGH. Reading is accomplished when WE and CE2 remain HIGH and CE1 and OE are both LOW.

The PDM41024 operates from a single +5V power supply and all the inputs and outputs are fully TTLcompatible. The PDM41024 comes in two versions: the standard power version (SA) and the low power version (LA). The two versions are functionally the same and differ only in their power consumption.

The PDM41024 is available in a 32-pin plastic TSOP (I), and a 300-mil and 400-mil plastic SOJ.

Functional Block Diagram

 

A 0

 

 

 

 

 

 

 

 

 

Decoder

Memory

 

 

 

Addresses

 

Matrix

 

 

 

 

 

 

A16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

I/O0

 

 

Input

Column I/O

 

 

 

 

 

 

 

Data

 

 

 

 

 

 

Control

 

 

 

 

 

 

 

 

 

 

 

 

 

I/O7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CE1

 

 

 

 

 

 

CE2

 

 

 

 

 

 

Control

 

 

 

 

 

 

WE

 

 

 

 

 

 

 

OE

 

 

 

 

 

 

 

1

2

3

4

5

6

7

8

9

10

11

12

Rev. 3.3 - 4/09/98

1

PDM41024

Pin Configuration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TSOP (I)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SOJ

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

32

Vcc

 

 

A11

 

1

 

 

 

 

32

 

 

OE

 

 

 

 

 

 

 

 

NC

 

 

 

A9

 

2

 

 

 

 

31

 

 

A10

 

 

 

 

 

 

 

 

A16

2

 

31

A15

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A8

 

3

 

 

 

 

30

 

 

CE1

 

 

 

 

 

 

 

 

A14

3

 

30

CE2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A13

 

4

 

 

 

 

29

 

 

I/O7

 

 

 

 

 

 

 

 

 

 

 

29

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A12

4

 

WE

 

 

WE

 

5

 

 

 

 

28

 

 

I/O6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A13

 

 

CE2

 

6

 

 

 

 

27

 

 

I/O5

 

 

 

 

 

 

 

 

A7

5

 

28

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A15

 

7

 

 

 

 

26

 

 

I/O4

 

 

 

 

 

 

 

 

A6

6

 

27

A8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Vcc

 

8

 

 

 

 

25

 

 

I/O3

 

 

 

 

 

 

 

 

A5

7

 

26

A9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NC

 

9

 

 

 

 

24

 

 

Vss

 

 

 

 

 

 

 

 

A4

8

 

25

A11

 

 

A16

 

10

 

 

 

 

23

 

 

I/O2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24

 

 

 

 

 

 

A14

 

11

 

 

 

 

22

 

 

I/O1

 

 

 

 

 

 

 

 

A3

9

 

 

OE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A12

 

12

 

 

 

 

21

 

 

I/O0

 

 

 

 

 

 

 

 

A2

10

 

23

A10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A7

 

13

 

 

 

 

20

 

 

A0

 

 

 

 

 

 

 

 

 

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A1

 

22

CE1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A6

 

14

 

 

 

 

19

 

 

A1

 

 

 

 

 

 

 

 

A0

12

 

21

I/O7

 

 

A5

 

15

 

 

 

 

18

 

 

A2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13

 

20

I/O6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A4

 

16

 

 

 

 

17

 

 

A3

 

 

 

 

 

 

 

 

I/O0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

I/O1

14

 

19

I/O5

 

Pin Description

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

I/O2

15

 

18

I/O4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Vss

16

 

17

I/O3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Name

 

 

Description

 

Truth Table(1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A16-A0

 

 

Address Inputs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

I/O7-I/O0

 

Data Inputs/Outputs

 

 

 

OE

 

 

 

WE

 

 

 

CE1

 

 

 

CE2

I/O

 

 

 

MODE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Output Enable Input

 

 

 

 

X

 

 

 

 

X

 

 

H

 

 

X

Hi-Z

 

 

 

Standby

OE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Write Enable Input

 

 

 

 

X

 

 

 

 

X

 

 

X

 

 

L

Hi-Z

 

 

 

Standby

 

 

WE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CE2

 

Chip Enable Inputs

 

 

 

 

L

 

 

 

 

H

 

 

L

 

 

H

DOUT

 

 

 

 

Read

 

 

CE1,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NC

 

 

No Connect

 

 

 

 

X

 

 

 

 

L

 

 

L

 

 

H

DIN

 

 

 

 

Write

 

VCC

 

 

Power (+5V)

 

 

 

 

H

 

 

 

 

H

 

 

L

 

 

H

Hi-Z

 

 

Output Disable

 

 

VSS

 

 

Ground

 

 

NOTE: 1. H = V

IH

, L = V

IL

, X = DON’T CARE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Absolute Maximum Ratings (1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Symbol

Rating

 

 

 

 

 

 

 

 

Com’l.

 

 

 

Ind.

 

 

Unit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VTERM

Terminal Voltage with Respect to VSS

 

 

 

 

–0.5 to +7.0

 

 

–0.5 to +7.0

 

 

V

 

 

 

 

 

 

 

 

 

 

TBIAS

Temperature Under Bias

 

 

 

 

 

 

 

 

–55 to +125

 

 

–65 to +135

 

 

°C

 

 

 

 

 

 

 

 

 

 

TSTG

Storage Temperature

 

 

 

 

 

 

 

 

–55 to +125

 

 

–65 to +150

 

 

°C

 

 

 

 

 

 

 

 

 

 

PT

Power Dissipation

 

 

 

 

 

 

 

 

 

 

1.0

 

 

 

 

 

1.0

 

 

 

W

 

 

 

 

 

 

 

 

 

 

IOUT

DC Output Current

 

 

 

 

 

 

 

 

 

 

50

 

 

 

 

 

50

 

 

 

mA

 

 

 

 

 

 

 

 

 

 

Tj

Maximum Junction Temperature (2)

 

 

 

 

125

 

 

 

 

 

145

 

 

 

°C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device.This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.

2.Appropriate thermal calculations should be performed in all cases and specifically for

those where the chosen package has a large thermal resistance (e.g., TSOP). The cal-

culation should be of the form: Tj = Ta + P * θja where Ta is the ambient temperature, P is average operating power and θja the thermal resistance of the package. For this product, use the following θja values:

SOJ: 72o C/W

TSOP: 95o C/W

2

4/09/98 - Rev. 3.3

 

 

 

 

 

PDM41024

Recommended DC Operating Condition

 

 

 

 

 

 

 

 

 

 

Symbol

Parameter

Min.

Typ.

Max.

Unit

 

 

 

 

 

 

VCC

Supply Voltage

4.5

5.0

5.5

V

VSS

Supply Voltage

0

0

0

V

Industrial

Ambient Temperature

–40

25

85

°C

 

 

 

 

 

 

Commercial

Ambient Temperature

0

25

70

°C

 

 

 

 

 

 

DC Electrical Characteristics (VCC = 5.0V ± 10%)

 

 

 

 

 

 

PDM41024SA

PDM41024LA

 

 

 

 

 

 

 

 

 

 

 

Symbol

Parameter

 

Test Conditions

 

Min.

Max.

Min.

Max.

Unit

 

 

 

 

 

 

 

 

 

ILI

Input Leakage Current

VCC = MAX., VIN = VSS to VCC

Com’l/

–5

5

–1

1

A

 

 

 

 

 

Ind.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ILO

Output Leakage Current

VCC = MAX.,

Com’l/

–5

5

–1

1

A

 

 

 

CE1

= VIH and CE2 = VIL,

Ind.

 

 

 

 

 

 

 

 

VOUT = VSS to VCC

 

 

 

 

 

 

VIL

Input Low Voltage

 

 

 

 

–0.5(1)

0.8

–0.5(1)

0.8

V

VIH

Input High Voltage

 

 

 

 

2.2

6.0

2.2

6.0

V

VOL

Output Low Voltage

IOL = 8 mA, VCC = Min.

 

0.4

0.4

V

 

 

 

IOL = 10 mA, VCC = Min.

 

0.5

0.5

V

VOH

Output High Voltage

IOH = –4 mA, VCC = Min.

 

2.4

2.4

V

NOTE: 1. VIL(min) = –3.0V for pulse width less than 20 ns

Power Supply Characteristics

 

 

 

 

 

 

 

-10

-12

 

-15

 

Symbol

 

Parameter

Power

Com’l.

Com’l.

 

Ind.

Com’l.

 

Ind.

ICC

 

Operating Current

SA

250

230

 

240

185

 

195

 

 

CE1

 

= VIL and CE2 = VIH

 

 

 

 

 

 

 

 

 

 

f = fMAX = 1/tRC

LA

230

210

 

220

165

 

175

 

 

VCC = Max.

 

 

 

 

 

 

 

 

 

 

IOUT = 0 mA

 

 

 

 

 

 

 

 

ISB

 

Standby Current

SA

80

70

 

70

55

 

55

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CE1 = VIH and CE2 = VIL

 

 

 

 

 

 

 

 

 

 

f = fMAX = 1/tRC

LA

75

65

 

65

50

 

50

 

 

VCC = Max.

 

 

 

 

 

 

 

 

ISB1

 

Full Standby Current

SA

20

20

 

25

10

 

15

 

 

 

VHC and CE2 VLC

 

 

 

 

 

 

 

 

 

 

CE1

 

 

 

 

 

 

 

 

 

 

f = 0

LA

10

10

 

10

5

 

10

 

 

VCC = Max.

 

 

 

 

 

 

 

 

 

 

VIN VCC – 0.2V or 0.2V

 

 

 

 

 

 

 

 

SHADED AREAS = PRELIMINARY DATA

NOTES: All values are maximum guaranteed values.

VLC 0.2V, VHC VCC – 0.2V

Rev. 3.3 - 4/09/98

3

1

2

3

4

5

6

7

8

9

10

11

12

Loading...
+ 5 hidden pages