|
S1A THRU S1M |
|
SURFACE MOUNT RECTIFIER |
|
VOLTAGE - 50 to 1000 Volts CURRENT - 1.0 Ampere |
FEATURES |
|
• |
SMB/DO-214AA |
For surface mounted applications |
|
• High temperature metallurgically bonded-no |
|
|
compression contacts as found in other |
|
diode-constructed rectifiers |
• |
Glass passivated junction |
• Built-in strain relief • Easy pick and place
• Plastic package has Underwriters Laboratory Flammability Classification 94V-O
• Complete device submersible temperature of 260 ¢J for 10 seconds in solder bath
MECHANICAL DATA
Case: JEDEC DO-214AA molded plastic
Terminals: Solder plated, solderable per MIL-STD-750,
Method 2026
Polarity: Indicated by cathode band
Standard packaging: 12mm tape (EIA-481)
Weight: 0.003 ounce, 0.093 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 ¢J ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
|
SYMBOLS |
S1A |
S1B |
S1D |
S1G |
S1J |
S1K |
S1M |
UNITS |
Maximum Recurrent Peak Reverse Voltage |
VRRM |
50 |
100 |
200 |
400 |
600 |
800 |
1000 |
Volts |
Maximum RMS Voltage |
VRMS |
35 |
70 |
140 |
280 |
420 |
560 |
700 |
Volts |
Maximum DC Blocking Voltage |
VDC |
50 |
100 |
200 |
400 |
600 |
800 |
1000 |
Volts |
Maximum Average Forward Rectified Current, |
I(AV) |
|
|
|
1.0 |
|
|
|
Amps |
at TL=100 ¢J |
|
|
|
|
|
|
|
|
|
Peak Forward Surge Current 8.3ms single half sine- |
IFSM |
|
|
|
30.0 |
|
|
|
Amps |
wave superimposed on rated load(JEDEC method) |
|
|
|
|
|
|
|
|
|
Maximum Instantaneous Forward Voltage at 1.0A |
VF |
|
|
|
1.10 |
|
|
|
Volts |
Maximum DC Reverse Current TA=25 ¢J |
IR |
|
|
|
5.0 |
|
|
|
£g A |
At Rated DC Blocking Voltage TA=125 ¢J |
|
|
|
|
50 |
|
|
|
|
Maximum Reverse Recovery Time (Note 1) |
TRR |
|
|
|
2.5 |
|
|
|
£g S |
Typical Junction capacitance (Note 2) |
CJ |
|
|
|
12 |
|
|
|
PF |
Typical Thermal Resistance (Note 3) |
R £KJL |
|
|
|
30.0 |
|
|
|
¢J /W |
|
|
|
|
|
|
|
|
||
Operating and Storage Temperature Range |
TJ,TSTG |
|
|
-55 to +150 |
|
|
¢J |
||
NOTES: |
|
|
|
|
|
|
|
|
|
1.Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, Irr=0.25A
2.Measured at 1 MHz and Applied Vr=4.0 volts
3.8.0mm2 (.013mm thick) land areas