Panasonic TY-SP42PWD3W, TY-CE42PS1, TY-ST42PW1, TY-SP42PM3W, TY-ST42PT3S User Manual

Pedestal

TY-ST42PT3S TY-ST42PT3K

Wall stand

TY-ST42PW1

Mobile stand

TY-ST42PF3

Wall-hanging bracket (vertical)

TY-WK42PV1

Wall-hanging bracket (angled)

TY-WK42PR1

Ceiling unit

TY-CE42PS1

Speakers

TY-SP42PM3W TY-SP42PWD3W

How to use this manual

Some notes on how to read this manual

In this manual, the number such as "1, 2, 3,..." appears to the left of each step.

Go ahead in numerical order.

Indicates a situation where incorrect handling may result in death or serious injury for the person performing the installation.

Indicates a situation where incorrect handling may result in breakdown or damage to physical objects.

Contains more detailed information than in the steps in the main text. Be sure to read the notes.

Other notes

•More-detailed explanations and supplemental information for the installation procedures are given on the right. * Be sure to read not just the steps on the left, but the information on the right as well.

•At the very beginning of the installation procedure, there are illustrations for assembling various accessory parts on the Wide Plasma Display. Refer to them when installing.

•Each installation procedure for accessory parts is preceded by a brief description of the procedure. During the pro-cedure, refer to the description if necessary.

•Each installation procedure for accessory parts is followed by an explanation of how to remove the Wide Plasma Display. Refer to this when it is necessary to remove the accessory parts from the Wide Plasma Display and reposition it.

Before installing

Be sure to read through these instructions before starting the installation.

The installation should be only performed by a professional person.

If any parts are not installed correctly, the display unit may fall, possibly resulting in damage and personal injury.

Failure to follow Warning instructions may result in damage and personal injury.

Make sure that all safety conditions regarding strength at installation are observed.

If the installation strength is insufficient, the display unit may fall and personal injury may result.

Do not install in places which are unable to bear the weight of the display.

If the strength of the floor and wall at the site of installation is insufficient, the display unit may fall, possibly resulting in damage and personal injury.

A caution indicates special precautions against actions which may result in fire or electric shock.

Do not install in places subject to humidity, dust, oil fumes, condensation or excessive heat.

These factors may adversely affect the Wide Plasma Display, possibly resulting in fire or electric shock.

Do not install the Wide Plasma Display horizontally with the screen facing up, or sideways or upside down.

Installing the screen other than in the conventional viewing setting may cause heat to build up inside the display and possibly result in fire.

Two persons are required to install and remove the display unit.

The display unit is heavy and at least two persons are needed to handle it safely. The display unit may drop and personal injury may result if one person attempts to install it without assistance.

Maintain a space of at least 10 cm respectively at the top, bottom and sides of the display unit and at least 1.9 cm at the rear of the display unit.

The display unit has air outlet holes at the top and air intake holes at the bottom and rear. These holes must not be blocked, nor airflow not be obstructed. Otherwise fire may result.

Tools list

The tools in the following tables are necessary for complete assembly.

Before attempting to install the accessories, make sure you have the following tools on hand.

	Plus screw driver	Clean cloth	Drill	Measure	Level gauge
Pedestal			–	–	–
Wall stand
Mobile stand			–	–	–
Wall-hanging
bracket (vertical)
Wall-hanging
bracket (angled)
Ceiling unit

Optional parts list

	Wire or Chain	M6 bolt x 6
Pedestal		–
Wall stand	–
Mobile stand	–	–
Wall-hanging	–
bracket (vertical)
Wall-hanging	–
bracket (angled)
Ceiling unit

Accessory list

1

Pedestal

4

Wall-hanging bracket (vertical)

TY-ST42PT3-S
TY-ST42PT3-K	TY-WK42PV1
	5 Wall-hanging bracket (angled)

2 Wall stand

TY-WK42PR1

6 Ceiling unit

TY-ST42PW1

3 Mobile stand

TY-CE42PS1

7 Speakers

TY-ST42PF3	TY-SP42PM3W
	TY-SP42PWD3W

For information on the wiring of the Wide Plasma Display after installing accessories, be sure to refer to the documentation that comes with the Wide Plasma Display.

Parts list

Check the part number before performing the installation procedure.

Pedestal

Base	Assembly screw(M5-20) x 4	Wood screw x 2
	Assembly screw (M5-30) x 4	Black screw x 2
Pole x 2	Band x 2	Clamp x 4
	Black screw x 2

Wall stand

Wall pedestal	Fixing screw (M5) x 2	Allen key (accessory)
	Pan head bolt with hex socket	Insulating spacer x 4
	(M8-45) x 4
	Fixing screw (M5) x 2 Assembly	Toothed pan washer x 4

Holding bracket

Mobile stand

Holder	Shelf	Stand base	Support x 2
Cable strap x 5	Bolt (M8)x 4	Assembly screw (M6-16)
		and spring washer x 4 each
Assembly screw (M5-15) x 4	Assembly screw (M5-30) x 4

Wall-hanging bracket ( vertical )

Wall-hanging bracket unit

Fixing screw (M5) x 2

Allen key (accessory)

Pan head bolt with hex socket (M8-45) x 4

Tooted pan	Insulating
washer x 4	spacer x 4

Wall-hanging bracket ( angled )

Wall-hanging bracket unit

Fixing screw (M5-35) x 2

Allen key (accessory)

Pan head bolt with hex socket (M8-45) x 4

Tooted pan	Insulating
washer x 4	spacer x 4

Ceiling unit

Ceiling unit

Insulating spacer x 4

Fixing bolt (M8-12) x 2

Allen key

Fixing screw (M5) x 2

	Fixing bolt (M8-100)	Fixing bolt (M8-20) x 2
Pan head bolt with hex socket	Spring washer	Cable tie x 2
(M8-45) x 4
Toothed pan washer x 4	Washer pan nut (M8)

Speakers

Speaker x 2	Mounting bracket	Bracket mounting	Speaker cable
	(right) x 2	Assembly screw (M4-10) x 12	(20 cm) x 2
	Mounting bracket	Sponge x 2
	(left) x 2

Points to note during installation

• This ceiling unit is for mounting a Wide Plasma Display to a ceiling for viewing pur poses. Do not use it for any type of installation other than ceiling mounting.

• In order to ensure correct, problem-free operation of the Wide Plasma Display, do not install the Display in any of the following places:

• Next to sprinklers or sensors

• Where it may be subject to vibration or shocks

• Near high-voltage wires or electric motors

• Where it may be in direct contact with air from heaters

• When installing this ceiling unit, use a fixing method appropriate to the type of ceiling.

• Insert the mains plug for the Wide Plasma Display into a mains socket which is close and easily accessible.

• Provide adequate ventilation so that the temperature around the display does not rise above 40° C (104 F° ).

If there is insufficient movement of the air inside the display, heat may build up inside the display and fire may result.

•For U.S.A (TH-42PW3 / TH-42PWD3 only)

If the connection cable cannot reach the Display when it has been installed to the wall, use the 15 m cable (TYSCP15C03) which is sold separately.

Dimensions of the display unit

Units : mm

						1020
50						920				50
46
										518	610
46
		489									89
											44
											615
98	112.2		390.9						65
	L								L
	AUDIO								AUDIO
S-VIDEO	VIDEO	VD	HD	PR/CR/R		PB/CB/B		Y/G		AUDIO
	R								R
	AV IN		COMPONENT/RGB IN						PC IN	TUNER IN	SERIAL
18.5		18		18	18		18		20	53.86	39.43
22	35.7
70.69									296

To connect the power cord and others, refer to the documentation that comes with the Wide Plasma Display.

Pedestal

TY-ST42PT3S

TY-ST42PT3K

Assembly diagram

CONTENTS

Instruction of the installation ......................	1-2
1.Assembling the pedestal....................................	1-2
2.Attaching the pedestal to the display unit ..............	1-2
3.Fixing the display unit .......................................	1-3

1-1

Instruction of the installation

	Assembling the pedestal
1	Put the poles into the outer holes on the base, and fasten the four
	screws.

Attaching the pedestal to the display unit

1

Spread a clean cloth over a level floor or base, and place on it the display

unit face down.

Remove the screws and covers.

Keep them in a safe place for possible future use.

Ensure that the poles sit flush with the bottom of the base.

Assembly screw (M5-20) x 4

Place the display face down on a cloth clean and free from other foregin particles, and then proceed to the next step.

1-2

2	Insert the two poles at the top of the pedestal into the holes in the base
	of the display unit as shown in the illustration below.
3	Insert the four screws, two on each side, into the holes in the back
	of the display unit and screw them into the holes on the inserted poles.

Front

Rear

Fixing the display unit

Fixing the display unit to a desk.

1	Screw the bands to the pedestal with	screws.
2	Screw the bands to edge of a desk with	screws.

Assembly screw (M5-30) x 4

Band x 2

Black screw x 2

Wood screw x 2

I f yo u a r e u s i n g a wooden desk, then use the wood screws.

Use the appropriate screws for the type of material of the desk.

1-3

Fixing the display unit to the wall

1 Insertunit. the screws and clamp into the holes at the back of the display

2	Use a strong wire or chain commercially available to fix the display unit
	to a solid area of the wall or pillar.

Black screw x 2

Clamp x 4

1-4

Wall stand

TY-ST42PW1

Assembly diagram

CONTENTS

Description ...................................................	2-2
Instruction of the installation ......................	2-3
1.Assembling the wall stand ..................................	2-3
2.Fixing the insulating spacers to the display unit ......	2-4
3.Attaching the wall stand to the display unit ............	2-6
4.Fixing the display unit to the wall .........................	2-7
Removing the display unit...........................	2-8

2-1

Description

Installation diagram

Units : mm

400 (153/4)

611.5 (245/64)

1020 (405/32)

744 (2919/64)

560 (221/16)

390 (1523/64)

19 (3/4)

89 (333/64) *100

(431116.5 61 / )64 (24610 1 / )64

* A clearance of at least 100mm at the top of the display unit should be provided.

2-2

Instruction of the installation

Assembling the wall stand

1 Check the strength of the installation location.

The height measurements marked ** are particularly important. Do not attempt to set up the pedestal in a location where these dimensions and a clearance of at least 100 mm at the top of the display unit should be provided.

1)On the wall, measure and mark a height 650 mm above the floor;

2)Measure and mark the location 475 mm horizontally to the right of the mark you made in 1). Measure and mark points 180 mm and 360 mm above each mark (for a total of six marked locations);

3)Drill a hole at each of the six marked locations on the wall.

Units : mm

	744 (2919/64)
	560 (22 1/16)
	390 (1523/64)
/32)
3
(7	(15
180
	4)/
	3
(7	400
32)/
3
180

/8)			)
7			16
631.5(24			/
			1
		Wall installation holes	(24
**		(4 locations)	611.5
		Spare wall installation holes	**
		(2 locations)
		Floor surface

Refer to the holding b ra cke t i n s t a l l a t i o n measurements in the drawing left. Ensure that the wall is able to bear the weight at each of the 4 u p p e r a n d l ow e r installation locations.

Add reinforcement if any of these locations are not strong enough.

Ensure an area of at least 650 mm by 1,230 mm in length at the location where you plan to install the holding bracket.

The holding bracket has 6 slits through which the bracket can be fixed to a wall with screws.

If the wall material does not allow sufficient strength by using six installation holes, use some of the spare holes. However, depending on the construction material used at the place of installation, cracks may develop if the screws are inserted too close to each other.

2-3

2 Fix a M6 screw, through any of the slits in the bracket, into the corresponding hole in the wall.

Using a level along the top or bottom edge, ensure that holding bracket is horizontal.

The holding bracket must always be installed. It prevents the display unit from falling after installation.

3	Fix the screws through the slits into the remaining three holes.
4	Provisionally tighten the fixing screws.

Fixing the insulating spacers to the display unit

1	1)	Spread a clean cloth over a level floor or base, and place it on the
		display unit face down.
	2)	Remove the screws and covers.
		Keep them in a safe place for possible future use.

If the screws protrude more than 5 mm, it will n o t b e p o s s i bl e t o proper ly install the display unit.

Carefully place the Wide Plasma Display face down on top of a clean cloth, which has been s p r e a d o ve r a f l a t surface with no other objects on it, and then proceed to the next step.

2-4