Panasonic TC-20LA2, TC-20LA2D User Manual

0 (0)

LCD TV

Operating Instructions

Model No. TC-20LA2

TC-20LA2D

LCD TV shown above is model TC-20LA2.

For assistance, please call : 1-800-211-PANA (7262)

or send e-mail to : consumerproducts@panasonic.com

or visit us at www.panasonic.com (U.S.A)

For assistance, please call : 787-750-4300

or visit us at www.panasonic.com (Puerto Rico)

For assistance, please call : 1-800-561-5505

or visit us at www.panasonic.ca (Canada)

Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference.

English

Espan˜ol [Resumen] TQBC0758

Important Safety Instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrow head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons.

The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance.

■ Note to CATV System Installer: This reminder is provided to direct the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

■Important Safety Instructions for LCD TV

1)Read these instructions. All the safety and operating instructions should be read before the appliance is operated.

2)Keep these instructions.

3)Heed all warnings.

4)Follow all instructions.

5)Do not use this apparatus near water. For example: Avoid placing it near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.

6)Clean only with dry cloth. Unplug this LCD TV from the wall outlet before cleaning. Do not use liquid or aerosol cleaners.

7)Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Slots and openings in the cabinet and the back or bottom are provided for ventilation, and to ensure reliable operation of the LCD TV and to protect it from overheating. These openings must not be blocked or covered. There should be at least 10 cm of space from these openings. The openings should never be blocked by placing the LCD TV on a bed, sofa, rug or other similar surface. This LCD TV should not be placed in a built-in installation such as a bookcase unless proper ventilation is provided.

8)Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9)Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10)Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11)Only use attachments/accessories specified by the manufacturer. Otherwise it may cause hazards.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13)Unplug this apparatus during lightning storms or when unused for long periods of time. This will prevent damage to the receiver due to lightning and power-line surges.

14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Upon completion of any service or repairs to this LCD TV, ask the service technician to perform routine safety checks to determine that the television is in safe operating condition.

15)Operate only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home consult your television dealer or local power company.

16)Follow all warnings and instructions marked on the LCD TV.

17)Never push objects of any kind into this LCD TV through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the LCD TV.

Important Safety Instructions

18)If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. In the U.S. Selection 810-21 of the National Electrical Code provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

19)An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

EXAMPLE OF ANTENNA

GROUNDING AS PER (NEC)

NATIONAL ELECTRICAL

CODE

	ANTENNA
	LEAD-IN WIRE
	GROUND
	CLAMP
	ANTENNA
	DISCHARGE UNIT
ELECTRIC	(NEC SECTION 810-20)
SERVICE
EQUIPMENT	GROUNDING CONDUCTORS
	(NEC SECTION 810-21)
	GROUND CLAMPS
	POWER SERVICE GROUNDING
	ELECTRODE SYSTEM
	(NEC ART 250, PART H)

20)Unplug this LCD TV from the wall outlet, and refer servicing to qualified service personnel under the following conditions:

a.When the power cord or plug is damaged or frayed.

b.If liquid has been spilled into the LCD TV.

c.If the LCD TV has been exposed to rain or water.

d.If the LCD TV does not operate normally by following the operating instructions.

Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the LCD TV to normal operation.

e.If the LCD TV has been dropped or the cabinet has been damaged.

f.When the LCD TV exhibits a distinct change in performance - this indicates a need for service.

21)When replacement parts are required, be sure the service technician to use replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

22)WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

DO NOT PLACE LIQUID CONTAINERS (FLOWER VASES, CUPS, COSMETICS, ETC.) ABOVE THE SET. (INCLUDING ON SHELVES ABOVE, ETC.)

23)CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS PLUG WITH A RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

24)CAUTION: USE WITH OTHER STAND MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY.

25)CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.

NOTE: • This equipment is designed to operate in the U.S.A. and other countries where the broadcasting system and AC house current is exactly the same as in the U.S.A.

•The marking or retained image on the LCD panel resulting from fixed image use is not an operating defect and as such is not covered by Warranty. This product is not designed to display fixed image patterns for extended periods of time.

■Important Information Regarding Use of Video Games, Computers, Captions or Other Fixed Image Displays.

The extended use of fixed image program material can cause a permanent "shadow image" on the LCD panel. This background image is viewable on normal programs in the form of a stationary fixed image. This type of irreversible LCD panel deterioration can be limited by observing the following steps:

A.Reduce the brightness/contrast setting to a minimum viewing level.

B.Do not display the fixed image for extended periods of time.

C.Turn the power off when not in actual use.

■This product utilizes tin-lead solder, and has a fluorescent lamp containing a small amount of mercury. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: www.eiae.org.

Dear Panasonic Customer

Welcome to the Panasonic family of customers.

We hope that you will have many years of enjoyment from your new LCD TV. To obtain maximum benefit from your set, please read these instructions before making any adjustments, and retain them for future reference.

Retain your purchase receipt, and record the model number and serial number of your set in the space provided on the rear cover of these instructions.

For assistance, please call : 1-800-211-PANA (7262)

or send e-mail to : consumerproducts@panasonic.com
or visit us at www.panasonic.com	(U.S.A.)

For assistance, please call : 787-750-4300

or visit us at www.panasonic.com (Puerto Rico)

For assistance, please call : 1-800-561-5505

or visit us at www.panasonic.ca (Canada)

Federal Communication Commission Information

This equipment has been tested and found to comply with the limits for a TV Broadcast Receiver, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause or receive interference, which can be determined by turning equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the TV antenna.

Increase the separation between TV and other equipment.

Connect TV into separate outlet from other equipment.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

The Energy Star label, a symbol for energy efficiency, was created by the U.S. Environmental Protection Agency (EPA) and the U.S. Department of Energy (DOE) to help customers identify products that can save them money and protect the environment by saving energy. Energy Star compliant products generally consume less energy than similar standard products.

Important Safety Instructions ..............................	2
Installation .............................................................	6
SUPPLIED ACCESSORIES ................................	7
Remote control battery installation ......................	7
Maintenance ..........................................................	8
Connections ..........................................................	8
Antenna Connection ............................................	8
Cable Box Connection .........................................	9
Connecting Other Equipment ............................	10
Connecting Headphones / Earphones ...............	11
Power ON / OFF ...................................................	12
Connecting the Plug to the Wall Outlet ..............	12
Turning the Power On ........................................	12
Basic Controls .....................................................	13
Menu Operations .................................................	14
Tuning Channels ................................................	16
LOCK .................................................................	18
CLOSED CAPTION ...........................................	22
INPUT LABEL ....................................................	23
OTHER ADJUST ...............................................	23
PICTURE ADJUST ............................................	24
AUDIO ADJUST .................................................	25
ASPECT Controls ................................................	26

Manual de instrucciones [ Resumen ]
Instalación de las pilas del mando a distancia .....	27
Ajuste el soporte con el ángulo deseado ...	28
Conexión ..........................................................	29
Conexión de antena .....................................	29
Conexión de antena / cable ..........................	29
Conexión del receptor de TV por cable .......	30
Conexión de auriculares ...............................	31
Conexión/desconexión de la alimentación ...	32
Conexión de la clavija a la toma de corriente ...	32
Cómo conectar la alimentación ....................	32
Controles básicos .........................................	33
Operaciones con menús ..............................	34
Sintonización de canales ..............................	36

Troubleshooting ....................................................	38
Specifications ........................................................	39

Installation

Receiver Location

Locate for comfortable viewing. Avoid placing where sunlight or other bright light (including reflections) will fall on the screen.

Use of some types of fluorescent lighting can reduce remote control transmitter range.

Adequate ventilation is essential to prevent internal component failure. Keep away from areas of excessive heat or moisture.

Optional External Equipment

The Video/Audio connection between components can be made with shielded video and audio cables. For best performance, Antenna cables should utilize 75 ohm coaxial shielded wire. Cables are available from your dealer or electronic supply store.

Before you purchase any cables, be sure you know what type of output and input connectors your various components require. Also determine the length of cable you’ll need.

For optimum quality picture

When the LCD is exposed to light from outdoors or lighting fixtures, high-contrast pictures may not be displayed clearly. Turn off florescent lamps near the LCD and place in a location not exposed to outdoor light.

How to use the LCD stand

Adjust the stand to your desired angle.

•TC-20LA2

The stand angle can be adjusted between 5° forward to 15° back, and rotated 30° to the right/left.

•TC-20LA2D

The stand angle is fixed 14° back.

Installation

T V

Remote control battery installation

Requires two AA batteries.

1. Open the battery cover.

2.Install the batteries and replace the cover. Note the correct polarity (+ and -).

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.

Observe the following precautions:

1.Always use new batteries when replacing the old set.

2.Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

3.Battery replacement is necessary when remote control acts sporadically or fails to operate this unit.

Notes:

•Do not drop, apply shock to or step on the remote control.

•Do not spill water on the remote control.

•Do not place objects between the remote control and remote control receiver.

•Do not use remote controls for other equipment at the same time.

•If the TV does not operate even when using the remote control from a close range, it is time to replace the batteries. Refer to the label on back of the remote control for directions on replacing batteries.

Maintenance

	To clean this unit, wipe with a soft, dry cloth.	Mild
	If the surfaces are extremely dirty, use a soft cloth dipped in a soap and	Mild
		detergent
	water solution or a weak detergent solution.
	• Use eyeglass cleaner to remove stubborn dirt from the LCD.
	• Never use alcohol, paint thinner or benzine to clean this unit.
	• Before using a chemically treated cloth, read the instructions that came
	with the cloth carefully.

CAUTION :

If water or similar substances get inside the monitor via the liquid crystal panel surface, a malfunction may result.

Connections

Note:

Cables and adapters are not supplied with this set.

Antenna Connection

For proper reception of VHF/UHF channels, an external antenna is required. For best reception, an outdoor antenna is recommended. The antenna mode must be set to TV (see page 16, MODE).

		Back of the TV
	Antenna Terminal
VHF Antenna	UHF Antenna
		ANT
	75 Ohm	F-Type Antenna
	Coaxial Cable	F-Type Antenna
Mixer		Adapter
Mixer

Antenna / Cable Connection

F-Type Antenna Adapter

Antenna Terminal on the Back of the TV

Incoming 75 Ohm Cable from Home Antenna / Cable Company

Connections

Cable Box Connection

•For reception of cable channels (01 - 125), connect the cable supplied by your local cable company. The antenna mode must be set to CABLE (see page 16, MODE).

•Certain cable systems offset some channels to reduce interference or have Premium (scrambled) channels. A cable converter box is required for proper reception. Check with your local cable company for its compatibility requirements.

•Set the TV channel to CH3 or CH4, cable when using this connection.

Cable Box

Back of the TV

Cable Box and VCR

Back of the TV	CABLE BOX
	OUTPUT INPUT

ANT

VCR

ANT INPUT

OUTPUT

ANT OUTPUT

Incoming 75 Ohm Cable from Home Antenna / Cable Company

S VIDEO VIDEO

L-AUDIO-R

Panasonic TC-20LA2, TC-20LA2D User Manual

Connections

Connecting Other Equipment

DVD/STB

Audio	COMPONENT VIDEO OUT
OUT	COMPONENT VIDEO OUT
OUT
L	Y	Pb	Pr

AUDIO	COMPONENT
cable	VIDEO cable

				Y
			VIDEO
	AUDIO	VIDEO S-VIDEO		PB
R	L	VIDEO S-VIDEO	L
R	L		L
		1	AUDIO	PR
			R
		2
		INPUT	COMPONENT VIDEO INPUT

AUDIO	VIDEO	S-VIDEO cable
cable	cable

Super-VHS VCR	CAMCORDER	VIDEO GAME
		CONSOLE

Audio	Video	S-Video
R OUT L	OUT	OUT

Notes:

•Only 480i and 480p are available through the component input terminals.

•When connecting video cables, priority is given to the S-Video cable when both the S-VIDEO input terminal and the VIDEO input terminal are connected.

•With a monaural VCR, connect the monaural audio cable to the AUDIO-L terminal.

•Please make inquiries to video game manufacturers concerning component cables to connect with video game console.