Machine Vision Camera
GP-MF622
Before attempting to connect or operate this product, please read these instructions completely.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclo-
SA 1965 sure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
|
The exclamation point within an |
|
equilateral triangle is intended to |
|
alert the user to the presence of |
|
important operating and mainte- |
|
nance (servicing) instructions in the |
SA 1966 |
literature accompanying the appli- |
ance. |
|
|
|
Warning:
This equipment generates and uses radio frequency energy and if not installed and used properly, i.e., in strict accordance with the instruction manual, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CONTENTS |
|
PREFACE ....................................................... |
2 |
FEATURES ..................................................... |
2 |
PRECAUTIONS .............................................. |
3 |
MAJOR OPERATING CONTROLS AND |
|
THEIR FUNCTIONS ........................................ |
5 |
PREPARATIONS ............................................. |
9 |
SYSTEM CONNECTIONS ............................. |
10 |
EXTERNAL SYNCHRONIZATION .................. |
11 |
PREVENTION OF BLOOMING AND SMEAR .. |
11 |
SPECIFICATIONS ........................................... |
12 |
OPTIONAL ACCESSORIES ............................. |
13 |
Remove dust on the faceplate of filter glass before mounting the lens on the camera.
- 1 -
The serial number of this product may be found on the top of the unit.
You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft.
Model No.
Serial No.
PREFACE |
|
FEATURES |
The Panasonic GP-MF622 Machine Vision Camera has a 1/2” Interline Transfer CCD image sensor which features 380 000 pixels, a horizontal resolution of 570 lines, and minimum smear.
1.Newly developed multi-function solid state image sensor 1/2” Inter Line Transfer type CCD image sensor with 768 (H) x 494 (V) pixels.
2.Selectable scanning system :
1-line interlace and 2-line interlace are available for the highest quality possible within video processing.
3.External synchronization :
External HD/VD input enables system setup with external video processors, etc.
4.Frame Reset :
External HD and VD reset signals reset the scanning line to the line number 1.
5.High speed shutters up to 1/96 000 second with trigger function enable to achieve strobe-less machine vision system.
- 2 -
PRECAUTIONS
1.Do not attempt to dissemble the camera.
To prevent electric shock, do not remove screws or covers.
There are no serviceable parts inside. Ask a qualified service person for servicing.
2.Handle the camera with care.
Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or shortage.
3.Do not expose the camera to rain or moisture, or try to operate it in wet areas.
This camera is designed for indoor use. Turn the power off immediately and ask a qualified service person for servicing. Moisture can damage the camera and also create the danger of electric shock.
- 3 -
4.Do not use the strong or abrasive detergents when cleaning the camera body.
Use a dry cloth to clean the camera when dirty.
In case the dirt is hard to remove, use a mild detergent and wipe gently.
5.Clean the CCD faceplate with care.
Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton tipped applicator and ethanol.
6.Never face the camera towards the sun.
Do not aim the camera at bright objects. Whether the camera is in use or not, never aim at the sun or other extremely bright objects. Otherwise, blooming or smear may be caused.
Loading...