PANJIT GBJ4K, GBJ4J, GBJ4G, GBJ4D, GBJ4B Datasheet

DATA SHEET

GBJ4A~GBJ4K

GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE - 50 to 800 Volts CURRENT - 4.0 Amperes

Recongnized File #E228882

FEATURES

	• Plastic material has Underwriters Laboratory	(3.0)
	Flammability Classification 94V-O
		0.118
	• Ideal for printed circuit board
		C
	• Reliable low cost construction utilizing molded plastic technique
	• Surge overload rating: 150 Amperes peak	0.146(3.7)		0.129(3.3)
	• High temperature soldering guaranteed:
	260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension

MECHANICAL DATA

Case: Reliable low cost construction utilizing		0.087(2.2)
	0.070(1.8)
molded plastic technique
		0.044(1.1)
Terminals: Leads solderable per MIL-STD-202,	0.035(0.9)

Method 208

	Mounting position: Any	0.304(7.7)
		0.288(7.3)
	Mounting torque: 5 in. lb. Max.
	Weight: 0.15 ounce, 4.0 grams

			GBJ																Unit: inch ( mm )
0.996(25.3)																											0.189(4.8)
0.972(24.7)																											0.173(4.4)
											0.122(3.1)						0.142(3.6)										0.150(3.8)
																											0.133(3.4)
)
												)
14.7												15.3
																						)							)
(												(								9.7									9.3
0.578												0.603								0.382									0.366
																				(									(
			)									)															0.115(2.9)
			17.0									18.0
																											0.098(2.5)
(												(
0.669												0.709
																							0.032(0.8)
									0.304(7.7)										0.024(0.6)
0.288(7.3)
0.304(7.7)
0.288(7.3)

MAXIMUMRATINGSANDELECTRICALCHARACTERISTICS

Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.

For Capacitive load derate current by 20%.

		GBJ4A	GBJ4B	GBJ4D		GBJ4G	GBJ4J	GBJ4K	UNIT
	Maximum Recurrent Peak Reverse Voltage	50	100	200		400	600	800	V
	Maximum RMS Input Voltage	35	70	140		280	420	560	V
	Maximum DC Blocking Voltage	50	100	200		400	600	800	V
	Maximum Average Forward TC=100°C				4.0				A
	Rectified Output Current
	I2t Rating for fusing ( t<8.3ms)				127				A2sec
	Peak Forward Surge Current single sine-wave superimposed on rated load			150					Apk
	(JEDEC method)
	Maximum Instantaneous Forward Voltage Drop per element at 2.0A				1.0				Vpk
	Maximum Reverse Leakage at rated TA=25°				5				µA
	CDc Blocking Voltage per element TC=100°C				500				µA
	Typical Thermal Resistance per leg(Note 2) Rθ JA				8.6				°C / W
	Typical Thermal Resistance per leg(Note 3) Rθ JC				3.1				°C / W
	Operating and Storage Temperature Range, TJ,TSTG			-55 to +150					°C

NOTES:

1.Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.

2.Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.

3.Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.

DATE : OCT.08.2002

PAGE . 1