Orbit Manufacturing Rokonet ORBIT-6 RP-206 User Manual

342.27 Kb
Loading...

INSTALLER MANUAL

VER. B

1

Installer Manual

Customer Information

1.The ORBIT-6 (Model RP-206) complies with FCC Part 68 Rules. On the upper panel of this product is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN is 0.8B). If requested, this information must be provided to the Telephone Company.

2.An FCC compliant telephone connector is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a connector, which is Part 68 compliant.

3.If the ORBIT-6 (RP-206) is not operating properly, it may cause harm to the telephone network. If so, the Telephone Company will notify you in advance that a temporary discontinuance of service may be required. If advance notice is not practical, you will be notified as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if it is necessary.

4.The Telephone Company may make changes in its facilities, equipment, operations, or procedures, which could affect the operation of the equipment. If this happens, the Telephone Company will provide advance notice in order to enable you to make the necessary modifications to maintain uninterrupted service. If the equipment is causing harm to the telephone network, the Telephone Company may request that the equipment be disconnected until the problem is resolved.

5.Connection to telephone company-provided coin service is prohibited. Connection to party line service is subject to state tariffs.

6.If trouble is experienced with the ORBIT-6 (RP-206), for repair and warranty information, please contact your supplier.

For service centers please see back cover.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced Radio/TV technician for help.

Changes or modifications to this unit not expressly approved by Rokonet, Ltd., could void the user's authority to operate the equipment.

This equipment has been approved to Council decision 98/482/EC – “TBR 21” for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries, the approval does not, in itself, give an unconditional assurance of successful operation on every PSTN termination point.

In the event of problems, you should contact your equipment supplier in the first instance.

2

Installer Manual

Copyright © 2001

by Rokonet Ltd.,

14 Hachoma Street

Rishon Letzion 75655

Israel

All rights reserved.

No part of this document may be reproduced in any form without prior written permission from the publisher.

5IN206IM B

3

Installer Manual

Summary of User’s Commands

It is necessary to ARM your system to obtain protection from intrusion.

All other forms of protection, including fire and 24-hour panic alarms (i.e. police, fire, and medical) are always ready to report alarms and do NOT need to be armed.

This page, called a Command Summary, is intended to give you brief summaries of common system operations. More detailed explanations and related information can be found within, by referring to the user manual.

FUNCTION

 

PROCEDURE

 

 

 

 

 

 

System Arming

[USER CODE] + [ARM]

Stay Home Arming

[USER CODE] + [STAY]

Instant Stay

[STAY] + [STAY]

System Disarming

[USER CODE]

Duress Disarming

[DURESS CODE]

Silencing an Alarm

[USER CODE]

Bypassing / Unbypassing a

[ Q ] + [ 1 ] + [USER CODE ] + [ ZONE NUMBER TO BE

Zone

BYPASSED / UNBYPASSED]

Quick Bypassing Zone

[ ZONE NUMBER TO BE BYPASSED ] for at least 2 seconds

Reset Smoke Detector(s)

[ Q ] + [ 2 ] + [USER CODE ] + [UTILITY OUTPUT NUMBER

which is responsible for resetting the Smoke Detector]

 

 

 

Utility Output Operation

[ Q ] + [ 2 ] + [USER CODE ] + [ UTILITY OUTPUT NUMBER ]

Display Troubles

[ Q ] + [ 3 ]

 

 

Display Memory

[ Q ] + [ 4 ]

 

 

Setting/Changing

[ Q] + [ 5 ] + [MASTER CODE] + [CODE NUMBER TO BE

a User Code

SET/CHANGED] + [NEW CODE]

Set Date

[ Q ] + [ 6 ] + [ 1 ] + [MASTER CODE] + [MM] [DD] [YY]

Set Time

[ Q ] + [ 6 ] + [ 2 ] + [MASTER CODE] + [H][H] [M][M]

*Set Auto Arm Time

[ Q ] + [ 6 ] + [ 3 ] + [MASTER CODE] + [H][H] [M][M]

Set Follow-Me Phone No. 1

[ Q ] + [ 7 ] + [ 1 ] + [MASTER CODE] + Phone No. + [ #]

Set Follow-Me Phone No. 2

[ Q ] + [ 7 ] + [ 2 ] + [MASTER CODE] + Phone No. + [ #]

**Set Follow-Me Phone No. 3

[ Q ] + [ 7 ] + [ 3 ] + [MASTER CODE] + Phone No. + [ #]

**Set Follow-Me Phone No. 4

[ Q ] + [ 7 ] + [ 4 ] + [MASTER CODE] + Phone No. + [ #]

Maintenance:

 

 

 

On/Off Buzzer

[ Q ] + [ 8 ] + [MASTER CODE] + [1]

On/Off Door Chime

[ Q ] + [ 8 ] + [MASTER CODE] + [ 2]

*On/Off Audible Kiss-Off

[ Q ] + [ 8 ] + [MASTER CODE] + [ 3]

Indication

 

 

 

Get Event From Event

[ Q ] + [ 9 ] + [MASTER CODE] + [EVENT NO.]

Logger

 

 

 

Test System

[ Q ] + [ 0 ] + [MASTER CODE]

 

 

 

 

 

 

 

 

 

LED

Trouble

 

 

 

 

1

Low Battery

 

 

Trouble Table

 

2

AC Power Loss

 

 

 

3

Clock Not Set

 

 

 

 

 

 

 

 

4

Communication Trouble

 

 

 

 

5

Bell Loop Trouble

 

*New in Version 1.2

 

 

 

**New in Version 1.3

 

 

 

4

Installer Manual

TABLE OF CONTENTS

Introduction to the ORBIT-6..................................................................

6

Main Features:..................................................................................

6

Installation............................................................................................

7

Before You Begin..............................................................................

7

Technical Data .....................................................................................

8

Installer Programming ..........................................................................

9

The keypad.......................................................................................

9

Restoring Factory Defaults to the ORBIT-6 .......................................

9

Introduction to Programming .............................................................

9

Programming your Orbit-6...............................................................

10

Viewing the Contents of a Location .................................................

11

Locations Whose Contents Occupy More Than One Digit ...............

12

Audible Tones and Error Beeps ......................................................

12

How to program installer parameters...............................................

12

A Programming Tutorial ..................................................................

12

GENERAL SYSTEM PARAMETERS: Locations 00–05 ....................

14

SYSTEM CODES: Locations 06-10 ..................................................

15

SYSTEM TIME: Locations 11-13 ......................................................

16

Intrusion Zone Types and Zone Sounds: Locations 14-21..................

16

SPECIAL ZONE TYPES:....................................................................

18

Utility Outputs: Locations 22-25 ........................................................

19

Communication Parameters: Locations 20–21....................................

22

Digital Communicator Controls: Location 26....................................

22

Central Station Protocols: Location 27-28......................................

23

Understanding the Code Format .....................................................

24

Upload/Download Rings: Location 29............................................

25

System Controls: Location 30 ...........................................................

25

Periodic Test Time: Location 31 .......................................................

27

Communicator Reporting Codes: Locations 32 through 85.................

27

5

Installer Manual

INTRODUCTION TO THE ORBIT-6

The ORBIT-6 is intended to address the needs of many homes, offices, and small businesses. Its operation is designed around microprocessor and EEPROM (Electrically Erasable Programmable Read-Only Memory) technology, which stores, without the need for a source of power, the system’s operating program and its programmable parameters.

System programming may be performed from any ORBIT-6 keypad, or from a special LCD Programming Keypad designed specifically for that.

Remote and local system programming is also possible through the use of Rokonet’s ORBIT Upload/Download software.

Main Features:

Zones (end-of-line resistor required 2200 ohm)

6 Programmable Intrusion Zones

Special type: Zone 5 – Fire Zone, Zone 6 - tamper zone

One Fixed Panic Zone input on the keypad (not on keypad RP206KL6)

3 Keypad Emergency Zones (Panic, Fire, Special Emergency)

Alarm Sounder Output

Programmable Bell/Siren or Loudspeaker Output

Capacity: 750 mA (maximum)

Auxiliary Output for Peripheral Devices

Capacity 250 mA (maximum)

Built-In Digital Communicator

For Central Station communications (two phone numbers)

For Upload/Download functions

For follow-me functions

Keypads

Up to 4 LED/LCD keypads can be connected

Utility Outputs

One transistor-driven (open-collector) triggered output

Security Codes

Two Installer Codes

One Master (User) Code

Nine User Codes (all may be used as duress code)

Periodic Testing

Daily test report to central station

Optional Peripherals

Four relay outputs expansion

Voice Module

Event Log

Event log of 100 events

6

Installer Manual

INSTALLATION

Before You Begin

Be sure the actual work is performed by experienced personnel, licensed to carry out security system installations and capable of implementing all applicable requirements of the National Fire Protection Association (NFPA-70 and NFPA-74), as well as any federal, state, and local codes–along with any safety guidelines and regulations which might apply.

Mounting and Wiring the Control Panel (refer to figures 1A, 1B & 1C on pages

32, 33 & 34)

1.Mount the ORBIT-6’s metal cabinet at a protected dry location, near a source of unswitched AC Power, a good ground, and access to telephone service. Use the proper hardware (e.g. anchors, mollys, toggle bolts, etc.), as required, to insure a suitable mounting.

2.Thread all electrical wiring through a convenient hole in the metal cabinet. To prevent potential damage, be sure that live AC power is NOT present and that the Standby Battery is NOT connected. Refer to Figures 1A and 1B. Your wiring may include any and all of the following:

connections to Hardwired Zones

connections to devices requiring Uninterrupted Auxiliary Power (e.g. PIRs, Glass Break Detectors)

connections to Smoke Detectors requiring Resettable Power

connections to any External Sounders

3.If using Utility Output, connect the UO/ECL output, this terminal is designed to activate a low current device (e.g. a 12 VDC Relay, drawing no more than 70 mA).

If using UO expansion module, connect the UO/ECL terminal to the ECL terminal input in the expansion module. In this case the first UO on the expansion module will become UO1. (see figures A1)

4.Make connections from the RJ31X (or equivalent) telephone company interface.

5.Make connections to the system’s keypad(s) by the correspnding wire colors.

6.Make connections to AC Power (via a 16.5 VAC, 25 VA transformer). Do not plug in the transformer at this time.

7.Have a Standby Battery ready (typically 12 VDC, 4 AH), but do not connect it at this time.

8.All zone inputs are End Of Line supervised, use 2200 ohm resistors (supplied).

9.When using 8 LED keypad, zones 7 & 8 are end-of-line supervised. Use 2200 ohm resisters (supplied) when the zones are not in use. For further wiring instructions of the 8 LED keypad, refer to Figure 1C on page 34.

10.If using a Key-switch, use a momentary key-switch. The receiver (if used) must give a pulse output and not on/off.

11.To connect the panic button use the white wire as (+) and the black wire as (-).

Note: The maximum distance between the panic button and the keypad is 30 meters.

7

Installer Manual

TECHNICAL DATA

Main Panel

Input power

16.5 V AC 25 VA via transformer

Rechargeable standby battery

12

V 4 A-Hours

 

Auxiliary Power

12

V DC 250 mA maximum

 

Bell/LS Sounder output

12

V DC 750mA maximum

 

Programmable output

Open collector Active pull down 70mA maximum

Cabinet Dimensions:

260X218X83 mm (10.2X5.1X3.3 “)

Weight

1.84 kg (4 lb)

 

Main Board (dimensions / weight):

80X167 mm (3.15X6.6 “)

0.17 kg (0.37lb)

Fuse F1

Auxiliary Power

0.5 A

Fuse F2

Bell/LS Power

1 A

Fuse F3

Battery Power

2 A

Keypads

 

6-Zone Keypad

8-Zone Keypad

Current consumption:

18 mA typical, 30 mA maximum

18 mA typical, 30 mA maximum

Control panel

4-wire up to 300 ft (100 m) from

4-wire up to 300 ft (100 m) from

connections:

panel

panel

Dimensions:

110X130X25 mm (4.3X5.1X1 “)

110X130X25 mm (4.3X5.1X1 “)

Weight:

0.19 kg (0.42 lb)

0.19 kg (0.42 lb)

Utility Output Expansion Module

 

Relay

Transistor

Current consumption:

10mA typical, 50mA max

10mA typical, 15mA max

Control panel connections:

4-wire up to 300 ft (100m) from panel

Contacts:

4 relays, 0.5 A, 24 V DC

4 O.C., 50 mA, 12 V DC

Dimensions:

53X85 mm (2.1X3.35 “)

Weight:

80 gr (0.18 lb)

Max. Run Length from Panel to Keypad

Wire

AWG

19

20

22

 

Ø (mm)

0.9

0.8

0.6

Length

Meter

200

166

100

 

Feet

660

547

330

Bell Loudspeaker Wiring Table (Distance in Feet)

 

AWG

18

 

19

20

 

 

22

Max.

Ø mm

1

 

0.9

0.8

 

 

0.6

Feet

Meter

Feet

Meter

Feet

Meter

Feet

Meter

Current mA

 

 

 

 

 

 

 

 

100

780

238

625

190

495

151

310

95

300

260

79

208

64

165

50

103

32

650

120

37

96

30

76

23

48

15

Detectors Distance in Feet

AWG

 

18

 

19

 

20

 

22

 

24

Ø mm

 

1

 

0.9

 

0.8

 

0.6

 

0.5

Max.

Feet

Meter

Feet

Meter

Feet

Meter

Feet

Meter

Feet

Meter

Current mA

 

 

 

 

 

 

 

 

 

 

20

3920

1195

3100

945

2460

750

2460

472

1550

296

30

2600

793

2060

628

1640

500

1640

314

1030

197

40

1960

597

1550

472

1230

375

1230

236

775

148

8

Installer Manual

INSTALLER PROGRAMMING

The keypad

The Orbit-6 can support up to 4 keypads, with a choice of 3 styles, 1 LCD type and two LED types from which virtually all features may be accessed. In addition to the functions it provides for the user, each of the keypads can be used by an installer to program the system parameters.

An attempt to enter an incorrect series of keystrokes will result with 3 error beeps.

All program location values (data) are displayed by zone indicators on the LED keypad in binary format.

Restoring Factory Defaults to the ORBIT-6

1.Your ORBIT-6 and at least one LED Keypad should already be wired together and/or physically installed

2.Remove all power from the Printed Circuit

3.Place the ORBIT-6’s J1 (DEFAULT) jumper over both corresponding pins. (See Figures 1A and 1B on page 32 and 33 ).

4.Reapply power (AC and/or Standby Battery) to the PC Board.

5.After a short beep is heard, remove the J1 jumper. The ORBIT-6’s default settings are now restored.

6.Check that the POWER LED is flashing. Depending on the state of the system, the READY LED and the Zone LEDs may or may not be lit.

Introduction to Programming

First, check that the panel’s J1 (DEFAULT) jumper is NOT covering both pins on the PC Board.

The ORBIT-6 stores information in 86 programming locations.

The data stored in any location is represented by numbers and/or letters. Some locations require just one digit, while most require two. Others (e.g. those used to store phone numbers and account numbers) may require several more digits.

It is not necessary to enter data into all 86 categories. Many locations have been factory-programmed with default parameters.

Note that power can be removed from the ORBIT-6, as its memory does not require a source of power to retain its information.

9

Installer Manual

Programming your Orbit-6

Programming Methods

Local

Requirements

LED or LCD keypads

The keypad must be wired to the Orbit-

 

 

6 panel.

 

Power must be applied to the Orbit-6.

Orbit Programmer

 

Easy programming of the control panel

The programmer will be connected and

parameters with menu driven LCD

receive its power from the panel.

display.

 

The programmer can store up to 10

 

Orbit-6 programming sets and copy it

 

directly to the panel. The programmer

 

supports both the Orbit-5 and Orbit-6

 

panels.

 

Orbit UD*

 

Local Up/Load Windows version from a

The software must be installed and an

personal computer.

Orbit UD Adaptor cable is connected

 

between the panel and the computer.

Remote

Requirements

Orbit UD*

 

Remote U/D Windows version from a

The software and applicable modem

personal computer.

with configured access to a telephone

 

line must be installed.

* Compatible with Windows 95/98/2000 & NT.

10

Installer Manual

Viewing the Contents of a Location

It’s often necessary to check the data stored in a memory location to be sure it’s correct. If improper data is found, it must be corrected in order to obtain the desired system response. The data in a location can either be a number (from 0-9) or a letter (from A-F). Doing so takes advantage of the hexadecimal numbering system. For our purposes, the characters A through F will be referred to as hexadecimal digits.

Whenever the Installer Programming mode is active, the first 4 keypad’s Zone LEDs (1-4) are used to reveal each digit in a selected location. By adding up the values assigned to the lit LEDs, the contents of any location can be determined. See table below.

ZONE LEDs

 

ZONE LEDs

I.D.:

4

3

2

1

Value:

8

4

2

1

 

 

 

 

 

0

off

off

off

off

1

off

off

off

ON

2

off

off

ON

off

3

off

off

ON

ON

4

off

ON

off

off

5

off

ON

off

ON

6

off

ON

ON

off

7

off

ON

ON

ON

I.D.:

4

3

2

1

value:

8

4

2

1

 

 

 

 

 

8

ON

off

off

off

9

ON

off

off

ON

A

ON

off

ON

off

B

ON

off

ON

ON

C

ON

ON

off

off

D

ON

ON

off

ON

E

ON

ON

ON

off

F

ON

ON

ON

ON

EXAMPLE:

Zone 4-ON Zone 3-off

Zone 2-off Zone 1-ON

TOTAL = 9

EXAMPLE:

Zone 4-ON Zone 3-off

Zone 2-ON Zone 1-ON

TOTAL = B

Hexadecimal Digits

In some locations you may be required to enter hexadecimal digits A - F to do so see the next table.

“A” is entered by pressing [STAY] + [1] “B” is entered by pressing [STAY] + [2] “C” is entered by pressing [STAY] + [3] “D” is entered by pressing [STAY] + [4] “E” is entered by pressing [STAY] + [5] “F” is entered by pressing [STAY] + [6]

11

Installer Manual

Locations Whose Contents Occupy More Than One Digit

When a location contains more than one digit, they cannot be viewed simultaneously. As soon as a location is accessed, the first digit is displayed automatically. Additional digits (if they exist) can be displayed by pressing the following keys:

Used to display the next digit in a location containing at least two digits; e.g. if 5-6-7-8 is stored in a location, the “5” is displayed first; by pressing , the “6” will be displayed; continue this

process to display the entire contents of the chosen location. Error beeps will be produced when it’s attempted to display digits which don’t exist

Used to move backwards among the digits stored in a location containing at least two digits. Error beeps will be produced when it’s attempted to display digits which don’t exist

Audible Tones and Error Beeps

To confirm an operation, a single, long beep will be heard. However, any improper use of the keypad resulting in an error or an unacceptable response will produce three rapid beeps. If heard, repeat the operation or exit the programming mode and try again.

How to program installer parameters

1.To enter the Installer programming mode:

Press 4 digit Installer code followed by # (factory default 0 2 0 6)

2.To move to a new location:

Press two digits of location followed by ARM

3.To enter data into the location:

Press data digits (0 - 9 digits including hexadecimal A-F) followed by #

4.To exit programming mode:

Press 4 digit installer code followed by ARM

A Programming Tutorial

To get acquainted with some programming basics, a short tutorial has been prepared. It involves changing the Installer Code from the factory default of 0-2-0- 6 to a sequence of your own choosing. If you can master this operation, subsequent programming should be easy.

12

Installer Manual

 

Operation

Action

Comments

 

 

1

Enter the

enter the factory default

a long beep will sound, confirming

 

Installer

Installer Code (0-2-0-6);

successful entry into Installer

 

 

Programming

followed by #

Programming

 

 

 

mode

 

 

 

 

 

2

Access the

press [0], [8], [ARM]

no confirming beep will sound

 

 

current Installer

 

 

 

 

 

 

Code

 

 

 

 

 

 

(stored in location

 

 

 

 

 

 

“08”)

 

 

 

 

 

3

Enter a unique

enter [3], [0], [5], [7]

no confirming beep will sound

 

 

Installer Code

 

 

 

 

 

 

(for this tutorial,

 

 

 

 

 

 

we’ll use 3-0-5-7)

 

 

 

 

 

4

Store the data

press [#]

a long beep will sound confirming that

 

you have entered

 

data has been properly stored

 

 

 

 

if a wrong number of digits entered

 

 

 

three (error) beeps will sound after

 

 

 

pressing #

 

 

 

5

Check the data

the first digit of the stored

press

displayed

zone

value

 

stored in Location

data will appear

keys

 

LEDs

 

 

“08”

observe the Zone LEDs

 

 

lit

 

 

 

press [STAY] [STAY] to

none

1st digit

2, 1

3

 

 

advance to the next digit

 

 

 

 

 

 

once all four digits have

STAY

2nd digit

none

0

 

 

been displayed, attempts to

 

 

STAY

 

 

 

 

 

view an additional digit will

 

 

 

 

 

 

STAY

3rd digit

 

 

 

 

result in three (error) beeps

3,1

5

 

 

if desired, press [STAY]

STAY

 

 

 

 

 

STAY

 

 

 

 

 

and [ARM] to move

4th digit

3,2,1

7

 

 

backwards

STAY

 

 

 

 

 

 

 

6

Go to another

press the desired two-digit

press [ARM] alone to go to the next

 

location of your

location and [ARM]

sequential location

 

 

 

choice

 

 

 

 

 

7

Exit

enter your Installer Code

a long beep will confirm your actions

 

programming

and press [ARM]

 

 

 

 

13

Installer Manual

GENERAL SYSTEM PARAMETERS: LOCATIONS 00–05

Location: 00 Default Enable: Def: 00

PURPOSE: to enable or disable the option of resetting the system to the factory defaults.

00

Enable the option of resetting the system to the factory defaults.

55

Disable the option of resetting the system to the factory defaults.

Location: 01 MS Lock: Def: 000000

§MS Lock is a 6-digit security code used in conjunction with Rokonet’s Upload/Download Software

§It is designed to provide greater proprietary security to the Central Station parameters

§It is NOT necessary to change the MS Lock default value within Installer Programming; instead, the procedure may be performed from the Upload/Download Software and then downloaded to the ORBIT-6

for additional information, refer to the Upload/Download Programming Manual

Location: 02 Phone Number: Primary Central Station (Central Station 1)

To delete an existing phone number, simply press the [#] key; to enter or replace the phone number required to reach the primary Central Station include all access digits (e.g. 0 to 9) and the area code. If required, include the following special functions to achieve the effect listed in the table:

FUNCTION

SEQUENCE

RESULTS

stop dialing and wait for a new dial tone

[STAY],

[1]

A

wait a fixed period before continuing

[STAY],

[2]

B

switch from Pulse to Tone (or from Tone to Pulse)

[STAY],

[3]

C

send the DTMF Q character

[STAY], [ * ]

*

 

send the DTMF # character

[STAY],

[#]

#

When done with your complete entry, press [#] to store it. Up to 24 digits can be entered to the phone number.

For your records, enter the complete phone number below:

Location: 03 Phone Number: Secondary Central Station (Central Station 2)

Same as in Location 02

14

Installer Manual

Installer Code
Remote ID
Access Code

Location: 04 Callback UD Phone #

Enables greater security for remote Upload/Download operation. This is a number to which the alarm company computer, equipped with the U/D software, will be connected.

When a call is made from a computer, using U/D software, to the Orbit-6 panel, the system will hang-up and call back using this UD phone number. Up to 24 digits can be entered into the U/D phone number, include all the digits and functions as above in Location 02. To delete an existing phone number press #.

Location: 05

Account Number

Default: 0000

PURPOSE: to assign the system’s Central Station Account Number

hexadecimal account numbers (those using 0 through 9 and A through F) are accepted by the ORBIT-6; use the key combinations below to enter hexadecimal digits “A” through “F”:

hex digit

press

 

hex digit

press

 

Acct No.

A

[STAY], 1

 

D

[STAY], 4

 

 

 

 

 

 

 

 

 

 

 

B

[STAY], 2

 

E

[STAY], 5

 

 

 

 

 

 

 

 

 

 

 

C

[STAY], 3

 

F

[STAY], 6

 

 

 

 

 

“0” will not send a digit to the central station, to send “0” use “A” digit

SYSTEM CODES: LOCATIONS 06-10

Location: 06

Access Code

Default: 5678

PURPOSE: to provide data security during Upload/Download operations

this same Access Code must subsequently be entered into the corresponding account profile in the Upload/Download software (along with the Remote ID codes, see Location 07, below).

Location: 07

Remote ID Code

Default: 0001

PURPOSE: to provide data security during Upload/Download operations this same Remote ID Code must subsequently be entered into the corresponding account profile in the Upload/Download software.

Location: 08

Installer Code I

Default: 0206

PURPOSE: the installer code is used by alarm company personnel authorized to modify the system’s parameters It is recommended to change the “factory default” Installer Code to one of your own choice.

15

Installer Manual

Sounder
Cutoff
Entry Delay
Exit Delay
Master Code
Installer Code

Location: 09

Installer Code II

Default: 1206

Same as the Installer Code 1, but with a few limitations: It can't modify the "default code", observe and modify the first installer's codes, modify any MS phone number, nor observe & modify MS lock code.

Location: 10

Master Code

Default: 1234

PURPOSE: to establish the keypad code for the system’s “chief user”; the Master Code provides the following special privileges:

to enter, modify, and delete the remaining nine User Codes

to set the system's internal clock

to perform certain system functions and tests

Note: the Master Code cannot be seen by the installer through the zone LEDs on the keypad.

SYSTEM TIME: LOCATIONS 11-13

Location: 11

Exit Delay

Default: 030

PURPOSE: to establish the system’s Exit Delay (the interval, in seconds, between entering a User Code at the keypad and when the system actually arms).

Enter three digits between 001 and 255 seconds

Location: 12

Entry Delay

Default: 060

PURPOSE: to establish the system’s Entry Delay (in an armed system, the interval, in seconds, between the moment an entry door is opened and an alarm is triggered). Enter three digits between 001 and 255 seconds

Location: 13

Bell Cutoff Time

Default: 04

PURPOSE: to set the interval that the system’s external sounder(s) will operate before it shuts off automatically.

Enter the number of minutes between 01 and 90

INTRUSION ZONE TYPES AND ZONE SOUNDS: LOCATIONS 14-21

Locations 14 through 21 are identical and are corresponding to Zones 1 through 6 or 8 (in the 8-zone keypad), respectively. Each of these locations contains two digits.

the first digit: Contains the number used to represent the Type of Zone desired

the second digit: Contains the number used to represent the sound produced

when in alarm

Note: 1. When using 6 zone keypad the system disregards zones 7 - 8.

2.When using 8 zone keypad, zones 7 - 8 must be connected to an EOL resister when not in use.

16

Installer Manual

Locations: 14-21

Zone 1-8: (1st Digit): Type

Default:

1st Digit

 

Zone Type and Comments

0

Not Used

 

 

All unused zones should be given this designation. It is also used to disable a zone

 

1

24-Hour

 

 

A violation of such a zone will always cause an instant intrusion alarm, regardless of

 

the system’s armed/disarmed state

 

2

Instant (Intrusion)

 

Causes an immediate intrusion alarm if violated when the system is in arm state. Entry

 

Delay.

 

 

3

Entry/Exit Delay

 

 

If violated, a zone with this designation will not cause an intrusion alarm during the

 

Entry and Exit Delay periods

 

 

Exit (OPEN)/Entry

 

4

Such a zone behaves as described above in Entry/Exit Delay, except that if faulted at

the time the system is armed, it will be bypassed and NOT prevent system arming.

 

To avoid an intrusion alarm, however, it must be secured before the expiration of the

 

Exit Delay period (Location 11).

 

 

Entry Follower

 

 

5A zone(s) given this designation will cause an immediate intrusion alarm when violated unless an Entry/Exit zone was violated first if so, an Entry Follower zone(s) will remain bypassed until the end of the Entry Delay period

Interior + Entry Delay Follower

If the system is armed to AWAY (ARM) mode: this type of zone behaves like the Entry Follower, described above

6If the system is armed to the STAY mode: this type of zone will be bypassed Important Note: When arming with "STAY" mode it is possible for the user to eliminate the entry delay period by pressing the (STAY) key twice in succession when arming the system.

Fire Zone

Intended for smoke or other types of fire detectors. If violated, will cause an immediate

7fire alarm. Only Zone 5 can be programmed as a fire zone. A fault in the wiring of any fire zone, if supervised, will cause a fire alarm, manifested by a rapid flushing of the keypads' Fire LED.

Tamper Zone

8Only Zone 6 can be a Tamper Zone. It operates the same as 24 hours Zone, but this type has a special reporting code.

9Panic Zone

If violated an immediate panic alarm will be announced.

Key-switch Zone - Instant

AIf desired for system arming and disarming an external SPST spring - loaded, normally open, momentary type key switch can be added. The key switch permits an instant arm and disarming of the system after tripping.

Key-switch Zone - Delayed

BSuch a zone behaves as described above in "key switch zone instant", except when arming the system an exit delay will follow.

Latch-Key-switch Zone – Instant: If desired for system arming/disarming, connect **C an external SPST latching type (non-momentary) key-switch to any zone terminals,

given this designation.

Latch-Key-switch Zone – Delayed: Such a zone behaves as described above in **D "latched key switch zone instant", except when arming the system an exit delay will

follow.

** New in Version 1.3

17

Installer Manual

Locations: 14-21

Zone 1-8: (2nd Digit): Sound

Default:

2nd Digit

Zone Sound and Comments

 

0

Silent

 

 

a violation during the armed period will produce no sound

 

the resulting alarm can still be reported to the Central Station

External Sounder (Continuous)

1 causes the external sounding device to annunciate steadily, without breaks in the (default) sound cadence the sound will continue until the sounder “times out” or the system is

disarmed

External Sounder (Pulses)

2causes the external sounding device to produce a pulsed (or staggered) annunciation this sound is usually recommended for fire alarm annunciation

3Keypad Sounder Only

causes the piezo sounder within the system’s keypad(s) (only) to beep rapidly

External Sounder + Keypad Sounder

4causes the external sounding device to annunciate continuously, without breaks in the sound cadence causes the piezo sounder within the system’s keypad(s) to beep rapidly

External Sounder When Armed / Keypad Sounder When Disarmed

5related to 24H zones

when alarm during disarm, the keypad’s buzzer will be activated

when alarm during armed system, the external sounder will be activated

Door Chime

assigned to an opening which, when violated during the disarmed period, will cause the

6system’s keypad(s) to beep once during an alarm, the external sounding device will annunciate continuously, without interruption. When alarm occurs during armed system only the external sounder will be activated.

Zone

Location

Type

Sound

Z1

14

(3)

(1)

Z2

15

(5)

(1)

Z3

16

(2)

(1)

Z4

17

(6)

(1)

Z5

18

(2)

(1)

Z6

19

(2)

(1)

Z7

20

(0)

(0)

Z8

21

(0)

(0)

* (x) define the type and sound default

SPECIAL ZONE TYPES:

Location: 18 Zone 5: Fire Zone

Zone 5 is reserved as a Fire Zone, supports four-wire Smoke Detectors. Smoke Detector power must be interruptible in order to reset a detector “latched” in alarm. As such it should be derived from the UO/ECL or one of the UOs terminal (see Figures 1A and 1B). The related UO should be defined as AUX power switch.

Location: 18

Zone 5: (1st Digit): Type

Default: Fire

1st Digit

Zone Type and Comments

 

Fire

7A fire zone cannot be disabled or bypassed.

A fault in the wiring to the zone will cause a Fire Trouble (fire LED blinks). A short in the zone wiring will cause a fire alarm.

18

Installer Manual

Location: 18

Zone 5: (2nd Digit): Sound

Default: External Sounder (Pulses)

For fire zone the recommended (default) zone sound is “External sounder pulsed” However it is possible to change the zone sound and type to any of the ones provided in the previous list.

Location: 19 Zone 6: Tamper Zone

Zone 6 is reserved as a Tamper Zone. This zone can be programmed to any zone type (except Fire) including Tamper. If the zone was programmed as Tamper, in violation, a Tamper Code report will be sent and the Tamper LED on the keypad (marked as 6/Tmp) will light up.

UTILITY OUTPUTS: LOCATIONS 22-25

The ORBIT-6 supports one open collector Utility Output (derived between the UO/ECL and AUX terminals) which can be used for switching an external device on or off. Once the Utility Output is activated the device will be connected between AUX (+12V) and ground (0V). This connection is capable of switching light loads of no more than 70mA.

Note: When activated the utility output is switched to the Negative Polarity.

The “UO” can be also used to reset a “latched” Smoke Detector(s). In that case the 12V power to the smoke detector will be supplied via the UO (see Figures 1A and 1B). The UO should be defined as AUX switch.

If the Utility Output Expansion Module is being used, the same information in Location 22 is applicable for the programming of UO2 (Location 23), UO3 (Location 24), and/or UO4 (Location 25). It is not necessary to program all of the available “UOs”, unless they’re used. Note that when the Utility Output Expansion Module is employed, the original Utility Output on the Main Board (the UO/ECL terminal) is no longer available.

Important: In order to use the Utility Output Expansion you have to define the module in Location 30.

22

If more than one “UO” output is necessary, a

Utility Output Expansion Module is available. Its four “UOs” (U01, UO2, UO3, and UO4) replace the ORBIT-6’s single “on-board ”UO”. The “UOs” on the Utility Output Expansion Module are relay-based, and allow a maximum current of 500 mAs. Refer to Figures 1A and 1B (pages 32 and 33), for wiring instructions and additional information. The figure at the right, shows how a Utility Output on the “UO Expander” can be used to switch a table lamp on and off.

Because of the “UO’s” modest 70 mA current capability, it will be necessary to use an “intermediate” relay-whose physical contacts can switch far greater currents (limited by their contact rating). The figure at the left shows how such a relay can trigger a strobe light. If used in this manner, the “UO”cannot be used to reset a “latched” Smoke Detector(s).

23)

16.

19

Installer Manual

Digit Event and Result

00 Not Active

(default) UO offers no response to any system activity

Arm Follow (Latch)

01U0 is activated when the system is armed. The activation occurs after the expiration of the exit/delay period. The U0 remains active (latched) while the system is armed. When disarming the system the U0 deactivates (unlatches).

 

Arm Follow (Pulse)

02

UO is activated when the system is armed. The activation occurs after the expiration of

the exit/delay period. The UO is activated for several seconds (pulse), after which is

 

 

deactivated.

Alarm Follow (Latched)

UO is immediately activated when the system goes into any type of alarm (i.e. intrusion, 03 fire, keypad-initiated panic) UO remains active (latched) for the duration of the

alarm-even after the system’s sounder “times out” UO is deactivated when the system is disarmed

04

Alarm Follow (Pulse)

UO is immediately activated for several seconds and then deactivated whenever the

 

system goes into any type of alarm (i.e. intrusion, fire, keypad-initiated panic)

 

Zone 1 Alarm Follow (Latched)

05

U0 is immediately activated when an alarm occurs on Zone 1. U0 remains active

(latched) for the duration of the alarm - even after the system sounder "times out". U0 is

 

 

deactivated when Zone 1 goes into normal condition.

06

Zone 1 Alarm Follow (Pulsed)

U0 is immediately activated for several seconds (pulsed) and then deactivates whenever

 

Zone 1 goes into alarm.

07

Zone 2 Alarm Follow (Latched)

08

Zone 2 Alarm Follow (Pulsed)

09

Zone 3 Alarm Follow (Latched)

0A

Zone 3 Alarm Follow (Pulsed)

0B

Zone 4 Alarm Follow (Latched)

0C

Zone 4 Alarm Follow (Pulsed)

0D

Zone 5 Alarm Follow (Latched)

0E

Zone 5 Alarm Follow (Pulsed)

0F

Zone 6 Alarm Follow (Latched)

10

Zone 6 Alarm Follow (Pulsed)

11

Zone 7 Alarm Follow (Latched)

12

Zone 7 Alarm Follow (Pulsed)

13

Zone 8 Alarm Follow (Latched)

14

Zone 8 Alarm Follow (Pulsed)

 

Panic Follow (Latched)

15UO is activated immediately when a PANIC alarm is triggered by a violation of a zone, defined as Panic, or by pressing the keypad’s [1] and [2] keys simultaneously for two seconds. U0 is deactivated when the system is disarmed.

Panic Follow (Pulse)

16UO is activated for several seconds when a PANIC alarm is triggered by a violation of a zone, defined as Panic, or by pressing the keypad’s [1] and [2] keys simultaneously for two seconds.

20

Installer Manual

Special Emergency Keying Follow (Latched)

17UO is activated immediately when pressing the keypad’s [7] and [8] keys simultaneously for two seconds. U0 is deactivated when the system is disarmed.

Special Emergency Keying Follow (Pulsed)

18UO is activated for several seconds when pressing the keypad’s [7] and [8] keys simultaneously for two seconds.

Fire Keying Follow (Latched)

19UO is activated immediately when a Fire alarm is triggered by a violation of zone 5, defined as Fire, or by pressing the keypad’s [4] and [5] keys simultaneously for two seconds. U0 is deactivated when the system is disarmed.

1A

Fire Keying Follow (Pulse)

UO is activated when a Fire alarm is triggered by a violation of zone 5, defined as Fire,

 

or by pressing the keypad’s [4] and [5] keys simultaneously for two seconds.

 

User Activated (Toggle)

 

UO may be activated by the user through the entry of [*]+[2]+[User Code]+[X], where X

1B

refers to the utility output number.

The first entry of the above sequence activates the UO and causes it to latch in the

 

opposite of its current state. The system briefly lights the Zone LED corresponding to the

 

selected UO and produces a single confirming beep subsequent entries toggle the

 

response from ON to OFF to ON, etc.

 

User Activated (Pulse)

 

UO may be activated by the user through the entry of [*]+[2]+[User Code]+[X], where X

1C

refers to the utility output number.

 

The entry activates the UO for several seconds (pulse). The system briefly lights the

 

Zone LED corresponding to the selected UO and produces a single confirming beep

 

subsequent entries repeat this pattern.

 

AUX POWER Switch (Fire)

 

Until triggered, UO is normally activated and is designed to be a part of the circuit

 

supplying power to the Smoke Detector(s); see Figure 1A and 1B.

 

After a Fire Alarm is disarmed, it may be necessary to reset any Smoke Detector(s)

1D

which may be “latched” in alarm. A “latched” Smoke Detector will cause the keyboard’s

FIRE LED to remain lit, even though the panel may be disarmed. To reset a Smoke

 

Detector, a “UO” used in this manner must be momentarily deactivated; this action is

 

performed by the user, who must enter [*]+[2]+[User Code]+[X], where [X] refers to the

 

UO number (i.e. 1,2,3, or 4) in the circuit providing Smoke Detector power. If this is not

 

done, it will be impossible to arm the panel; please advise your customer of this

 

contingency which is stated in the ORBIT-6’s User Manual.

 

Duress Code Follow (Pulse)

1E U0 is activated for several seconds (and then deactivates) when any duress code is

 

entered.

1F

AC Loss Follow (Latched)

U0 is activated due to a lack of power from the commercial AC. U0 is deactivated when

 

the system is operating properly from commercial (AC) power.

AC Loss Follow (Pulse)

20U0 is activated for several seconds (and then deactivates) due to a lack of power from the commercial AC.

Low Battery Follow (Latched)

21U0 is activated due to low power from the backup battery. U01 is deactivated when the battery is in good condition.

22Low Battery Follow (Pulse)

U0 is activated for several seconds due to low power from the backup battery.

Voice Module Enable

23The U0 is activated after FM phone number dialing has been made due to alarm. The U0 deactivates after the FM period termination.

21

Installer Manual

Duress Code Follow (Latched)

24UO is activated when any duress code is entered. The UO deactivates either when arming the system or disarming the system due to an alarm that was activated from the emergecy keypad keys, 24-hour zone violation or tamper zone violation.

25

Follow Chime (Pulse) (Ver. 1.2) UO is activated for several seconds whenever a

keypad sounds its chime.

 

26

Follow Bell Latched NO (Ver. 1.2) UO is activated whenever the bell is activated. UO

is deactivated at the bell cut-off time.

 

27Follow Bell Latched NC (Ver.1.3)

28Follow Ready NO (Ver.1.3) UO is activated whenever the system is in the ready state.

Locations: 22

23

24

25

 

UO1

 

UO2

 

UO3

 

UO4

 

Action

 

Action

 

Action

 

Action

 

 

 

 

 

 

 

 

 

 

 

 

COMMUNICATION PARAMETERS: LOCATIONS 26–29

Locations 26 and 27 allow you to define the manner in which the ORBIT-6 communicates with the Central Station when it reports alarms, restorals, troubles, openings/closings, and tests.

Digital Communicator Controls: Location 26

First digit: determines the number (or hexadecimal digit) corresponding to the Dialing Method / Duty Cycle / Redial Time desired

Second digit: determines the number corresponding to the Attempts / Answering Machine Use / UL Installation

Attempts

Answering Machine

UL Installation

 

 

Voice Module

 

in Use

 

 

 

 

 

 

Attempts sets the

If enabled to defeat an

 

If the ORBIT-6 is installed

 

If enabled (“YES”) voice

number of times the

answering machine, two

 

in accordance with UL

 

messages will be sent. If

ORBIT-6 will redial

phone calls must be

 

requirements, for a

 

 

“NO” then tones will be

the Central Station

made to the premises. On

Residential Installation

 

used to represent an active

after failing to

the first call let the phone

 

(UL 1641), the operation of

alarm.

establish a

ring once (by pushing the

the unit’s Digital

 

 

 

successful

space bar on the U/D

 

Communicator must be

 

 

communication.

software keyboard). The

 

modified so as to disable

 

 

 

panel detects this ring

 

features, which are

 

 

 

 

and starts a 60sec timer

 

inappropriate.

 

 

 

 

during which the panel

 

 

 

 

 

 

 

will answer the next call

 

 

 

 

 

 

 

on the first ring.

 

 

 

 

 

 

 

 

 

 

 

 

 

Location: 26

Dialer Controls: (1st Digit):

 

 

 

1st Digit

Dialing Method

 

Duty Cycle

 

* Redial Central Station

8

DTMF

 

 

N/A

 

 

after 60 seconds

1

Pulse @ 20 pps

 

 

67/33

 

 

after 30 seconds

9

Pulse @ 20 pps

 

 

67/33

 

 

after 60 seconds

4 (default)

DTMF

 

 

N/A

 

 

after 30 seconds

5

Pulse @ 20 pps

 

 

61/39

 

 

after 60 seconds

D

Pulse @ 20 pps

 

 

61/39

 

 

after 60 seconds

3

Pulse @ 10 pps

 

 

67/33

 

 

after 30 seconds

B

Pulse @ 10 pps

 

 

67/33

 

 

after 60 seconds

7

Pulse @ 10 pps

 

 

61/39

 

 

after 30 seconds

F

Pulse @ 10 pps

 

 

61/39

 

 

after 60 seconds

*redial refers to the number of seconds the ORBIT-6 will wait before redialing a busy or unresponsive Central Station phone number.

22

Installer Manual

 

Location: 26

Dialer Controls: (2nd Digit):

 

 

 

 

 

 

 

 

 

2nd Digit

 

Attempts

Answering Machine

 

UL Installation

 

Voice Module

 

 

0

 

3

 

No

 

 

No

 

No

 

 

 

1

 

8

 

No

 

 

No

 

No

 

 

 

2

 

3

 

Yes

 

 

No

 

No

 

 

 

3

 

8

 

Yes

 

 

No

 

No

 

 

 

(default)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

3

 

No

 

 

Yes

 

No

 

 

 

5

 

8

 

No

 

 

Yes

 

No

 

 

 

6

 

3

 

Yes

 

 

Yes

 

No

 

 

 

7

 

8

 

Yes

 

 

Yes

 

No

 

 

 

8

 

3

 

No

 

 

No

 

Yes

 

 

 

9

 

8

 

No

 

 

No

 

Yes

 

 

 

A

 

3

 

Yes

 

 

No

 

Yes

 

 

 

B

 

8

 

Yes

 

 

No

 

Yes

 

 

 

C

 

3

 

No

 

 

Yes

 

Yes

 

 

 

D

 

8

 

No

 

 

Yes

 

Yes

 

 

 

E

 

3

 

Yes

 

 

Yes

 

Yes

 

 

 

F

 

8

 

Yes

 

 

Yes

 

Yes

 

 

 

 

 

 

 

 

 

 

 

 

Central Station Protocols: Location 27-28

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Format Name

(PPS)

 

Kissoff/

Validation

 

InterDigit

 

Code

 

 

pulses/sec

Handshake

 

Time

 

format

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Silent Knight/

 

 

 

10

 

1400Hz

Dual round

 

650

 

0F

 

 

ADEMCO Slow

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Silent Knight/

 

 

 

10

 

1400Hz

Dual round

 

650

 

4F

 

 

ADEMCO Slow Extended

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Radionics/DCI/ Franklin slow

10

 

2300 Hz

Dual round

 

650

 

17

 

 

Silent Knight Fast

20

 

1400 Hz

Dual round

 

650

 

0E

 

 

Silent Knight Fast Extended

20

 

1400 Hz

Dual round

 

650

 

4E

 

 

 

 

 

 

 

 

 

 

 

 

 

Sescoa/Franklin/Vertix/ DCI fast

20

 

2300Hz

Dual round

 

650

 

16

 

 

Sescoa/Franklin/Vertix/DCI

20

 

2300Hz

Dual round

 

650

 

56

 

 

Extended

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Universal high speed

20

 

2300Hz

Dual round

 

390

 

12

 

 

Radionics

 

 

 

20

 

1400 Hz

Dual round

 

390

 

02

 

 

Radionics

 

 

 

20

 

2300Hz

Dual round

 

390

 

12

 

 

Radionics Extended

20

 

1400 Hz

Dual round

 

390

 

42

 

 

Radionics Extended

20

 

2300Hz

Dual round

 

390

 

52

 

 

Radionics

 

 

 

40

 

1400 Hz

Dual round

 

390

 

00

 

 

Radionics

 

 

 

40

 

2300Hz

Dual round

 

390

 

10

 

 

Radionics Extended

40

 

1400 Hz

Dual round

 

390

 

40

 

 

Radionics Extended

40

 

2300Hz

Dual round

 

390

 

50

 

 

Radionics

 

 

 

40

 

1400 Hz

Parity

 

390

 

20

 

 

Radionics

 

 

 

40

 

2300Hz

Parity

 

390

 

30

 

 

Radionics Extended

40

 

1400 Hz

Parity

 

390

 

60

 

 

Radionics Extended

40

 

2300Hz

Parity

 

390

 

70

 

Example: to use ADEMCO slow enter 0F to location 27

23

Installer Manual

Understanding the Code Format

To understand and modify the Code format according to a specific central station see the following

First digit: determine the number corresponding to the desired combination of: Kissoff/Handshake Freq / Message Validation / Extended–Non-Extended Format)

Second digit: determine the number (or letter) corresponding to the desired combination of: Dialing Rate / Interdigit Time / Data Frequency

Location: 27

 

CS Protocols: (1st Digit):

 

 

 

 

 

 

 

1st Digit

 

 

Format

Kissoff/Handshake Freq

Message Validation

0

 

Non-Extended

1400 Hz

Dual Round Compare

(default)

 

 

 

 

 

 

1

 

Non-Extended

2300 Hz

Dual Round Compare

2

 

Non-Extended

1400 Hz

Parity

3

 

Non-Extended

2300 Hz

Parity

4

 

 

Extended

1400 Hz

Dual Round Compare

5

 

 

Extended

2300 Hz

Dual Round Compare

6

 

 

Extended

1400 Hz

Parity

7

 

 

Extended

2300 Hz

Parity

 

 

 

 

 

 

Location: 27

 

CS Protocols: (2nd Digit):

 

 

 

 

 

 

2nd Digit

 

Data Rate

Interdigit Time

Data Frequency

0

 

40 pulses/sec

390 ms

1800 Hz

(default)

 

 

 

 

 

 

1

 

33 pulses/sec

390 ms

1800 Hz

2

 

20 pulses/sec

390 ms

1800 Hz

3

 

10 pulses/sec

390 ms

1800 Hz

4

 

40 pulses/sec

650 ms

1800 Hz

5

 

33 pulses/sec

650 ms

1800 Hz

6

 

20 pulses/sec

650 ms

1800 Hz

7

 

10 pulses/sec

650 ms

1800 Hz

8

 

40 pulses/sec

390 ms

1900 Hz

9

 

33 pulses/sec

390 ms

1900 Hz

A

 

20 pulses/sec

390 ms

1900 Hz

B

 

10 pulses/sec

390 ms

1900 Hz

C

 

40 pulses/sec

650 ms

1900 Hz

D

 

33 pulses/sec

650 ms

1900 Hz

E

 

20 pulses/sec

650 ms

1900 Hz

F

 

10 pulses/sec

650 ms

1900 Hz

24

Installer Manual

Location: 28

CS Protocols:

When selecting a contact ID & SIA format, all the reporting codes will be automatically applied to the locations of the reporting codes.

To change a code, enter a new code (according to the type of event – see page 30) to the corresponding location.

When selecting the Pulsed Protocol the default for all the reported codes will be “00” and any other code should be entered manually

To remove a particular reporting code from any of the 3 Protocols enter “00” into the corresponding location.

Important: Choose the code format only after defining the zone parameters. Changing a zone type after selecting the code format WILL NOT change the zone’s reporting code and a faulty report will be sent to the central station.

Digit

Format Name

Interdigit Time

Data Frequency

00

Pulsed Protocol

 

 

01

Contact ID

NA

NA

02

SIA

390 ms

1800 Hz

**03

Ademco 4/2 Express

 

 

(Ver. 1.3)

 

 

Upload/Download Rings: Location 29

Location 29 sets the number of rings that the ORBIT-6 will wait before automatically answering an incoming call. If such a call was initiated by the alarm company’s Upload/Download software, a process begins which allows a Remote Programming session to take place.

Location: 29

Number of Rings

Default: 12

Choose a number of rings greater than that which the customer will normally wait to answer

an incoming call enter two digits; (between 00-15 rings)

Number

Note: if an Answering Machine is in use and so programmed

of Rings

(see Location 26 / 2nd Digit), entries made in this location will be ignored

 

 

SYSTEM CONTROLS: LOCATION 30

Location 30 allows you to specify some additional parameters, which determine how the ORBIT-6 will operate. The location contains two digits.

First digit: determine the number (or letter) corresponding to the choices involving Quick Arm / Quick Bypass / UO Extender / Loudspeaker / Bell-Siren

Second digit: determine the number (or letter) corresponding to the use of Silent Panic / Bell Squawk on Arming / 3 Minute Bypass

Comments on System Controls

(Location 30: 1st Digit)

Quick Arm

Quick Bypass

 

UO Extender

Loudspeaker/Bell-Siren

 

 

 

 

 

Quick Arm

Eliminates the

 

select UO Extender

select Loudspeaker if the

eliminates the

need to enter a

 

if the Utility Output

external sounder(s) is NOT

need for entering

User Code when

 

Expansion Module is

equipped with a built-in sound

a User Code when

bypassing a zone.

installed

driver; doing so causes the

arming to the STAY

 

 

 

ORBIT-6 to produce an

or AWAY modes.

 

 

 

oscillating frequency for the

simply pressing

 

 

 

device, select Bell/Siren if the

[STAY] or [ARM] will

 

 

 

external sounder(s) is a bell or

arm the system to

 

 

 

a buzzer or equipped with a

the respective mode

 

 

 

built-in electronic sound driver;.

25

Installer Manual

 

Comments on System Controls

(Location 30: 2nd Digit)

 

 

 

Silent Panic

 

 

Bell Squawk on Arming

3 Minute Bypass Enabled

 

 

 

 

 

 

 

 

 

 

 

 

 

If “NO”, the panic alarm

If selected, Bell Squawk on

If selected, 3-Minute Bypass Enabled

 

 

will be AUDIBLE at the

Arming will produce a brief

bypasses all zones automatically for 3

 

 

External Sounder and

confirmation “chirp” from the

minutes when power is restored to an

 

 

visual on the keypad.

system’s external sounder(s)

“unpowered” system–to prevent

 

 

If “YES”, the panic alarmonce the system is armed

potential false alarms by allowing time

 

 

will be INAUDIBLE at

and the Exit Delay expires

for the stabilization of motion and/or

 

 

the External Sounder

 

 

smoke detectors

 

 

 

and invisable on the

 

 

 

 

 

 

 

keypad.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Location: 30

 

System Controls: (1st Digit):

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1st Digit

Loudspeaker/Bell-Siren

UO Extender

 

Quick Bypass

Quick Arm

 

0

 

 

Bell-Siren

No

 

No

No

 

1

 

 

Bell-Siren

No

 

No

Yes

 

2

 

 

Bell-Siren

No

 

Yes

No

 

3

 

 

Bell-Siren

No

 

Yes

Yes

 

4

 

 

Bell-Siren

Yes

 

No

No

 

5

 

 

Bell-Siren

Yes

 

No

Yes

 

6

 

 

Bell-Siren

Yes

 

Yes

No

 

7

 

 

Bell-Siren

Yes

 

Yes

Yes

 

8

 

 

Loudspeaker

No

 

No

No

 

9

 

 

Loudspeaker

No

 

No

Yes

 

 

(default)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

Loudspeaker

No

 

Yes

No

 

 

B

 

 

Loudspeaker

No

 

Yes

Yes

 

 

C

 

 

Loudspeaker

Yes

 

No

No

 

 

D

 

 

Loudspeaker

Yes

 

No

Yes

 

 

E

 

 

Loudspeaker

Yes

 

Yes

No

 

 

F

 

 

Loudspeaker

Yes

 

Yes

Yes

 

 

 

 

 

 

 

 

 

Location: 30

System Controls: (2nd Digit):

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2nd Digit

 

3 Minute Bypass

CZ Installation

 

Bell Squawk on

Silent Panic

 

 

 

 

 

 

 

 

 

Arm

 

 

0

 

 

Disabled

No

 

No

No

 

1

 

 

Disabled

No

 

No

Yes

 

2

 

 

Disabled

No

 

Yes

No

 

3

 

 

Disabled

No

 

Yes

Yes

 

**4

 

 

Disabled

Yes

 

No

No

 

**5

 

 

Disabled

Yes

 

No

Yes

 

**6

 

 

Disabled

Yes

 

Yes

No

 

**7

 

 

Disabled

Yes

 

Yes

Yes

 

8

 

 

Enabled

No

 

No

No

 

9

 

 

Enabled

No

 

No

Yes

 

 

A

 

 

Enabled

No

 

Yes

No

 

 

B

 

 

Enabled

No

 

Yes

Yes

 

 

(default)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

**C

 

 

Enabled

Yes

 

No

No

 

 

**D

 

 

Enabled

Yes

 

No

Yes

 

 

**E

 

 

Enabled

Yes

 

Yes

No

 

 

**F

 

 

Enabled

Yes

 

Yes

Yes

 

** New in Ver. 1.3

26

Installer Manual

Periodic
Test Time

System Controls:

1ST Digit

System Controls:

2nd Digit

PERIODIC TEST TIME: LOCATION 31

If desired, the ORBIT-6 can send a daily test transmission to the Central Station to verify the operation of the unit’s Digital Communicator.

Location: 31

Periodic Test Time

Default: 0000

Sets a fixed, daily time for sending an ORBIT-6 test transmission to the Central Station. The chosen time is expressed in 24-Hour format (following examples):

8:30 AM=0830 11:15AM=1115 4:30 PM=1630 If desired, disable the test transmission capability by accepting (or entering) the default (0000)

Note: Failure to set the systems’ time clock, will prevent the code from being sent to the Central Station.

COMMUNICATOR REPORTING CODES: LOCATIONS 32 THROUGH 86

To program the codes that will be transmitted by the ORBIT-6 to the Central Station.

To prevent the corresponding event from being reported, use a “double-zero” (00, the default) in the location.

Reporting Codes for Alarm Events:

Location

Description

Digits

Default

Report Code

 

 

 

 

 

32

Zone 1 Alarm Reporting code

2

00

 

33

Zone 2 Alarm Reporting code

2

00

 

34

Zone 3 Alarm Reporting code

2

00

 

35

Zone 4 Alarm Reporting code

2

00

 

36

Zone 5 Alarm Reporting code

2

00

 

37

Zone 6 Alarm Reporting code

2

00

 

38

Zone 7 Alarm Reporting code

2

00

 

39

Zone 8 Alarm Reporting code

2

00

 

40

Keypad Fire Alarms Reporting code

2

00

 

41

Keypad Panic Reporting code

2

00

 

42

Keypad Special Emergency Reporting code

2

00

 

Notes on Alarm Restorals

An ORBIT-6 Restoral Report informs the Central Station that the external sounder’s operation, initially triggered by the respective alarm condition, has either “timed out” or been silenced by the act of system disarming. Be sure to check with Central Station personnel if restorals are permitted and, if so, what codes are required.

Restoral Codes

Location

Description

Digits

Default

Report Code

 

 

 

 

 

43

Zone 1 Restoral Code

2

00

 

44

Zone 2 Restoral Code

2

00

 

45

Zone 3 Restoral Code

2

00

 

46

Zone 4 Restoral Code

2

00

 

47

Zone 5 Restoral Code

2

00

 

48

Zone 6 Restoral Code

2

00

 

49

Zone 7 Restoral Code

2

00

 

50

Zone 8 Restoral Code

2

00

 

51

Keypad Fire Restoral Code

2

00

 

52

Keypad panic Restoral Code

2

00

 

53

Keypad Special Emergency Restoral Code

2

00

 

27

Installer Manual

Other Reporting Codes

Location

Description

 

 

 

Digits

Default

Report Code

 

 

 

 

 

 

 

54

Daily test Report Code sent

everyday at the

time

2

00

 

specified in Location 24

 

 

 

 

 

 

 

 

 

 

 

 

 

55

User 0 arm (the “Master”

Code,

“QuickArm”

OR

2

00

 

“Keyswitch” Arm)

 

 

 

 

 

 

 

 

 

 

 

 

 

56

User 1 arm Reporting code

 

 

 

 

2

00

 

57

User 2 arm Reporting code

 

 

 

 

2

00

 

58

User 3 arm Reporting code

 

 

 

 

2

00

 

59

User 4 arm Reporting code

 

 

 

 

2

00

 

60

User 5 arm Reporting code

 

 

 

 

 

 

 

61

User 6 arm Reporting code

 

 

 

 

 

 

 

62

User 7 arm Reporting code

 

 

 

 

 

 

 

63

User 8 arm Reporting code

 

 

 

 

 

 

 

64

User 9 arm Reporting code

 

 

 

 

 

 

 

65

Forced arm (when the system is

armed with

a

2

00

 

bypassed zone) Reporting code

 

 

 

 

 

 

 

 

 

 

 

66

Stay arm when the system

is armed to the

Stay

2

00

 

(At Home) mode) Reporting code

 

 

 

 

 

 

 

 

 

 

 

67

User 0, disarm Reporting code (key switch disarm)

 

2

00

 

68

User 1 disarm Reporting code

 

 

 

 

2

00

 

69

User 2 disarm Reporting code

 

 

 

 

2

00

 

70

User 3 disarm Reporting code

 

 

 

 

2

00

 

71

User 4 disarm Reporting code

 

 

 

 

2

00

 

72

User 5 disarm Reporting code

 

 

 

 

 

 

 

73

User 6 disarm Reporting code

 

 

 

 

 

 

 

74

User 7 disarm Reporting code

 

 

 

 

 

 

 

75

User 8 disarm Reporting code

 

 

 

 

 

 

 

76

User 9 disarm Reporting code

 

 

 

 

 

 

 

77

Duress Disarm

 

 

 

 

 

 

 

Trouble Reports and Restorals

Location

Description

Digits

Default

Report Code

78

Low Battery Reporting code

2

00

 

79

loss of AC Power (for at least 15 min) Reporting code

2

00

 

80

Fire zone trouble Reporting code

2

00

 

81

Bell Loop Interrupted Reporting Code

2

00

 

82

Low Battery restore Reporting code

2

00

 

83

Loss of AC Power restore Reporting code

2

00

 

84

Fire zone trouble Restore Reporting code

2

00

 

85

Bell Loop Restored Reporting Code

2

00

 

**86

Auto Arm

2

00

 

**New in Version 1.3

28

Installer Manual

ORBIT-6 Installer Programming Worksheet

 

Customer ________________________

 

Address _________________________

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

City ____________ State _____Zip ___

Customer Phone No: (

) ___________________

 

 

 

Date of Installation: ________________

Central Station Account No:___________________

 

 

 

Installer(s): ______________________

Comments:________________________________

 

 

 

Comments: ______________________

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Location

Description

 

 

 

Entry

 

 

Location

Description

 

Entry

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

00

Default Disable

 

 

 

 

 

 

 

 

 

 

 

 

44

 

 

 

 

 

Rst Code Zone 2

 

 

 

 

 

 

 

 

01

MS LOCK

 

 

 

 

 

 

 

 

 

 

 

 

45

 

 

 

 

 

Rst Code Zone 3

 

 

 

 

 

 

 

 

02

Phone No. CS 1

 

See below

 

 

46

 

 

 

 

 

Rst Code Zone 4

 

 

 

 

 

 

 

 

03

Phone No. CS 2

 

See below

 

 

47

 

 

 

 

 

Rst Code Zone 5

 

 

 

 

 

 

 

 

04

UD Call back

 

 

 

See below

 

 

48

 

 

 

 

 

Rst Code Zone 6

 

 

 

 

 

 

 

 

05

CS Account No.

 

 

 

 

 

 

 

 

 

 

49

 

 

 

 

 

Rst Code Zone 7

 

 

 

 

 

 

 

 

06

Access Code

 

 

 

 

 

 

 

 

 

 

 

 

50

 

 

 

 

 

Rst Code Zone 8

 

 

 

 

 

 

 

 

07

Remote ID Code

 

 

 

 

 

 

 

 

 

 

51

 

 

 

 

 

Rst Kpd Fire

 

 

 

 

 

 

 

 

08

Installer Code 1

 

 

 

 

 

 

 

 

 

 

52

 

 

 

 

 

Rst Kpd Panic

 

 

 

 

 

 

 

 

09

Installer Code 2

 

 

 

 

 

 

 

 

 

 

53

 

 

 

 

 

Rst Kpd SP

 

 

 

 

 

 

 

 

10

Master Code

 

 

 

 

 

 

 

 

 

 

 

 

54

 

 

 

 

 

Rpt Code per Test

 

 

 

 

 

 

 

 

11

Exit Delay

 

 

 

 

 

 

 

 

 

 

 

 

55

 

 

 

 

 

User 0 Arm

 

 

 

 

 

 

 

 

12

Entry Delay

 

 

 

 

 

 

 

 

 

 

 

 

56

 

 

 

 

 

User 1 Arm

 

 

 

 

 

 

 

 

13

Bell Cutoff Time

 

 

 

 

 

 

 

 

 

 

57

 

 

 

 

 

User 2 Arm

 

 

 

 

 

 

 

 

14

Zone 1 Settings

 

 

 

 

 

 

 

 

 

 

58

 

 

 

 

 

User 3 Arm

 

 

 

 

 

 

 

 

15

Zone 2 Settings

 

 

 

 

 

 

 

 

 

 

59

 

 

 

 

 

User 4 Arm

 

 

 

 

 

 

 

 

16

Zone 3 Settings

 

 

 

 

 

 

 

 

 

 

60

 

 

 

 

 

User 5 Arm

 

 

 

 

 

 

 

 

17

Zone 4 Settings

 

 

 

 

 

 

 

 

 

 

61

 

 

 

 

 

User 6 Arm

 

 

 

 

 

 

 

 

18

Zone 5 Settings

 

 

 

 

 

 

 

 

 

 

62

 

 

 

 

 

User 7 Arm

 

 

 

 

 

 

 

 

19

Zone 6 Settings

 

 

 

 

 

 

 

 

 

 

63

 

 

 

 

 

User 8 Arm

 

 

 

 

 

 

 

 

20

Zone 7 Settings

 

 

 

 

 

 

 

 

 

 

64

 

 

 

 

 

User 9 Arm

 

 

 

 

 

 

 

 

21

Zone 8 Settings

 

 

 

 

 

 

 

 

 

 

65

 

 

 

 

 

Forced Arm

 

 

 

 

 

 

 

 

22

Utility Output 1

 

 

 

 

 

 

 

 

 

 

 

 

66

 

 

 

 

 

Stay Arm

 

 

 

 

 

 

 

 

23

Utility Output 2

 

 

 

 

 

 

 

 

 

 

 

 

67

 

 

 

 

 

User 0 disarm

 

 

 

 

 

 

 

 

24

Utility Output 3

 

 

 

 

 

 

 

 

 

 

 

 

68

 

 

 

 

 

User 1 disarm

 

 

 

 

 

 

 

 

25

Utility Output 4

 

 

 

 

 

 

 

 

 

 

 

 

69

 

 

 

 

 

User 2 disarm

 

 

 

 

 

 

 

 

26

Dialer Controls

 

 

 

 

 

 

 

 

 

 

 

 

70

 

 

 

 

 

User 3 disarm

 

 

 

 

 

 

 

 

27

CS Protocols 1

 

 

 

 

 

 

 

 

 

 

 

 

71

 

 

 

 

 

User 4 disarm

 

 

 

 

 

 

 

 

28

CS Protocols 2

 

 

 

 

 

 

 

 

 

 

 

 

72

 

 

 

 

 

User 5 disarm

 

 

 

 

 

 

 

 

29

U/D Rings

 

 

 

 

 

 

 

 

 

 

 

 

73

 

 

 

 

 

User 6 disarm

 

 

 

 

 

 

 

 

30

System Controls

 

 

 

 

 

 

 

 

 

 

74

 

 

 

 

 

User 7 disarm

 

 

 

 

 

 

 

 

31

Periodic Time Set

 

 

 

 

 

 

 

 

 

 

75

 

 

 

 

 

User 8 disarm

 

 

 

 

 

 

 

 

32

Zone 1 Alarm

 

 

 

 

 

 

 

 

 

 

 

 

76

 

 

 

 

 

User 9 disarm

 

 

 

 

 

 

 

 

33

Zone 2 Alarm

 

 

 

 

 

 

 

 

 

 

 

 

77

 

 

 

 

 

Duress Disarm

 

 

 

 

 

 

 

 

34

Zone 3 Alarm

 

 

 

 

 

 

 

 

 

 

 

 

78

 

 

 

 

 

Rpt Code Low Bat

 

 

 

 

 

 

 

 

35

Zone 4 Alarm

 

 

 

 

 

 

 

 

 

 

 

 

79

 

 

 

 

 

Rpt Code AC Loss

 

 

 

 

 

 

 

 

36

Zone 5 Alarm

 

 

 

 

 

 

 

 

 

 

 

 

80

 

 

 

 

 

Rpt Code Fire Tbl.

 

 

 

 

 

 

 

 

37

Zone 6 Alarm

 

 

 

 

 

 

 

 

 

 

 

 

81

 

 

 

 

 

Rpt Code Bell Loop

 

 

 

 

 

 

 

 

38

Zone 7 Alarm

 

 

 

 

 

 

 

 

 

 

 

 

82

 

 

 

 

 

Rst Code Low Bat

 

 

 

 

 

 

 

 

39

Zone 8 Alarm

 

 

 

 

 

 

 

 

 

 

 

 

83

 

 

 

 

 

Rst Code AC Loss

 

 

 

 

 

 

 

 

40

Kpd Fire Alarm

 

 

 

 

 

 

 

 

 

 

 

 

84

 

 

 

 

 

Rst Code Fire Tbl.

 

 

 

 

 

 

 

 

41

Kpd Panic Alarm

 

 

 

 

 

 

 

 

 

 

85

 

 

 

 

 

Rst Code Bell Loop

 

 

 

 

 

 

 

 

42

Kpd SP Alarm

 

 

 

 

 

 

 

 

 

 

 

 

**86

 

 

 

Auto Arm

 

 

 

 

 

 

 

 

43

Rst Code Zone 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

**New in Ver. 1.3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Phone 1

 

02

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Phone 2

 

03

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UD Call back

04

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

29

Installer Manual

CONTACT ID & SIA REPORT CODES FOR ORBIT 6

Event Reporting

Contact ID

SIA

 

Zones Alarms/Disarm

Program

Code

Program

 

Code

 

Digit

 

Digit

 

 

Exit/Entry Alarm

01

134

01

 

BA

Exit/Entry Restore

01

134

02

 

BH

Burglary Zone Alarm

03

130

03

 

BA

Burglary Zone Restore

03

130

04

 

BH

24 Hour Zone Alarm

05

133

05

 

BA

24 Hour Zone Restore

05

133

06

 

BH

Tamper Zone Alarm

07

137

07

 

TA

Tamper Zone Restore

07

137

08

 

TR

Smoke Zone Alarm/Restore

09

111

 

 

 

Combustion Zone Alarm/Restore

1A

112

 

 

 

Water Flow Zone Alarm/Restore

11

113

11

 

WA

Heat Zone Alarm

12

114

12

 

KA

Heat Zone Restore

12

114

13

 

KH

Duct Zone Alarm/Restore

14

116

 

 

 

Flame Zone Alarm/Restore

15

117

 

 

 

Panic Zone Alarm

 

 

 

 

 

Restore

 

 

 

 

 

Silent Alarm

16

122

 

 

 

Audible Alarm

17

123

 

 

 

Perimeter Zone Alarm/Restore

18

131

18

 

NL

Interior Zone Alarm/Restore

19

132

 

 

 

Day/Night Zone Alarm/Restore

2A

135

 

 

 

Outdoor Zone Alarm/Restore

21

136

 

 

 

General Alarm/Restore

22

140

 

 

 

Sensor Tamper Alarm/Restore

23

144

 

 

 

24 Hour Non Burg Alarm/Restore

24

150

 

 

 

Gas Detected Alarm

25

151

25

 

GA

Gas Detected Restore

25

151

26

 

GH

Refrigeration Zone Alarm/Restore

27

152

 

 

 

Loss of Heat Alarm/Restore

28

153

 

 

 

Water Leakage Alarm

29

154

29

 

WA

Zones Alarms/Disarm

Program

Code

Program

 

Code

 

Digit

 

Digit

 

 

Water Leakage Restore

29

154

3A

 

WH

Foil Break Alarm/Restore

31

155

 

 

 

Low Battled Gas level Alarm/Restore

32

157

 

 

 

High Temperature Alarm/Restore

33

158

33

 

DA

30

Installer Manual

Event Reporting

Contact ID

SIA

 

Zones Alarms/Disarm

Program

Code

Program

 

Code

 

Digit

 

Digit

 

 

Low Temperature Alarm/Restore

34

159

34

 

DA

Los of Air Flow

35

161

35

 

DB

 

 

 

 

 

 

 

 

 

 

 

 

Special

 

 

 

 

 

Special Emergency Key Alarm

4A

100

4A

 

MA

Special Emergency Key Restore

4A

100

41

 

MH

Fire Zone Alarm

42

110

42

 

FA

Fire Zone Restore

42

110

43

 

FH

Fire Key Alarm

44

115

44

 

FA

Fire Key Restore

44

115

45

 

FH

Panic Key Alarm

46

120

46

 

PA

Panic Key Restore

46

120

47

 

PH

Duress Alarm

48

121

48

 

HA

Duress Restore

48

121

49

 

HH

 

 

 

 

 

 

Troubles

 

 

 

 

 

AC Trouble

5A

301

5A

 

AT

AC Restore

5A

301

51

 

AR

Low Battery Trouble

52

302

52

 

YT

Low Battery Restore

52

302

53

 

YR

Main Bell Trouble

54

321

54

 

YA

Main Bell Restore

54

321

55

 

YH

Fire Trouble

56

373

56

 

FT

Fire Restore

56

373

57

 

FJ

 

 

 

 

 

 

O/C Access

 

 

 

 

 

User Arm

6A

401

6A

 

CL

User Disarm

6A

401

61

 

OP

Quick Arm/Disarm - User 0

62

408

 

 

 

Forced Arm

63

574

63

 

CF

Periodic Test

64

602

64

 

RP

Auto Alarm

65

403

65

 

CA

31

Installer Manual

 

 

ORBIT-6 Wiring Diagram

 

FIGURE 1A

 

 

 

TR1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SIG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J3

 

 

 

 

 

 

 

 

 

 

 

P1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UR1

 

 

 

SET

 

 

 

 

 

 

 

 

 

 

 

DEFAULT

J1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TIP

PHONE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RING

J2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TELEPHONE

 

LINE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TO TELEPHONE

 

AUX

COM CLK

DAT

Z1

C O M

Z2

Z3 COM Z4 Z5

C O M

Z6

AUX

UO

BELL/LS

AC

 

 

 

RED

BLK YEL

GRN

TMP

ECL

+

-

 

 

LINE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-

RECHARGEABLE

 

 

 

 

 

 

TO ZONES CONTACTS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BATTERY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+

TO KEYPAD(S)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16.5 Vac

12V 4ah typical

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12VDC 250 mA

 

 

 

 

 

 

30 VA

 

 

 

 

 

 

 

 

 

 

POWER SUPPLY

 

 

 

 

 

 

 

 

 

 

 

TYPICAL BURGLARY

 

 

 

 

PROGRAMMABLE

 

 

 

 

 

 

BELL

 

 

 

 

 

 

 

 

OPEN COLLECTOR

 

 

 

 

 

 

 

 

 

 

ZONE WIRINGS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MAX 70mA OR

 

 

 

 

 

 

 

 

 

(TWO DETECTIONS FOR EACH ZONE)

 

 

 

 

 

 

 

 

 

OR

12VDC

 

 

 

 

TO UO EXPANDER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LOUD

750 mA MAX

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TYPICAL FIRE

 

 

 

 

 

 

SPEAKER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ZONE WIRINGS

 

 

 

 

 

 

 

 

 

 

 

N/O

 

(4 WIRE SMOKE DETECTIONS )

 

 

 

 

12VDC

 

 

N/C

 

 

 

 

 

 

 

 

 

 

 

SUPERVISING

 

 

CONTACTS

 

CONTACTS

 

 

 

 

 

 

 

 

 

 

RELAY

 

 

Z5

COM

UO

AUX

+IN

 

+OUT

 

 

 

 

-IN

ALARM

+OUT

 

 

 

 

 

CONTACT

END OF LINE RESISTORS 2,2 K 1/4 WATT

32

Installer Manual

 

 

ORBIT-6 Wiring Diagram

 

 

FIGURE 1B

 

 

 

 

TR1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SIG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J3

 

 

 

 

 

 

 

 

 

 

 

 

P1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UR1

 

 

 

SET

 

 

 

 

 

 

 

 

 

 

 

DEFAULT

J1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TIP

PHO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RING

NE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TELEPHONE

LINE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TO TELEPHONE

 

AUX COM CLK

DAT

Z1

C O M Z2

Z3 COM Z4

Z5

C O M

Z6

AUX

UO

BELL/LS

AC

 

 

 

 

 

RED BLK YEL

GRN

TMP

ECL

+

-

 

 

 

 

LINE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-

RECHARGEABLE

 

 

 

 

 

TO ZONES CONTACTS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BATTERY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+

TO KEYPAD(S)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12V 4ah typical

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16.5 Vac

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30 VA

 

 

 

TYPICAL BURGLARY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BELL

 

 

 

ZONE WIRINGS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(TWO DETECTIONS FOR EACH ZONE)

 

 

 

 

 

 

 

 

 

 

 

 

 

OR

12VDC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LOUD

750 mA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MAX

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SPEAKER

 

N/C

N/O

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ONTACTS

CONTACTS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12VDC 250 mA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TYPICAL FIRE

 

POWER SUPPLY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ZONE WIRINGS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(4 WIRE SMOKE DETECTIONS )12VDC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SUPERVISING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RELAY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+IN

+OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-IN

ALARM -OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONTACT

 

 

 

 

 

GND ECL DAT

Uo2

Uo3 Uo4

 

 

 

 

 

 

 

 

 

 

 

 

 

BLK

YEL GRN Uo1

 

 

 

 

 

 

 

 

 

 

 

END OF LINE RESISTORS

2,2 K 1/4 WATT

Installer Manual

33

 

Zone Extension

 

 

Power LED

Z7

COM

Z8

Arm LED

Ready LED

Fire LED

Zone 1

Zone 2

Zone 3

Backlit LEDS

Zone 4

Zone 5

Zone 6/Tmp

Zone 7

Zone 8

AUX GND CLK DAT

WHT RED BLK YEL GRN

(Keypad Buzzer)

 

 

Panic Button

 

Ç

 

 

 

 

To

FIGURE 1C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the

8-ZONE KEYPAD BOARD

 

 

 

 

 

 

 

Control

 

 

 

 

 

 

 

 

 

 

Panel

34

Installer Manual

Notes

Installer Manual

35

 

36

Installer Manual

ROKONET LIMITED WARRANTY

Rokonet Electronics, Ltd. and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and workmanship under normal use for 18 months from the date of production. Because Seller does not install or connect the product and because the product may be used in conjunction with products not manufactured by the Seller, Seller can not guarantee the performance of the security system which uses this product. Sellers obligation and liability under this warranty is expressly limited to repairing and replacing, at Sellers option, within a reasonable time after the date of delivery, any product not meeting the specifications. Seller makes no other warranty, expressed or implied, and makes no warranty of merchantability or of fitness for any particular purpose.

In no case shall seller be liable for any consequential or incidental damages for breach of this or any other warranty, expressed or implied, or upon any other basis of liability whatsoever.

Sellers obligation under this warranty shall not include any transportation charges or costs of installation or any liability for direct, indirect, or consequential damages or delay.

Seller does not represent that its product may not be compromised or circumvented; that the product will prevent any persona; injury or property loss by burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate warning or protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of burglary, robbery or fire without warning, but is not insurance or a guaranty that such will not occur or that there will be no personal injury or property loss as a result.

Consequently seller shall have no liability for any personal injury, property damage or loss based on a claim that the product fails to give warning. However, if seller is held liable, whether directly or indirectly, for any loss or damage arising from under this limited warranty or otherwise, regardless of cause or origin, sellers maximum liability shall not exceed the purchase price of the product, which shall be complete and exclusive remedy against seller. No employee or representative of Seller is authorized to change this warranty in any way or grant any other warranty.

WARNING: This product should be tested at least once a week.

Installer Manual

37