Optex AX-100TFR, AX-100TFRi, AX-200TFR, AX-200TFRi Installation

0 (0)

No.59-1552-0 090128

 

 

 

 

1 INTRODUCTION

INSTALLATION INSTRUCTIONS

 

 

 

 

 

 

1-1

BEFORE YOUR OPERATION

 

 

 

 

 

 

Read this instruction manual carefully prior to installation.

N219

 

 

After reading, store this manual carefully in an easily accessible

 

 

place for reference.

 

 

 

BATTERY OPERATED

 

 

This manual uses the following warning indications for correct use

PHOTOELECTRICIC DETECTOR

 

 

of the product, harm to you or other people and damage to your

 

 

assets, which are described below. Be sure to understand the

AX-100TFR/AX-200 TFR

 

 

description before reading the rest of this manual.

 

 

 

Failure to follow the instructions provided with

FEATURES Warning this indication and improper handling may cause death or serious injury.

•AX-100TFR : Detection range: 30 m (100 ft.)

 

 

Failure to follow the instructions provided with

•AX-200TFR : Detection range: 60 m (200 ft.)

 

 

 

 

Caution this indication and improper handling may cause

Battery-operated detector

 

 

 

 

injury and / or property damage.

Batteries are not included.

 

 

 

 

 

Use four LSH20 (3.6 V, 13 Ah) batteries manufactured by SAFT.

This symbol indicates prohibition. The specific prohibited

Battery life: Approximately five years (AX-100TFR)

action is provided in and/or around the figure.

Approximately three years (AX-200TFR)

 

Back box for wireless transmitters

 

 

This symbol requires an action or gives an instruction.

Back box can conceal two wireless transmitters and batteries.

 

N.C./N.O. selection switch

 

 

 

 

 

Warning

Both N.C. and N.O. input wireless transmitters can be used.

Do not use the product for purposes other than the detection

Battery saving function for wireless transmitter

 

 

 

 

of moving objects such as people and vehicles.

Turning ON the battery saving timer switch reduces the battery

Do not use the product to activate a shutter, etc., which may

consumption of the wireless transmitter.

 

 

 

 

cause an accident.

Intermittent output function

 

 

 

 

Do not touch the unit base or power terminals of the

Turning ON the intermittent output function forces intermittent

product with a wet hand (do not touch when the product

output while the problem status exists.

 

 

 

 

is wet with rain, etc.). It may cause electric shock.

 

 

 

4 channel beam frequency selector

 

 

Never attempt to disassemble or repair the product. It may

Crosstalk is eliminated with 4, channel selectable, beam

cause fire or damage to the devices.

frequencies. Used when stacking beams or for long range

Do not use batteries other than those specified.

applications.

 

 

 

 

Specified batteries:

International protection

 

 

 

 

Four LSH20 batteries manufactured by SAFT

IP55

 

 

 

 

Do not use batteries that have different levels of power

LED indicator for an easy alignment

 

 

 

 

remaining (i.e., new and used batteries).

It flickers on/off to help with easy alignment located on the

Not observing the above may result in an explosion, leakage

receiver.

 

 

 

 

of electrolyte, emission of toxic gases or other outcomes that

 

 

 

D.Q. circuit (environmental disqualification)

 

 

may be harmful to people and property.

The environmental compensation circuit is designed to eliminate

[Handling of Batteries]

false alarms caused by snow, fog, heavy rain, ice and

Fire, explosion and severe burn hazard. Do not recharge,

misalignment.

 

 

 

 

short circuit, crush, disassemble, heat above 100°C (212°F),

 

 

 

Tamper

 

 

incinerate, or expose contents to water.

Form C opens when either cover or back box or chassis is

Do not solder directly to the cell.

removed.

 

 

 

Beam interruption adjustment function

 

 

Caution

This function allows you to select the suitable beam interruption

Do not pour water over the product with a bucket, hose, etc.

time for any environment.

 

 

 

 

The water may enter, which may cause damage to the

 

 

 

CONTENTS

 

 

devices.

 

 

 

1 INTRODUCTION

 

 

Clean and check the product periodically for safe use. If any

 

 

problem is found, do not attempt to use the product as it is

1-1 BEFORE YOUR OPERATION

1

 

 

and have the product repaired by a professional engineer or

1-2 PRECAUTIONS

2

 

electrician.

1-3 PARTS IDENTIFICATION

2

 

 

2 PREPARATIONS

 

 

 

2-1 ORDERING DETECTOR BATTERIES

2

 

 

2-2 CHECKING THE WIRELESS TRANSMITTER SIZE

2

 

 

3 INSTALLATION

 

 

 

3-1 WALL MOUNTING

3

 

 

3-2 POLE MOUNTING

4

 

 

3-3 MOUNTING IN THE BEAM TOWER

5

 

 

3-4 WIRING

7

 

 

4 SETTING

 

 

 

4-1 FUNCTION

8

 

 

4-2 4 CHANNEL BEAM FREQUENCY SELECTOR

8

 

 

4-3 OPTICAL ALIGNMENT

9

 

 

4-4 BEAM INTERRUPTION ADJUSTMENT

9

 

 

4-5 ADJUSTING OUTPUT

10

 

 

5 OPERATION CHECK

 

 

 

5-1 LED INDICATION

11

 

 

5-2 OPERATION CHECK

11

 

 

5-3 TROUBLE SHOOTING

11

 

 

6 SPECIFICATIONS

 

 

 

6-1 SPECIFICATIONS

12

 

 

6-2 DIMENSIONS & OPTION

12

 

 

-1-

Optex AX-100TFR, AX-100TFRi, AX-200TFR, AX-200TFRi Installation

1-2

PRECAUTIONS

Removing the Back Box >>

 

 

 

3 Pull

Install the unit on a stable surface.

Install the pole in a location where sufficient stability can be ensured.

1Loosen the

back box lock screw.

2

Press

Do not install the unit in a location where trees, leaves, or other objects that may swing in the wind may block the beam.

Do not install the receiver in a

Removing the Cover >>

2 Pull

location where it is exposed to

 

 

 

direct sunlight.

 

 

1Loosen the cover lock screw.

Observe the prescribed transmitter-receiver distance (range) and installation height.

AX-100TFR

Detection range: 30 m(100 ft.)

AX-200TFR

Detection range: 60 m(200 ft.)

The pole size should be 4348 mm (1.69"-1.89" ).

2 PREPARATIONS

2-1 ORDERING DETECTOR BATTERIES

Installation Height 0.7 m - 1 m

(2.3 ft. - 3.3 ft.)

Do not allow the infrared beam from a different model to reach the receiver.

Receiver

Transmitter

Transmitter

(different model)

Install the unit more than 1 m (3.3 ft.) away from the wall or fence that are running parallel to the beam.

1 m(3.3 ft.)

The cross () mark indicates prohibition.

1-3 PARTS IDENTIFICATION

Cover

Main unit

Back box

Chassis

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cover lock screw

 

 

 

 

Harness retainer plate

 

 

 

 

 

Back box lock screw

Accessories>>

 

 

 

 

M4×30 screws: 4

 

 

M4×20 screws: 4

M3×8 screws: 6

 

 

 

 

 

 

 

Pole brackets: 6

 

 

Mounting plate

Pole mounting bracket set

 

 

lock screws

U-brackets: 2

Velcro tape: 2 sets

 

 

Specified batteries: Four LSH20 batteries manufactured by SAFT For information about batteries, visit the following website and contact your local SAFT sales representative. http://www.saftbatteries.com/Contacts/tabid/72/FP/9/FROM/PROD UIT/Default.aspx

2-2 CHECKING THE WIRELESS TRANSMITTER SIZE

Use two wireless transmitters for the each of receivers and transmitters. When wireless transmitters with two or more inputs are available, use one wireless transmitter for the each of transmitters and receivers.

The following figure shows the dimensions of the wireless transmitter installation space in the back box. Note that transmitters with dimensions greater than those are not applicable.

42.5(1.67)

42.5(1.67)

78(3.07)

154(6.06)

78(3.07)

154(6.06)

66(2.60)

26.5(1.04)

26.5

(1.04)

Unit: mm(inch)

Note>>

Be sure to monitor the alarm and low battery outputs.

To monitor the tamper output, include a wireless transmitter supporting three or more inputs into the system.

-2-

3 INSTALLATION

3-1 WALL MOUNTING

1 Remove the chassis from the back box.

2 Fix the chassis to the wall.

Wall mounting screws

(M4×20, supplied)

Caution

After mounting the chassis, wiggle the tamper bushing with your thumb and forefinger to ensure the tamper works properly.

3

Connect the cables from the back box to the wireless

 

transmitters.

 

Receiver-Wireless Transmitter Connection

Yellow/Yellow-white cable: For alarm

Green/Green-white cable: For low battery

Black/Black-white cable: For tamper

Transmitter-Wireless Transmitter Connection

Green/Green-white cable: For low battery

Black/Black-white cable: For tamper

Caution

When N.O. wireless transmitters are used, see “Using the N.O. type transmitter” in sec. “3-4” to change the wiring.

Use the specified batteries for the wireless transmitters.

4 Insert the specified batteries into the back box.

Specified batteries SAFT LSH20 3.6V 13Ah

Warning

Do not use batteries other than those specified. Specified batteries:

Four LSH20 batteries manufactured by SAFT

Do not mix batteries that have different levels of power remaining (i.e., new and used batteries). Not observing the above may result in an explosion, leakage of electrolyte, emission of toxic gases or other outcomes that may be harmful to people and property.

Caution

Remove all batteries prior to replacing with new ones. If this is not followed, the low battery indicator LED will not reset and continue to flicker.

5 Fix the wireless transmitters in the back box.

Cut the supplied Velcro tape

to an appropriate length and apply.

6

Run the cables so that they are not pinched between the

 

chassis and back box.

 

7 Install the back box onto the chassis.

Tighten the

back box lock screw.

-3-

3-2 POLE MOUNTING

-Single set

1

Remove the chassis from the back box.

2

Using a screwdriver or similar tool, break the knockout

 

portion as shown.

Knockout two locations pairing in a horizontal line.

3 Install three pole mounting brackets on the chassis.

Install the bracket in the knocked-out locations in step 2 .

M3×8 screw

Pole mounting bracket

(supplied)

(supplied)

4 Fix the chassis on the pole.

U-bracket (supplied)

M4×30 screw (supplied)

Caution

After mounting the chassis, wiggle the tamper bushing with your thumb and forefinger to ensure the tamper works properly.

5

Take steps 3 through 6 refer to sec. “3-1” to install the

 

wireless transmitters and batteries in the back box, and then

install the back box on the chassis.

Tighten the

back box lock screw.

-Two detectors in opposing directions

1

Remove the chassis from the back box.

 

Using a screwdriver or similar tool, break the knockout

2

 

portion as shown.

Detector 1

Detector 2

 

Choose a different

 

pair of knockouts.

3 Install three pole mounting brackets on the chassis.

 

Detector 1

Detector 2

Install the bracket in the knocked-out locations in step 2 .

M3×8 screw

Pole mounting bracket

M3×8 screw

Pole mounting bracket

(supplied)

(supplied)

(supplied)

(supplied)

-4-

Loading...
+ 8 hidden pages