Omega DRN-PS-1000 User Manual

USA	User’sGuide
MADE
IN

®

http://www.omega.com e-mail: [e-mail]

DRN-PS-1000

UNIVERSAL SWITCHING POWER SUPPLY

Compact DIN-Rail 24 Volt

	OMEGAnetSM On-Line Service		Internet e-mail
	http://www.omega.com		[e-mail]
		Servicing North America:
USA:		One Omega Drive, P.O. Box 4047
ISO 9001 Certified		Stamford, CT 06907-0047
		TEL: [phone]	FAX: [phone]
		e-mail: [e-mail]
Canada:		976 Bergar
		Laval (Quebec) H7L 5A1
		TEL: [phone]	FAX: [phone]
		e-mail: [e-mail]

For immediate technical or application assistance:

USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA® Customer Service: 1-800-622-2378 / 1-800-622-BEST® Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN® TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA

Mexico	TEL: (001)800-TC-OMEGASM	FAX: [phone]
	En Español: [phone]-7803	e-mail: [e-mail]
	Servicing Europe:
Benelux:	Postbus 8034, 1180 LA Amstelveen, The Netherlands
	TEL: [phone]	FAX: [phone]
	Toll Free in Benelux: 0800 0993344
	e-mail: [e-mail]
Czech Republic: Rudé armády 1868, 733 01 Karviná 8
	TEL: [phone]	FAX: [phone]
	e-mail: [e-mail]
France:	9, rue Denis Papin, 78190 Trappes
	TEL: [phone]	FAX: [phone]
	Toll Free in France: 0800406342
	e-mail: [e-mail]

Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany

TEL: [phone] FAX: [phone] Toll Free in Germany: 0800 TC-OMEGASM

e-mail: [e-mail]

United Kingdom:	One Omega Drive
ISO 9002 Certified	River Bend Technology Centre
	Northbank, Irlam
	Manchester M44 5EX United Kingdom
	TEL: [phone]	FAX: [phone]
	Toll Free in the UK: 0800 488 488
	e-mail: [e-mail]

It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.

The information contained in this document is believed to be correct but OMEGA Engineering, Inc. accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.

WARNING: These products are not designed for use in, and should not be used for, patient connected applications.

This device is marked with the international caution symbol. It is important to read the Setup Guide before installing or commissioning this device as it contains important information relating to safety and EMC.

CONTENTS

1.	General Information and Features		2
2.	Safety Considerations		3
3.	Installation and Removal		4
	3.1	Installation Clearance	5
	3.2	Mounting on DIN Rail	6
	3.3	Removal of Unit	7
4.	Input and Output Connections		8
	4.1	Block Diagram	8
	4.2	Wiring for 115 Vac - Single Phase	9
	4.3	Wiring for 230 Vac - Two Phase	10
5.	Specifications		11
	Input Power		11
	Output Power		11
	General		12
	Wire Connections		12
6.	Dimensions		13
7.	Temperature Derating Graph		14

1

1GENERAL INFORMATION AND FEATURES

The compact DRN power supplies are designed to supply well-regulated 24 volt DC power to sensors, signal conditioners, data acquisition systems and high level logic equipment.

		Significant DRN features include:
		• Tested isolation, primary to output
	Features
		•	Recessed live parts and connector screws
		• Either 32mm or 35mm DIN rail mounting
		• Wide input voltage tolerances
		• Protective varistor input shunt
		• Input AC spike rejection with LC filters
		• LED power-on lamp
		• Over-temperature protection
		•	Short circuit protection

• Low-ripple, well-regulated design

2

SAFETY CONSIDERATIONS 2

This device is marked with the international Caution symbol. It is important to read this manual before installing or commissioning this device as it contains important information relating to Safety and EMC (Electromagnetic Compatibility).

Unpacking & Inspection

Unpack the instrument and inspect for obvious shipping damage. Do not attempt to operate the unit if damage is found.

This instrument is a DIN rail mount device. Installation of this instrument should be done by Qualified personnel. In order to ensure safe operation, the following instructions should be followed.

This instrument has no power-on switch. An external switch or circuit-breaker shall be included in the building installation as a disconnecting device. It shall be marked to indicate this function, and it shall be in close proximity to the equipment within easy reach of the operator. The switch or circuit-breaker shall not interrupt the Protective Conductor (Earth wire), and it shall meet the relevant requirements of IEC 947–1 and IEC 947-3 (International Electrotechnical Commission). The switch shall not be incorporated in the mains supply cord.

Furthermore, to provide protection against excessive energy being drawn from the mains supply in case of a fault in the equipment, an overcurrent protection device shall be installed.

•The Protective Conductor must be connected for safety reasons. Check that the power cable has the proper Earth wire, and it is properly connected. It is not safe to operate this unit without the Protective Conductor Terminal connected.

•Do not exceed voltage rating on the label located on the top of the instrument

housing.

•Always disconnect power before changing signal and power connections.

•Do not use this instrument on a work bench without its case for safety reasons.

•Do not operate this instrument in flammable or explosive atmospheres.

•Do not expose this instrument to rain or moisture.

•Unit mounting should allow for adequate ventilation to ensure instrument does not exceed operating temperature rating.

•Use electrical wires with adequate size to handle mechanical strain and power requirements. Install without exposing bare wire outside the connector to minimize electrical shock hazards.

EMC Considerations

•Whenever EMC is an issue, always use shielded cables.

•Never run signal and power wires in the same conduit.

•Use signal wire connections with twisted-pair cables.

•Install Ferrite Bead(s) on signal wires close to the instrument if EMC problems persist.

3

3INSTALLATION AND REMOVAL

If a rail assembly is to be transported, then

disconnection, dismounting and separate Warning! packing of the power supply is

recommended.

For units that must be shipped installed on the rail, additional bracing to resist transportation shocks is recommended.

Do not attempt to install or connect to the power supply when the mains are energized.

4