INSTALLATION & OPERATING INSTRUCTIONS READ & SAVE THESE INSTRUCTIONS!
Wireless Chimes
MODELS: LA-228WH or LA-245MR
• For use with the LA-206TWH
Congratulations on your purchase of a NuTone wireless chime. The chime operates by a radio frequency signal transmitted by the pushbutton and received by the chime. The pushbutton/transmitter is mounted at the door. The receiver may be located anywhere in your home within 100 feet (30 meters) of the pushbutton. The pushbutton/transmitter can be programmed to sound one of three chime sounds. This feature allows up to three pushbuttons to generate three different chime sounds.
MOUNTING THE PUSHBUTTON TRANSMITTER
TO OPEN COVER
“PUSH”
FIGURE 1
SCREW HOLE FOR WALL
MOUNTING
SCREW HOLE FOR WALL |
FIGURE 2 |
MOUNTING |
SOUND SELECTION
Refer to Figures 1 and 2.
1.Locate the pushbutton next to or near the door.
Do not mount the pushbutton on a metal surface.
2.Remove the pushbutton cover by inserting the tip of a screwdriver in
the slot at the bottom of the pushbutton and then gently rock the pushbutton cover apart from the pushbutton base.
3.Choose a level place to locate the pushbutton base.
4.Position the pushbutton base,
and mark the mounting surface with a pencil through the two holes in the pushbutton.
5.Drill two 3/16" diameter holes at the previously marked area.
6.Insert the plastic anchors into the 3/16" diameter holes.
7.Place pushbutton over anchors, and fasten with two screws provided. Do not replace cover at this time.
PUSHBUTTON SOUND CODING
Refer to Figure 3.
1.The pushbutton can be coded to sound one of three chime sounds.
2.Select the desired sound as illustrated in Figure 3.
LED
3.Position the plastic jumper straps in the proper location for desired chime sound.
PUSHBUTTON SECURITY CODING
Refer to Figure 3.
It is not necessary to change the security code of the pushbutton unless you experience interference from other wireless devices.
1.To change the security code, remove any combination of the six plastic jumper straps.
2.NOTE: Both the pushbutton and receiver codes must match.
BATTERY INSTALLATION
Refer to Figure 3.
1.Position the A23 12 volt battery as illustrated. Be sure to observe polarity (+/–). For replacement battery, use EverReady® A23BP or Duracell® MN21B (or equivalent).
INSTALLING PUSHBUTTON COVER
Refer to Figure 4.
1.Position the pushbutton cover over the pushbutton base. The red light must be lined up over the hole in the pushbutton cover. Firmly press cover over base.
12V “A23” BATTERY
FIGURE 3
PREPARING THE RECEIVER
REMOVING THE RECEIVER COVER
Refer to Figure 5.
1. Gently push up on the chimes’ cover to disengage the cover from the base and pull cover away from base.
2. Set chime cover aside.
MOUNTING THE
CHIME BASE
Refer to Figure 6.
1. |
Select the desired |
1/8" |
|
|
|
|
|
|
|
|
||||
|
mounting location. This |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
location should be at least |
CHIME |
|
|
|
|
|
|
|
|
|
|
||
|
1 foot away from metal |
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
||||
|
objects and within |
RECEIVER |
|
|
|
|
|
|
|
|
|
|||
|
100 feet (30 meters) of |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
the chime transmitter. |
|
|
|
|
|
|
|
|
|
|
|
KEYHOLE |
|
2. |
Drill one 3/16" hole at the |
|
|
|
|
|
|
|
|
|
|
|
SLOT |
|
|
desired mounting height. |
|
|
|
|
|
|
|
|
|
|
|
|
FIGURE 6 |
|
|
|
|
|
|
|
|
|
|
|
|
|
||
3. |
Insert the plastic anchor |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
into the 3/16" hole. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4.Drive the upper screw into the plastic anchor until the head of the screw extends approximately 1/8" from the mounting surface.
5.Place the keyhole slot in the receiver base over
the screw head. Slide the Receiver down to secure it.
6.Level the chime receiver on the mounting surface.
7.Mark the mounting surface with a pencil at the center of the oval hole in the bottom of the receiver base.
8.Gently remove the chime base from the mounting surface and drill one 3/16" hole at the previously marked area.
9.Insert the plastic anchor into the 3/16" hole and remount the chime receiver.
10.Insert the screw through the chime base into the plastic anchor. Level chime base and tighten screw.
ATTACHING THE RECEIVER COVER
Position chime cover over chime base. Align the mounting tab on cover with slot in top of base.
TROUBLESHOOTING GUIDE
|
PROBLEM |
SOLUTION |
1. |
Chime does not sound. |
Check batteries and polarity. |
|
|
Make sure receiver or pushbutton |
|
|
is not located on metal surface. |
|
|
Check receiver and pushbutton security |
|
|
code. These codes must match. |
|
|
|
2. |
Chime changes tone. |
Check batteries in receiver. |
|
|
|
3. |
Chime looses volume. |
Check batteries in receiver. |
|
|
|
4. |
Chime is activated by another |
Change the security code in the pushbutton |
|
wireless device. |
and receiver. These codes must match. |
|
|
|
5. |
When pushbutton is pressed, the |
Check the sound code jumpers |
|
incorrect chime sound is heard. |
in the pushbutton. |
|
|
|
RECEIVER SECURITY CODING
Refer to Figure 7. |
|
Changing the |
|
Security code is not |
|
|
|
necessary unless |
|
you have changed |
|
the security code in |
|
the pushbutton. |
|
Both the |
|
pushbutton and |
|
receiver codes |
POWER |
must match. |
|
1. Remove the |
SWITCH |
same jumpers |
|
in the receiver |
|
as in the |
3 – “D” SIZE |
pushbutton. |
BATTERIES |
|
FIGURE 7 |
INSTALLING
BATTERIES IN RECEIVER
Refer to Figure 7.
Refer to Figure 7 for placement and polarity of batteries. The NuTone wireless chime requires three “D” size alkaline batteries.
ADJUSTING THE RECEIVER VOLUME
Refer to Figure 7.
1.Slide power switch to the ON position.
2.Press pushbutton. The red light will light.
3.Adjust volume control to desired sound level. To increase volume, turn the control clockwise.
Product specifications subject to change without notice.
4820 Red Bank Road, Cincinnati, Ohio 45227 Printed in China, Rev. 9/06, Part No. 85719