2800 Southcross Drive West,
PO Box 1219
Burnsville, MN 55337, USA
ELECTRIC HOIST
Item# 14226 Item# 14230 Item# 142260 Item# 142262
Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
PRODUCT SPECIFICATIONS
Model |
HGS220/440LB |
HGS550/1100LB |
HGS750/1500LB |
HGS1000/2000LB |
||||||||
|
Standard |
|
With pulley |
Standard |
|
With pulley |
Standard |
|
With pulley |
Standard |
|
With pulley |
|
version |
|
Hook |
version |
|
Hook |
version |
|
Hook |
version |
|
Hook |
|
|
|
|
|
|
|
|
|
|
|
|
|
Load capacity |
220lb |
|
440lb |
550lb |
|
1100lb |
750lb |
|
1500lb |
1000lb |
|
2000lb |
Lifting height |
36ft |
|
18ft |
36ft |
|
18ft |
36ft |
|
18ft |
36ft |
|
18ft |
Lifting speed |
33ft/min |
|
16.5ft/min |
33ft/min |
|
16.5ft/min |
33ft/min |
|
16.5ft/min |
33ft/min |
|
16.5ft/min |
Cable length |
|
39ft |
|
39ft |
|
39ft |
|
39ft |
||||
Cable diameter |
1 / 8 |
anti-twist |
5/ 32 |
anti-twist |
5/ 32 |
anti-twist |
7/ 32 |
anti-twist |
||||
Resister cable |
≥1540lb |
≥2200lb |
≥3000lb |
≥4000lb |
||||||||
Duty circle |
S3 20%-10min |
S3 20%-10min |
S3 20%-10min |
S3 20%-10min |
||||||||
Voltage |
110V/60Hz |
110V/60Hz |
110V/60Hz |
110V/60Hz |
||||||||
Motor performance |
3 /4 HP |
1-3 / 4 HP |
|
2 HP |
2-1/ 4 HP |
SAVE THIS MANUAL
You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep this manual and invoice in a safe and dry place for future reference.
GENERAL SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in
Electric shock, fire, and/or serious injury.
SAVE THESE INSTRUCTIONS
WORK AREA
1.Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
2.Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
3.Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed.
PAGE 2
ELECTRICAL SAFETY
4.Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.
5.Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire
grounded power cord and grounded power supply system.
6.Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded.
7.Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
8.Do not abuse the Power Cord. Never use the Power Cord to carry the tools or pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp edges, or moving parts. Replace damaged Power Cords immediately.
Damaged Power Cords increase the risk of electric shock.
9.When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. These extension cords are rated for outdoor use, and reduce the risk of electric shock.
PERSONAL SAFETY
10.Stay alert. Watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
11.Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
PAGE 3
12.Avoid accidental starting. Be sure the Power Switch is off before plugging in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents.
13.Remove adjusting keys or wrenches before turning the power tool on. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury.
14.Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the power tool in unexpected situations.
15.Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.
PERSONAL SAFETY
16.Do not force the tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.
17.Do not use the power tool if the Power Switch does not turn it on or off.
Any tool that cannot be controlled with the Power Switch is dangerous and must be replaced.
18.Disconnect the Power Cord Plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally.
19.Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.
20.Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired.
21.Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.
PAGE 4