Nortel Networks T7316E User Manual

0 (0)
Nortel Networks T7316E User Manual

Return

 

A

 

Cord connections

 

 

 

to Menu

 

 

B

1

 

 

 

 

 

 

 

 

J

J

 

T7316E Telephone User Card

 

C

 

 

 

 

 

H

 

 

 

 

 

 

 

 

D

 

I

 

 

 

 

 

 

 

 

 

E

K

K

Slide feature card plate down.

 

 

 

 

 

 

 

 

 

 

 

 

2

Desk mount option

 

 

F

L

 

Route line cord through the stand.

 

 

 

 

 

 

 

G

 

 

Headset option

 

 

 

 

 

Connect cord to

 

 

 

 

 

headset.

1-800-4 NORTEL

www.nortelnetworks.com

M

 

© 2003 Nortel Networks

 

P0603479 02

N

Printed in Canada

Your T7316E telephone

ATelephone light

Flashes for incoming calls.

Lights up when Message Waiting Indication (MWI) is supported by system software. Contact your system administrator for more information.

BAdjustable tilt display

Shows the time and date, call and feature information.

CDisplay buttons

The label for display buttons appear in capital letters on the bottom of the display. Display buttons change with each feature you use.

 

Contrast level 2

 

 

Feature message

 

 

 

 

 

DOWN UP OK

 

Display button label

 

 

 

 

 

 

 

Display button

D®Release button

Ends an active call or feature.

EDial pad

FVolume control

Adjusts the handset, handsfree, headset and ringer volume.

More on your T7316E telephone

G Audio cluster buttons

©Mute button

Turns the microphone off or on when you are on a call.

Handsfree button

For more information on using the handsfree feature, refer to the “Handsfree calls” section in this card.

¬Headset button

Turns the headset mode on.

HFeature button

Starts or ends a feature.

IHold button

Places calls on hold.

JMemory buttons

KMemory and line buttons

LIndicators

Appear next to active line and memory buttons.

MNumber card

Write your extension number on this card.

NFeature card plate

Storage compartment for your feature card.

Connect cord to handset.

3

Connect line cord to wall jack.

Wall mount without a telephone stand

1

Press here to remove the stand.

Connect cords to the telephone, refer to “Cord connections” illustrations.

2

Connect line cord to wall jack.

Place the telephone onto the wall mount plate and slide it down.

Wall mount with a telephone stand

1

Press here to remove the stand.

key hole slots

Use the key hole slots on the stand to mark the location for the screws. Tighten screws for a secure fit.

2

Mount the stand as shown.

Connect cords to the telephone, refer to “Cord connections” illustrations.

3

Mount the telephone onto the screws and slide it down.

Connect line cord to wall jack.

Telephone setup

Display contrast level

Adjust the contrast of your display.

1.Press ≤•‡.

2.Press UP or DOWN to view the levels.

3.Press OK to select a level.

Language choice

≤•fi‚⁄

Select Primary Language for the telephone display.

≤•fi‚¤

Select Alternate Language for the telephone display.

≤•fi‚‹

Select Alternate Language 2 for the telephone display.

≤•fi‚›

Select Alternate Language 3 for the telephone display.

Ring type

Select a different ring for your telephone.

1.Press ≤•fl.

2.Press ⁄, ¤, ‹, ›or NEXT to hear the different ring types.

3.Press OK to store the ring type.

Loading...
+ 1 hidden pages