New Holland
Pull-Type Forage Harvester Specifications
790 |
FP230 |
FP240 |
|
|
|
MODEL |
|
|
790 |
FP230 |
FP240 |
Weight (single axle), lbs. (kg) |
3104 (1411) |
4500 (2040) |
4700 (2130) |
||
Length, ft. in. (m) |
|
16’ 1-1⁄4” (4.98) |
................................................................ |
21’ 6” (6.5) ................................................................ |
|
Height with standard spout, ft. in. (m) |
10’ 6” (3.2) |
..................................................................... |
11’ 2”..................................................................... |
||
Width, ft. in. (m) |
|
9’ 6” (2.79) ................................................................ |
|
10’ 8” (3.3) ................................................................ |
|
Number/type of knives.......................................................................................................... |
...................................................................................... |
12 single - edge hardened alloy |
|||
Cutterhead, type/speed ............................................................................ |
................................... .............................................................................................. |
Cylinder, 850 rpm |
|
||
Cutterhead, diameter, in. (mm) |
19-5⁄16 (490.5) ................................................................. |
|
21 (533.4)................................................................. |
||
Throat opening, in. (mm) |
19 x 4-5⁄8 (482 x 117) |
22 x 6 - 5⁄8 (558.8 x 167.7) |
24-3⁄8 x 6-5⁄8 (619.76 x 167.6) |
||
Shearbar .............................................................................................. |
|
Quick adjust, reversible, hard-faced on vertical and horizontal surfaces ...................................................... |
|||
Length of cut, in. (mm)* |
1⁄8 to 1-1⁄2 (3.2 to 38.1) .................................................... |
3⁄16 to 7⁄16* (4.8 to 11.1) .................................................... |
|||
Blower speed |
|
1000 or 750 rpm .................................................................. |
|
1000 rpm.................................................................. |
|
Recommended max. tractor hp |
150 PTO hp |
225 PTO hp |
300 hp |
||
Minimum power required |
75 PTO hp |
150 PTO hp |
180 PTO hp |
||
Knife sharpener |
|
2” manual, built-in ........................................................... |
|
3” manual, built-in........................................................... |
|
Recutter screens (non processor units) |
5 sizes available ............................................................. |
|
6 sizes available............................................................. |
||
Vertical wheel adjustment, in. (mm) |
4-1⁄2 (114) .................................................................... |
|
6 (152).................................................................... |
||
Tire sizes, single axle |
11Lx14 6PR standard |
31x13.5 - 158PR standard |
14Lx16.1 8PR standard |
||
|
|
|
31x13.5-156PR optional |
14Lx16.1 8PR optional |
|
Tire sizes, tandem axle |
N/A |
11Lx15 - 156PR |
11Lx15-15 6PR |
||
*Longer lengths of cut can be obtained by removing knives—up to 1-5⁄16” length of cut with only four knives.
Optional CropPro™ Crop Processor |
Not available |
................................................................... |
Optional................................................................... |
Construction |
— ............................................... |
Hardened ductile iron, steel shaft............................................... |
|
Weight, lbs. (kg) |
— |
490 (218) |
520 (231) |
Roll width, in. (mm) |
— |
24 - 1/2 (622.3) |
26-7⁄8 (682.6) |
Roll diameter, in. (mm) |
— ................................................................. |
|
7-7⁄8 (200)................................................................. |
Roll gap, in. (mm) |
— ...................................................... |
|
3⁄16 to 5⁄8 (4.8 to 15.9) ...................................................... |
Roll speed |
— ............................................................ |
|
2650 rpm upper ............................................................ |
|
............................................................. |
|
2250 rpm lower............................................................. |
Page 1of 2
Loading...