Power LED
Ethernet LED
Powerline LED
Security button
|
Factory Reset button |
|
|
Item |
Description |
Power |
• Solid green. The electrical power is on. |
LED |
• Solid amber. The adapter is in power saving mode. |
|
Power saving mode is disabled by default. |
|
• Blinking green. The adapter is in the process of |
|
setting up security. |
|
• Off. There is no electrical power. |
|
|
Ethernet |
• Solid. The adapter is connected through the |
LED |
Ethernet port to a powered-on Ethernet device. |
|
• Off. There is no Ethernet connection. |
|
|
Item |
Description |
|
|
|
Powerline |
• Solid. The adapter is connected to a Powerline |
|||
LED |
network. |
|
|
|
|
• Off. The adapter has not found any other |
|||
|
compatible Powerline devices using the same |
|||
|
encryption key. |
|
|
|
|
|
|||
|
The Pick A Plug feature lets you pick the electrical |
|||
|
outlet with the fastest link rate, indicated by the color of |
|||
|
the LED. |
|
|
|
|
|
|
|
|
|
Green: Link |
|
Amber: Link rate > |
Red: Link |
|
rate > 80 Mbps |
|
50 and < 80 Mbps |
rate < 50 |
|
(Fast) |
|
(Medium) |
Mbps (Slow) |
|
|
|
|
|
Factory |
Press the Reset button for 1 second, then release it to |
|||
Reset |
return the Powerline adapter to its factory default |
|||
|
settings. |
|
|
|
|
|
|||
Security |
After you plug in your new adapter, press the Security |
|||
Button |
button for 2 seconds, then press the Security button |
|||
|
on one of the other adapters in your existing network |
|||
|
for 2 seconds. Both buttons must be pressed within 2 |
|||
|
minutes. |
|
|
|
|
To enable power saving mode, press and hold the |
|||
|
Security button for 10 seconds or more, then release |
|||
|
it. Pressing the Security button again powers the |
|||
|
adapter back on. |
|
|
|
|
|
|
|
|
WARNING: Do not press the Security button on the Powerline adapter until installation is complete and the adapters are communicating with each other (indicated by the blinking Powerline LED). Pressing this button too soon can temporarily disable Powerline communication. If this should occur, use the Factory Reset button to return the Powerline adapter to its factory default settings.
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com.
You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website.
For product updates and web support, visit
http://support.netgear.com.
NETGEAR recommends that you use only the official NETGEAR support resources.
You can get the user manual online at http://downloadcenter.netgear.com or through a link in the product’s user interface.
For the current EU Declaration of Conformity, visit http://support.netgear.com/app/answers/detail/a_id/11621/.
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134 USA
March 2013
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/ or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. © NETGEAR, Inc. All rights reserved.
For indoor use only. Valid for sale in all EU member states, EFTA states, and Switzerland.
Installation Guide
Powerline AV 200 Mini Set XAVB1301
Powerline
AV 200 Mini
Adapters
Ethernet
cables