Size:
2.73 Mb
Download

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Configuring a WNDAP350 as a Point-to-PointBridge

To configure a point-to-pointbridge as shown inFigure 4-8:

1.Under the Configuration tab, selectWireless Bridge. Then, selectBridging. The Bridging screen displays (seeFigure 4-6).

2.Configure the WNDAP350 (AP1) on LAN Segment 1 in Point-to-PointBridge mode.

AP1

AP2

AP in

AP in

Point-to-Point

Point-to-Point

Bridge Mode

Bridge Mode

 

Router

Hub or Switch

 

LAN

LAN

Segment 2

Segment 1

 

Figure 4-8Wirelesspoint-to-pointbridge setup

 

3.Configure the WNDAP350 (AP2) on LAN Segment 2 in Point-to-PointBridge mode.

AP1 must have AP2’s MAC address in its Remote MAC Address field and AP2 must have AP1’s MAC address in its Remote MAC Address field.

4.Configure and verify the following parameters for both access points:

Verify that the LAN network configuration of the WNDAP350 wirelss access points both are configured to operate in the same LAN network address range as the LAN devices

Both use the same ESSID, Channel, authentication mode, if any, and security settings if security is in use.

5.Verify connectivity across the LAN 1 and LAN 2.

A computer on either LAN segment should be able to connect to the Internet or share files and printers of any other PCs or servers connected to LAN Segment 1 or LAN Segment 2.

6.Click Apply to save your settings.

Advanced Configuration

4-13

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Configuring a Point-to-Multi-PointWireless Bridge

To configure a point-to-multi-pointwireless bridge as shown inFigure 4-9:

1.Under the Configuration tab, selectWireless Bridge. Then, selectBridging. The Bridging screen displays.

AP1

 

AP3

AP in

 

AP in

Point-to-Point

 

Point-to-Point

Bridge Mode

 

Bridge Mode

 

AP2

 

 

 

Hub or Switch

Router

 

 

 

'Master' AP in

 

 

Point-to-Multi-Point

 

192.168.0.1

Bridge Mode

LAN

 

 

LAN

Hub or Switch

Segment 3

Segment 1

 

 

LAN

Segment 2

Figure 4-9Wirelesspoint-to-multipointbridge setup

2.Configure the Operating Mode of the WNDAP350 wirelss access points.

WNDAP350 (AP1) on LAN Segment 1 in Point-to-PointBridge mode with the Remote MAC Address of AP2.

Because it is in the central location, configure WNDAP350 (AP2) on LAN Segment 2 in Point-to-Multi-PointBridge mode. The MAC addresses of the adjacent APs are required in AP2.

Configure the WNDAP350 (AP3) on LAN 3 in Point-to-PointBridge mode with the Remote MAC Address of AP2.

3.Verify the following parameters for all access points:

Verify that the LAN network configuration the WNDAP350 wirelss access points are configured to operate in the same LAN network address range as the LAN devices

Only one access point is configured in Point-to-Multi-PointBridge mode, and all the others are inPoint-to-PointBridge mode.

All access points must be on the same LAN. That is, all the APs LAN IP address must be in the same network.

4-14

Advanced Configuration

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

If using DHCP, all WNDAP350 wirelss access points should be set to “Obtain an IP address automatically (DHCP Client)” in the IP Address Source portion of the Basic IP Settings menu.

All WNDAP350 wirelss access points use the same SSID, Channel, authentication mode, if any, and encryption in use.

All Point-to-PointAccess Points must have the AP2 MAC address in its Remote AP MAC address field.

4.Verify connectivity across the LANs.

A computer on any LAN segment should be able to connect to the Internet or share files and printers with any other PCs or servers connected to any of the three LAN segments.

Wireless stations will be able to connect to the WNDAP350 wirelss access points in the illustration above. If you require wireless stations to access any LAN segment, you can add additional WNDAP350 wirelss access points configured in Wireless Access Point mode to any LAN segment.

5.Click Apply to save your settings.

Note: You can extend thismulti-pointbridging by adding additional WNDAP350s configured inPoint-to-Pointmode for each additional LAN segment. Furthermore, you can extend the range of the wireless network with NETGEAR wireless antenna accessories.

Advanced Configuration

4-15

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

4-16

Advanced Configuration

v1.1, November 2009

Chapter 5

Troubleshooting and Debugging

This chapter provides information about troubleshooting your ProSafe Dual Band Wireless-NAccess Point WNDAP350. After each problem description, instructions are given to help you diagnose and solve the problem. For the common problems listed, go to the section indicated.

Is the WNDAP350 on?

Go to “Installing the WNDAP350 wirelss access point” on page 2-4

Have I connected the wireless access point correctly?

Go to “Installing the WNDAP350 wirelss access point” on page 2-4.

• I cannot remember the wireless access point’s configuration password. Go to “Changing the Administrator Password” on page 3-10.

Note: Forup-to-dateWNDAP350 installation details and troubleshooting guidance visithttp://kbserver.netgear.com/products/WG302.asp.

If you have trouble setting up your WNDAP350, check the tips below.

No lights are lit on the wireless access point.

It takes a few seconds for the power indicator to light up. Wait a minute and check the power light status on the access point.

If the access point has no power.

Make sure the power cord is connected to the access point.

Make sure the power adapter is connected to a functioning power outlet. If it is in a power strip, make sure the power strip is turned on. If it is plugged directly into the wall, verify that it is not a switched outlet.

Make sure you are using the correct NETGEAR power adapter supplied with your access point.

5-1

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

The Wireless LAN activity light does not light up.

The access point antennas are not working.

If the Wireless LAN activity light stays off, disconnect the adapter from its power source and then plug it in again.

Make sure the antennas are tightly connected to the WNDAP350.

Contact NETGEAR technical support if the Wireless LAN activity light remains off.

The LAN light is not lit.

There is a hardware connection problem.Check these items:

Make sure the cable connectors are securely plugged in at the access point and the network device (hub, switch, or router). A switch, hub, or router must be installed between the access point and the Ethernet LAN or broadband modem.

LAN light does not light up if it is a 10 Mbps link. In such cases, the Lan activity light will still blink if there is activity.

Make sure the connected device is turned on.

Be sure the correct cable is used. Use a standard Category 5 Ethernet patch cable. If the network device has Auto Uplink™ (MDI/MDIX) ports, you can use either a crossover cable or a normal patch cable.

I cannot access the Internet or the LAN with a wireless capable computer.

There is a configuration problem. Check these items:

You may not have restarted the computer with the wireless adapter to have TCP/IP changes take effect. Restart the computer.

The computer with the wireless adapter may not have the correct TCP/IP settings to communicate with the network. Restart the computer and check that TCP/IP is set up properly for that network. The usual setting for Windows the Network Properties is set to “Obtain an IP address automatically.”

5-2

Troubleshooting and Debugging

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

The access point’s default values may not work with your network. Check the access point default configuration against the configuration of other devices in your network.

I cannot connect to the WNDAP350 to configure it.

Check these items:

The WNDAP350 is properly installed, LAN connections are OK, and it is powered on. Check that the LAN port LED is green to verify that the Ethernet connection is OK.

The default configuration of the WNDAP350 is for a static IP address of 192.168.0.237 and a Mask of 255.255.255.0 with DHCP disabled. Make sure your network configuration settings are correct.

If you are using the NetBIOS name of the WNDAP350 to connect, ensure that your computer and the WNDAP350 are on the same network segment or that there is a WINS server on your network.

If your computer is set to “Obtain an IP Address automatically” (DHCP client), restart it.

If your computer uses a Fixed (Static) IP address, ensure that it is using an IP Address in the range of the WNDAP350. The WNDAP350 default IP Address is 192.168.0.237 and the default Subnet Mask is 255.255.255.0. If you are not sure about these settings, follow the instructions for “Installing the WNDAP350 wirelss access point” on page 2-4.

When I enter a URL or IP address I get a timeout error.

A number of things could be causing this. Try the following troubleshooting steps.

Check whether other PCs work. If they do, ensure that your PCs TCP/IP settings are correct. If using a Fixed (Static) IP Address, check the Subnet Mask, Default Gateway, DNS, and IP Addresses.

If the PCs are configured correctly, but still not working, ensure that the WNDAP350 is connected and turned on. Connect to it and check its settings. If you cannot connect to it, check the LAN and power connections.

If the WNDAP350 is configured correctly, check your Internet connection (DSL/Cable modem etc.) to make sure that it is working correctly.

Try again.

Troubleshooting and Debugging

5-3

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Using the Reset Button to Restore Factory Default Settings

The Reset button (see “Rear Panel” on page 1-8)has two functions:

Reboot. When pressed and released quickly, the WNDAP350 will reboot (restart).

Reset to Factory Defaults. This button can also be used to clear ALL data and restore ALL settings to the factory default values.

To clear all data and restore the factory default values:

1.Power off the WNDAP350 and power it back on.

2.Use something with a small point, such as a pen, to press the Reset button in and hold it in for at least 5 seconds.

3.Release the Reset button.

The factory default configuration has now been restored, and the WNDAP350 is ready for use.

5-4

Troubleshooting and Debugging

v1.1, November 2009

Appendix A

Default Settings and Technical Specifications

This appendix provides the factory default settings and technical specifications for the ProSafe Dual Band Wireless-NAccess Point WNDAP350.

Factory Default Settings

You can use the reset button located on the front of your device to reset all settings to their factory defaults. This is called a hard reset.

To perform a hard reset, push and hold the reset button for approximately 5 seconds (until the TEST LED blinks rapidly). Your device will return to the factory configuration settings shown in Table A-1 below.

Pressing the reset button for a shorter period of time will simply cause your device to reboot.

Table A-1.Access Point Default Configuration Settings

Feature

Description

 

 

 

AP Login

 

 

 

 

 

User Login URL

192.168.0.237

 

 

 

 

User Name (case sensitive)

admin

 

 

 

 

Login Password (case sensitive)

password

 

 

 

Ethernet Connection

 

 

 

 

 

Static IP Address

192.168.0.210

 

 

 

 

Ethernet MAC Address

See bottom label.

 

 

 

 

Port Speed

10/100/1000

 

 

 

Local Network (LAN)

 

 

 

 

 

Lan IP

192.168.1.1

 

 

 

 

Subnet Mask

255.255.255.0

 

 

 

 

Gateway Address

0.0.0.0

 

 

 

 

DHCP Server

Disabled

 

 

 

Default Settings and Technical Specifications

A-1

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Table A-1.Access Point Default Configuration Settings

Feature

Description

 

 

 

 

DHCP Client

Disabled

 

 

 

 

Time Zone

USA-Pacific

 

 

 

 

Time Zone Adjusted for Daylight Saving

Disabled

 

Time

 

 

SNMP

Enabled, but Trap forwarding disabled

 

 

 

 

Spanning Tree Protocol

Disabled

 

 

 

 

Secure Telnet

Enabled

 

 

 

Wireless

 

 

 

 

 

Operating Mode

Access Point

 

Access Point Name

netgearxxxxxx where xxxxxx are the last 6 digits of the

 

 

wireless access point MAC address.

 

Wireless Communication

Enabled

 

 

 

 

11a/na Wireless Network Name (SSID)

NETGEAR_11a

 

 

 

 

11 b/bg/ng Wireless Network Name

NETGEAR_11g

 

(SSID)

 

 

Broadcast Network Name SSID

Enabled

 

 

 

 

Security

Disabled

 

 

 

 

Transmission Speed

Besta

 

Country/Region

Varies by region

 

 

 

 

80211.a Radio Frequency Channel

Auto

 

 

 

 

80211.g Radio Frequency Channel

Auto

 

 

 

 

Output Power

Full

 

Wireless Card Access List

All wireless stations allowed

 

WMM Support

Enabled

a. Maximum Wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate.

A-2

Default Settings and Technical Specifications

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Technical Specifications

Table A-2.WNDAP350 Technical Specifications

Parameter

ProSafe Dual Band Wireless-NAccess Point WNDAP350

 

 

802.11a Data Rates

6, 9, 12, 18, 24, 36, 48, 54, and 108 Mbps (Auto-ratecapable)

 

 

802.11na Data Rates

Data Rates for Channel Width=20MHz and Guard Interval=short (400ms): Best,

 

7.2 Mbps, 14.4 Mbps, 21.7 Mbps, 28.9 Mbps, 43.3 Mbps, 57.8 Mbps, 65 Mbps,

 

72.2 Mbps, 14.44 Mbps, 28.88 Mbps, 43.33 Mbps, 57.77 Mbps, 86.66 Mbps,

 

115.56 Mbps, 130 Mbps, 144.44 Mbps

 

 

 

Data Rates for Channel Width=20MHz and Guard Interval=long (800ms): Best,

 

6.5 Mbps, 13 Mbps, 19.5 Mbps, 26 Mbps, 39 Mbps, 52 Mbps, 58.5 Mbps, 65

 

Mbps, 13 Mbps, 26 Mbps, 39 Mbps, 52 Mbps, 78 Mbps, 104 Mbps, 117 Mbps,

 

130 Mbps

 

 

 

Data Rates for Channel Width=40MHz and Guard Interval=short: Best, 15 Mbps,

 

30 Mbps, 45 Mbps, 60 Mbps, 90 Mbps, 120 Mbps, 135 Mbps, 150 Mbps, 30

 

Mbps, 60 Mbps, 90 Mbps, 120 Mbps, 180 Mbps, 240 Mbps, 270 Mbps, 300

 

Mbps

 

 

 

Data Rates for Channel Width=40MHz and Guard Interval=long: Best, 13.5

 

Mbps, 27 Mbps, 40.5 Mbps, 54 Mbps, 81 Mbps, 121.5 Mbps, 135 Mbps, 27

 

Mbps, 54 Mbps, 81 Mbps, 162 Mbps, 216 Mbps, 243 Mbps, 270 Mbps

 

 

802.11a/na

 

Operating Frequencies

 

FCC operating

5150MHz ~ 5250MHz

Frequencies

5725MHz ~ 5825MHz

CE(EU) operating

5150MHz ~ 5250MHz

frequencies

5250MHz ~ 5350Mz

 

5470MHz ~ 5725MHz

 

 

802.11a/na Encryption

64-bits,128and152-bitsWEP, AES, TKIP data encryption

 

 

802.11g Data Rates

1, 2, 5.5, 11, 12, 18, 24, 36, 38, 54, & 108 Mbps (Auto-ratecapable)

 

 

Default Settings and Technical Specifications

A-3

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

Table A-2.WNDAP350 Technical Specifications

Parameter

ProSafe Dual Band Wireless-NAccess Point WNDAP350

 

 

802.11ng Data Rates

Data Rates for Channel Width=20MHz and Guard Interval=short (400ms): Best,

 

7.2 Mbps, 14.4 Mbps, 21.7 Mbps, 28.9 Mbps, 43.3 Mbps, 57.8 Mbps, 65 Mbps,

 

72.2 Mbps, 14.44 Mbps, 28.88 Mbps, 43.33 Mbps, 57.77 Mbps, 86.66 Mbps,

 

115.56 Mbps, 130 Mbps, 144.44 Mbps

 

 

 

Data Rates for Channel Width=20MHz and Guard Interval=long (800ms): Best,

 

6.5 Mbps, 13 Mbps, 19.5 Mbps, 26 Mbps, 39 Mbps, 52 Mbps, 58.5 Mbps, 65

 

Mbps, 13 Mbps, 26 Mbps, 39 Mbps, 52 Mbps, 78 Mbps, 104 Mbps, 117 Mbps,

 

130 Mbps

 

 

 

 

Data Rates for Channel Width=40MHz and Guard Interval=short: Best, 15 Mbps,

 

30 Mbps, 45 Mbps, 60 Mbps, 90 Mbps, 120 Mbps, 135 Mbps, 150 Mbps, 30

 

Mbps, 60 Mbps, 90 Mbps, 120 Mbps, 180 Mbps, 240 Mbps, 270 Mbps, 300

 

Mbps

 

 

 

 

Data Rates for Channel Width=40MHz and Guard Interval=long: Best, 13.5

 

Mbps, 27 Mbps, 40.5 Mbps, 54 Mbps, 81 Mbps, 121.5 Mbps, 135 Mbps, 27

 

Mbps, 54 Mbps, 81 Mbps, 162 Mbps, 216 Mbps, 243 Mbps, 270 Mbps

 

 

 

802.11b/bg/ng

2.412 ~ 2.462 GHz (US)

2.457 ~ 2.462 GHz (Spain)

Operating Frequencies

2.412 ~ 2.484 GHz (Japan)

2.457 ~ 2.472 GHz (France)

 

2.412 ~ 2.472 GHz (Europe ETSI)

 

 

 

802.11 b/bg/ng

64-bits,128and152-bitsWEP, AES, TKIP data encryption

Encryption

 

 

 

 

Network Management

Web-basedconfiguration and status monitoring

 

 

Maximum Clients

Limited by the amount of wireless network traffic generated by each node;

 

maximum 64 supported.

 

 

 

Status LEDs

Power/Ethernet LAN/Wireless LAN/Test

 

 

 

Power Adapter

12V DC, 1.5 A

 

 

 

Electromagnetic

FCC Part 15 Class B and Class E, CE, and C-TICK

Compliance

 

 

 

 

 

Environmental

Operating temperature: 0 to 50° C

 

Specifications

Operating humidity: 5-95%,non-condensing

 

 

 

A-4

Default Settings and Technical Specifications

v1.1, November 2009

Appendix B

Related Documents

This appendix provides links to reference documents you can use to gain a more complete understanding of the technologies used in your NETGEAR product.

Document

Link

Windows XP and Vista Wireless

http://documentation.netgear.com/reference/enu/winzerocfg/index.htm

Configuration Utilities

 

Internet Networking and TCP/IP

http://documentation.netgear.com/reference/enu/tcpip/index.htm

Addressing

 

Wireless Communications

http://documentation.netgear.com/reference/enu/wireless/index.htm

Preparing a Computer for

http://documentation.netgear.com/reference/enu/wsdhcp/index.htm

Network Access

 

Virtual Private Networking (VPN)

http://documentation.netgear.com/reference/enu/vpn/index.htm

Glossary

http://documentation.netgear.com/reference/enu/glossary/index.htm

Related Documents

B-1

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

B-2

Related Documents

v1.1, November 2009

Appendix C

Command Line Reference

The ProSafe Dual Band Wireless-NAccess Point WNDAP350 can be configured either through the command line interface (CLI), a Web browser, or an MIB browser. The CLI allows viewing and modification of the configuration from a terminal or PC through a telnet connection.

Command Sets

keyword

Description

--------------------------------------

----------------------

|-backup-configuration

--backupconfiguration

|-config>

--configurationsetting

| |-apname

--accesspoint name

| |-country

--country/region

| |-dhcp>

--DHCPserver

| | |-dns-server

--DNSserver

| | |-gateway

--defaultgateway

| | |-ip-address

--IPrange

| | |-lease-time

--leasetime

| | |-status

--status

| | |-subnet-mask

--subnetmask

| | |-wins-server

--WINSserver

| |

 

| |-http-redirect

--enableHTTP redirection

| |-http-redirect-url

--HTTPredirection URL

| |-interface>

--selectwireless lan interface

| | |-wlan>

--wirelessLAN interface setting

| | | |-2.4GHz>

--2.4GHz wireless LAN interface setting

| | | | |-aggregation-length

--aggregatedpacket size

| | | | |-ampdu

--aggregatedMAC Protocol Data Unit

| | | | |-beacon-interval

--wirelessbeacon period in TU(1024 us)

| | | | |-channel

--wirelesschannel (depends on country

and wireless mode)

 

| | | | |-channelwidth

--wirelesschannel width

| | | | |-dtim-interval

--wirelessDTIM period in beacon interval

| | | |

|-extension-protection-spacing--wireless

extension protection spacing

|

| | |

|-fragmentation-length

--wireless

fragmentation threshold(even

only)

 

 

 

|

| | |

|-guardinterval

--interval

(from interference from other

 

 

 

Command Line Reference

 

C-1

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

transmissions)

 

 

 

| | | | |-knownap-add

 

 

--addknown access point

| | | | |-knownap-del

 

--deleteknown access point

| | | | |-macacl-add

 

 

--addwireless access control (ACL)

| | | | |-macacl-database

 

 

--deletewireless access control (ACL)

database

 

 

 

 

| | | | |-macacl-del

 

 

--deletewireless access control (ACL)

| | | | |-mcsrate

 

 

--transmitdata rate

| | | | |-mode

 

 

--enablewireless access control (ACL)

| | | | |-operation-mode

 

 

--wirelessoperation mode

| | | | |-power

 

 

--wirelesstransmit power

| | | | |-preamble

 

 

--wirelesspreamble (only effect on

802.11b

rates)

 

 

 

| | | | |-radio

 

 

--enablewireless radio

| | | | |-rate

 

 

--wirelesstransmission date rate

| | | | |-rifs-transmission

 

--enablesuccessive frame transmission at

different transmit powers

 

 

 

| | | | |-rogue-ap-detection

 

--enablerogue access point detection

| | | | |-rts-threshold

 

 

--wirelessRTS/CTS threshold

| | | | |-security-profile>

 

--createsecurity profile

| | | | | |-1>

 

 

--1stsecurity profile

| | | | | | |-authentication

 

--authenticationtype

| | | | | | |-encryption

 

 

--dataencryption

| | | | | | |-hide-network-name

 

--hidenetwork name

| | | | | | |-key1

 

 

--wirelesswep key 1

| | | | | | |-key2

 

 

--wirelesswep key 2

| | | | | | |-key3

 

 

--wirelesswep key 3

| | | | | | |-key4

 

 

--wirelesswep key 4

| | | | | | |-keyno

 

 

--keynumber

| | | | | | |-name

 

 

--profilename

| | | | | | |-presharedkey

 

--pre-sharedkey

| | | | | | |-security-separation

--disableassociated wireless client

communication

 

 

 

| | | | | | |-ssid

 

 

--networkname(1-32chars)

| | | | | | |-status

 

 

--profilestatus

| | | | | | |-vlan-id

 

 

--VLANid

| | | | | | |-wep-pass-phrase

 

--wirelesswep passphrase key

| | | | | | |-wepkeytype

 

 

--wirelesswep key type

| | | | | |

 

 

 

| | | | | |-2>

 

--2ndsecurity profile

| | | | | | |-authentication

 

--authenticationtype

| | | | | | |-encryption

 

 

--dataencryption

| | | | | | |-hide-network-name--hidenetwork name

| | | | | | |-key1

--wirelesswep key 1

| | | | | | |-key2

--wirelesswep key 2

| | | | | | |-key3

--wirelesswep key 3

| | | | | | |-key4

--wirelesswep key 4

| | | | | | |-keyno

 

 

--keynumber

 

 

 

 

 

C-2

 

 

 

Command Line Reference

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

| | | | | | |-name

 

--profilename

| | | | | | |-presharedkey

 

--pre-sharedkey

| | | | | | |-security-separation--disableassociated wireless client

communication

 

 

| | | | | | |-ssid

 

--networkname(1-32chars)

| | | | | | |-status

--profilestatus

| | | | | | |-vlan-id

 

--VLANid

| | | | | | |-wep-pass-phrase

--wirelesswep passphrase key

| | | | | | |-wepkeytype

 

--wirelesswep key type

| | | | | |

 

 

| | | | | |-3>

 

--3rdsecurity profile

| | | | | | |-authentication

--authenticationtype

| | | | | | |-encryption

 

--dataencryption

| | | | | | |-hide-network-name

--hidenetwork name

| | | | | | |-key1

 

--wirelesswep key 1

| | | | | | |-key2

 

--wirelesswep key 2

| | | | | | |-key3

 

--wirelesswep key 3

| | | | | | |-key4

 

--wirelesswep key 4

| | | | | | |-keyno

 

--keynumber

| | | | | | |-name

 

--profilename

| | | | | | |-presharedkey

 

--pre-sharedkey

| | | | | | |-security-separation--disableassociated wireless client

communication

 

 

| | | | | | |-ssid

 

--networkname(1-32chars)

| | | | | | |-status

--profilestatus

| | | | | | |-vlan-id

 

--VLANid

| | | | | | |-wep-pass-phrase

--wirelesswep passphrase key

| | | | | | |-wepkeytype

 

--wirelesswep key type

| | | | | |

 

 

| | | | | |-4>

 

--4thsecurity profile

| | | | | | |-authentication

--authenticationtype

| | | | | | |-encryption

 

--dataencryption

| | | | | | |-hide-network-name

--hidenetwork name

| | | | | | |-key1

 

--wirelesswep key 1

| | | | | | |-key2

 

--wirelesswep key 2

| | | | | | |-key3

 

--wirelesswep key 3

| | | | | | |-key4

 

--wirelesswep key 4

| | | | | | |-keyno

 

--keynumber

| | | | | | |-name

 

--profilename

| | | | | | |-presharedkey

 

--pre-sharedkey

| | | | | | |-security-separation--disableassociated wireless client

communication

 

 

| | | | | | |-ssid

 

--networkname(1-32chars)

| | | | | | |-status

 

--profilestatus

| | | | | | |-vlan-id

 

--VLANid

| | | | | | |-wep-pass-phrase

--wirelesswep passphrase key

| | | | | | |-wepkeytype

 

--wirelesswep key type

| | | | | |

 

 

 

 

 

Command Line Reference

 

C-3

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

| | | | | |-5>

--5thsecurity profile

| | | | | | |-authentication

--authenticationtype

| | | | | | |-encryption

--dataencryption

| | | | | | |-hide-network-name

--hidenetwork name

| | | | | | |-key1

--wirelesswep key 1

| | | | | | |-key2

--wirelesswep key 2

| | | | | | |-key3

--wirelesswep key 3

| | | | | | |-key4

--wirelesswep key 4

| | | | | | |-keyno

--keynumber

| | | | | | |-name

--profilename

| | | | | | |-presharedkey

--pre-sharedkey

| | | | | | |-security-separation--disableassociated wireless client

communication

 

| | | | | | |-ssid

--networkname(1-32chars)

| | | | | | |-status

--profilestatus

| | | | | | |-vlan-id

--VLANid

| | | | | | |-wep-pass-phrase

--wirelesswep passphrase key

| | | | | | |-wepkeytype

--wirelesswep key type

| | | | | |

 

| | | | | |-6>

--6thsecurity profile

| | | | | | |-authentication

--authenticationtype

| | | | | | |-encryption

--dataencryption

| | | | | | |-hide-network-name

--hidenetwork name

| | | | | | |-key1

--wirelesswep key 1

| | | | | | |-key2

--wirelesswep key 2

| | | | | | |-key3

--wirelesswep key 3

| | | | | | |-key4

--wirelesswep key 4

| | | | | | |-keyno

--keynumber

| | | | | | |-name

--profilename

| | | | | | |-presharedkey

--pre-sharedkey

| | | | | | |-security-separation--disableassociated wireless client

communication

 

| | | | | | |-ssid

--networkname(1-32chars)

| | | | | | |-status

--profilestatus

| | | | | | |-vlan-id

--VLANid

| | | | | | |-wep-pass-phrase

--wirelesswep passphrase key

| | | | | | |-wepkeytype

--wirelesswep key type

| | | | | |

 

| | | | | |-7>

--7thsecurity profile

| | | | | | |-authentication

--authenticationtype

| | | | | | |-encryption

--dataencryption

| | | | | | |-hide-network-name

--hidenetwork name

| | | | | | |-key1

--wirelesswep key 1

| | | | | | |-key2

--wirelesswep key 2

| | | | | | |-key3

--wirelesswep key 3

| | | | | | |-key4

--wirelesswep key 4

| | | | | | |-keyno

--keynumber

| | | | | | |-name

--profilename

 

 

C-4

Command Line Reference

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

| | | | | | |-presharedkey

--pre-sharedkey

| | | | | | |-security-separation--disableassociated wireless client

communication

 

| | | | | | |-ssid

--networkname(1-32chars)

| | | | | | |-status

--profilestatus

| | | | | | |-vlan-id

--VLANid

| | | | | | |-wep-pass-phrase

--wirelesswep passphrase key

| | | | | | |-wepkeytype

--wirelesswep key type

| | | | | |

 

| | | | | |-8>

--8thsecurity profile

| | | | | | |-authentication

--authenticationtype

| | | | | | |-encryption

--dataencryption

| | | | | | |-hide-network-name

--hidenetwork name

| | | | | | |-key1

--wirelesswep key 1

| | | | | | |-key2

--wirelesswep key 2

| | | | | | |-key3

--wirelesswep key 3

| | | | | | |-key4

--wirelesswep key 4

| | | | | | |-keyno

--keynumber

| | | | | | |-name

--profilename

| | | | | | |-presharedkey

--pre-sharedkey

| | | | | | |-security-separation--disableassociated wireless client

communication

 

| | | | | | |-ssid

--networkname(1-32chars)

| | | | | | |-status

--profilestatus

| | | | | | |-vlan-id

--VLANid

| | | | | | |-wep-pass-phrase

--wirelesswep passphrase key

| | | | | | |-wepkeytype

--wirelesswep key type

| | | | | |

 

| | | | |

 

| | | | |-wireless-bridge>

--wirelessbridge setting

| | | | | |-security-profile>

--createsecurity profile

| | | | | | |-1>

--1stsecurity profile

| | | | | | | |-authentication

--authenticationtype

| | | | | | | |-encryption

--dataencryption

| | | | | | | |-name

--profilename

| | | | | | | |-presharedkey

--presharedkey

| | | | | | | |-remote-mac

--remoteMAC

| | | | | | | |-status

--profilestatus

| | | | | | | |-wep-pass-phrase--wirelesswep passphrase key

| | | | | | | |-wepkey

--wirelesswep key

| | | | | | | |-wepkeytype

--wirelesswep key type

| | | | | | |

 

| | | | | | |-2>

--2ndsecurity profile

| | | | | | | |-authentication

--authenticationtype

| | | | | | | |-encryption

--dataencryption

| | | | | | | |-name

--profilename

| | | | | | | |-presharedkey

--presharedkey

| | | | | | | |-remote-mac

--remoteMAC

 

 

Command Line Reference

C-5

v1.1, November 2009

ProSafe Dual Band Wireless-NAccess Point WNDAP350 Reference Manual

| | | | | | | |-status

 

--profilestatus

| | | | | | | |-wep-pass-phrase

--wirelesswep passphrase key

| | | | | | | |-wepkey

 

--wirelesswep key

| | | | | | | |-wepkeytype

 

--wirelesswep key type

| | | | | | |

 

 

 

| | | | | | |-3>

 

--3rdsecurity profile

| | | | | | | |-authentication

--authenticationtype

| | | | | | | |-encryption

 

--dataencryption

| | | | | | | |-name

 

--profilename

| | | | | | | |-presharedkey

 

--presharedkey

| | | | | | | |-remote-mac

 

--remoteMAC

| | | | | | | |-status

 

--profilestatus

| | | | | | | |-wep-pass-phrase

--wirelesswep passphrase key

| | | | | | | |-wepkey

 

--wirelesswep key

| | | | | | | |-wepkeytype

 

--wirelesswep key type

| | | | | | |

 

 

 

| | | | | | |-4>

 

--4thsecurity profile

| | | | | | | |-authentication

--authenticationtype

| | | | | | | |-encryption

 

--dataencryption

| | | | | | | |-name

 

--profilename

| | | | | | | |-presharedkey

 

--presharedkey

| | | | | | | |-remote-mac

 

--remoteMAC

| | | | | | | |-status

 

--profilestatus

| | | | | | | |-wep-pass-phrase

--wirelesswep passphrase key

| | | | | | | |-wepkey

 

--wirelesswep key

| | | | | | | |-wepkeytype

 

--wirelesswep key type

| | | | | | |

 

 

 

| | | | | |

 

 

 

| | | | |

 

 

 

| | | | |-wmm>

 

--wmmsettings

| | | | | |-ap-data0-best-effort

--accesspoint best effort voice data

| | | | | |-ap-data1-background

--accesspointlow-prioritydata

| | | | | |-ap-data2-video

 

--accesspoint video data

| | | | | |-ap-data3-voice

 

--accesspoint voice data

| | | | | |-station-data0-best-effort

--stationbest effort voice data

| | | | | |-station-data1-background

--stationlow-prioritydata

| | | | | |-station-data2-video

--stationvideo data

| | | | | |-station-data3-voice

--stationvoice data

| | | | | |-support

 

--support

| | | | |

 

 

 

| | | |

 

 

 

| | | |-5GHz>

--5GHz wireless LAN interface setting

| | | | |-aggregation-length

 

--aggregatedpacket size

| | | | |-ampdu

 

--aggregatedMAC Protocol Data Unit

| | | | |-beacon-interval

 

--wirelessbeacon period in TU(1024 us)

| | | | |-channel

 

--wirelesschannel (depends on country and

wireless mode)

 

 

 

| | | | |-channelwidth

 

--wirelesschannel width

 

 

 

 

C-6

 

 

Command Line Reference

v1.1, November 2009