Loading...Install the Switch
To install your switch on a flat suface, you do not need any special tools. Be sure the switch is positioned with at least 2 inches of space on all sides for ventilation.
To install the switch in a rack, first attach the mounting brackets to the side of the switch. Insert the screws provided in the rack mount kit through each bracket mounting hole in the switch. Tighten the screws with a #1 Phillips screwdriver to secure each bracket. AUgn the mounting holes in the brackets with the holes in the rack and insert two pan-head screws with nylon washers through each bracket and into the rack. Tighten the screw with a #2 Phillips screwdriver to secure the switch in the rack.
Connect the Devices
To connect devices to the switch:
1. Connect the devices to the 10/100/1000 Mbps ports on the switch, using Category 5 UTP cable and an RJ-45 Plug.
Note: Ethernet specifications limit the cable length between your PC or server and the switch to 328 feet (100 meters) in length.
2.Connect one end of the DC power adapter cable to the power outlet on the rear panel of the swith and other end of the power adapter cable to wall outlet.
NETGEAR'
NETGEAR, Inc.
4500 Great America Parkway Santa Clara, CA 95054 http://www.NETGEAR.com
© 2005 by NETGEAR, Inc. All rights reserved.
Trademarks
NETGEAR, ProSafe, and Auto Uplink are registered trademarks of NETGEAR, Inc in the United States and other countries. All other trademarks and registered trademarks are the property of dieir respective owners.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliabili^,
NETGEAR reserves the right to make changes to the products to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or qiplication of the profuct(s) or circuit layout(s) described herein.
Certificate of the Manufacturer/Importer
By certified diat the NETGEAR Prosafe JGS524F Fast Ethernet Switch has been
suppressed in accordance with the confitions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordace with the regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating instructions.
Federal Office for Tdecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series fot compliance with the regulations.
Voluntary Control Council for Interference (VCCI) Statement
EN 55 022 Declaration of Conformance
This is to certify that the NETGEAR Prosafe JGSS24F Fast Ethernet Switch is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN3S 022 Class A (CISPR 22).
Federal Communications Commission (FCC) Compliance Notice:
Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Opmation is subject to the followng two conditions:
•This device may not cause harmful interfemece.
•This device must accq>t any interfemce received, including intrfemce that may cause undesired operation. Note: This equipment has been tested and fotmd to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interferences in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interferences to radio communications. However, there is no guarantee that interference wiU not occur in a particular installation if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct die interference by one or more of the following measures.
-Reorient or relocate the receiving antenna.
-hicrease the separation between die equipment and receiver.
-Connect die equipment into an outiet on a circuit different fixim diat to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
Canadian Department of Communications Radio inerference Reguiations
This digital apparatus (NETGEAR Prosafe JGS524F Fast Ethernet Switch ) does not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio rnterference Regulations o f the ranndian Department of GfimnniniRatinna.
Céfiement sur ie brouillage radioélectrique du mimistére des Communications
Cet pareil numérique (NETGEAR Prosafe JGS524F Fast Ediemet Switch ) re^ecte les limites de bruits radioélectriques visant les appareils numériques de class A tpescrites dans le Reglement sur le brouillage radioélectrique du mimisére des Communications du Canada.
NETGEAR*
JGS
ProSafe 10/100/1000 Switch W/SFP slots Installation Guide
e
20 0521-
Loading...