Nemco Food Equipment ShrimpPro 2000 Operations Manual

SPARE AND REPLACEABLE PARTS

S

Printed 8/09 Printed in U.S.A.

The only ShrimpPro user-replaceable parts are those in
the shrimp cutting area. While the Blade is made from
long-lasting, hardened stainless steel, it will begin to lose
its effectiveness in time and start tearing rather than
cutting shrimp. Do not attempt to sharpen as Blade will
lose its hardness. Replacement Blades may be ordered
from The NEMCO factory. (See phone, fax and address
below.) Having at least one spare on hand, stored in a
secure and accessible place, will avoid downtime.

Generally, the other components in the cutting area will
not require replacement. However, it is possible for the
Feeder Discs to eventually become too smooth to
reliably grasp all sizes of shrimp. Replacements may be
ordered. We can also provide a new part to replace any
component that is lost or damaged.

number and the nature of the problem (the “Claim
Information”).

(2) The Nemco Customer Service Department will

decide on the most appropriate course of action. If
Nemco determines that it must inspect a product,
the following procedure will be followed.

The end user will obtain a Return Goods Authorization
number from Nemco Customer Service to return the
product to Nemco for inspection. Please be sure to use
this number on the box and on paperwork sent with the
unit. Return the unit to Nemco. The Nemco Service
Department will determine if the problem is covered by
the foregoing warranty. If so, Nemco will repair the unit
and return it to the end user. If the unit is determined not
to be covered by the foregoing warranty, the dealer will
be contacted to determine the next course of action.

PRODUCT SERVICE

The ShrimpPro is inherently very reliable and, because
of its rugged construction, should require little or no
service throughout its lifetime. However, if service is ever
needed, it must be performed at the factory or by an
authorized service center. Any attempt to effect repair
without permission or guidance from the manufacturer
may invalidate the warranty and could be dangerous.

ShrimpPro PRODUCT WARRANTY
REGISTRATION

To validate your warranty, it is important that you fill in
and return the Warranty Certificate promptly. When
completed mail to:

NEMCO Food Equipment, Ltd.

301 Meuse Argonne

Hicksville, OH 43526
Nemco has a staffed service department and we
believe prompt service is extremely important to our
customers. Therefore, we request all product service
inquiries be handled in the following manner:

(1) The end user should call Nemco Customer Service

with the company name, address, phone number,
model number, serial number (if applicable), Nemco
Sales Order number or Dealer Purchase Order

ShrimpPro SPECIFICATIONS

Manufactured by NEMCO Food Equipment, Ltd.
Model No.: 55925
Power: 120 V.A.C., 60 Hz, 1 Amp

240 V.A.C., 50Hz, 0.5 Amp
Shipping Weight: 18 lbs.
U.S. and Foreign Pats.

PRODUCT WARRANTY

Except as otherwise provided below, Nemco Food Equipment, Ltd. ("Nemco") warrants, to the original user, its electrical food preparation products (other than
blades and light bulbs) to be free of electrical and mechanical defects in material and workmanship under "normal use" (defined below) for the shorter of the
following periods: (a) one (1) year from the date placed in service by the original user, or (b) 18 months from the date of shipment from its factory. In addition,
Nemco warrants its non-electrical food preparation products (other than blades) to be free of mechanical defects in material and workmanship under normal use
for two (2) years from the date placed in service by the original user. The warranty provided for herein shall be limited to parts and labor. Any determination
that a product is defective or covered by this warranty, shall be made by Nemco, in its sole discretion. The determination of whether to repair or replace a
defective, covered product, or to refund the purchase price for the product, will be at Nemco’s sole discretion. This warranty does not cover products used outside
the United States, or damages caused by accident, misuse, negligence of any person other than Nemco, current or voltage other than stated on the appliance,
fire, flood or other casualty. Any alteration to the product or unauthorized repair voids this warranty. For purposes of this warranty, the phrase, "normal use" shall
mean the use of the product in connection with food in accordance with the product manual accompanying the product.

Nemco shall be responsible only for repairs or replacements of defective parts performed by Nemco’s authorized service personnel. Authorized service agencies
are located in principal cities throughout the continental United States, Alaska and Hawaii.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. NEMCO EXPRESSLY DISCLAIMS ANY
IMPLIED WARRANTY THAT ANY OF ITS PRODUCTS IS MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE, OR DOES NOT INFRINGE ON THE RIGHTS OF
ANY THIRD PARTY. THE FOREGOING WARRANTY SHALL BE NEMCO’S SOLE AND EXCLUSIVE OBLIGATION. ANY PERSON’S (BUYER, USER OR OTHERWISE)
EXCLUSIVE REMEDY AGAINST NEMCO, AND NEMCO’S SOLE OBLIGATION, FOR ANY AND ALL CLAIMS, WHETHER FOR BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING WITHOUT LIMITATION NEGLIGENCE), OR OTHERWISE, SHALL BE LIMITED TO NEMCO REPAIRING OR REPLACING THE
PRODUCT, OR, AT NEMCO’S OPTION, REFUNDING THE PURCHASE PRICE THEREFOR. IN NO EVENT SHALL NEMCO HAVE ANY LIABILITY FOR DAMAGES
IN AN AMOUNT EXCEEDING THE PURCHASE PRICE OF THE PRODUCT
CONSEQUENTIAL DAMAGES. Any person desiring to make any claim against Nemco must do so within six (6) months after expiration of the applicable warranty

period, or such claim shall be forever barred.

, NOR SHALL NEMCO HAVE ANY LIABILITY FOR INCIDENTAL, SPECIAL OR

NEMCO Food Equipment, Ltd.

301 Meuse Argonne

®

Hicksville, Ohio 43526
Phone [phone]
Fax [phone]
Toll Free [phone]
www.nemcofoodequip.com

Printed 10/08 Printed in U.

1

IMPORTANT SAFEGUARDS

123

4

56789

10

11

47137

55981

45184

46959

46960

46961

55970

46328

56017

55979

55974

56016

45409

Depth Adjustment Knob

Cutting Guard

Cutting Guard Washer

Depth Cut Roller (Medium)

Depth Cut Roller (Large)

Depth Cut Roller (Small)

Idler Shaft

Retainer Spring

Jam Nut

Female Feeder Disc

Male Feeder Disc

Pipe Thread Nut

Shaft Seal

12131415161718192021222324

45073

55976

55977

55976

56009

55969

55961

55973

55968

47488

46069

46698

45180

Hex Nut, 3/8 - 16

Blade Support Washer

Cutting Blade

Blade Support Washer

Blade Holder Nut

Front Plate

Feeder Disk Shaft

Top Housing

Bottom Housing

Motor

Thread Cutting Nut

Screw, #10 - 32 x 3/8”

Washer, #10 Lock

25262728293031323334353637

46666

46949

46665

46663

46958

46955

46956

46957

47481

47482

55983

46953

55960

Screw, #10 - 16 x 1”

Leg

Screw, #8 x 3/4”

Screw, #10 x 3/8”

Cable Clamp

Drive Pulley (Large)

Drive Pulley (Small)

Drive Belt

Cordset

Power Switch

Rectifier

Bearing

Mounting Bracket

Parts List

• READ ALL INSTRUCTIONS

• NEVER immerse the power unit in water or

other liquid. Severe electrical shock can result.

• CLOSELY SUPERVISE nearby children when

using ShrimpPro.

• DO NOT operate the ShrimpPro outdoors.

• DO NOT attempt to operate the ShrimpPro if

the unit has been dropped or if power cord or
power plug have been damaged. Return it for
repair. (See SERVICE.) There are no user
serviceable parts.

• DO NOT operate when wearing loose clothing

or accessories (bracelet, neck chain, necktie,
scarf, etc.). These could be caught by the
rotating Discs and cause injury. Loose hair
should be pulled back and secured.

• MAKE SURE that the power cord is unplugged

before removing Cutting Guard.

• AVOID touching the moving Discs. They could

grab your fingers and draw them into the cutter.

• THE SHRIMPPRO is equipped with a power

cord with a three-blade plug. Plug this ONLY
into a matching 120 volt A.C. three-blade outlet.
DO NOT cut off the third blade or attempt to
use with a two-blade extension cord. If you are
too far from the outlet, use a three-wire

extension cord of adequate power rating (see
specifications), obtainable at almost any
hardware store.

• UNPLUG the machine when not in use, before

attempting to clean, when changing Blades or
when making any adjustments to the Discs.
Pull only on the plug, never on the cord.

• MAKE SURE that the power switch is in the

‘OFF’ position before plugging-in or unplugging
the power cord.

• DO NOT attempt to use with unauthorized

attachments or for any application other than
that for which the unit was designed. Such
use could create a hazardous situation or
cause personal injury to the user.

• DO NOT operate on or near hot surfaces or

appliances used for cooking.

• DO NOT let power cord hang over edge of

table or counter.

• WHEN NOT IN USE, store the unit in a safe

place where it will not be a hazard to
passers-by.

• ALWAYS store with Cutting Guard securely

attached so that the blade is covered for safety.

• NEVER attempt to lift ShrimpPro by its Cutting

Guard. Always lift from under the base.

SAVE THESE INSTRUCTIONS

INSTRUCTIONS FOR USE & CARE

UNPACKING

When you open the shipping container, you will find
that the ShrimpPro is fully assembled and ready to
cut medium-sized shrimp (16/20 to 36/40). In the
carton, you will also find two Depth Cut Rollers,
differing in width. If you wish to cut small or large
shrimp, you must replace the already mounted
medium Roller (Item number 4 in the exploded view
drawing of Page 7) with the appropriate alternate
(the wider Roller for larger shrimp and the narrow
one for small shrimp). The procedure for
replacement is given on page 3.

Two 9/16” open end wrenches, used for Cutting
Blade replacement or cleaning, and a bottle

of lubricant with a dropper top are also packed with
the ShrimpPro. This is a food-grade lubricant which
is approved for incidental contact with food.

Examine the ShrimpPro for possible shipping
damage. Remove the Cutting Guard and inspect
cutting area components (see exploded view
drawing). The Cutting Guard (Item number 2)
may be removed by first unscrewing the Depth
Adjustment Knob (Item 1) and then pulling the
Guard away from and off of the machine.
When removing the Guard, make sure that the
Adjustment Knob Washer (Item 3) remains on
the Guard (Item 2). If any damage is noted,
immediately notify both the shipping company
and the manufacturer.

2

7