NEC NP-PX800X2-08ZL, NP-PX750U2-18ZL, NP-PX800X, NP-P501X, NP-P451W User Manual

...

0 (0)

======================================================================

Control Commands for NEC Projector (Basic) Rev 08.04.14a

----------------------------------------------------------------------

Updated on August 4, 2014

----------------------------------------------------------------------

This file contains information about NEC projector control commands.

======================================================================

Model Name

GT60	GT5000/GT6000 Series
GT50	GT1150/GT2150 Series
HT	HT1000/HT1100 Series
HT10	HT410/HT510 Series
LT180	LT180
LT30	LT25/LT30/LT35 Series
LT	LT220/LT240/LT240K/LT260/LT260K/LT245/LT265 Series
LT80	LT280/LT380 Series
MT70	MT860/MT1060/MT1065/MT1075 Series
NP60	NP40/NP50/NP60 Series
NP62	NP41/NP61/NP62 Series
NP1000	NP1000/NP2000 Series
NP3150	NP1150/NP2150/NP3150/NP3151W Series
NP4000	NP4000/NP4001 Series
NP905	NP905/NP901W/VT800 Series
NP600	NP300/NP400/NP500/NP500W/NP500WS/NP600/NP600S Series
VT	VT770 Series
VT70	VT37/VT47/VT480/VT57/VT570/VT575/VT670/VT676 Series
VT80	VT48/VT480/VT580 Series
VT90	VT49/VT490/VT590/VT595/VT695 Series
VT700	VT700
WT	WT600/WT610/WT615 Series
NP4100	NP4100/NP4100W Series
NP3250	NP1250/NP2250/NP3250/NP3250W Series
NP610	NP310/NP410/NP410W/NP510/NP510W/NP510WS/NP610/NP610S Series
NP2200	NP1200/NP2200 Series
NP216	NP110/NP115/NP215/NP216 Series
NP64	NP43/NP64 Series
M300	M260X/M260W/M300X/M300W Series
M361	M271X/M311X/M311W/M361X Series
M402	M282X/M322X/M322W/M402X/M332XS/M352WS
P420	P350X/P350W/P420X Series
P501	P401W/P451X/P451W/P501X Series
PE401	PE401H
UM330	UM330X/UM330W Series
U300	U300X/U310W Series
V300	V260/V260X/V300X/V300W Series
VE281	VE281/VE281X/VE282B/VE282XB
PA600	PA600X/PA550W/PA500U/PA500X Series
PX750U	PX700W/PX750U/PX800X Series
PH1000U	PH1000U Series
PH1400U	PH1400U Series
Contents

1.Projector Control

2.Connection Method

3.Interface Conditions

4.List of Commands

5.Command Descriptions

6.Table of Response Error Codes

======================================================================

1. Projector Control

----------------------------------------------------------------------

NEC projectors make use of control commands that control the functions of the projector via connection with a personal computer or another device.

======================================================================

2. Connection Method

----------------------------------------------------------------------

The following 3 kinds of connection methods are available for sending and receiving control commands.

1.Serial connection using the serial port on the projector A serial cable is required.

2.USB connection using the USB port on the projector A USB cable is required.

3.LAN connection

3-1. LAN connection using a wired LAN card

A wired LAN card and LAN cable are required. 3-2. LAN connection using a wireless LAN card

A wireless LAN card is required.

3-3.LAN connection using the LAN port on the projector A LAN cable is required.

3-4. LAN connection using a wireless LAN unit A wireless LAN unit is required

Status of supported connection

	(1)	(2)	(3-1)	(3-2)	(3-3)	(3-4)
	Serial Port	USB Port	Wired	Wireless	Wired	Wireless
	Serial Port	USB Port	LAN Card	LAN Card	LAN Port	LAN Port
			LAN Card	LAN Card	LAN Port	LAN Port

GT5000/GT6000	Yes	Yes	Yes	Yes	Yes	No

GT1150/GT2150	Yes	No	Yes	Yes	Yes	No

HT410/HT510	Yes	No	No	No	No	No

HT1000/HT1100	Yes	No	No	No	No	No

LT180	Yes	No	No	No	No	No

LT25/LT30/LT35	Yes	No	No	No	No	No

LT220/LT240/LT260	Yes	No	Yes	Yes	No	No

LT240K/LT260K	Yes	Yes	Yes	Yes	No	No

LT245/LT265/LT280/LT380	Yes	No	No	Yes	Yes	No

MT860/MT1060/MT1065/MT1075	Yes	Yes	Yes	Yes	No	No

NP40/NP50/NP60	Yes	No	No	No	No	No

NP41/NP61/NP62	Yes	No	No	No	No	No

NP43/NP64	Yes	No	No	No	No	No

NP1000/NP2000	Yes	No	No	Yes	Yes	No

NP1150/NP2150/NP3150/NP3151W	Yes	No	No	No	Yes	Yes

NP4000/NP4001	Yes	No	No	No	Yes	No

NP905/NP901W	Yes	No	No	No	Yes	Yes

NP300/NP400/NP500/NP500W/NP500WS/NP600/NP600S	Yes	No	No	No	Yes	No

VT770	Yes	No	No	No	No	No

VT37/VT47/VT470/VT57/VT570/VT575VT/670/VT676	Yes	No	No	No	No	No

VT48/VT480/VT580	Yes	No	No	No	No	No

VT49/VT490/VT590/VT595/VT695/VT700	Yes	No	No	No	No	No

VT700	Yes	No	No	No	No	No

VT800	Yes	No	No	No	Yes	No

WT600WT/610/WT615	Yes	Yes	Yes	Yes	No	No

NP4000/NP4001	Yes	No	No	No	Yes	No

NP1250/NP2250/NP3250/NP3250W	Yes	No	No	No	Yes	Yes

NP310/NP410/NP410W/NP510/NP510W/NP510WS/NP610/NP610S	Yes	No	No	No	Yes	No

NP1200/NP2200	Yes	No	No	No	Yes	No

NP4100/NP4100W	Yes	No	No	No	Yes	No

NP110/NP115/NP215/NP216	Yes	No	No	No	Yes	No

M260X/M260W/M300X/M300W	Yes	No	No	No	Yes	Yes

M271X/M311X/M311W/M361X	Yes	No	No	No	Yes	Yes

M282X/M322X/M322W/M402X?M332XS?M352WS	Yes	No	No	No	Yes	Yes

P350X/P350W/P420X	Yes	No	No	No	Yes	Yes

P401W/P451X/P451W/P501X	Yes	No	No	No	Yes	Yes

PE401H	Yes	No	No	No	No	No

UM330X/UM330W	Yes	No	No	No	Yes	Yes

U300X/U310W	Yes	No	No	No	Yes	No

V260X/V300X/V300W	Yes	No	No	No	Yes	No

VE281/VE281X/VE282B/VE282XB	Yes	No	No	No	No	No

PA500X/PA550W/PA500U/PA600X	Yes	No	No	No	Yes	Yes

PX700W/PX750U/PX800X	Yes	No	No	No	Yes	Yes

PH1000U	Yes	No	No	No	Yes	Yes

PH1400U	Yes	No	No	No	Yes	Yes

Yes: Supported
No: Not Supported

*A USB cable is supplied as standard with the MT860/1060/1065/1075.

*The GT5000/6000 does not come with a USB cable.

*Note that a connection method using the supplied USB cable is not supported for the LT220/240/260.

*The serial cable, LAN card and LAN cable are separately sold.

*The WT610 replaced the WT610 and uses the same command set.

(CAUTION)

Before making connections, be sure to invalidate the standby mode of the projector and set the "idle mode". The projector cannot use the control commands in the standby mode.

Setting method: Under projector [Projector Options] --> [Setup], enter a check for [Idle Mode] on Page 4.

( CAUTION ) (!1)

Before making connections, be sure to select [NORMAL] for [STANDBY MODE].

Setting method : From the projector's menu, select [SETUP] --> [OPTIONS(2)] -->[STANDBY MODE]--> [NORMAL].

( CAUTION ) (!2)

The projector accept the "POWER ON" command during [POWER-SAVING] mode for[STANDBY MODE].

Supplement:

(!1) Only the NP600/NP610/NP3200 series is compatible. (!2) Only the M300 series is compatible.

[P350X/P350W/P420X Series]

STANDBY MODE: "POWER-

SAVING"

		Wired	Wireless
	Serial	LAN	LAN
Control Command	port	port	unit
POWER ON	Yes	No	No
Yes: Supported
No: Not supported

[P401W/P451W/P451W/P501X

Series] [PA600X/PA550W/PA500U/PA500X Series] [PX700W/PX750U/PX800X Series] [PH1000U Series]

STANDBY MODE: "POWER-

SAVING"

		Wired	Wireless
	Serial	LAN	LAN
Control Command	port	port	unit
POWER ON	Yes	No	No
STANDBY MODE: "NETWORK STANDBY"
		Wired	Wireless
	Serial	LAN	LAN
Control Command	port	port	unit
POWER ON	Yes	Yes	Yes
Yes: Supported
No: Not supported

====================================================================

3. Interface Conditions

----------------------------------------------------------------------

Serial connection

----------------------------------------------------------------------

The communications method conforms to the RS-232C standard.

*A USB cable is supplied as standard with the MT860/1060/1065/1075.

*The GT5000/6000 does not come with a USB cable.

*Note that a connection method using the supplied USB cable is not supported for the LT220/240/260.

*The serial cable, LAN card and LAN cable are separately sold.

( CAUTION )

Before making connections, set the standby mode of the projector to "NORMAL" or "Idol mode".

The projector cannot use the control commands in the power-saving condition, but the following model can use some control commands.

Baud rate:	38400 bps
	(NP600 series, NP610 Series, VT60/VT70/VT80/VT90 series, VT700: 19200bps)
Data length:	8 bits
Parity bit:	No parity
Stop bits:	1 bit
Communications mode:	Full duplex

The control connector is described below.

[ HT/LT/NP40/VT70/VT80/VT90/WT ]

The PC CONTROL connector is a mini DIN 8-pin connector.

1 To TxD of PC

4 To GND of PC

7 To RxD of PC

* 2, 3, 5, 6, and 8 are used inside the projector.

[ GT/LT80/MT/NP1000/VT (except

VT70/VT80/VT90)/NP3150/NP905/NP600/NP4000/NP3250/NP610/NP2200/NP216/M300/P420/U300/V300 ]

The PC CONTROL connector is a D-SUB 9-pin connector.

2To TxD of PC

3To RxD of PC

5To GND of PC

7To CTS of PC

8To RTS of PC

====================================================================

4. Communication Frame

----------------------------------------------------------------------

On the LT/MT/SX/GT series projectors communication is done in a frame composed of header, data, and checksum.

The frame sent from the controller to the projector is referred to as

a command, and the one sent from the projector to the command as an reply is referred to as a response.

The response has two types; Acknowledge (hereafter referred to as ACK) that recognizes a command and Negative Acknowledge (hereafter referred to as NAK) that fails to recognize a command.

+--------------		+	Command	+--------------	+
\|	\|--------------		>\|		\|
\| Controller		\|	\| Projector \|
\|	\|<--------------		\|		\|
+--------------		+	Response	+--------------	+

(ACK or NAK)

4-1. Frame Format

**********************************************************************

One frame comprises a header, a data portion, and a checksum.

Frame Format:
+-------------------------------						+----------------------			+--------		+
\|	Header portion					\|	Data portion			\|Checksum\|
\|				\|	(Max. 4095 Bytes)				\|		\|
+-----	+-----	+-----		+-------	+-----	+-----	+--	--+-------		+--------	+
\| 1 \| 2 \| 3 \| 4 \| 5 \| 6 \| ~ \| n \| m \|
+-----	+-----	+-----		+---+---+-----		+-----	+--	--+-------		+--------	+
\| 8 \| 8 \| 8 \| 4 \| 12 \| 8 \| ~ \| 8 \| 8 \|
\| Bit \| Bit \| Bit \|Bit\| Bit					\| Bit \|		~ \|	Bit \|	Bit	\|
+-----+-----+-----+---+---------						+-----+-- ~ --+-------				+--------	+
\|	\|	\|	\|	\|
\|	\|	\|	\|	+-------------		Data length
\|	\|	\|	+	--------------------			Model code
\|	\|	+-------------------------					Projector ID
\|	+-------------------------------						ID2
+-------------------------------------							ID1

* ID1: (8 Bit)

This is an identification data assigned to each command.

Command :

This sets an identification data assigned to each command to send it. ( See each command description.)

Response :

This returns the 6th bit of received ID1 as HIGH.

For ACK it sends the 8th bit back as LOW (recognized); for NAK it sends the 8th bit back as HIGH (not recognized).

* ID2: (8 Bit)

This is an identification data assigned to each command.

Command :

This sets an identification data assigned to each command to send it.

( See each command description.)

Response :

This returns the value of received ID2 as is.

* Projector ID : (8 Bit)

This is a projector ID for the projector that sends and receives frames.

Command :

This specifies a projector ID for the projector that sends and receives commands. (individual notification)

Entering 00H or FFH becomes a common command for all the projectors. (broadcast notification)

This is convenient for controlling multiple projectors at the same time.

*When the controller is connected with the projector on a one-to-one basis Broadcast notification is recommended.

*When the controller is connected with multiple projectors To control a certain projector, use "individual notification". For all others "broadcast notification" is recommended.

Response :

This returns the projector ID for a projector received regardless of individual notification or broadcast notification.

CAUTION :

To notify individually, specifying a model code from the following model codes is required.

* Model code: (4 Bit)

This is a model code for the projector that sends and receives frames.

Command :

This specifies a model code for the projector that sends commands. (individual notification)

Entering 0000B or 1111B becomes a common command for all the projectors. (broadcast notification)

This is convenient for controlling multiple projectors at the same time.

*When the controller is connected with the projector on a one-to-one basis Broadcast notification is recommended.

*When the controller is connected with multiple projectors To control a certain projector, use "individual notification". For all others "broadcast notification" is recommended.

Response :

This returns the model code for a projector received regardless of individual notification or broadcast notification.

Table of Model codes

-------------------------------------------

0000B	: (broadcast notification)
0001B	: MT Series
0010B	: LT Series
0011B	: SX Series
0101B	: GT Series

1111B : (broadcast notification)

CAUTION :

*When the model code is set to "broadcast notification", the command becomes broadcast notification command, regardless of values of the projector ID.

*Model code is specified using upper ranking 4 bits of data length. The lower ranking 4 bits becomes the upper bits of data length.

*Data length : (12 Bit)

This is data length of data portion (unit:: byte).

Command :

This sets data length of data added to a command to send it. ( See each command description.)

Response :

This sets data length of data added to a response to send it. ( See each command description.)

CAUTION :

Data length is specified using total of 12 bits ( 0 - 4095) of 4 bits of the 4th byte and 8 bits of the 5th byte.* The upper ranking 4 bits of the 4th byte is model code.

* Data portion

This becomes data of data length specified in the data length portion.

Command :

This sets data added to a command to send it. ( See each command description.)

Response :

This sets data added to a response to send it. ( See each command description.)

* Checksum

This is lower ranking 8 bits of the sum total of the header and data portions of one transmit and receive data frame.

4-2. Data portion of response

**********************************************************************

For ACK

This returns ACK without adding data portion to the command that does not request data.

This returns ACK with adding data to the data portion for the command that requests data.

For NAK

This adds a cause of not accepting the command to data portion to return it.

(Example) Power On

Command:

02H 00H FFH F0H 00H CKS

NAK:

A2H 00H 01H 20H 02H DATA01 DATA02 CKS

Data Contents

----------------------------------------------------------------------

DATA01 Error types

00H	: Not supported
01H	: Parameter error
02H	: Operation mode error
03H	: Gain-related error
04H	: Logo transfer error
DATA02	Error description

*When not supported 00H : Unknown command

01H : The current model does not support this function. 02H : This model is not compatible with the Switcher. 03H : This model is not compatible with the PC Viewer.

*When a parameter error occurs

00H : Unvalid values specified.

01H : Specified terminal is unavailable or cannot be selected 02H : Selected language is not available.

*When an operation mode error occurs 00H : Available memory reservation error 01H : External control working

02H : Operating memory

03H : Standby

04H : On Forced on-screen mute mode

05H : Link mode working

06H : Displaying a signal other than PC Viewer

07H : -No signal-

08H : Displaying a test pattern or PC Card Files screen. 09H : No PC card is inserted-

0AH : Memory operation failed 0BH : Switcher mode working 0CH : Displaying the Entry List

*When a gain adjustment error occurs

00H : Group number / sub category number is not correct. 01H : Selected gain is not available.

02H : Adjustment failed

* When a logo transfer error occurs 00H : Start is not requested

01H : Cannot process due to storing

02H : Exceeds the total number of blocks required at the time of start

03H : The block number of transferred data is not consecutive.

USB connection

----------------------------------------------------------------------

This conforms to the USB1.1 standard.

Transfer speed: All speeds (supported)

Endpoint: Control transfer Endpoint 0

Device class: HID class (Ver1.1)

USB1.1 Standard: Universal Serial Bus Specification Revision 1.1

HID : Human Interface Device

Connector Specifications

1 VBUS (Power supply)

2 D- (- Signal)

3 D+ (+ Signal)

4 GND (Ground)

* Depending on the USB host controller in the personal computer, the USB connection may fail to operate. When using a USB hub, please use a self-powered type, not a bus-powered type. When using a USB hub, connection to the first stage of the USB hub is recommended.

LAN connection

----------------------------------------------------------------------

[ Wired LAN port ]

LAN interface

Communication speed: Auto setting (10/100Mbps)

Certified standard: IEEE802.3 (10BASE-T)

IEEE802.3u (100BASE-TX, Auto-Negotiation)

A LAN connector (8 male RJ-45 connector)

1	TD+	Transmit data (+)
2	TD-	Transmit data (-)
3	RD+	Receive data (+)
4		Not used
5		Not used
6	RD-	Receive data (-)
7		Not used
8		Not used

[ Wired/wireless LAN card ]

The LAN connections will differ depending on the commercial LAN card that is used.

-For information on supported LAN cards, visit: Global: http://www.nec-pj.com/

[Port Number]

The TCP port number used is "7142".

====================================================================

4. List of Commands

----------------------------------------------------------------------
* Example for command
----------------------------------------------------------------------
Command name	Example
----------------------------------------------------------------------
006. RUNNING SENSE		00H 81H 00H 00H 00H	81H
007. COMMON DATA REQUEST		00H C0H 00H 00H 00H C0H
009. ERROR STATUS REQUEST		00H 88H 00H 00H 00H	88H
015. POWER ON		02H 00H 00H 00H 00H	02H
016. POWER OFF		02H 01H 00H 00H 00H	03H
018. INPUT SW CHANGE		02H 03H 00H 00H 02H	<DATA> CKS
020. PICTURE MUTE ON		02H 10H 00H 00H 00H	12H
021. PICTURE MUTE OFF		02H 11H 00H 00H 00H	13H

022. SOUND MUTE ON		02H	12H 00H 00H	00H	14H
023. SOUND MUTE OFF		02H	13H 00H 00H	00H	15H
024. ONSCREEN MUTE ON		02H	14H 00H 00H	00H	16H
025. ONSCREEN MUTE OFF		02H	15H 00H 00H	00H	17H
030. GAIN ADJUST		03H	10H 00H 00H	05H	<DATA> CKS
030-2. VOLUME ADJUST		03H	10H 00H 00H	05H	05H <DATA> CKS
030-12. IMAGE MODE ADJUST		03H	10H 00H 00H	05H	<DATA> CKS
037. INFORMATION REQUEST		03H	8AH 00H 00H 00H 8DH
037-1. LAMP INFORMATION REQUEST		03H	8CH 00H 00H 00H 8FH
037-2. LAMP INFORMATION REQUEST 2		03H	94H 00H 00H	00H	97H
037-4. LAMP INFORMATION REQUEST 3		03H	96H 00H 00H	02H	<DATA> CKS
037-6: CARBON SAVINGS INFORMATION REQUEST 03H			9AH 00H 00H 01H <DATA> CKS
037-7. LAMP INFORMATION REQUEST 4		03H	9BH 00H 00H 03H <DATA> CKS
038. LAMP MODE REQUEST		03H B0H 00H 00H 01H 07H BBH
039. LAMP MODE SET		03H B1H 00H 00H 02H 07H 00H BDH
046. WXGA MODE SETTING REQUEST		03H B0H 00H 00H 01H DATA1 CKS
049. WXGA MODE SETTING SET		03H B1H 00H 00H 02H DATA1 DATA2 CKS
050. REMOTE KEY CODE		02H	0FH 00H 00H 02H 00H 00H 13H
053. LENS CONTROL		02H	18H 00H 00H	02H	<DATA> CKS
053-1. LENS CONTROL REQUEST		02H	1CH 00H 00H 02H <DATA> CKS
053-2. LENS CONTROL 2		02H	1DH 00H 00H 04H <DATA> CKS
053-3. LENS MEMORY CUSTOM SET		02H	1EH 00H 00H 01H <DATA> CKS
053-4. LENS MEMORY REFERENCE SET		02H	1FH 00H 00H 01H <DATA> CKS
053-5. LENS MEMORY CONTROL REQUEST		02H	20H 00H 00H	01H	<DATA> CKS
053-6. LENS MEMORY CONTROL		02H	21H 00H 00H	02H	<DATA> CKS
053-7. LENS INFORMATION REQUEST		02H	22H 00H 00H	01H	<DATA> CKS
060. GAIN PARAMETER REQUEST 2		03H	04H 00H 00H	03H	<DATA> CKS
077. MUTE CONTROL		02H	1AH 00H 00H 02H <DATA> CKS
078-1. SETTING REQUEST		00H	85H 00H 00H	01H	00H CKS
078-2. RUNNING STATUS REQUEST		00H	85H 00H 00H	01H	01H CKS
078-3. INPUT STATUS REQUEST		00H	85H 00H 00H	01H	02H CKS
078-4. MUTE STATUS REQUEST		00H	85H 00H 00H	01H	03H CKS
078-5. MODEL NAME REQUEST		00H	85H 00H 00H	01H	04H CKS
078-6. MIRROR COVER STATUS REQUEST		00H	85H 00H 00H	01H	05H CKS
079. FREEZE CONROL		01H	98H 00H 00H	01H DATA01 CKS
097-198. PIP/SIDE BY SIDE REQUEST		03H B0H 00H 00H 02H C5H DATA CKS
098-196. WXGA MODE SETTING SET		03H B1H 00H 00H 02H DATA1 DATA2 CKS
098-198. PIP/SIDE BY SIDE SET		03H B1H 00H 00H 03H C5H <DATA> CKS
110. AUTO FUNCTIONS EXECUTE		03H B6H 00H 00H 01H <DATA> CKS
111. AUTO ADJUST EXECUTE2		03H BAH 00H 00H 01H <DATA> CKS
305-1. BASE MODEL TYPE REQUEST		00H BFH 00H 00H 01H <DATA> CKS
305-3. PROJECTOR INFORMATION REQUEST		00H BFH 00H 00H 01H <DATA> CKS
* Availability by Model
----------------------------------------------------------------------
Model No.
-------------------------
01	: LT240/LT260
02	: MT1060/MT1065/MT1075
03	: HT1000
04	: LT220
05	: MT860
06	: WT600/WT610/WT615
07	: GT5000
08	: LT240K/LT260K
09	: GT6000
10	: HT1100
11	: VT770
12: HT410/HT510 (HT10 Series)
13	: LT245/LT265
14	: LT280/LT380

15 : LT180

16 : VT37/VT47/VT470/VT57/VT570/VT575/VT670/VT676 (VT70 series)

17 : VT48/VT480/VT580 (VT80 Series)

18 : NP1000/NP2000 (NP1000 Series)

19 : NP1150/NP2150/NP3150/NP3151W (3150 Series)

20 : LT25/LT30/LT35 (LT30 Series)

21 : NP40/NP50/NP60 (NP60 Series)

22 : VT49/VT490/VT590/VT595/VT695 (VT90 Series)

23 : VT700

24:NP4000/NP4001 (NP4000 Series)

25:NP905/NP901W/VT800 (NP900 Series)

26:NP41/NP61/NP62 (NP62 Series)

27:NP300/NP400/NP500/NP500W/NP500WS/NP600/NP600S (NP600 Series)

28:GT1150/GT2150 (GT50 Series)

29:NP4100/NP4100W (NP4100 Series)

30:NP1250/NP2250/NP3250/NP3250W (NP3250 Series)

31:NP310/NP410W/NP510/NP510W/NP510WS/NP610/NP610S (NP610 Series)

32:NP1200/NP2200 (NP2200 Series)

33:NP110/NP115/NP215/NP216 (NP216 Series)

34:NP43/NP64 (NP64 Series)

35:M260X/M260W/M300X/M300W (M300 Series)

36:P350X/P350X/P420X (P420 Series)

37:U300X/U310W (U300 Series)

38:V260/V260X/V300X (V300 Series)

39:PA600X/PA550W/PA500U/PA500X (PA600 Series)

40:PX700W/PX750U/PX800X (PX750 Series)

41:PH1000U (PH1000 Series)

42:VE281/VE281X/VE282B/VE282XB (VE281 Series)

43:P401W/P451X/P451W/P501X (P501 Series)

44:UM330X/UM330W (UM330 Series)

45:M271X/M311X/M311W (M311 Series)

46:PE401H (P401 Series)

47:P401W/P451X/P451W/P501X (P501 Series)

48:M282X/M322X/M322W/M402X/M332XS/M352WS (M402 Series)

Meaning of Symbols

--------------------------------------------------------------------

* Supported

! Is available depending on model's version

- Not Supported

Availability by Model (CURRENT MODELS)

Command Name

006.

RUNNING SENSE

007.

COMMON DATA REQUEST

009.

ERROR STATUS REQUEST

015.

POWER ON

016.

POWER OFF

018.

INPUT SW CHANGE

020.

PICTURE MUTE ON

021.

PICTURE MUTE OFF

022.

SOUND MUTE ON

023.

SOUND MUTE OFF

024.

ONSCREEN MUTE ON

025.

ONSCREEN MUTE OFF

030.

GAIN ADJUST

030-2. VOLUME ADJUST

Volume

Bass

Treble

Balance

030-12. IMAGE MODE ADJUST

Aspect Ratio Input Signal

037.

INFORMATION REQUEST

037-1. LAMP INFORMATION REQUEST

037-2. LAMP INFORMATION REQUEST 2

037-4. LAMP INFORMATION REQUEST 3

037.6 CARBON SAVINGS INFORMATION REQUEST

037-7. LAMP INFORMATION REQUEST 4

038.

LAMP MODE REQUEST

039.

LAMP MODE SET

046.

WXGA MODE SETTING REQUEST

049.

WXGA MODE SETTING SET

050.

REMOTE KEY CODE

053.

LENS CONTROL

053-1. LENS CONTROL REQUEST

053-2. LENS CONTROL 2

053-3. LENS MEMORY CUSTOM SET

053-4. LENS MEMORY REFERENCE SET

053-5. LENS MEMORY CONTROL REQUEST

053-6. LENS MEMORY CONTROL

053-7. LENS INFORMATION REQUEST

060.

GAIN PARAMETER REQUEST 2

077.

MUTE CONTROL

078-1. SETTING REQUEST

078-2. RUNNING STATUS REQUEST

078-3. INPUT STATUS REQUEST

078-4. MUTE STATUS REQUEST

078-5. MODEL NAME REQUEST

078-6. MIRROR COVER STATUS REQUEST

079.

FREEZE CONTROL

097-198. PIP/SIDE BY SIDE REQUEST

098-193. HDMI AUDIO SELECT SET

098-196. WXGA MODE SETTING SET

098-198. PIP/SIDE BY SIDE SET

110.

AUTO FUNCTIONS EXECUTE

111.

AUTO ADJUST EXECUTE2

305.1. BASE MODEL TYPE REQUEST

305.3 PROJECTOR INFORMATION REQUEST

NEC NP-PX800X2-08ZL, NP-PX750U2-18ZL, NP-PX800X, NP-P501X, NP-P451W User Manual

											Availability by Model (LEGACY MODELS)
Command Name				1		3	4	5	6	7		8	9	10	11	12	13	14	16	17	18	19	20	21	22	23	24	25	26	27	28	29	30	31	32	33	34	35	36	37	38
Command Name				1	2	3	4	5	6	7		8	9	10	11	12	13	14	16	17	18	19	20	21	22	23	24	25	26	27	28	29	30	31	32	33	34	35	36	37	38
006.	RUNNING SENSE			*
006.	RUNNING SENSE			*	*	*	*	*	*	*		*	*	*	*	-	*	*	-	-	*	*	-	-	-	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
007.	COMMON DATA REQUEST			*	*	*	*	*	*	*		*	*	*	*	-	*	*	-	-	*	*	-	-	-	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
009.	ERROR STATUS REQUEST			*	*	*	*	*	*	*		*	*	*	*	*	*	*	-	-	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
015.	POWER ON			*	*	*	*	*	*	*		*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
016.	POWER OFF			*	*	*	*	*	*	*		*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
018.	INPUT SW CHANGE			*	*	*	*	*	*	*		*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
020.	PICTURE MUTE ON			*	*	*	*	*	*	*		*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
021.	PICTURE MUTE OFF			*	*	*	*	*	*	*		*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
022.	SOUND MUTE ON			*	*	*	*	*	*	*		*	*	*	*	*	*	*	*	*	*	*	*	-	*	*	*	*	-	*	*	*	*	*	*	*	-	*	*	*	*
023.	SOUND MUTE OFF			*	*	*	*	*	*	*		*	*	*	*	*	*	*	*	*	*	*	*	-	*	*	*	*	-	*	*	*	*	*	*	*	-	*	*	*	*
024.	ONSCREEN MUTE ON			*	*	*	*	*	*	*		*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
025.	ONSCREEN MUTE OFF			*	*	*	*	*	*	*		*	*	*	*	*	*	*	-	-	*	*	*	*	-	*	*	*	*	-	*	*	*	*	*	*	*	*	*	*	*
030.	GAIN ADJUST			*	*	*	*	*	*	*		*	*	*	*	-	*	*	-	-	*	*	-	-	-	-	-	*	-	-	*	-	*	*	*	*	-	*	*	*	*
030-2. VOLUME ADJUST
	Volume			*	*	*	*	*	*	*		*	*	*	*	-	*	*	-	*	*	*	*	-	*	*	*	*	*	*	-	*	*	*	*	*	*	*	*	*	*
	Bass			-	*	-	-	*	-	*		-	*	-	*	-	-	*	-	-	*	*	-	-	-	-	-	*	-	-	-	-	*	-	*	-	-	*	-	-	-
	Treble			-	*	-	-	*	-	*		-	*	-	*	-	-	*	-	-	*	*	-	-	-	-	-	*	-	-	-	-	*	-	*	-	-	*	-	-	-
	Balance			-	-	-	-	-	-	-		-	-	-	-	-	-	*	-	-	*	*	-	-	-	-	-	*	-	-	-	-	*	-	*	-	-	*	-	-	-
030-12. IMAGE MODE ADJUST
	Aspect Ratio Input Signal			*	*	*	*	*	*	*		*	*	*	*	-	*	*	-	-	*	*	-	-	-	*	*	*	!	*	*	*	*	*	*	*	!	*	*	*	*
037.	INFORMATION REQUEST			*	*	*	*	*	*	*		*	*	*	*	*	*	*	-	-	*	*	*	*	*	!	*	*	!	*	*	*	*	*	*	*	!	*	*	*	*
037-1. LAMP INFORMATION REQUEST				*	*	*	*	*	*	*		*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	-	*	*	*	*	-	*	*	*	*	*	*	*	*	*
037-2. LAMP INFORMATION REQUEST 2				*	*	*	*	*	*	*		*	*	*	*	-	*	*	-	-	*	*	-	-	-	*	-	*	*	*	-	-	*	*	*	*	*	*	*	*	*
037-4. LAMP INFORMATION REQUEST 3				!	!	!	!	!	!	*		*	*	*	*	-	*	*	-	-	*	*	-	*	*	*	*	*	*	*	-	*	*	*	*	*	*	*	*	*	*
037.6. CARBON SAVINGS INFORMATION REQUEST				-	-	-	-	-	-	-		-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	*	*	-	-	-	*
037-7. LAMP INFORMATION REQUEST 4				-	-	-	-	-	-	-		-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	*	*	*	-	-	*
038.	LAMP MODE REQUEST			*	*	*	*	*	*	*		*	*	*	*	-	*	*	-	-	*	*	-	-	-	-	!	*	*	*	*	*	*	*	*	*	*	*	*	*	*
039.	LAMP MODE SET			*	*	*	*	*	*	*		*	*	*	*	-	*	*	-	-	*	*	-	-	-	-	!	*	*	*	*	*	*	*	*	*	*	*	*	*	*
046.	WXGA MODE SETTING REQUEST			-	-	-	-	-	-	-		-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	*	-	-	-	*	*	*	-	*	-	-	*
049.	WXGA MODE SETTING SET			-	-	-	-	-	-	-		-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	*	-	-	-	*	*	*	-	*	-		*
050.	REMOTE KEY CODE			*	*	*	*	*	*	*		*	*	*	*	*	*	*	-	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
053.	LENS CONTROL			-	*	-	-	*	-	*		-	*	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
053-1. LENS CONTROL REQUEST				-	-	-	-	-	-	*		-	*	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
053-2. LENS CONTROL 2				-	-	-	-	-	-	*		-	*	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
053-3. LENS MEMORY CUSTOM SET				-	-	-	-	-	-	*		-	*	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
053-4. LENS MEMORY REFERENCE SET				-	-	-	-	-	-	*		-	*	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
053-5. LENS MEMORY CONTROL REQUEST				-	-	-	-	-	-	*		-	*	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
053-6. LENS MEMORY CONTROL				-	-	-	-	-	-	*		-	*	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
053-7. LENS INFORMATION REQUEST				-	-	-	-	-	-	-		-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
060.	GAIN PARAMETER REQUEST 2			*	*	*	*	*	*	*		*	*	*	*	-	*	*	-	-	*	*	-	-	-	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
077.	MUTE CONTROL			*	*	*	*	*	*	*		*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
078-1. SETTING REQUEST				*	*	*	*	*	*	*		*	*	*	*	-	*	*	-	-	*	*	-	-	-	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
078-2. RUNNING STATUS REQUEST				*	*	*	*	*	*	*		*	*	*	*	-	*	*	-	-	*	*	-	-	-	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
078-3. INPUT STATUS REQUEST				*	*	*	*	*	*	*		*	*	*	*	-	*	*	-	-	*	*	-	-	-	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
078-4. MUTE STATUS REQUEST				*	*	*	*	*	*	*		*	*	*	*	-	*	*	-	-	*	*	-	-	-	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*	*
078-5. MODEL NAME REQUEST				*	*	*	*	*	*	*		*	*	*	*	-	*	*	-	-	*	*	-	-	-	*	*	*	*	*	-	*	*	*	*	*	*	*	*	*	*
078-6. MIRROR COVER STATUS REQUEST				-	-	-	-	-	*	-		-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
079.	FREEZE CONTROL			*	*	*	*	*	*	*		*	*	*	*	-	*	-	-	!	-	-	-	-	*	-	*	-	*	*	-	*	-	*	*	*	*	*	-	*	*
110.	AUTO FUNCTIONS EXECUTE			-	-	-	-	-	-	-		-	-	-	-	-	-	-	-	-	-	-	!	*	-	-	-	-	*	-	-	-	-	*	*	-	*	*	-	-	-
111.	AUTO ADJUST EXECUTE2			-	-	-	-	-	-	-		-	-	-	-	-	-	-	-	-	-	-	-	-	!	-	*	-	-	*	-	-	-	*	*	*	-	*	-	-	*
097-198. PIP/SIDE BY SIDE REQUEST				-	-	-	-	-	-	-		-	-	-	-	-	-	-	-	-	-	!	-	-	-	-	-	*	-	-	-	-	*	*	*	-	-	*	-	-	-
098-196. WXGA MODE SETTING SET				-	-	-	-	-	-	-		-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	*	*	*	-	-	-
098-198. PIP/SIDE BY SIDE SET				-	-	-	-	-	-	-		-	-	-	-	-	-	-	-	-	-	!	-	-	-	-	-	*	-	-	-	-	*	*	*	-	-	*	-	-	-
305.1 BASE MODEL TYPE REQUEST				-	-	-	-	-	-	-		-	-	-	-	*	*	*	-	*	*	*	*	*	*	*	*	*	*	*	-	*	*	*	*	*	*	*	*	*	*
305.3 PROJECTOR INFORMATION REQUEST				-	-	-	-	-	-	-		-	-	-	-	*	*	*	-	*	*	*	*	*	*	*	*	*	*	*	-	*	*	*	*	*	*	*	*	*	*
(!)
LT30		:	firmware version 1.03 or later
NP4000:			firmware version 1.04 or later
NP4001:			firmware version 1.01 or later
NP62		:	firmware version 1.02 or later

======================================================================

5. Command Descriptions

----------------------------------------------------------------------

Precautions with Inscriptions:

(*1) Projector ID

It is the value when forwarding a factory.

This reflects the "Projector ID" that has been set to the projector.

(*2) Model code: "xxH" inscription
This will differ depending on the projector.
In case of MT/NP1000 series	10H
In case of MT/NP3150 series	10H
In case of MT/NP3250 series	10H
In case of PA600 series	10H
In case of PX750 series	10H

In case of PH1000 series	10H
In case of LT/LT80 series	20H
In case of NP61, NP62 series	20H
In case of NP216 series	20H
In case of M402 series	20H
In case of V300 series	20H
In case of VT series	40H
In case of NP600 series	40H
In case of NP610 series	40H
In case of NP2200 series	40H
In case of M300 series	40H
In case of M311 series	40H
In case of P420 series	40H
In case of P501 series	40H
In case of GT series	50H
In case of HT series	60H
In case of WT series	70H
In case of UM330 series	70H
In case of PE401 series	80H
In case of HT10 series	D0H
In case of LT180 series	D0H
In case of LT30 series	D0H
In case of NP60 series	D0H
In case of NP4000, 4100 series	80H
In case of U300 series	80H
In case of NP905/NP901W/VT800	90H

(*3) Checksum: "CKS" inscription

This is the value of the lower 8 bits of the results calculated in byte units from all of the data up to the immediately preceding data.

Example:

20H 81H 01H 60H 01H 00H 03H

+ + + + + + = CKS

(*4) Response error number

This is the value of the error number at the time of an error. See "NAK" of "6-2. Data portion of response".

(*5) Term “RGB” and “COMPUTER”

On the HT1100, VT770, LT245/ LT265/ LT280/ LT380, NP1000/NP2000, NP1150/NP2150/NP3150/NP3151W, NP1250/NP2250/NP3250/NP3250W, NP1200/NP2200, NP4000/NP4001, NP4100/NP4100W, NP905/NP901W/VT800, LT25/LT30/LT35, VT48/VT480/VT580, VT49/VT490/VT590/VT595/VT695/VT700, NP300/NP400/NP500/NP500W/NP500WS/NP600/NP600S, NP310/NP410/MP410W/NP510/NP510W/NP610WS/NP610/NP610S, NP40/NP50/NP60/NP41/NP61/NP62/NP43/NP64, P350X/350W/420X, P401W/P451X/P451W/P501X, PA500X/500U/550W/600X, PX700W/750U/800X and PH1000U the term "RGB connector" has been changed to "COMPUTER".

(*6) Term “DVI” and “COMPUTER”

On the LT380, NP1000/NP2000, NP1150/NP2150/NP3150/NP3151W, NP1250/NP2250/NP3250/NP3250W, NP1200/NP2200, NP4000/NP4001, NP4100/NP4100W, NP300/NP400/NP500/NP500W/NP500WS/NP600/NP600S, NP310/NP410/MP410W/NP510/NP510W/NP610WS/NP610/NP610S and VT595/VT695/VT700, the term "DVI connector" has been changed to "COMPUTER".

006. RUNNING SENSE

**********************************************************************

Function:

This command acquires the operation mode of the projector.

Command:

00H 81H 00H 00H 00H 81H

Response: At the time of a success

20H 81H 01H xxH 01H DATA01 CKS

(*1) (*2) (*3)

Data Portion Contents

-------------------------------------------------------------------

DATA01	Status of operation
	Bit 7: Power On/Off processing
	0	= No execution (Normal condition)
	1	= During execution
	Bit 6: Selecting signal processing
	0	= No execution (Normal condition)
	1	= During execution
	Bit 5: Cooling processing
	0	= No execution (Normal condition)
	1	= During execution
	Bit 4: External control mode
	0	= OFF
	1	= ON

Bit 3: No Power-Off period

0= Power-Off Possible (Normal condition)

1= Power-Off Impossible

Bit 2: Reserved

Bit 1: Projector status 0 = Idling

1 = Power On Bit 0: Reserved

Response: At the time of a failure

A0H 81H 01H xxH 02H DATA1H DATA02 CKS (*1) (*2) (*4) (*3)

007. COMMON DATA REQUEST

**********************************************************************

Function:

This command acquires all of the detailed conditions of the projector.

Command:

00H	C0H	00H	00H 00H C0H
Response: At the time of a success
20H	C0H	01H	xxH 80H DATA01 ..	DATA128 CKS
		(*1)	(*2)	(*3)

Data Portion Contents

-------------------------------------------------------------------

DATA01	Projector type
See DATA70..71
08H	: NP4000 Projector
11H	: NP62 Projector

DATA02

Projector ID

DATA02

1 .. 64 NP4000

1 .. 254 NP62/NP64

1 .. 254 NP216

DATA03	Reserved
DATA04	Projector status

00H: Idling
01H: Power On
DATA05	Cooling processing
00H: No execution (Normal condition)
01H: During execution
DATA06	Indication signal number (Entry list number - 1)
0 .. 199
DATA07	Type 1 of input terminal to be selected (!)
01H	: 1
02H	: 2
03H	: 3
04H	: 4
05H	: 5
DATA08	Type 2 of input terminal to be selected (!1) (!) (!!)
01H	: RGB (*5)
02H	: VIDEO
03H	: S-VIDEO
04H	: COMPONENT
05H	: Reserved
06H	: DIGITAL (*6)
07H	: VIEWER
08H	: SLOT1
09H	: SLOT2
DATA09	Indication signal type

* Valid only when Type 2 of input terminal is 02H or 03H x0H : NTSC3.58

x1H : NTSC4.43 x2H : PAL

x3H : PAL60 x4H : SECAM x5H : B/W60 x6H : B/W50 x7H : PALNM

x8H : NTSC3.58 LBX x9H : NTSC3.58 SQZ xDH : NTSC

xEH : PAL-M xFH : PAL-N * x: undefined

DATA10 .. 12 Reserved ( undefined )

DATA13 .. 20 Horizontal frequency of the indication signal(string) ("000.00" kHz + NULL(0)+ NULL(0) )

DATA21 .. 28 Vertical frequency of the indication signal(string) ("000.00" Hz + NULL(0)+ NULL(0) )

DATA29	Picture mute
00H	: OFF
01H	: ON
DATA30	Sound mute
00H	: OFF
01H	: ON

DATA31 .. Reserved

DATA32 Freeze Status (!2)

00H : OFF

01H : ON

FFH : Not Supported

DATA33

Test pattern display 1

00H : No display (Normal condition)

00H Other : Displaying (Pattern ID)

Pattern ID

Pattern Name

LT180

LT80

NP1000

NP3150

NP905

NP4000

NP4100

NP62

NP64

NP3250

NP216

P420

V300

VE281

P501

M402

02H

Cross Hatch

03H

Gray Bars

04H

Raster(0%)

05H

Raster(25%)

06H

Raster(50%)

07H

Raster(100%)

08H

Focus

09H

Raster Blue

0AH

Gray Raster 30

17H

Gray Raster 10

18H

RAMP WBRG

19H

Blue Raster 60

1DH

Cross Hatch 3

Supported

* :

- :

Not supported

*1: Only LT240K/260K

Pattern ID

Pattern Name

PA600

PX750

PH1000

01H

Cross Hatch

02H

Gray Bars

03H

Raster(0%)

04H

Raster(25%)

05H

Raster(50%)

06H

Raster(100%)

07H

Color Bar

DATA34

Test pattern display 2

FFH: No display (Normal condition) FFH Other: Displaying

Bit 2: BLUE pattern 0 = OFF

1 = ON

Bit 1: GREEN pattern 0 = OFF

1 = ON

Bit 0: RED pattern 0 = OFF

1 = ON

DATA35 .. 50 Reserved

DATA51 .. 65 User registration name ( 14 characters + NULL )

DATA66

Forced On-screen mute

00H	: OFF
01H	: ON
DATA67	On-screen display
00H	: No display
01H	: Displaying
DATA68	Selecting signal processing
00H	: No execution (Normal condition)
01H	: During execution
DATA69	Status of operation
00H	: Idling
04H	: Power On
05H	: Cooling
06H	: Idling (Error occurrence)
Other than above: (nondisclosure)
Internal use of code during a state transition period
DATA70 .. 71	Projector type

Data01	Data70	Data71
01H	00H	03H	MT1060/MT1065
01H	01H	03H	MT860
01H	02H	03H	MT1075
01H	00H	06H	NP1000/NP2000
02H	00H	03H	LT240/LT260
02H	01H	03H	LT220
02H	02H	03H	LT240K/LT260K
02H	00H	05H	LT245/LT265
02H	00H	06H	LT380
02H	01H	06H	LT280
03H	00H	04H	VT770
03H	00H	06H	VT80 Series
03H	00H	07H	VT90 Series
04H	00H	01H	GT1150
04H	01H	01H	GT2150
04H	00H	03H	GT5000
04H	01H	03H	GT6000
05H	00H	03H	HT1000
05H	00H	04H	HT1100
06H	00H	03H	WT600
06H	00H	05H	WT610/WT615
08H	00H	07H	NP4000/NP4001
08H	00H	10H	NP4100
08H	01H	10H	NP4100W
10H	00H	08H	VT700
10H	00H	09H	NP600
10H	01H	09H	NP500
10H	02H	09H	NP500 W
10H	03H	09H	NP400
10H	04H	09H	NP300
10H	00H	10H	NP610
10H	01H	10H	NP510
10H	02H	10H	NP510W
10H	03H	10H	NP410
10H	05H	10H	NP310
10H	07H	10H	NP610S
10H	08H	10H	NP510WS
10H	09H	10H	NP410
10H	01H	11H	NP2200
10H	02H	11H	NP1200
11H	00H	00H	NP41/61
11H	01H	00H	NP62
11H	00H	11H	NP215
11H	02H	11H	NP115
11H	03H	11H	NP110
11H	04H	11H	NP216
11H	00H	12H	NP64
11H	03H	12H	NP43
12H	00H	08H	NP1150/NP2150/NP3150
12H	01H	08H	NP3151W
12H	00H	09H	NP905
12H	01H	09H	NP901W
12H	02H	09H	VT800
12H	00H	10H	NP1250/NP2250/NP3250
12H	01H	10H	NP3250W
13H	01H	10H	M300X
13H	02H	10H	M300W
13H	05H	10H	M260X
13H	06H	10H	M260W
13H	00H	11H	P420X
13H	01H	11H	P350X
13H	02H	11H	P350W
13H	00H	12H	UM330X
13H	01H	12H	UM330W
13H	00H	13H	M361X
13H	01H	13H	M311W
13H	02H	13H	M271X
13H	03H	13H	M311X
14H	00H	11H	PE401H
14H	02H	10H	U300X
14H	04H	10H	U310W
15H	00H	10H	PA600X
15H	01H	10H	PA500X
15H	02H	10H	PA550W
15H	03H	10H	PA500U
16H	00H	10H	V300X
16H	01H	10H	V260X
16H	03H	10H	V260
16H	01H	11H	VE281X/VE281XB
16H	04H	11H	VE281/VE281B
17H	00H	10H	PX750U
17H	01H	10H	PX700W
17H	02H	10H	PX800X
19H	00H	10H	PH1000U
20H	00H	10H	P501X
20H	01H	10H	P451X
20H	02H	10H	P451W
20H	03H	10H	P401W
22H	00H	10H	M401X
22H	02H	10H	M322X
22H	03H	10H	M282X
22H	06H	10H	M322W
22H	07H	10H	M332XS
22H	09H	10H	M352WS

+ 44 hidden pages