Size:
6.44 Mb
Download

FV (Firmware Versions)

Execution:

This command can be executed in the AC POWER ON or DC POWER ON state.

Function:

Displays the version information of the iSPFW and BIOS.

Performs a checksum of the storage area.

Note: The FV command can be executed in Normal mode or

Maintenance mode.

Table 3-32.FV Screen

Screen Image

 

 

Reference

iSPyz:--->fv<ENTER>

 

 

Firmware Versions

: (currently running firmware is Rxx.xx)

 

iSP BOOT

(*)

: xx.xx generated on mm/dd/yyyy hh:mm:ss

A

iSP FW bank0

 

: xx.xx generated on mm/dd/yyyy hh:mm:ss

iSP FW bank1

(*)

: xx.xx generated on mm/dd/yyyy hh:mm:ss

 

BIOS bank

(*)

: xx.xx generated on mm/dd/yyyy hh:mm:ss

 

Do you want to check the flash memory? (y/[n]) : y<ENTER>

B

checking iSP BOOT bank...

 

 

passed.

 

 

 

checking iSP FW bank0...

 

 

passed.

 

 

C

checking iSP FW bank1...

 

passed.

 

 

 

checking BIOS bank...

 

 

passed.

 

 

 

FV command terminated.

 

 

 

 

 

 

 

Table 3-33FV Screen References

 

 

Reference

Description

A

Displays the state of the current FW storage area.

B

To perform a checksum test of the storage area, enter “y”.

C

Displays the state of the checksum test.

 

 

Service Processor 3-31

HC (Hardware Configuration)

Execution:

Conditions for executing subcommands are described in the following subcommand table.

Function:

Displays and changes the configuration information of the hardware. Displays and changes the partition settings.

See Table 3-38,“HC – ALL Display Screen” for an example of the HC display screen.

See the following tables for a list of hardware components and subcomponents and for a list of subcommands and descriptions.

Note: The HC command can be executed in Normal mode or

Maintenance mode.

Table 3-34.HW Components and Subcomponents

Component

Subcomponent (1)

Subcomponent (2)

CELLV Board

Processor x4

--

 

MMC x2

ROW x8

 

 

CACHE x8

 

TAG x8

--

 

CXI x2

--

 

 

 

XIC Board

CXI x4

--

 

1.6G x4

--

 

MOVER x2

--

 

SERIAL CONSOLE x4

--

 

 

 

PCIV/PCIX Unit

IOR

1.6G x2

 

 

IOC x2

 

GXB x4 or GXB x2

--

 

 

 

3-32Service Processor

Table 3-35.HC Subcommands

cmd

arg1

arg2

arg3

arg4

Description

help

-

-

-

-

Displays the list of subcommands.

 

 

 

 

 

This command can be executed in the AC

 

 

 

 

 

POWER ON or DC POWER ON state.

 

 

 

 

 

 

quit

-

-

-

-

Exits from the HC command.

exit

 

 

 

 

Before an exit, the check subcommand is

 

 

 

 

 

 

 

 

 

 

automatically executed.

 

 

 

 

 

This command can be executed in the AC

 

 

 

 

 

POWER ON state or DC POWER ON state.

 

 

 

 

 

 

disp

-

-

-

-

Used to display states.

 

 

 

 

 

Displays Help for “disp” when the argument is

 

 

 

 

 

omitted or an error exists.

 

 

 

 

 

This command can be executed in the AC

 

 

 

 

 

POWER ON or DC POWER ON state.

 

 

 

 

 

 

 

all

-

-

-

Displays all the states.

 

 

 

 

 

 

 

part

-

-

-

Displays the following partition division

 

 

 

 

 

information for each partition:

 

 

 

 

 

State summary

 

 

 

 

 

Physical CELLV Board number and logical

 

 

 

 

 

CELLV Board number

 

 

 

 

 

Physical IOR chip number and logical IOR chip

 

 

 

 

 

number.

 

main

-

-

-

Displays the state summary of the system

 

 

 

 

 

configuration.

 

 

 

 

 

 

 

cellx

-

-

-

Displays the state of the CELLV Board.

 

 

 

 

 

x” is the physical CELLV Board number(0-3).

 

 

 

 

 

 

 

mmcxy

-

-

-

Displays the detailed state of the ROW under

 

 

 

 

 

control of the MMC specified by “xy”.

 

 

 

 

 

x” is the physical CELLV Board number(0-3)on

 

 

 

 

 

which MMC is installed.

 

 

 

 

 

y” is the MMC number(0-1)in the CELLV

 

 

 

 

 

Board.

 

 

 

 

 

 

 

tagx

-

-

-

Displays the detailed state of the TAG.

 

 

 

 

 

x” is the physical CELLV Board number(0-3)on

 

 

 

 

 

which TAG is installed.

 

 

 

 

 

 

 

xbcx

-

-

-

Displays the state of the XBC chip.

 

 

 

 

 

x” is the physical XBC chip number(0-1).

 

 

 

 

 

 

Service Processor 3-33

Table 3-35.HC Subcommands (cont’d)

cmd

arg1

arg2

arg3

arg4

Description

disp

pcixx

-

-

-

Displays the state of the PCIV/PCIX Unit.

(cont’d)

 

 

 

 

x” is the DGI/I2C cable port number(0-3)from

 

 

 

 

 

 

 

 

 

 

the iSP-CBoard to the PCIV/PCIX Unit.

 

 

 

 

 

IOR0 is installed on the XIC Board. But the

 

 

 

 

 

IOR0 is displayed with the PCIX0(V) to realize

 

 

 

 

 

the same operation as the PCIX Unit.

 

 

 

 

 

 

 

pbayxy

-

-

-

Displays the state of the Power Bay/Power Bay

 

 

 

 

 

Unit.

 

 

 

 

 

x” is the chassis number.

 

 

 

 

 

0: Power Bay in the Main/Expansion Chassis

 

 

 

 

 

1: Power Bay Unit

 

 

 

 

 

y” is the ID number.

 

 

 

 

 

0 for the Power Bay in the Main Chassis

 

 

 

 

 

1 for the Power Bay in the Expansion Chassis

 

 

 

 

 

0 for the Power Bay Unit

 

 

 

 

 

 

attach

-

-

-

-

Used to associate partition numbers to CELLV

 

 

 

 

 

Boards and IORs.

 

 

 

 

 

The number of CELLV Boards in a partition

 

 

 

 

 

must be the same or greater than the number of

 

 

 

 

 

IORs.

 

 

 

 

 

Displays Help for “attach” when the argument is

 

 

 

 

 

omitted or an error is made.

 

 

 

 

 

This subcommand can be executed in the DC

 

 

 

 

 

POWER OFF state of the partition.

 

 

 

 

 

When the online configuration and

 

 

 

 

 

deconfiguration function is released, this

 

 

 

 

 

restriction will be relieved.

 

 

 

 

 

 

 

cellx

n

m

-

Associates the CELLV Board having the

 

 

 

 

 

physical number x with the logical CELLV Board

 

 

 

 

 

number m of partitionn. (m: The number

 

 

 

 

 

recognizable by the BIOS and software.)

 

 

 

 

 

This command can also be used to change a

 

 

 

 

 

logical CELLV Board number if it has already

 

 

 

 

 

been associated.

 

 

 

 

 

Each logical CELLV Board number must be

 

 

 

 

 

unique among the CELLV Boards.

 

 

 

 

 

You cannot change the logical number of the

 

 

 

 

 

CELLV Board in the online state.

 

 

 

 

 

 

3-34Service Processor

Table 3-35.HC Subcommands (cont’d)

cmd

arg1

arg2

arg3

arg4

Description

attach

iorx

n

m

p

Associates the IOR having the physical number

(cont’d)

 

 

 

 

x with the logical IOR numberm of partitionn.

 

 

 

 

 

(m: The number recognizable by the BIOS and

 

 

 

 

 

software.)

 

 

 

 

 

p(0-9)sets the priority.

 

 

 

 

 

Indicates which IOR is used with a higher

 

 

 

 

 

priority if the number of normal CELLV Boards is

 

 

 

 

 

smaller than the number of normal IORs due to

 

 

 

 

 

CELLV Board failure in the partition. (Smaller

 

 

 

 

 

values have a higher priority, and the IORs with

 

 

 

 

 

larger values get isolated one by one. If the

 

 

 

 

 

priority number is the same, the one with a

 

 

 

 

 

smaller physical IOR number has a higher

 

 

 

 

 

priority.)

 

 

 

 

 

This command can be used to change the

 

 

 

 

 

logical IOR number and priority if it has been

 

 

 

 

 

already associated.

 

 

 

 

 

The logical IOR number must be unique within

 

 

 

 

 

the partition.

 

 

 

 

 

You cannot change the logical IOR number or

 

 

 

 

 

priority of the IOR which is in the online state.

 

 

 

 

 

"Priority 0" is allowed one time for one partition

 

 

 

 

 

and a Basic I/O Board must be connected. If

 

 

 

 

 

any failure occurs in this IOR, the partition

 

 

 

 

 

cannot be started.

 

 

 

 

 

The IOR0 must have priority 0.

 

 

 

 

 

 

detach

-

-

-

-

Used to cancel the associations between

 

 

 

 

 

partition numbers and CELLV Boards/IORs.

 

 

 

 

 

You cannot detach any component that is in the

 

 

 

 

 

online state.

 

 

 

 

 

The number of CELLV Boards in a partition

 

 

 

 

 

must be greater than or equal to the number of

 

 

 

 

 

IORs.

 

 

 

 

 

Displays Help of “detach” when the argument is

 

 

 

 

 

omitted or an error is made.

 

 

 

 

 

 

 

cellx

-

-

-

Disassociates the CELLV Board having the

 

 

 

 

 

physical number x from the currently associated

 

 

 

 

 

partition.

 

 

 

 

 

 

 

iorx

-

-

-

Disassociates the IOR having the physical

 

 

 

 

 

number x from the currently associated partition.

 

 

 

 

 

 

Service Processor 3-35

Table 3-35.HC Subcommands (cont’d)

 

cmd

arg1

arg2

arg3

arg4

Description

 

swap

-

-

-

-

 

Used to swap a CELLV Board with another

 

 

 

 

 

 

 

 

CELLV Board while the software is operating.

 

 

This subcommand is not supported at

 

 

 

 

 

 

(This is not a combination of “attach” and

 

 

present.

 

 

 

 

 

 

 

 

 

 

 

 

“detach”. The process dedicated for “swap” is

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

executed.)

 

 

 

 

 

 

 

 

Displays Help for “swap” when the argument is

 

 

 

 

 

 

 

 

omitted or an error is made.

 

 

 

 

 

 

 

 

This subcommand can be executed on the

 

 

 

 

 

 

 

 

partition in the DC POWER ON state. An

 

 

 

 

 

 

 

 

execution of “swap” on the partitions requires

 

 

 

 

 

 

 

 

the online configuration and de-configuration

 

 

 

 

 

 

 

 

function of the OS.

 

 

 

 

 

 

 

 

 

 

 

 

cellx

celly

-

-

 

Swaps the operating CELLV Board having the

 

 

 

 

 

 

 

 

physical number x with the CELLV Board having

 

 

 

 

 

 

 

 

the physical number y.

 

 

 

 

 

 

 

 

No partition must be associated with CELLVy.

 

 

 

 

 

 

 

 

When the swap is complete, CELLVx is

 

 

 

 

 

 

 

 

disassociated from the partition and CELLVy is

 

 

 

 

 

 

 

 

associated to the partition.

 

 

 

 

 

 

 

 

The logical CELL Board number is transferred

 

 

 

 

 

 

 

 

from CELLVx to CELLVy.

 

 

 

 

 

 

 

 

 

 

smem

-

-

-

-

 

Used to specify the size of the shared memory

 

 

 

 

 

 

 

 

of the partition.

 

 

This subcommand is not supported at

 

 

 

 

 

 

 

 

 

present.

 

 

 

 

 

Displays Help for “smem” when the argument is

 

 

 

 

 

 

 

 

omitted or an error is made.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This subcommand can be executed on the

 

 

 

 

 

 

 

 

partition in the DC POWER OFF state.

 

 

 

 

 

 

 

 

 

 

 

 

n

mmm

-

-

 

Specifies the size of the shared memory of

 

 

 

 

 

 

 

 

partition n in units of MB.

 

 

 

 

 

 

 

 

You cannot make any change to the partitions

 

 

 

 

 

 

 

 

currently in operation.

 

 

 

 

 

 

 

 

If the size is not a multiple of 128 MB, it is

 

 

 

 

 

 

 

 

rounded up.

 

 

 

 

 

 

 

 

 

3-36Service Processor

Table 3-35.HC Subcommands (cont’d)

cmd

arg1

arg2

arg3

arg4

Description

add

-

-

-

-

Used to instruct the iSP to add components

 

 

 

 

 

manually. The management state of the iSP

 

 

 

 

 

changes from “nonexist” to “power-off”.

 

 

 

 

 

Displays Help for “add” when the argument is

 

 

 

 

 

omitted or an error is made.

 

 

 

 

 

This subcommand can be executed in the AC

 

 

 

 

 

POWER ON state or DC POWER ON state.

 

 

 

 

 

When the Power Bay Unit is added, all partitions

 

 

 

 

 

must be in the DC POWER OFF state.

 

 

 

 

 

 

 

pbayxy

-

-

-

Adds a Power Bay/Power Bay Unit.

 

 

 

 

 

x” is the chassis number.

 

 

 

 

 

0: Power Bay in the Main/Expansion Chassis

 

 

 

 

 

1: Power Bay Unit

 

 

 

 

 

y” is the ID number.

 

 

 

 

 

0 for the Power Bay in the Main Chassis

 

 

 

 

 

1 for the Power Bay in the Expansion Chassis

 

 

 

 

 

0 for the Power Bay Unit

 

 

 

 

 

 

 

dpsxyz

-

-

-

Adds DPS to the Power Bay/Power Bay Unit.

 

 

 

 

 

x” and “y” are the same as described in “pbay”

 

 

 

 

 

above.

 

 

 

 

 

z” is the number of Distributed Power Supply

 

 

 

 

 

Module (DPS) in the Power Bay Unit (0-5).But

 

 

 

 

 

the number assigned in the Power Bay of the

 

 

 

 

 

Main Chassis and Expansion Chassis is 0,1 or

 

 

 

 

 

2.

 

 

 

 

 

 

 

xbcx

-

-

-

Adds a XBC chip.

 

 

 

 

 

x” is the physical number of the XBC chip(0-1).

 

 

 

 

 

0: Used for the XBC chip on the XIC Board.

 

 

 

 

 

1: Used for the XBC chip on the XBR Board.

 

 

 

 

 

 

 

cellx

-

-

-

Adds a CELLV Board.

 

 

 

 

 

x” is the physical number of the CELLV Board

 

 

 

 

 

(0-3).

 

 

 

 

 

0 or 3 is assigned to the CELLV Board in the

 

 

 

 

 

Main Chassis.

 

 

 

 

 

 

 

procxy

-

-

-

Adds a processor.

 

 

 

 

 

x” is the physical CELLV Board number(0-3).

 

 

 

 

 

y” is the processor installation location on the

 

 

 

 

 

CELLV Board (0-3).

 

 

 

 

 

 

Service Processor 3-37

Table 3-35.HC Subcommands (cont’d)

cmd

arg1

arg2

arg3

arg4

Description

add

pcixx

[bio]

 

 

Adds a PCIV/PCIX Unit.

(cont’d)

 

 

 

 

x” is the DGI/I2C port number of theiSP-C

 

 

 

 

 

 

 

 

 

 

Board side (0-3).

 

 

 

 

 

If PCIV is specified, “0” must be specified to x.

 

 

 

 

 

If a PCiX Unit is specified, 1,2 or 3 must be

 

 

 

 

 

specified to x.

 

 

 

 

 

If the Basic I/O Board is attached, specify “bio”

 

 

 

 

 

as the second argument.

 

 

 

 

 

“bio” must be specified in the case of the

 

 

 

 

 

PCIX0(V).

 

 

 

 

 

IOR0 is installed on the XIC Board. But the

 

 

 

 

 

IOR0 is added when the PCIX0(V) is added to

 

 

 

 

 

realize the same operation as the PCIX Unit.

 

 

 

 

 

 

delete

-

-

-

-

Used to delete a component from the iSP

 

 

 

 

 

management. If you do not delete it from the

 

 

 

 

 

iSP management, the component which has

 

 

 

 

 

been physically removed will still be managed

 

 

 

 

 

as “INVISIBLE”.

 

 

 

 

 

You cannot delete any components in the DC

 

 

 

 

 

ON state (except Distributed Power Supply

 

 

 

 

 

Module (DPS)).

 

 

 

 

 

Displays Help for “delete” when the argument is

 

 

 

 

 

omitted or an error is made.

 

 

 

 

 

 

 

<arg1>

-

-

-

<arg1> is the same as described in “add”.

 

 

 

 

 

 

enable

-

-

-

-

Used to enable a component managed as

 

 

 

 

 

”DISABLE”.

 

 

 

 

 

Displays Help for ”enable” when the argument is

 

 

 

 

 

omitted or an error is made.

 

 

 

 

 

This subcommand can be executed in the DC

 

 

 

 

 

POWER OFF state of the partition that will use

 

 

 

 

 

the component.

 

 

 

 

 

When the online configuration and

 

 

 

 

 

deconfiguration function is released, this

 

 

 

 

 

restriction will be relieved.

 

 

 

 

 

 

 

pbayxy

-

-

-

Enables a Power Bay/Power Bay Unit.

 

 

 

 

 

x” is the chassis number.

 

 

 

 

 

0: Power Bay in the Main/Expansion Chassis

 

 

 

 

 

1: Power Bay Unit

 

 

 

 

 

y” is the ID number.

 

 

 

 

 

0 for the Power Bay in the Main Chassis

 

 

 

 

 

1 for the Power Bay in the Expansion Chassis

 

 

 

 

 

0 for the Power Bay Unit

 

 

 

 

 

 

3-38Service Processor

Table 3-35.HC Subcommands (cont’d)

cmd

arg1

arg2

arg3

arg4

Description

enable

xbcx

[all]

-

-

Enables the XBC chip.

(cont’d)

 

 

 

 

x” is the XBC chip number(0-1).

 

 

 

 

 

 

 

 

 

 

When the second argument is omitted, only the

 

 

 

 

 

XBC is enabled, and the states of any other

 

 

 

 

 

subcomponents do not change.

 

 

 

 

 

When “all” is specified as the second argument,

 

 

 

 

 

not only the XBC but also its subcomponents

 

 

 

 

 

become enabled.

 

 

 

 

 

 

 

 

cxix

-

-

Enables the CELLV Board interface part within

 

 

 

 

 

the XBC chip.

 

 

 

 

 

x” is the interface part number(0-3).

 

 

 

 

 

The correspondence between CXI number of

 

 

 

 

 

the CELLV Board and the CXI number of the

 

 

 

 

 

XBC chip depends on the type of System Back

 

 

 

 

 

Plane.

 

 

 

 

 

System Back Plane (8-way):

 

 

 

 

 

CELL0 CXI0 - CXI0 XBC0

 

 

 

 

 

CELL0 CXI1 - CXI1 XBC0

 

 

 

 

 

CELL3 CXI0 - CXI2 XBC0

 

 

 

 

 

CELL3 CXI1 - CXI3 XBC0

 

 

 

 

 

When the CXI port within the XBC chip is

 

 

 

 

 

enabled, corresponding CXI port in the CELLV

 

 

 

 

 

Board is also enabled (and vice versa).

 

 

 

 

 

In the case of the System Back Plane (8-way),

 

 

 

 

 

refer to below.

 

 

 

 

 

When port 0 is enabled, port 1 is also enabled.

 

 

 

 

 

When port 1 is enabled, port 0 is also enabled.

 

 

 

 

 

When port 2 is enabled, port 3 is also enabled.

 

 

 

 

 

When port 3 is enabled, port 2 is also enabled.

 

 

 

 

 

 

 

 

ncix

-

-

Enables the NC interface part within the XBC

 

 

 

 

 

chip.

 

 

 

 

 

x” is the interface number(0-1).

 

 

 

 

 

0: 1.6G cable port 0

 

 

 

 

 

1: 1.6G cable port 1

 

 

 

 

 

When the 1.6G port of XBC chip is enabled,

 

 

 

 

 

corresponding port in the NC chip/IOR chip is

 

 

 

 

 

also enabled (and vice versa).

 

 

 

 

 

 

 

 

moverx

-

-

Enables the MOVER part within the XBC chip.

 

 

 

 

 

x” is the mover number(0-1).

 

 

 

 

 

 

Service Processor 3-39

Table 3-35.HC Subcommands (cont’d)

cmd

arg1

arg2

arg3

arg4

Description

enable

 

serialx

-

-

Enables the serial controller part within the XBC

(cont’d)

 

 

 

 

chip.

 

 

 

 

 

x” is the serial controller number(0-3).

 

 

 

 

 

A partition requires a serial controller. When a

 

 

 

 

 

partition contains plural CELLV Boards, a serial

 

 

 

 

 

controller is selected from available serial

 

 

 

 

 

controllers automatically.

 

 

 

 

 

 

 

cellx

[all]

-

-

Enables the CELLV Board.

 

 

 

 

 

x” is the physical CELLV Board number(0-3).

 

 

 

 

 

When the second argument is omitted, only the

 

 

 

 

 

CELLV Board is enabled, and the states of any

 

 

 

 

 

other subcomponents do not change. In this

 

 

 

 

 

case, operation is rejected if some required

 

 

 

 

 

components are disabled.

 

 

 

 

 

When “all” is specified as the second argument,

 

 

 

 

 

not only the CELLV Board but also its

 

 

 

 

 

subcomponents become enabled.

 

 

 

 

 

 

 

 

cxiy

-

-

Enables the XBC interface part within the

 

 

 

 

 

CELLV Board.

 

 

 

 

 

y” is the interface part number(0-1).

 

 

 

 

 

For information on the relationship between the

 

 

 

 

 

CXI within the CELLV Board and the CXI within

 

 

 

 

 

the XBC chip, refer to “cxix” of “xbcx” in

 

 

 

 

 

“enable”.

 

 

 

 

 

 

 

procxy

-

-

-

Enables the Processor.

 

 

 

 

 

x” is the physical CELLV Board number(0-3).

 

 

 

 

 

y” is the Processor number(0-3)within the

 

 

 

 

 

CELLV Board .

 

 

 

 

 

 

 

mmcxy

[all]

-

-

Enables the MMC.

 

 

 

 

 

x” is the physical CELLV Board number(0-3).

 

 

 

 

 

y” is the MMC number(0-1)within the CELLV

 

 

 

 

 

Board.

 

 

 

 

 

When the second argument is omitted, only the

 

 

 

 

 

MMC is enabled, and the states of any other

 

 

 

 

 

subcomponents do not change.

 

 

 

 

 

When “all” is specified as the second argument,

 

 

 

 

 

not only the MMC but also its subcomponents

 

 

 

 

 

become enabled.

 

 

 

 

 

 

 

 

rowz

-

-

Enables the ROW.

 

 

 

 

 

z” is the ROW number(0-3).

 

 

 

 

 

DIMM is not controlled individually.

 

 

 

 

 

DIMMs are automatically detected at the time of

 

 

 

 

 

startup.

 

 

 

 

 

 

3-40Service Processor

Table 3-35.HC Subcommands (cont’d)

cmd

arg1

arg2

arg3

arg4

Description

 

 

 

 

 

 

enable

mmcxy

cachez

-

-

Enables the Cache.

(cont’d)

(cont’d)

 

 

 

z” is the Cache number(0-7).

 

 

 

 

 

 

 

 

 

 

 

 

tagx[sy]

-

-

-

Enables the TAG.

 

 

 

 

 

x” is the physical CELLV Board number(0-3).

 

 

 

 

 

s” is either “e” (EVEN side) or “o” (ODD side).

 

 

 

 

 

y” is the TAG number(0-3).

 

 

 

 

 

When “sy” is omitted, all the TAGs under the

 

 

 

 

 

CELLV Board specified by “x” become enabled.

 

 

 

 

 

 

 

pcixx

all

-

-

Enables the PCIV/PCIX Unit.

 

 

 

 

 

x” is the DGI/I2C cable port number(0-3)of the

 

 

 

 

 

cable from the ISP-CBoard to the PCIV/PCIX

 

 

 

 

 

Unit.

 

 

 

 

 

“all” must be specified as the second argument.

 

 

 

 

 

Then, not only the PCIV /PCIX Unit but also its

 

 

 

 

 

subcomponents become enabled.

 

 

 

 

 

IOR0 is installed on the XIC Board. But the

 

 

 

 

 

IOR0 is managed with the PCIX0(V) to realize

 

 

 

 

 

the same operation as the PCIX Unit.

 

 

 

 

 

 

 

iorx

[all]

-

-

Enables the IOR chip.

 

 

 

 

 

x” is the physical IOR chip number(0-3).

 

 

 

 

 

When the second argument is omitted, only the

 

 

 

 

 

IOR chip is enabled, and the states of any other

 

 

 

 

 

subcomponents do not change.

 

 

 

 

 

When “all” is specified as the second argument,

 

 

 

 

 

not only the IOR chip but also its

 

 

 

 

 

subcomponents become enabled.

 

 

 

 

 

 

 

 

nciy

-

-

Enables the 1.6G interface part.

 

 

 

 

 

y” is the interface number (0 only).

 

 

 

 

 

When the 1.6G port of IOR chip is enabled,

 

 

 

 

 

corresponding 1.6G port in the XBC chip/NC

 

 

 

 

 

chip is also enabled (and vice versa).

 

 

 

 

 

 

 

 

iocy

-

-

Enables the IOC.

 

 

 

 

 

y” is the IOC number (0 or 1) within the IOR

 

 

 

 

 

Daughter Board.

 

 

 

 

 

 

Service Processor 3-41

Table 3-35.HC Subcommands (cont’d)

cmd

arg1

arg2

arg3

arg4

Description

enable

gxbxy

-

-

-

Enables the GXB.

(cont’d)

 

 

 

 

x” is the DGI/I2C cable port number of the

 

 

 

 

 

 

 

 

 

 

cable from the iSP-CBoard to the PCIV /PCIX

 

 

 

 

 

Unit (0-3).

 

 

 

 

 

y” is the GXB number(0-3)within the

 

 

 

 

 

PCIV/PCIX Unit. PCIV does not have GXB

 

 

 

 

 

number (1).

 

 

 

 

 

 

 

 

busA

-

-

Enables the busA side and busB side of GXB.

 

 

|busB

 

 

 

 

 

 

 

 

 

disable

-

-

-

-

Used to disable a component manually.

 

 

 

 

 

Displays Help for “disable” when the argument

 

 

 

 

 

is omitted or an error is made.

 

 

 

 

 

If the component is online state, the component

 

 

 

 

 

can not be disabled.

 

 

 

 

 

 

 

<arg1>

<arg2>

-

-

<arg1> and<arg2> are the same as described

 

 

 

 

 

in “enable” above.

 

 

 

 

 

“all” cannot be specified.

 

 

 

 

 

 

online

-

-

-

-

Used to dynamically configure an offline

 

 

 

 

 

component while the OS is running.

 

 

 

 

 

This command functions only with the support of

 

 

 

 

 

the software (OS and BIOS).

 

 

 

 

 

This SP command may be unnecessary

 

 

 

 

 

depending on the OS.

 

 

 

 

 

Displays Help for “online” when the argument is

 

 

 

 

 

omitted or an error is made.

 

 

 

 

 

 

 

cellx

-

-

-

Configures the CELLV Board for the OS.

 

 

 

 

 

 

 

xbcx

moverx

-

-

Configures the XBC chip’s mover for the OS.

 

 

 

 

 

 

 

iorx

-

-

-

Configures the IOR chip for the OS.

 

 

 

 

 

 

offline

-

-

-

-

Used to dynamically disconfigure an online

 

 

 

 

 

component while the OS is running.

 

 

 

 

 

This command functions only with the support of

 

 

 

 

 

the software (OS and BIOS).

 

 

 

 

 

This SP command may be unnecessary

 

 

 

 

 

depending on the OS.

 

 

 

 

 

Display Help for “offline” when the argument is

 

 

 

 

 

omitted or an error is made.

 

 

 

 

 

 

 

<arg1>

<arg2>

-

-

Same as described in “online” above.

 

 

 

 

 

 

3-42Service Processor

Table 3-35.HC Subcommands (cont’d)

cmd

arg1

arg2

arg3

arg4

Description

ncconn

-

-

-

-

Used to set connection information of the 1.6G

 

 

 

 

 

cable.

 

 

 

 

 

Displays Help for “ncconn” when the argument

 

 

 

 

 

is omitted or an error is made.

 

 

 

 

 

This subcommand can be executed when all

 

 

 

 

 

partitions are in the DC POWER OFF state.

 

 

 

 

 

 

 

xbcx

nciy

iors

ncit

Specifies the connection between the 1.6G port

 

 

 

 

 

with the port number y in the XBC chip with the

 

iors

ncit

xbcx

nciy

physical number x and the 1.6G port with the

 

 

 

 

 

port number t in the IOR chip with the physical

 

 

 

 

 

number s.

 

 

 

 

 

t must be (0).

 

 

 

 

 

 

ncdis

-

-

-

-

Used to disconnect the 1.6G cable.

 

 

 

 

 

Displays Help for “ncdis” when the argument is

 

 

 

 

 

omitted or an error is made.

 

 

 

 

 

This subcommand can be executed when all

 

 

 

 

 

partitions are in the DC POWER OFF state.

 

 

 

 

 

 

 

xbcx

nciy

-

-

Removes the connection of the 1.6G port with

 

 

 

 

 

the port number y in the XBC chip with the

 

 

 

 

 

physical number x.

 

 

 

 

 

It is linked to the disconnection of the

 

 

 

 

 

corresponding port (and vice versa).

 

 

 

 

 

 

 

iors

ncit

-

-

Removes the connection of the 1.6G port with

 

 

 

 

 

the port number t in the IOR chip with the

 

 

 

 

 

physical number s.t must be (0).

 

 

 

 

 

It is linked to the disconnection of the

 

 

 

 

 

corresponding port (and vice versa).

 

 

 

 

 

 

led

-

-

-

-

Used to turn on/off a component’s LED to

 

 

 

 

 

identify its location.

 

 

 

 

 

Displays Help for “led” when the argument is

 

 

 

 

 

omitted or an error is made.

 

 

 

 

 

For execution on XBC (XIC Board/XBR Board)

 

 

 

 

 

and CELLV Board, one of the partitions must be

 

 

 

 

 

in the DC POWER ON state.

 

 

 

 

 

For execution on the PCIX, no condition is

 

 

 

 

 

required.

 

 

 

 

 

For execution on the PCI slot, the superior GXB

 

 

 

 

 

must be in the online state.

 

 

 

 

 

 

 

xbcx

on|off

-

-

Turns on/off the LED of the XIC Board/XBR

 

 

 

 

 

Board.

 

 

 

 

 

x” is specified as below.

 

 

 

 

 

0: XIC Board

 

 

 

 

 

1: XBR Board

 

 

 

 

 

 

Service Processor 3-43

Table 3-35.HC Subcommands (cont’d)

cmd

arg1

arg2

arg3

arg4

Description

led

cellx

on|off

-

-

Turns on/off the LED of the CELLV Board.

(cont’d)

 

 

 

 

x” is the physical CELLV Board number(0-3).

 

 

 

 

 

 

 

 

 

 

 

 

pcixx

on|off

-

-

Turns on/off the LED of the PCIV/PCIX Unit.

 

 

 

 

 

x” is the number of PCIV/PCIX Unit

 

 

 

 

 

(0-3).

 

 

 

 

 

When the PCIV is specified, all alarm LEDs are

 

 

 

 

 

turned on.

 

 

 

 

 

 

 

pcixx

slotnn

on|off

-

Turns on/off the LED of the PCI slot in the

 

 

 

 

 

PCIV/PCIX Unit. Slot number printed at the back

 

 

 

 

 

side of the Unit must be designated.

 

 

 

 

 

x” is the number of PCIV/PCIX Unit

 

 

 

 

 

(0-3).

 

 

 

 

 

nn” is the slot number printed at the back side

 

 

 

 

 

of the Unit.

 

 

 

 

 

 

 

gxbxy

busA|

slotn

on|off

Turn on/off the LED of the PCI slot in the

 

 

busB

 

 

PCIV/PCIX Unit according to physical control

 

 

 

 

number.

 

 

 

 

 

x” is the PCIV/PCIX Unit number

 

 

 

 

 

(0-3).

 

 

 

 

 

y” is the GXB number(0-3)in the PCIV /PCIX

 

 

 

 

 

Unit.

 

 

 

 

 

n” is the slot number(0-3)in the unit of GXB

 

 

 

 

 

bus.

 

 

 

 

 

 

 

fann

on|off

-

-

Turn on/off the LED of the Fan Unit in the Main

 

 

 

 

 

Chassis. “n” is the Fan Unit number.

 

 

 

 

 

 

loc

-

-

-

-

Used to specify location information manually.

 

 

 

 

 

Displays Help for “loc” when the argument is

 

 

 

 

 

omitted or an error is made.

 

 

 

 

 

This subcommand can be executed when all

 

 

 

 

 

partitions are in the DC POWER OFF state.

 

 

 

 

 

 

 

main

d

-

-

Specifies the location of the Main Chassis.

 

 

 

 

 

d” is the position of the lower edge of the

 

 

 

 

 

chassis from the bottom of the cabinet in

 

 

 

 

 

decimal (0-63)by using the EIA unit.

 

 

 

 

 

(1 EIA unit = 44.45mm)

 

 

 

 

 

 

3-44Service Processor

Table 3-35.HC Subcommands (cont’d)

cmd

arg1

arg2

arg3

arg4

Description

loc

pbayxy

d

h

-

Specifies the location and height of the Power

(cont’d)

 

 

 

 

Bay Unit in the cabinet.

 

 

 

 

 

x” is the unit ID number.

 

 

 

 

 

1: Power Bay Unit

 

 

 

 

 

0: Not allowed

 

 

 

 

 

y” is the ID number. (0) must be specified.

 

 

 

 

 

d” is the position of the lower edge of the unit in

 

 

 

 

 

decimal (0-63)by using the EIA unit.

 

 

 

 

 

(1 EIA unit = 44.45mm)

 

 

 

 

 

h” is the height of the unit (3).

 

 

 

 

 

 

 

pcixx

c

d

 

Specifies the location and height of the PCIX

 

 

 

 

 

Unit in the cabinet.

 

 

 

 

 

x” is the PCIX Unit number(1-3).

 

 

 

 

 

c” must be (1).

 

 

 

 

 

d” is the position of the lower edge of the unit in

 

 

 

 

 

decimal (0-63)by using the EIA unit.

 

 

 

 

 

(1 EIA unit = 44.45mm).

 

 

 

 

 

 

check

-

-

-

-

Checks the current configuration information

 

 

 

 

 

from the following points:

 

 

 

 

 

Presence of units whose location information

 

 

 

 

 

is not entered

 

 

 

 

 

Presence of “DISABLE” components

 

 

 

 

 

Presence of “INVISIBLE” units

 

 

 

 

 

Configuration violating the installation

 

 

 

 

 

restrictions

 

 

 

 

 

Configuration with penalty in

 

 

 

 

 

performance/RAS.

 

 

 

 

 

This subcommand can be executed in the AC

 

 

 

 

 

POWER ON state or DC POWER ON state.

 

 

 

 

 

 

Service Processor 3-45

Table 3-35.HC Subcommands (cont’d)

cmd

arg1

arg2

arg3

arg4

Description

clear

mmcxy

rowz

-

-

Clears the memory bit error counters of ROW.

 

 

 

 

 

x” is the physical CELLV Board number(0-3).

 

 

 

 

 

y” is the MMC number(0-1)within the CELLV

 

 

 

 

 

Board.

 

 

 

 

 

z” is the ROW number(0-3).

 

 

 

 

 

Each ROW has 3 counters. 3 counters are

 

 

 

 

 

cleared at the same time.

 

 

 

 

 

[Types of error counters]

 

 

 

 

 

Single bit error counter:

 

 

 

 

 

Counts in the unit of DIMM in the ROW.

 

 

 

 

 

Multi bit counter:

 

 

 

 

 

Counts in the unit of the ROW.

 

 

 

 

 

This subcommand can be executed in the AC

 

 

 

 

 

POWER ON state or DC POWER ON state.

 

 

 

 

 

 

 

Table 3-36.HC State Display Strings

 

 

Displayed String

Description

nonexist

Indicates that a component is defined as non-existent(i.e. the iSP manages a

 

component as if it does not exist).

 

 

INVISIBLE

The iSP manages a component as if it exists, but it does not exist when seen

 

from the iSP due to failure or other reasons.

 

Once it is recognized by the iSP (regardless of auto detection or manual setting),

 

it will be managed as if it exists unless you delete it explicitly using the “delete”

 

command.

 

 

power-off

Indicates that the power supply (DC) is OFF.

 

For some components, the power supply (DC) becomes ON when AC is

 

supplied.

 

 

power-on

Indicates that the power supply (DC) is ON.

 

For some components, it is overwritten by the following state display.

 

 

offline

Indicates that the power supply (DC) is ON and a component is not configured in

 

the software (OS or BIOS).

 

This applies to the CELLV Board, XIC/XBR Board, PCIV/PCIX Unit, and their

 

subcomponents.

 

 

online

Indicates that the power supply (DC) is ON and a component is configured in the

 

software (OS or BIOS).

 

This applies to CELLV Board, XIC/XBR Board, PCIV/PCIX Unit, and their

 

subcomponents.

 

 

master

This is valid only for the state display of the ISP-CBoard. Always Indicates that

 

it is operating as the master.

 

 

enable

Indicates that the component itself is enabled (used for system operation).

 

 

3-46Service Processor

Table 3-36.HC State Display Strings (cont’d)

Displayed String

Description

DISABLE

Indicates that the component itself is disabled (not used for system operation).

 

In this state, it is detached from the system manually with the “disable”

 

command.

 

 

DISABLE*

Indicates that the component itself is disabled (not used for system operation).

 

In this state, it is detached from the system due to failure of the component itself

 

or failure of the host interface.

 

It should not be configured in the system until the defective part is replaced.

 

 

DEG

Indicates that some subcomponents are in the DISABLE state.

 

 

Table 3-37.HC Help Screen

Screen Image

iSPyz:--->hcENTER> iSP FW version is Rxx.xx.

HC> help<ENTER>

HC command help :

help

: print this message.

disp

: display current status.

smem

: set size of shared memory of a partition.

attach

: attach CELLs and IORs to a partition.

detach

: detach CELLs and IORs from a partition.

swap

: swap CELLs in a partition.

add

: add a component.

delete

: delete a component.

enable

: enable a component.

disable

: disable a component.

online

: make a component online.

offline

: make a component offline.

ncconn

: connect 1.6G ports each other.

ncdis

: disconnect 1.6G ports.

led

: turn on/off maintenance LED of a component.

loc

: set location info.

clear

: clear memory bit error counters.

check

: check illegal configuration.

quit

: quit from HC command prompt.

A:Displays Help for the HC command when you enter “help”.

B:Displays the list of HC commands.

Reference

A

B

Service Processor 3-47

 

 

 

Table 3-38.HC ALL Display Screen

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Screen Image

 

 

 

 

 

 

 

 

 

 

 

Reference

iSPyz:---

> hcENTER>

 

 

 

 

 

 

 

 

 

 

 

iSP FW version is Rxx.xx.

 

 

 

 

 

 

 

 

 

 

HC> disp all<ENTER>

 

 

 

 

 

 

 

 

 

 

 

==== Partitioning ================================= 19:20:23,01/31/2002 ===

 

part0(RUN )

CELL:01--

(01--

)

IOR:0---

(0---

)

 

 

 

part1(INIT)

CELL:--

2-

(--

2-)

 

IOR:-1--

(-0--

)

 

 

A

part2(STOP)

CELL:---

3

(---

3)

 

IOR:

--2-(--0-)

 

 

part3(----

 

)

CELL:----

 

(----

)

IOR:----

 

(----

)

 

 

 

==================================================================

 

==== Summary (15/0/29+8F) ======================== 19:20:23,01/31/2002 ===

 

PBAY00 (loc=15/0/29+8F)

 

power-on

enable

DEG

 

 

PBAY01 (loc=15/0/23+6F)

 

power-on

enable

DEG

 

 

PBAY10 (loc=15/1/00+3F)

 

power-on

enable

DEG

 

 

iSP0

(loc=15/0/29+8F/30)

 

master -------

 

 

 

---

 

 

XBC0

 

(loc=15/0/29+8F/08)

offline

 

enable

DEG

 

 

XBC1

 

(loc=15/0/23+8F/09)

power-off

DISABLE

 

 

 

CELL0

(loc=15/0/29+8F/00)

online

 

enable

DEG

part.0 (LCN=0)

B

CELL1

(loc=15/0/29+8F/01)

offline

 

DISABLE

DEG

part.0 (LCN=1)

 

CELL2

(loc=15/0/23+8F/02)

online

 

enable

 

part.1 (LCN=3)

 

CELL3

(loc=15/0/23+8F/03)

power-off

enable

 

part.2 (LCN=2)

 

PCIX0(V) (loc=15/0/23+8F)

 

online

enable

 

DEG

part.0 (LIN=0,PRI=0)

 

PCIX1(F) (loc=15/0/17+4F)

 

offline

enable

 

DEG

part.0 (LIN=1,PRI=5)

 

PCIX2(F) (loc=15/0/19+4F)

 

online

enable

 

DEG

part.1 (LIN=0,PRI=0)

 

PCIX3(F) (loc=15/-/-----

)

 

power-offenable

 

DEG

part.2 (LIN=0,PRI=0)

 

==================================================================

 

----CELL0---------------------------------------------------------------------

 

 

 

 

 

 

 

 

 

 

19:20:23,01/31/2002 ---

 

CELL0 (loc=15/0/29+8F/00)

 

online

enable

 

DEG

part.0 (LCN=2)

 

PROC00

 

 

 

offline

DISABLE

---

 

 

PROC01

 

 

 

online

enable

 

---

 

 

PROC02

 

 

 

offline

DISABLE*

---

 

 

PROC03

 

 

 

nonexist.

 

 

 

 

 

 

MMC00

 

 

 

online

enable

 

DEG

 

C

MMC01

 

 

 

offline

enable

 

DEG

 

 

TAG0

 

 

 

---------

 

 

--------

 

DEG

 

 

CXI0

 

 

 

 

---------

 

 

enable

 

---

--->XBC0CXI0

 

CXI1

 

 

 

 

---------

 

 

disable

 

---

--->XBC1CXI0

 

IOM port0

 

 

 

---------

 

 

--------

 

---

IOR0-IOC1

 

IOM port1

 

 

 

---------

 

 

--------

 

---

IOR0-IOC0

 

----MMC00--------------------------------------------------------------------

 

 

 

 

 

 

 

 

 

 

19:20:23,01/31/2002 ---

 

MMC00

 

 

 

 

online

enable

DEG

 

 

ROW0[DIMM00:01] 1024MB

---------

 

enable

---

SBE=000:000 MBE=000

 

ROW1[DIMM10:11] 1024MB

---------

 

enable

---

SBE=000:000 MBE=000

 

ROW2[DIMM20:21] 1024MB

---------

 

DISABLE

---

SBE=000:000 MBE=000

D

ROW3[DIMM30:31] 1024MB

 

 

DISABLE

---

SBE=000:021 MBE=000

---------

 

 

cache000

 

 

 

 

---------

 

enable

---

 

 

cache001

 

 

 

 

---------

 

enable

---

 

 

cache002

 

 

 

 

---------

 

enable

---

 

 

cache003

 

 

 

 

---------

 

enable

---

 

 

cache004

 

 

 

 

---------

 

DISABLE*

---

 

 

cache005

 

 

 

 

---------

 

enable

---

 

 

cache006

 

 

 

 

---------

 

enable

---

 

 

cache007

 

 

 

 

---------

 

DISABLE

---

 

 

3-48Service Processor

Table 3-38.HC ALL Display Screen (cont’d)

Screen Image

 

 

 

 

Reference

----MMC01--------------------------------------------------------------------

 

 

 

19:20:23,01/31/2002 ---

 

MMC01

offline

enable

DEG

 

 

ROW0[DIMM00:01] 512MB ---------

 

enable

---

SBE=000:000 MBE=000

 

ROW1[DIMM10:11] 512MB ---------

 

enable

---

SBE=000:000 MBE=000

 

ROW2[DIMM20:21] 1024MB ---------

 

DISABLE

---

SBE=000:000 MBE=000

D

ROW3[DIMM30:31] 1024MB ---------

 

DISABLE

---

SBE=000:021 MBE=000

cache010 ---------

 

enable

---

 

 

cache011 ---------

 

enable

---

 

 

cache012 ---------

 

enable

---

 

 

cache013 ---------

 

enable

---

 

 

cache014 ---------

 

DISABLE*

---

 

 

cache015 ---------

 

enable

---

 

 

cache016 ---------

 

enable

---

 

 

cache017 ---------

 

DISABLE

---

 

 

----TAG0-----------------------------------------------------------------------

 

 

 

19:20:23,01/31/2002 ---

 

TAG0

---------

--------

DEG

 

 

TAG0e0 ---------

 

DISABLE

---

 

 

TAG0e1

---------

enable

---

 

 

TAG0e2 ---------

 

DISABLE*

---

 

 

TAG0e3

---------

enable

---

 

 

TAG0o0

---------

enable

---

 

E

TAG0o1 ---------

 

DISABLE

---

 

 

TAG0o2

---------

enable

---

 

 

TAG0o3

---------

enable

---

 

 

----CELL1---------------------------------------------------------------------

 

 

 

19:20:23,01/31/2002 ---

 

:

 

 

 

 

 

:

 

 

 

 

 

:

 

 

 

 

 

----XBC0 (XIC)---------------------------------------------------------------

 

 

 

19:20:23,01/31/2002 ---

 

XBC0 (loc=15/0/29+8F)

online

enable

DEG

 

 

CXI0

--------

enable

---

--->CELL0CXI0

 

CXI1

--------

DISABLE*

---

--->CELL1CXI0

 

CXI2

--------

enable

---

--->CELL2CXI0

 

CXI3

--------

DISABLE*

---

--->CELL3CXI0

 

1.6G port0 --------

 

enable

---

--->IOR0port0

F

1.6G port1

--------

DISABLE*

---

--->IOR1port0

 

MOVER0

--------

enable

---

 

 

MOVER1

--------

DISABLE

---

 

 

SERIAL0

--------

used

---

part.0

 

SERIAL1

--------

not used

---

 

 

SERIAL2

--------

used

---

part.1

 

SERIAL3

--------

disable

---

part.2

 

----XBC1 (XBR)--------------------------------------------------------------

 

 

 

19:20:23,01/31/2002 ---

 

XBC1 (loc=15/0/23+8F)

online

enable

DEG

 

 

CXI0

--------

enable

---

--->CELL0CXI1

 

CXI1

--------

DISABLE*

---

--->CELL1CXI1

 

CXI2

--------

enable

---

--->CELL2CXI1

 

CXI3

--------

DISABLE*

---

--->CELL3CXI1

 

1.6G port0 --------

 

enable

---

--->IOR2port0

 

1.6G port1

--------

DISABLE*

---

--->IOR3port0

 

MOVER0

--------

enable

---

 

 

MOVER1

--------

DISABLE

---

 

 

SERIAL0

--------

used

---

part.0

 

SERIAL1

--------

not used

---

 

 

SERIAL2

--------

used

---

part.1

 

SERIAL3

--------

disable

---

part.2

 

Service Processor 3-49

Table 3-38.HC ALL Display Screen (cont’d)

Screen Image

 

 

 

 

 

Reference

----PCIX0(V)------------------------------------------------------------------

 

 

 

 

19:20:23,01/31/2002 ---

 

IOR0 (loc=15/0/29+8F)

online

enable

DEG

part.0 (LIN=0,PRI=0)

 

1.6G port0 --------

 

enable

---

--->XBC0port0

 

IOC00

--------

enable

DEG

 

 

IOC01

--------

enable

DEG

 

 

GXB00 (loc=15/0/29+8F) --------

 

enable

---

 

 

BUS-A

--------

enable

---

BIO

G

BUS-B

--------

enable

---

 

 

GXB01 (loc=--/-/--+--)

--------

nonexit

---

 

 

BUS-A

--------

nonexit

---

 

 

BUS-B

--------

nonexit

---

 

 

GXB02 (loc=15/0/29+8F) --------

 

enable

---

 

 

BUS-A

--------

enable

---

 

 

BUS-B

--------

enable

---

 

 

GXB03 (loc=15/0/29+8F) --------

 

enable

---

 

 

BUS-A

--------

enable

---

 

 

BUS-B

--------

enable

---

 

 

----PCIX2(F)------------------------------------------------------------------

 

 

 

 

19:20:23,01/31/2002 ---

 

IOR2 (loc=15/0/13+4F)

offline

enable

DEG

part.0 (LIN=2,PRI=9)

 

1.6G port0 --------

 

enable

---

--->XBC2port0

 

IOC20

--------

enable

DEG

 

 

IOC21

--------

enable

DEG

 

 

GXB20 (loc=15/1/13+4R) --------

 

enable

---

 

 

BUS-A

--------

enable

---

BIO

 

BUS-B

--------

enable

---

 

 

GXB21 (loc=15/1/13+4R) --------

 

enable

---

 

 

BUS-A

--------

enable

---

 

 

BUS-B

--------

enable

---

 

 

GXB22 (loc=15/1/13+4R) --------

 

enable

---

 

 

BUS-A

--------

enable

---

 

 

BUS-B

--------

enable

---

 

 

GXB23 (loc=15/1/13+4R) --------

 

enable

---

 

 

BUS-A

--------

enable

---

 

 

BUS-B

--------

enable

---

 

 

:

 

 

 

 

 

 

:

 

 

 

 

 

 

:

 

 

 

 

 

 

----PBAYs---------------------------------------------------------------------

 

 

 

 

19:20:23,01/31/2002 ---

 

PBAY00 (loc=15/0/23+8F)

power-on

enable

DEG

 

DPS000

 

 

 

 

 

 

DPS001

INVISIBLE

 

 

 

 

DPS002

 

 

 

 

 

 

PBAY01 (loc=15/0/23+8F)

power-on

enable

DEG

 

DPS010

INVISIBLE

 

 

 

H

DPS011

 

 

 

 

DPS012

 

 

ALARM

 

 

 

PBAY10 (loc=15/1/00+3F)

power-on

enable

DEG

 

DPS100

 

 

 

 

 

 

DPS101

 

 

 

 

 

 

DPS102

 

 

 

 

 

 

DPS103

INVISIBLE

 

 

 

 

DPS104

 

 

ALARM

 

 

 

DPS105

 

 

 

 

 

 

 

 

 

 

 

 

 

3-50Service Processor