NAVMAN TRACKER 500, TRACKER 500I User Manual

0 (0)
NAVMAN TRACKER 500, TRACKER 500I User Manual

w w w . n a v m a n . c o m

TRACKER 500/500i

G P S N A V I G A T I O N

Addendum

 

ENGLISH ...............................................................................

2

 

FRANÇAIS – FRENCH ..................................................

....... 3

 

DEUTSCH – GERMAN..........................................................

4

 

NEDERLANDS – DUTCH .....................................................

5

 

SVENSKA – SWEDISH .........................................................

6

 

ESPAÑOL – SPANISH ...................................................

....... 7

Printed in New Zealand

NAVMAN®

1950853A

LA000053

 

Addendum to NAVMAN’s Tracker 500/500i Owner’s Manual

New feature – Centre on boat / follow boat.

Once the -ctr- key combination (simultaneous press of zoom-in and zoom-out) is pressed the track plot screen will follow the boat until the mode is “unlocked”. Unlocking is by panning the track plot screen (when the cursor gets to the edge of the screen), or zooming in until the boat moves outside the central area of the screen. Activation of the centre on boat mode feature is indicated by a small hollow boat diamond between the speed and heading on the bottom line of the track area.

Note: This feature will be activated by default on power up and may be activated from anywhere, not only the track screen, compared with the earlier centre feature noted on P9 of the manual. The unit will switch to the track plot screen whenever the - ctrkey combination is pressed.

New feature – 3 Configurable alarms

The highway width is no longer changed in the setup menu as indicated on P33 of the manual. This setting has been replaced with an “ALARM” menu with settings for 3 alarms.

1) Highway XTE alarm.

When the setting “HIGHWAY” is turned on, the XTE (Cross track error) is continually monitored while navigating to a waypoint. If the boat moves outside the selected highway screen road width, an alarm prompt will be shown, and the buzzer will sound.

Notes: 1) The alarm will reactivate every time the boat moves inside the highway screen road width, then strays outside it again. 2) The highway screen does not have to be showing for the alarm to activate.

2) 1 MINUTE alarm

When the setting “1 MINUTE” is turned on, the TTG (Time to go) is continually monitored while navigating to a waypoint (during navigation of a route, the setting is active for each waypoint in the route). The first time that the TTG drops below 1 minute, an alarm prompt will be shown, and the buzzer will sound.

Note: The alarm will not reactivate if the TTG raises above 1 minute, then drops below 1 minute again.

3) Anchor drag alarm.

When the setting “ANCHOR” is turned on, the change in position is continually monitored. If the boat moves a distance greater than that set by “ANCHOR 0.xx” from the boat’s position when “ANCHOR SET >” was activated, an alarm prompt will be shown, and the buzzer will sound.

Notes: 1) The alarm will reactivate every time the boat moves inside the anchor circle, then strays outside it again. 2) Without DGPS (Differential GPS), selective availability may cause the reported position to deviate by up to 900 feet. This will trip

the anchor alarm, the distance of “ANCHOR 0.xx” may need to be increased.

New feature - Distance log.

The position screen as pictured on P15 of the manual now also displays distance travelled since last cleared. This works by measuring a succession of straight lines (similar to the track drawing). This means that it will not be highly accurate if you drive around in small circles (e.g. 600ft) all day. However, if you forget to turn it on at the start of the journey, you will still get a good approximation of the distance from the position where the unit last had a fix. The distance units setting as indicated on P34 of the manual has been replaced by a distance menu, which allows clearing of the distance log and setting of the distance units.

New feature – User configurable waypoint display.

New options have been added to enhance the display of waypoints on the track screen.

On the waypoint edit screen (see P25 of the manual), two extra settings have been added. “NAME | ON/OFF”, “SYMBOL | ON/OFF”. By default, when a new waypoint is created, only the symbol will be shown on the track screen. Turning the name display on will cause the waypoint’s name to be displayed to the right of the waypoint on the track screen. Turning the symbol display off will prevent the waypoint from being shown on the track screen.

Notes: 1) Turning the symbol off does not delete the waypoint. The waypoint can simply be selected from the waypoint list and the symbol turned back on again. 2) You cannot have the waypoint name turned on, and the waypoint symbol turned off.

On the main waypoint menu (see P22 of the manual), two extra settings have been added. “NAMES | ALL/NONE/SEL.”, “SYMBOLS | ALL/ NONE/SEL.” When SEL. (short for SELECTED) is chosen the name/symbol will be displayed according to each individual waypoint setting. When ALL is chosen, the name/symbol will be displayed regardless of each waypoint setting. When NONE is chosen, the name/symbol will not be displayed regardless of each waypoint setting.

Note: You cannot have the waypoint names turned on, and the waypoint symbols turned off.

New feature – Goto key.

Holding the zoom-in key, while any screen is showing, will take you immediately to the GO, TO WAYPOINT, TO MARK, ALONG ROUTE screen as shown on P21 of the manual.

Note: If you are already navigating to a waypoint, an option will first be presented asking whether you want to cancel that navigation first.

2

New feature – Waypoint key.

Holding the zoom-out key, while any screen is showing, will take you immediately to the WAYPOINTS menu as shown on P22-25 of the manual.

Note: While the track plot screen is showing, and the cursor is positioned immediately over a waypoint, the shortcut will take you directly to the

screen for that particular waypoint.

Change in operation – highway width.

The highway width is no longer changed in the setup menu as indicated on P33 of the manual.

The zoom-in and zoom-out keys will alter the highway width when the highway screen is displayed.

Addendum à la notice du GPS NAVMAN Tracker 500/500i

Nouvelle Fonction - Centrage du bateau/ Suivi du bateau

Les touches -ctr- (appuyez simultanément sur les touches zoom-in et zoom-out), permettent de centrer le bateau sur l'écran et ainsi de le suivre. Pour déverrouiller l'écran Trace, le faire défiler (en déplaçant le curseur vers le bord de l'écran) ou zoomer pour obtenir plus de détails jusqu'à ce que le bateau sorte de l'écran. En bas de l'écran Trace, entre les indications de vitesse et de cap du bateau, un symbole diamant indique que cette fonction centrage du bateau est activée.

Remarque : cette fonction est automatiquement activée à la mise en route de l'appareil. Elle est également disponible à partir de n'importe quel écran et pas seulement à partir de l'écran Trace comme dans les versions antérieures. L'appareil affiche l'écran Trace dès que vous appuyez sur les touches -ctr-.

Nouvelle fonction - 3 Alarmes

La largeur de la Route n'est plus modifiableà partir du menu Paramètres (p 73 de la notice). Cette fonction a été remplacée par le menu "Alarme" qui permet de paramétrer les 3 alarmes suivantes :

1) Alarme Highway - Ecart de Route (XTE CrossTrack Error)

Lorsque vous activez la fonction Highway, l'écart de route (XTE, Cross Track Error) est alors sous surveillance lorsque vous vous dirigez vers un waypoint. Si votre bateau sort du couloir de navigation sélectionné, l'alarme visuelle et sonore se déclenchent.

Remarque : 1) l'alarme s'activeraàchaque fois que votre bateau ressortira du couloir de navigation. 2) L'alarme s'activeême si vous n'êtes pas en écran Highway.

2) Alarme 1 minute

Lorsque vous activez cette alarme : le temps à l'arrivée (TTG Time to go) est alors sous surveillance lorsque vous vous dirigez vers un waypoint (lorsque vous suivez une route, cette alarme s'applique pour tous les waypoints de la route). Lorsque ce temps à l'arrivée est inférieur à une minute, l'alarme visuelle et sonore se déclenchent.

Remarque : L'alarme ne s'activera pas si le TTG repasse au-dessus d'une minute et redescend sous la minute.

3) Dérive de mouillage

Lorsque vous activez l'alarme de dérive de mouillage, la dérive du bateau est continuellement surveillée. Une alarme visuelle et sonore se dé clenche lorsque la dé rive du bateau est supérieure à la dérive maximum sélectionnée ANCRE 0.XX, par rapport à la position initiale du bateau (cette position initiale correspond à la position du bateau au moment de l'activation de la fonction ANCRE SEL.

Remarque : 1) L'alarme se déclenchera à chaque fois que le bateau sortira de la zone de dérive maximum. 2) Si vous ne possédez pas de DGPS (différentiel GPS), la disponibilité sélective (SA), peut dégrader la position reportée d'environ 300 mètres. Ceci peut entraîner le déclenchement de l'alarme. Dans ce cas, il sera né cessaire d'augmenter la distance maximum de dérive ANCRE 0.XX.

Nouvelle fonction Loch

L'écran Position représenté page 55 du manuel affiche désormais la distance parcourue depuis la dernière remise à zéro. Cette distance est calculée en additionnant une succession de lignes droites (similaire au calcul des points de la trace). La fonction Unités du menu Paramètres page 74 a été remplacée par un menu distance qui permet de remettre à zéro la distance parcourue et de choisir les unités de distance désirées.

Nouvelle fonction -Ecran Waypoint

Pour améliorer l'affichage des waypoints surécranl' Trace, deux nouvelles fonctions ont été ajoutées sur l'écran d'édition d'un waypoint (page 65) : Noms ON/OFF et Symbole ON/OFF. Par défaut, lorsque qu'un nouveau Waypoint est créé , seul le symbole de ce waypoint apparaît sur l'écran Trace. Si vous activez l'affichage du nom du waypoint, ce nom s'afficheraà droite du waypoint sur l'écran Trace. Si vous désactivez l'affichage du symbole, ce waypoint ne sera pas affiché sur l'écran Trace.

Remarque : 1) Le fait de désactiver l'affichage du symbole Waypoint ne supprime pas ce waypoint. Il suffit de le sélectionner dans la liste des waypoints pour que son symbole s'afficheà nouveau. 2) Remarque : Il n'est pas possible d'activer l'affichage du nom d'un waypoint sans activer l'affichage du symbole.

Dans le menu principal Waypoint (voir page 62),

3

Loading...
+ 5 hidden pages