Navman 8084, 8120 User Manual

0 (0)

Navman

8120/8084

Fuel, AIS, & Radar

Addendum 06/07

w w w . n a v m a n . c o m

Warning

AIS: The AIS features on this chart-plotter are designed as a safety aid only and do not guarantee safety at sea. AIS transmission is mandatory on some, but not all, vessels. AIS should be used to complement radar, but AIS is not a substitute for radar.

Notes

AIS and Radar functions require optional accessories to be installed.

Radar is available in 2 kW, 4 kW, 6 kW units.

• The setup menu can be opened by pressing

twice (8084) /

(8120) then select System:

 

Sonar

Disable any sonar transducer and disable sonar functions.

A sonar transducer is fitted. Enable sonar operation.

Radar

No appropriate Radar system is fitted. Disable RADAR.

An appropriate Radar receiver is fitted.

Enable Radar.

AIS

No appropriate AIS receiver is fitted. Disable AIS.

An appropriate AIS receiver is fitted.

Enable AIS.

Appendix

8084 Size: 190 mm (7.48“) H x 285 mm (11.22“) W x 76.8 mm (3.02“) D. Allow 3 mm clearance on each side for dust cover.

8084 Display: 213.4 mm (8.4”) diagonal, TFT color, 800 x 600 pixels.

CPA - Closest Point of Approach. The closest distance two vessels will come to each other based on their current course and speed.

Radar guard zone - An area around the boat, set up by the operator and defined by distance and bearing. If an object (e.g. another boat) enters the radar guard zone, an alarm is activated.

Rain clutter - Heavy rain or snow can cause interference with the radar image.

Range (radar) - The distance between the centre of the radar image and the outer range ring. The scale is shown in the top left corner of the radar window.

Range rings - Concentric circles extending from your boat (usually at the centre of the radar window) and used to estimate distances to objects. The scale is shown in the top left corner of the radar window.

Route - Two or more waypoints linked in sequence to form a course for the boat. Sea clutter - Rough seas can cause interference with the radar image.

2

NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum

Fuelfunctionsanddisplay

What the fuel computer does

! WARNING

To ensure the fuel data is accurate:

When you add or remove fuel from a tank, tell the 8120/8084.

If the boat has petrol/gasoline sensors, calibrate them during installation or if the fuel readings seem inaccurate.

Choose an appropriate type of boat speed sensor or GPS source to calculate economy, range and the fuel consumption curve.

If the boat uses a paddlewheel sensor to measure speed, calibrate it during installation or if the speed readings seem inaccurate.

Low fuel alarm

To set a low fuel alarm for a tank:

1 Press twice, select Fuel, then select

Setup tanks.

2On a multi-tank boat, select the tank to set the alarm for.

3Select Tank alarm and enter a fuel level to trigger the low fuel alarm; or enter zero to disable the alarm.

When a low fuel alarm is set, the alarm’s fuel level is shown on the fuel display tank levels as a red bar. The alarm can also be set using the Alarms setup menu.

Boat speed sensors

Selecting a boat speed sensor

To select an optional speed sensor

The fuel calculations can use boat speeds from the GPS, or from a paddlewheel sensor or pitot sensor if these optional sensors are installed:

Paddlewheel and pitot sensors measure the speed through the water; GPS speed is speed over ground; these sensors can give different values for Range, Economy and the fuel consumption curves.

A pitot sensor is more accurate than a paddlewheel sensor at high speeds but is not accurate at low speeds. A paddlewheel sensor is more accurate than a pitot sensor at low speeds.

1Press twice, select Fuel, then select

Speed source.

2To use a paddlewheel or pitot sensor, select Water speed, otherwise select Ground speed to use GPS speed.

3If you selected Water speed and you have both a paddlewheel sensor and a pitot sensor:

iPress , select SmartCraft and select Speed type

ii Select Paddlewheel or Pitot.

Tip: You can select a different speed sensor during a trip.

NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum

3

Water speed and ground speed

A paddlewheel sensor and a pitot sensor measure water speed, the boat speed through the water. A GPS measures ground speed, the boat speed over the bottom of the water. If there is a current, then these speeds will be different, and the log, trip log, economy and range will be different, as shown below.

Water speed is better for measuring the boat’s potential performance, Ground speed is better for going to a destination because it takes currents into account.

When the current is from ahead, ground speed is less than water speed

Water speed 10 knots

 

Water speed 10 knots

 

Current 4 knots

 

 

Gives a ground speed of 6 knots

 

Gives a ground speed

 

 

 

of about 8 knots

Current 4 knots at 45º

For this example:

 

 

 

 

If the boat travels for one hour, uses 3 gallons of fuel per hour and has 50

gallons of fuel left:

 

 

 

 

 

Speed

Log

Economy

Range

Using water speed:

10 knots

10 nm

3.3 nm / gal

165 nm

Using ground speed:

6 knots

6 nm

2.0 nm / gal

100 nm

When the current is from behind, ground speed is more than water speed

Water speed 10 knots

Current 4 knots

Water speed 10 knots

Current 4 knots at 45º

Gives a ground speed of 14 knots

Gives a ground speed of about 13 knots

 

For this example:

 

 

 

 

If the boat travels for one hour, uses 3 gallons of fuel and has 50 gallons of fuel left:

 

Speed

Log

Economy

Range

Using water speed:

10 knots

10 nm

3.3 nm / gal

165 nm

Using ground speed:

14 knots

14 nm

4.7 nm / gal

235 nm

4

NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum

Calibration

Calibrate petrol/gasoline fuel flow sensors during installation, or if the fuel readings seem inaccurate and the other troubleshooting suggestions do not help.

Note

SmartCraft fuel sensors and NAVMAN diesel sensors are factory calibrated and should never need recalibrating.

On a multi engine boat, calibrate each engine’s sensor. This can be done at the same time with a portable tank for each engine or at different times using one portable tank.

Calibrating a sensor requires accurate measurement of the fuel consumption. This is best done using a small portable tank. At least 4 gallons (15 litres) of fuel should be used to ensure an accurate calibration.

It is often very difficult to fill underfloor tanks to the same level twice due to air pockets, so the more fuel used, the more accurate the calibration.

To calibrate the sensor(s):

1 Record the level of the fuel in the tank(s).

2Connect the portable tank(s) to the engine through the fuel sensor(s).

3Run the engine at normal cruising speed until at least 4 gallons (15 litres) of fuel has been used per engine.

4Check the actual amount of fuel used per engine by refilling the portable tank(s) to the original level and noting the reading(s) of the fuel dispenser’s gauge.

5Press twice, select Fuel, then select

Setup engines.

6On a single engine boat, select Calibrate and change the displayed value to be equal to the reading of the fuel dispenser’s gauge, then press .

On a multi-engine boat select the engine. Select Calibrate and change the displayed value to be equal to the reading

of the fuel dispenser’s gauge, then press . Repeat for the other engines.

NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum

5

Navman 8084, 8120 User Manual

AIS

AIS is short for Automatic Identification System. The International Convention for Safety of Life At Sea (SOLAS) requires all vessels greater than 300 tons and all

passenger vessels to be equipped with AIS Transponders. All vessels equipped with AIS permanently broadcast via one or more of the two dedicated VHF channels. This transmission may include information about the vessels MMSI-number, its call sign, name, position, course, heading, speed, rate of turn and type of vessel.

This unit can receive and display AIS information when connected to an AIS receiver. Available AIS vessels transmitting in

the local area are shown on the chart when this feature is enabled.

The following AIS receivers are supported by this unit:

Comar SLR200 (external GPS).

Weatherdock Two Channel AIS Receiver “EASY AIS”, Part No. 5-A-013 (external GPS).

NASA Marine AIS Engine 2 channel MultiPlex Receiver (external GPS).

Other AIS receivers may work but have not been tested with this unit.

To enable AIS from the system menu check the AIS box.

Viewing AIS Vessels

A typical AIS window shows:

E

B A C

A AIS Vessel

B Dangerous Vessel

C Projected Course

D Data Box

E Range Rings

6

NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum

When the cursor is placed over an AIS vessel for at least two seconds, a data box appears at the bottom of the window with information about the AIS vessel.

For complete AIS information of the AIS vessel place the cursor over an AIS vessel for at least two seconds and press .

Press either or to clear the information.

Dangerous Vessels

The 8120/8084 calculates the time of closest point of approach (TCPA) and closest point of approach (CPA) for each AIS vessel.

This is used to determine potential dangerous vessels. If the TCPA and the CPA is below the trigger values then it will be considered dangerous.

A dangerous vessel is indicated on the chart by a red circle around the icon.

TCPA 15 min

CPA 0.5 nm

AIS Windows

 

To go to the AIS windows, press

, select

More, select AIS, then press or to select

one of the two windows: Vessels or Safety

msgs (rx).

 

If there are more items than will fit on the

window, press or to see the others.

 

 

 

 

Vessels This is a sorted list of vessels currently being received by the AIS receiver. The maximum number of vessels that the system will support is 250. Once maximum is reached, vessels furthest away from the current location will be replaced. A vessel will be removed from the list if no information is received within 6 minutes from the last message.

Displaying an AIS vessel on the chart 1 Press or to select a vessel.

2Press and select Display. The Instrument switches to chart window, with the selected vessel position in the middle.

Displaying Full AIS Details

1

Press or to select a vessel.

2Press and select More Info or press .

NAVMAN 8120/8084 Fuel, AIS, & Radar Addendum

7

Loading...
+ 14 hidden pages