Nauto N3 User Manual

USER GUIDE

Nauto Device & Mark Button

US Installation Guidelines Last updated: June 2019

Table of Contents

Overview 3

Installation Tool List

Nauto Components

OBD Adapter Reference

Installation

Power Source Connection

OBD Connection

Power Cable Connection

Device Registration

Device Installation

Vehicle Information

Mark Button

Image Submission

Additional Resources

Nauto Installation Guide | Overview

PURPOSE

The purpose of this document is to provide guidelines for the installation of the Nauto Device. The installation guidelines, specifications, materials and examples provided in this document are for information purposes only, are non-exhaustive, and shall not be relied upon for the specific installation in any vehicle. This guide is not intended to replace other regulatory requirements in the jurisdiction where the Nauto Device is installed or used.

Before starting the Nauto Device installation and configuring the system, please ensure that you have read this guide thoroughly. If you have any questions or concerns regarding the installation of the Nauto Device, please contact Nauto Support at 1 (888) 628-8690 or support@nauto.com.

WARNING

This equipment may only be located in a position where it cannot interfere with the normal and safe operation of the vehicle, or present a hazard to the driver, or passengers. When routing all cables ensure that the insulation does not become worn or damaged. All cabling must be secured utilizing industry standard methods.

If you are unsure about the placement or installation of this equipment, stop work, and contact your Nauto representative immediately.

Under no circumstances should any part of the Nauto system be installed inside the engine compartment area.

This equipment should not be operated in hazardous environments, or areas that contain explosive materials or flammable vapors.

This equipment should not be operated in aircraft or in close proximity to medical equipment.

Unauthorized changes or alterations to the equipment may invalidate Nauto warranty, and may also affect the vehicle manufacturers warranty.

DISCLAIMER & SAFETY INFORMATION

Due to ongoing development, information and specifications may change at any time without notice. While the information is believed to be accurate, it may include errors or inaccuracies. Nauto shall not be liable for any use of the installation guide or information supplied.

The installation of the Nauto Device may adversely affect other vehicle components or safety equipment. Nauto assumes no responsibility and disclaims any liability for any damage to any vehicle components, safety equipment, or bodily injury that may arise due to installation or use of Nauto’s products and services.

THE INFORMATION ON THIS INSTALLATION GUIDE IS PROVIDED "AS IS" AND TO THE EXTENT PERMITTED BY LAW, IS PROVIDED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT. Nauto shall not be liable for any damages, losses, costs or expenses, direct, indirect or incidental, consequential or special, resulting from the use of this installation guide.

This guide is not written for any specific vehicle since the proper wiring and installation of electronics differs for each vehicle. Installation should be completed by qualified individuals who are trained to wire electronics such as the Nauto Device. It is your responsibility to know how to wire in electronics such as the Nauto Device for your specific vehicle. Improper wiring may cause injury or damage and void the warranty. Any changes or modification to the Nauto Device not expressly approved by Nauto or the entity responsible for compliance may void any warranties and your authority to operate the Nauto Device.

This installation guide contains proprietary information that is protected by copyright. All rights are reserved. This guide may not be copied, reproduced, or translated into another language without Nauto’s prior written consent.

Safety Warnings

DO NOT INGEST BATTERY. CHEMICAL BURN HAZARD

The Nauto mark button supplied with the N3 device contains a coin/button cell battery. If the coin/button cell battery is swallowed it can cause severe internal burns in just 2 hours and can lead to death.

Keep new and used batteries away from children.

If the battery compartment does not close securely, stop using the product and keep it away from children.

If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

CAUTION

Risk of explosion if the battery is replaced with an incorrect type.

Compliance Statements

FCC STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

signed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio

de frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Content:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures.

2. This equipment is authorized only for Fixed or Mobile applications and is required to be installed as such.

3. This equipment must be installed and operated with a minimum separation of 20 cm (8 in.) between the equipment and users/bystanders at all times.

IC STATEMENT

"This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device." or "Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

1) l’appareil ne doit pas produire de brouillage; 2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement." Déclaration sur l'exposition aux rayonnements RF L'autre utilisé pour l'émetteur doit être installé pour fournir une distance de séparation d'au moins 20 cm de toutes les personnes et ne doit pas être colocalisé ou fonctionner conjointement avec une autre antenne ou un autre émetteur.

Installation Tool List

The following tools are recommended to perform installation of the Nauto Device.

q Digital multimeter with sharp leads (or wire

piercing leads)

q Razor knife

q 3M Super 33 electrical tape

q Wire strippers (self strippers)

q Wire crimpers (capable of crimping insulated

terminals)

q Deep 1/4" drive metric sockets (5.5 mm

and 7-13mm)

q T5 To rx driver with handle

q Tri m panel removal tool

q 8” or 11” black zip/nylon ties

q 18 AWG ring terminals

q #6 x ½ in. self tapping screws

q Compact cordless 1/4" impact driver with hex

drive

q #2 Phillips drill bit

The following tools are recommended based on the preferred connection method:

Connection Method Description Recommended Tools

Poke & Wrap

This solution requires splicing into a low voltage wire for a connection.

• 18 AWG nylon butt connectors (2 or 3)

Posi-Tap

Solder

This solution requires posi-tap connectors to tap into wires without cutting or splicing.

This solution requires a heated tool to bond wires together using a filler metal with a low melting point.

• Proper sized posi-taps

• Soldering iron

Nauto Components

Nauto Device

12V Power Supply Adapter

Windshield Mount

(Optional)

3-wire power supply

with OBD Y-cable connector

Mark Button

Note: Do not dispose of small bag

with “MAC address” label.

Fuse Holder

with 3.5amp fuse

Hardwire Power Cable

(12v and 24V)

OBD Adapters

See reference guide on page 6.

+ 15 hidden pages