Nautilus E614 User Manual

0 (0)

ASSEMBLY MANUAL / OWNER’S MANUAL

TABLE OF CONTENTS

Important Safety Instructions - Assembly	3	Operations	28
Safety Warning Labels / Serial Number	4	Adjustments	28
Specifications	5	Power Up / Idle Mode	29
Before Assembly	5	Initial Setup	29
Parts	6	Quick Start Program	30
Hardware	7	User Profiles	30
Tools	7	Profile Programs	32
Assembly	8	Pausing or Stopping	34
Moving the Machine	20	Results / Cool Down Mode	35
Leveling the Machine	20	GOAL TRACK Statistics	35
		Console Service Mode	37
Important Safety Instructions	21	Maintenance	38
Features	22	Maintenance Parts	39
Console Features	23	Troubleshooting	40
Contact Heart Rate	26	Warranty	42

To validate warranty support, keep the original proof of purchase and record the following information:

Serial Number __________________________

Date of Purchase ____________________

To register your product warranty , go to: www.Nautilus.com/register Or call 1 (800) 605–3369.

If you have questions or problems with your product, please call 1 (800) NAUTILUS (628–8458).

Nautilus, Inc., (800) NAUTILUS / (800) 628-8458, www.NautilusInc.com - Customer Service: North America (800) 605-3369, csnls@nautilus.com | outside U.S. +01-360-859-5180, technics@nautilus.com | © 2013 Nautilus, Inc. | ® indicates trademarks registered in the United States. These marks may be registered in other nations or otherwise protected by common law. MyFitnessPal® is a registered trademark of its owner.

IMPORTANT SAFETY INSTRUCTIONS -ASSEMBLY

This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Obey the following warnings:

Read and understand all warnings on this machine. Carefully read and understand the Assembly instructions.

•Keep bystanders and children away from the product you are assembling at all times.

•Do not connect power supply to the machine until instructed to do so.

•Do not assemble this machine outdoors or in a wet or moist location.

•Make sure assembly is done in an appropriate work space away from foot traffic and exposure to bystanders.

•Some components of the machine can be heavy or awkward. Use a second person when doing the assembly steps involving these parts. Do not do steps that involve heavy lifting or awkward movements on your own.

•Set up this machine on a solid, level, horizontal surface.

•Do not try to change the design or functionality of this machine. This could compromise the safety of this machine and will void the warranty.

•If replacement parts are necessary, use only genuine Nautilus replacement parts and hardware. Failure to use genuine replacement parts can cause a risk to users, keep the machine from operating correctly and void the warranty.

•Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Manual.

•Read and understand the complete Manual supplied with this machine before first use. Keep the Manual for future reference.

•Do all assembly steps in the sequence given. Incorrect assembly can lead to injury or incorrect function.

•This product contains magnets. Magnetic fields can interfere with the normal use of certain medical devices at a close range. Users may come into proximity of the magnets in the assembly, maintenance, and/or use of the product. Given the obvious importance of these devices, such as a pacemaker, it is important that you consult with your medical provider in connection with the use of this equipment. Please consult the “Safety Warning Labels and Serial Number” section to determine the location of the magnets on this product.

SAFETY WARNING LABELS AND SERIAL NUMBER

Product Specification

Serial Number

•Read, understand and obey all warnings on this machine.

•Keep children away.

•Not intended for use by anyone under 14 years of age.

•Prior to use, read and understand the Owner’s Manual.

•Injury or death is possible if Caution is not used while using this machine.

•The maximum user weight for this machine is 300 lbs (136 kg).

•Replace any “Caution”, “Warning” or “Danger” label that is illegible, damaged, or removed.

•The heart rate displayed is an approximation and should be used for reference only.

•

FCC Compliance

!Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The machine and power supply comply with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This machine and power supply have been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

			SPECIFICATIONS
		Maximum User Weight:	300 lbs. (136 kg)
		Machine Weight:	167.3 lbs. (75.9 kg)
	63.2”	Power Requirements:
	(160.5 cm)	Power Requirements:
	(160.5 cm)	Operational Voltage: 9VDC
		Operational Voltage: 9VDC
		Operating Current:	1500 mA
		Regulatory Approvals:
	71.5”	AC Power Adapter:	UL listed, Rated 120V 60Hz Input, 9VDC,
26.7”	(181.7 cm)		1500mA Output. Class 2.
(67.7 cm)

This product, its packaging, and components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This Notice is provided in accordance with California’s Proposition 65. If you would like additional information, please refer to our website at www.nautilus.com/prop65.

Before Assembly

Select the area where you are going to set up and operate your machine. For safe operation, the location must be on a hard, level surface. Allow a workout area of a minimum 76” x 120” (193 cm x 305 cm). Be sure that the workout space you are utilizing has adequate height clearance, taking into consideration the height of the user and the maximum incline of the elliptical machine.

Basic Assembly Tips

Follow these basic points when you assemble your machine:

•Read and understand the “Important Safety Instructions” before assembly.

•Collect all the pieces necessary for each assembly step.

•Using the recommended wrenches, turn the bolts and nuts to the right (clockwise) to tighten, and the left (counterclockwise) to loosen, unless instructed otherwise.

•When attaching 2 pieces, lightly lift and look through the bolt holes to help insert the bolt through the holes.

•The assembly can require 2 people.

PARTS

			1	5	6
				5	6
19	21		2
19			3		7
			3		7
	20			4	8
				4
					10
		16			9
	17	16		13
				13

18
	15			12
				12
	14				11

A decal has been applied to all right (“ R ”) and left (“ L ”) parts to assist with assembly.

Item	Qty	Description	Item	Qty	Description
1	1	Console	12	1	Left Leg

2	1	Shroud Cap	13	1	Frame
3	1	Console Mast	14	1	Front Stabilizer
4	1	Arm Pivot Rod	15	1	Right Leg
5	1	Static Handlebar	16	1	Upper Shroud
6	1	Water Bottle Holder	17	1	Right Pedal
7	1	Manual Lift Assembly	18	1	Lower Right Handlebar Arm
8	1	Upper Left Handlebar Arm	19	1	MP3 Cord
9	1	Lower Left Handlebar Arm	20	1	Upper Right Handlebar Arm
10	1	Rail Assembly	21	1	AC Adapter
11	1	Left Pedal	22	1	Silicone Lubricant, Bottle (not shown)

HARDWARE / TOOLS

A B C D E F G H I

Item	Qty	Description	Item	Qty	Description

A	6	Button Head Hex Screw, M8x16 (with	F	6	Wave Washer
		Loctite® adhesive)
B	4	Flat Washer, M8	G	12	Lock Washer, M8
C	8	Wide Washer, M8	H	2	Pivot Sleeve
D	4	Button Head Hex Screw, M8x16	I	2	Cap
E	2	Hex Head Screw, M8x20

Tools

Included	Not Included
6 mm	(recommended)

13 mm

15 mm

19 mm

ASSEMBLY

1. Attach Front Stabilizer to Frame

Note: Hardware (*) is pre-installed and not on the Hardware Card.

6mm

2. Attach Rail Assembly to Frame Assembly

Note: Be sure Levelers are fully raised on Rail Assembly. Hardware (*) is pre-installed and not on the Hardware Card.

6mm

10 *

* *

3. Attach the Manual Lift Assembly using the Arm Pivot Rod

Note: Hardware (*) is pre-installed and not on the Hardware Card.

NOTICE: With the Arm Pivot Rod under the straight section of tube near the front, push the Manual Lift Assembly toward the Frame Assembly and fully tighten hardware. Remove the Arm Pivot Rod after tightening.

Keep fingers away from any pinch opportunities when placing or removing the Arm Pivot Rod.