Napoleon L50P2, L50N2, L50P, L38P, L38P2 User Manual

...
0 (0)

 

 

 

 

NATURAL GAS MODELS:

L38N / L50N / L38N2 / L50N2

 

ENGLISH

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

 

 

 

 

 

 

 

 

 

PROPANE GAS MODELS:

L38P / L50P / L38P2 / L50P2

FRENCH PG. 67

 

 

 

 

ADD MANUAL TITLE

INSTALLATION MANUAL

SAFETY INFORMATION

! WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

- Do not store or use gasoline or other

fl ammable vapors and liquids in the vicinity of this or any other appliance.

-WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fi re department.

-Installation and service must be performed by a qualified installer, service agency, or the supplier.

PRODUCTAcies™NAME™Series

(L38 illustrated) ADD ____ ILLUSTRATED

SAFETYBARRIER

This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certifi ed kit is used.

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

This appliance is NOT compatible with Dynamic Heat Control™

FOR INDOOR USE ONLY

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.22 AND ANSI Z21FOR.50 VEINDOORTED DECO ATIVEUSEGAS APPLIANCESONLY

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

PLACE BARCODE LABEL ON THE

OWNER’S MANUAL

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030 Phone 1 (866) 820-8686 • www.napoleonfi replaces.com • hearth@napoleonproducts.com

$10.00

W415-1707 / 07.04.17

EN safety information

! WARNING

• This appliance is hot when operated and can

 

 

DANGER

 

!

 

cause severe burns if contacted.

 

• Any changes to this appliance or its control

 

can be dangerous and are prohibited.

 

HOT GLASS WILL CAUSE

• Do not operate appliance before reading and

 

BURNS.

understanding operating instructions. Failure

 

DO NOT TOUCH GLASS UNTIL

to operate appliance according to operating

 

 

COOLED.

instructions could cause fi re or injury.

 

• Risk of fi re or asphyxiation do not operate

 

NEVER ALLOW CHILDREN TO

 

TOUCH GLASS.

appliance with glassfixed glassdoor removed.

 

 

 

A barrier designed to reduce the risk of burns from the

Do not connect 110 volts to the control valve. hot viewing glass is provided with this appliance and

shall be installed for the protection of children and other

• Risk of burns. The appliance should be turned at-risk individuals. off and cooled before servicing.

Do not install damaged, incomplete or substitute components.

Risk of cuts and abrasions. Wear protective gloves, protective footwear, and safety glasses during installation. Sheet metal edges may be sharp.

Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition.

Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children, and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

Clothing or other fl ammable material should not be placed on or near the appliance.

Due to high temperatures, the appliance should be located out of traffi c and away from furniture and draperies.

Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.

Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot surfaces. These screens and guards must be fastened to the fl oor.

Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior to operating the appliance.

The appliance is a vented gas-fi red appliance. Do not burn wood or other materials in the appliance.

The appliance area must be kept clear and free from combustible materials, gasoline and other fl ammable vapors and liquids.

Under no circumstances should this appliance be modifi ed.

This appliance must not be connected to a chimney fl ue pipe serving a separate solid fuel burning appliance.

Do not use this appliance if any part has been under water. Immediately call a qualifi ed service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

2

W415-1707 / 07.04.17

 

safety information EN

!WARNING

Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be done by a licensed or qualifi ed service person.

Do not strike or slam shut the appliance glass door.

When equipped with pressure relief doors, they must be kept closed while the appliance is operating to prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of the exhaust escaping through these openings can also cause the surrounding combustible materials to overheat and catch fi re.

Only doors / optional fronts certifi ed with the unit are to be installed on the appliance.

Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic bags, these are not toys and should be kept away from children and infants.

As with any combustion appliance, we recommend having your appliance regularly inspected and serviced as well as having a carbon monoxide detector installed in the same area to defend you and your family against carbon monoxide.

Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to decorations, a T.V. or other electronic components.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed.

If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this appliance.

Installation and repair should be done by a qualifi ed service person. The appliance should be inspected before use and at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean.

W415-1707 / 07.04.17

 

3

 

 

 

 

 

 

EN table of contents

1.0

general information

5

 

1.1

rates and efficiencies

6

 

1.2

installation overview

7

 

1.3

rating plate/lighting instruction

9

 

1.4

location

 

mobile home installation

10

 

1.5

hardware list

10

2.0

1.6

lifting handles installation/removal

10

dimensions

11

 

2.1

single-sided

11

2.2 see-thru 12

3.0minimum venting requirements 13

 

3.1

typical venting installation

15

 

3.2

minimum air terminal location

19

 

3.3

clearances

 

venting definitions & information

20

 

3.4

horizontal termination

20

4.0

3.5

vertical termination

22

rough framing

23

 

4.1

minimum framing dimensions

24

 

4.1.1

minimum clearance to combustible

5.0

 

enclosures

25

venting installation

28

 

5.1

firestop spacer assembly

28

 

5.2

horizontal installation

30

 

5.3

vertical installation

30

 

5.4

using flexible vent components

31

 

5.4.1

horizontal air terminal installation

31

 

5.5

vertical air terminal installation

32

 

5.5.1

appliance vent connection

32

6.0

5.6

vent shield installation

33

electrical information

34

 

6.1

hard wiring connection

34

 

6.2

receptacle wiring diagram

34

 

6.3

in the event of a power failure

34

 

6.4

access panel

35

 

6.5

battery back-up installation

36

7.0

6.6

wiring diagram

37

gas installation

38

8.0

operation

39

9.0

nailing tab installation

40

10.0

finish framing

41

11.0

10.1

framing with non-combustibles

41

finishing

45

 

11.1

fastener placement restriction

45

 

11.2

finishing with non-combustibles

46

 

11.3

installing non-combustible board

47

 

11.4

minimum combustible mantel

49

 

11.5

clearances

 

safety barrier installation / removal

50

 

11.6

anti condensation switch

50

 

11.7

firebox glass door installation /

50

 

11.8

removal

 

glass media installation / removal

52

 

11.9

optional media placement

52

12.0

adjustments

53

 

12.1

restricting vertical vents

53

 

12.2

venturi adjustment

53

 

12.3

pilot burner adjustment

54

13.0

12.4

flame characteristics

54

maintenance

55

 

13.1

annual maintenance

56

 

13.2

control access

56

 

13.4

burner removal

57

 

13.3

valve removal

57

 

13.5

control module removal

58

 

13.6

glass / door replacement

59

 

13.7

care of glass

59

14.0

13.8

care of plated parts

59

replacements

60

 

14.1

overview

61

15.0

14.2

burner components

62

troubleshooting

63

note:

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves the right to change or modify any information within this manual at any time without notice. Changes, other than editorial are denoted by a vertical line in the margin.

4

W415-1707 / 07.04.17

 

general information EN

Installer: please fill out appliance checklist in the owner’s manual.

1.0 general information

When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of specific recommendations from the local authority having jurisdiction, the certified high altitude input rating shall be reduced at the rate of 4% for each additional 1,000ft (305m).

Expansion / contraction noises during heating up and cooling down cycles are normal and are to be expected.

Change in flame appearance from “HI” to “LO” is more evident in natural gas than in propane.

This appliance is approved for bathroom, bedroom and bed-sitting room installations and is certified for mobile home installation.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

note:

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the appliance and must be installed.

The protective wrap on plated parts is best removed when the assembly is at room temperature but this can be improved if the assembly is warmed, using a hair dryer or similar heat source. The protective wrap must be removed before operating the appliance.

This appliance is a decorative product. It is not a source of heat and not intended to burn solid fuel.

Batteries must be disposed of according to the local laws and regulations. Some batteries may be recycled, and may be accepted for disposal at your local recycling center. Check with your municipality for recycling instructions.

W415-1707 / 07.04.17

 

5

 

 

 

 

 

 

EN general information

1.1rates and efficiencies

L38

 

Single-Sided

 

See-thru

Appliance Type

L38N

L38P

L38N2

 

L38P2

Fuel Type

Natural Gas

Propane

Natural Gas

 

Propane

Altitude (FT)

0-4,500

0-4,500

0-4,500

 

0-4,500

Max. Input (BTU/HR)

24,000

24,000

24,000

 

24,000

Min. Input (BTU/HR)

18,000

21,000

18,000

 

21,000

P4

38.5%

38.5%

38.5%

 

38.5%

L50

 

Single-Sided

See-thru

 

Appliance Type

L50N

L50P

L50N2

 

L50P2

Fuel Type

Natural Gas

Propane

Natural Gas

 

Propane

Altitude (FT)

0-4,500

0-4,500

0-4,500

 

0-4,500

Max. Input (BTU/HR)

30,000

30,000

30,000

 

30,000

Min. Input (BTU/HR)

25,000

24,000

25,000

 

24,000

P4

45.3%

45.3%

45.3%

 

45.3%

6

W415-1707 / 07.04.17

 

general information EN

1.2installation overview

12

11

8

9

5

4

7

3

6

Recommended installation steps:

1.Determine venting requirements before deciding the final location of the appliance

2.Plan out appliance enclosure, framing, fronts, accessories, etc.

3.Install rough framing (refer to “rough framing” section)

4.Place the appliance in its final position

5.Install nailing tabs (refer to “nailing tab installation” section)

6.Install appliance venting (refer to “venting installation” section)

7.Install vent shield (refer to “vent shield installation” section)

8.Install all electrical wirings (refer to “electrical information” section)

9.Install gas lines (refer to “gas installation” section)

10.Test appliance

11.Complete framing (refer to “finish framing” section)

12.Finishing (refer to “finishing” section)

13.Complete installation checklist in the owner’s manual and apply the serial number to the owner’s manual.

W415-1707 / 07.04.17

 

7

 

 

 

 

 

 

EN general information

!WARNING

Always light the pilot whether for the first time or if the gas supply has run out, with the glass door opened or removed.

Provide adequate clearance for servicing and operating the appliance.

Provide adequate ventilation.

Never obstruct the front opening of the appliance.

Objects placed in front of the appliance must be kept a minimum of 48” (121.9cm) from the front face of the appliance.

Surfaces around and especially above the appliance can become hot. Avoid contact when appliance is operating.

Fire risk. Explosion hazard.

High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at test pressures above 1/2 PSIG. Close the manual shut-off valve before pressure testing gas line at test pressures equal to or less than 1/2 PSIG (35mb).

Use only Wolf Steel approved optional accessories and replacement parts with this appliance using nonlisted accessories (blowers, doors, louvres, trims, gas components, venting components, etc.) could result in a safety hazard and will void the warranty and certification.

The appliance must not be operated at temperatures below freezing (32ºF / 0ºC). Allow the appliance to warm to above freezing prior to operation.

This appliance has been designed and certified for indoor use only.

THIS GAS APPLIANCE MUST BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local codes. Installation practices vary from region to region and it is important to know the specifi cs that apply to your area, for example in Massachusetts State:

This product must be installed by a licensed plumber or gas fi tter when installed within the commonwealth of Massachusetts.

The appliance damper must be removed or welded in the open position prior to installation of an appliance insert or gas log.

The appliance off valve must be a “T” handle gas cock.

The fl exible connector must not be longer than 36 inches (0.9m).

A carbon monoxide detector is required in all rooms containing gas fi red appliances.

The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed combustion product.

The installation must conform with local codes or, in absence of local

 

 

 

 

 

 

 

 

 

 

 

 

 

 

We suggest that our gas

codes, the National Gas and Propane Installation Code CSA B149.1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

in Canada, or the National Fuel Gas Code, ANSI Z223.1 / NFPA 54

 

 

 

 

 

 

 

 

 

 

 

 

 

 

hearth products be installed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

in the United States. Suitable for mobile home installation if installed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

and serviced by professionals

in accordance with the current standard CAN/CSA Z240MH Series,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

who are certi ed in the U.S.

for gas equipped mobile homes, in Canada or ANSI Z223.1 and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

by the National Fireplace

NFPA 54 in the United States.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The appliance and its individual shutoff valve must be disconnected

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Institute® (NFI) as NFI Gas

 

 

 

 

 

 

 

 

 

 

 

 

 

from the gas supply piping system during any pressure testing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Specialists

 

 

 

 

 

 

 

 

 

 

 

 

 

 

of that system at test pressures in excess of 1/2 psig (35 mb).

www.n certi ed.org

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (35 mb). When installed with a blower or fan, the junction box must be electrically connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI / NFPA 70 National Electric Code in the United States. In the case where the blower is equipped with a power cord, it must be connected into a properly grounded receptacle. The grounding prong must not be removed from the cord plug.

The following does not apply to inserts; as long as the required clearance to combustibles is maintained, the most desirable and benefi cial location for an appliance is in the center of a building, thereby allowing the most effi cient use of the heat created. The location of windows, doors and, the traffi c fl ow in the room where the appliance is to be located should be considered. If possible, you should choose a location where the vent will pass through the house without cutting a fl oor or roof joist. If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood fl ooring, the appliance shall be installed on a metal or wood panel extending the full width and depth, unless otherwise tested.

8

 

 

 

4.1

 

 

 

W415-1707 / 07.04.17

 

 

 

 

 

 

 

Napoleon L50P2, L50N2, L50P, L38P, L38P2 User Manual

general information EN

1.3rating plate/lighting instruction location

Both the rating plate and lighting instructions are attached to a chain located on the left side of the control area near the valve (access side). Remove the safety barrier and the control cover to gain access to the control area, refer to the “safety barrier

installation / removal” section for detailed removal instructions.

To replace, slide the instructions back into the control area and reinstall the safety barrier assembly.

access side

Rating plate

location

Pilot location

PROPANE

MODEL

MODEL

 

CERTIFIED TO CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.22-2016 AND ANSI Z21.50-2016 FOR VENTED DECORATIVE GAS FIREPLACES.

 

 

 

 

 

 

 

 

 

CERTIFIÉ SELON LES NORMES NATIONALES CANADIENNES ET AMÉRICAINES: CSA 2.22-2016 ET ANSI Z21.50-2016 POUR LES APPAREILS À GAZ VENTILÉS DÉCORATIFS.

 

 

 

 

 

 

WARNING:

CAUTION:

DIRECT VENT, VENTED GAS FIREPLACES. APPROVED FOR BEDROOM, BATHROOM AND BED-SITTING

FOYER À GAZ VENTILÉ. HOMOLOGUÉ POUR INSTALLATION DANS UNE CHAMBRE À COUCHER, UNE

 

 

 

 

 

 

ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCORDANCE

SALLE DE BAIN ET UN STUDIO. APPROPRIÉ POUR INSTALLATION DANS UNE MAISON MOBILE SI

 

 

KEE

BURNER AND CONTROL

IMPROPER INSTA LATION,

HOT WHILE OPERATING. DO NOT TOUCH.

WITH THE CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES,

 

SON INSTALLATION CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SÉRIE DE

 

 

ADJUSTM NT, A T RATION,

K P CHILDR N, CLOTHING, FURNITURE,

IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONSTRUCTION AND

 

MAISONS MOBILES ÉQUIPÉES AU GAZ, EN VIGUEUR AU CANADA OU AUX ÉTATS-UNIS DE LA

 

 

COM ARTMENT CLEAN. SEE

SERVICE OR MAINT NANCE

GASOLINE OR OTHER FLAMMABLE VAPORS

SAFETY STANDARD, TITLE 24 CFR, PART 3280. WHEN THIS US STANDARD IS NOT

 

NORME DE SÉCURITÉ ET DE CONSTRUCTION DE MAISONS MANUFACTURÉES, TITRE 24

 

 

APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME

 

CFR, SECTION 3280. DANS LE CAS OU CETTE NORME D'ÉTATS-UNIS NE PEUT ÊTRE

 

 

INSTALL TION AND O ERATING

CAN CAUSE PROP RTY DAMAG ,

AWAY.

INSTALLATIONS, SITES AND COMMUNITIES, ANSI / NFPA 501A. THIS APPLIANCE MUST BE

 

APPLIQUÉE, SE RÉFÉRER A LA NORME RELATIVE AU CRITÈRE DE MESURES DE SÉCURITÉ

 

 

PERSONA INJURY OR LOSS OF

 

INSTALLED IN ACCORDANCE WITH LOCAL CODES, IF ANY; IF NONE, FOLLOW THE CURRENT

 

CONTRE L'INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURÉS, LES

 

 

INSTRUCTIONS MANUAL.

AVERTISSEMENT:

 

 

 

IFE. REF R TO OWN R’S

ANSI Z223.1, OR CSA B149, INSTALLATION CODES. FOR USE WITH BARRIER W565-0216.

 

 

SITES ET LES COMMUNAUTÉS, ANSI/NFPA 501A. CODES. INSTALLER L’APPAREIL SELON LES

 

 

A

LIANCE NEEDS FRESH

L’APPAR IL ST CHAUD PENDANT SON

FOLLOW THE INSTALLATION INSTRUCTIONS LOCATED IN THE INSTALLATION MANUAL.

 

 

 

CODES OU RÈGLEMENTS LOCAUX, OU EN L’ABSENCE DE TELS RÈGLEMENTS, SELON LES

 

 

MANUAL. INSTA ATION AND

MANIFOLD PRESSURE: 3.5 INCHES W.C. (NG)

 

 

 

 

 

 

CODES D’INSTALLATION ANSI Z223.1 OU CSA-B149 EN VIGUER. POUR UNE UTILISER AVEC

 

 

AIR FOR SAFE O ERATION

SERVICE MUST BE P RFORM D

FONCTIONN MENT. LES ENFANTS, LES

 

 

 

 

 

 

BARRIÈRE W565-0216. SUIVEZ LES INSTRUCTIONS D'INSTALLATION SE TROUVENT DANS LE

 

 

VÉT M NTS, L S MEUBLES, L’ESSENCE ET

PRESSION AU COLLECTEUR: 3.5" D'UNE

 

 

9700539 (WSL)

 

 

 

4001657 (NGZ)

 

MANUEL D'INSTALLATION.

 

 

AND MUST BE INSTA ED

BY A QUA IFI D INSTALL R,

 

COLONNE D'EAU(GN)

 

 

 

 

 

 

 

 

AUTR S LIQUID S QUI ÉMETTENT DES GAZ

MIN SUPPLY PRESSURE: 4.5" W.C.(NG)

 

 

4001658 (NAC)

 

 

 

4001659 (WUSA)

 

MANIFOLD PRESSURE: 10 INCHES W.C.(P)

 

 

WITH ADEQUATE

ROVISIONS

SERVICE AG NCY OR THE

L38N

 

 

 

 

L38P

PRESSION AU COLLECTEUR: 10" D'UNE

 

 

VOLATILS INFLAMMABLES DOIVENT

PRESSION D'ALIMENTATION MIN: 4.5" D'UNE

CL38N

 

MODEL

CL38P

COLONNE D'EAU (P)

 

 

 

FOR COMBUSTION

GAS SUPP I R.

ÉTRE T NUS ÉLOIGNES DE L’APPAREIL.

 

COLONNE D'EAU (GN)

 

0-4500FT (0-1370m)

ALTITUDE / ÉLÉVATION

0-4500FT (0-1370m)

 

MIN SUPPLY PRESSURE: 11" W.C. (P)

 

 

 

 

MAX. SUPPLY PRESSURE: 7"* W.C. (NG)

 

24,000 BTU/h

INPUT / ALIMENTATION

24,000 BTU/h

 

PRESSION D'ALIMENTATION MIN: 11" D'UNE

 

 

AND VENTILATION AIR.

ATTENTION:

“This appliance is only for use with the type(s)

PRESSION D'ALIMENTATION MAX: 7"* D'UNE

 

18,000 BTU/h REDUCED INPUT / ALIMENTATION RÉDUITE

21,000 BTU/h

 

COLONNE D'EAU (P)

 

 

 

COLONNE D'EAU (GN)

 

 

38.5%

 

P4

 

 

38.5%

 

MAX. SUPPLY PRESSURE: 13" W.C. (P)

 

 

 

 

 

 

UN INSTA ATION OU UNE

of gas indicated on the rating plate and may

*MAXIMUM INLET PRESSURE NOT TO EXCEED 13".

 

 

 

 

 

 

 

 

 

 

 

 

*PRESSION D'ALIMENTATION MAXIMALE NE DEVAIT PAS DÉPASSER 13".

 

 

 

 

 

 

 

PRESSION D'ALIMENTATION MAX: 13" D'UNE

 

 

 

 

 

 

MODIFICATION INAPPROPRIÉE

be installed in an aftermarket, permanently

 

 

 

 

 

 

 

 

 

 

 

 

COLONNE D'EAU (P)

 

 

 

 

 

 

NOT FOR USE WITH SOLID FUEL. FOR USE WITH GLASS DOORS UN COMBUSTIBLE SOLIDE NE DOIT PAS ÊTRE UTILISÉ AVEC

 

 

 

 

 

 

DU RÉG AG , DU SERVICE T DE

located, manufactured home (USA only) or

CERTIFIED WITH THIS APPLIANCE ONLY.

 

 

 

CET APPAREIL. UTILISER AVEC LES PORTES VITRÉES

 

 

GARDEZ

BRÛLEUR ET E

’ENTRETIEN POURRAIENT ÊTRE

mobile home, where not prohibited by local

WARNING: DO NOT ADD ANY MATERIAL TO THE APPLIANCE, WHICH WILL COME IN CONTACT WITH THE FLAMES, OTHER

 

 

THAN THAT SUPPLIED BY THE MANUFACTURER WITH THE APPLIANCE.

 

 

 

 

HOMOLOGUÉES SEULEMENT AVEC CETTE APPAREIL.

 

 

 

COM ARTIMENT DES

A CAUSE DE DOMMAGES À LA

codes. See owner’s manual for details. This

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS / DÉGAGEMENTS MINIMAUX DES MATÉRIAUX COMBUSTIBLES:

 

 

CONTRÔLES

RO RES.

PROPRIETÉ DE BLESSURES

appliance is supplied with a conversion kit.”

AVERTISSEMENT: N’AJOUTEZ PAS A CET APPAREIL AUCUN MATÉRIAU DEVANT ENTRER EN CONTACT AVEC

 

 

SIDES & BACK: PER STAND OFF SPACERS FOR FRAMING AND FINISHING MATERIALS. FOR NON-COMBUSTIBLE FRAMING AND

 

 

CONSULTEZ LE MANUEL

CORPORELLES OU MÊME LA

 

FINISHING MATERIALS, SEE INSTALLATION MANUAL. DESSUS, CÔTÉS & ARRIÈRE: SELON LES ESPACEURS DE DÉGAGEMENT

LES FLAMMES AUTRE QUE CELUI QUI EST FOURNI AVEC CET APPAREIL PAR LE FABRICANT.

 

 

«Cet appareil doit être utilisé uniquement

POUR LES MATÉRIAUX D'OSSATURE SELON LA MANUEL DE PROPRIÉTAIRE POUR LES MATÉRIAUX DE FINITION.

 

 

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE NAPOLEON VENT KITS. SEE OWNERS INSTALLATION MANUAL

 

 

 

D’INFORMATION ET

MORT. CONSULTER LE MANUEL

TOP / DESSUS

0"

RECESSED DEPTH ONE SIDED/ PROFONDEUR D'ENCASTRE UNE FACE 17 15/16"

 

 

 

avec les types de gaz indiqués sur la plaque

FOR VENTING SPECIFICS. PROPER REINSTALLATION AND RESEALING IS NECESSARY AFTER SERVICING THE VENT-AIR

 

 

 

D’INSTALLATION. PAR

D’INFORMATION, L’INSTALLATION

FLOOR / PLANCHER

0" RECESSED DEPTH SEE THRU/ PROFONDEUR D'ENCASTRE TRAVERS

16 3/16"

INTAKE SYSTEM.

 

 

 

 

 

 

 

signalétique et peut être installé dans une

SIDES / CÔTÉS

0"

BACK / ARRIÈRE

 

 

0"

 

L'APPAREIL DOIT ÉVACUER SES GAZ EN UTILISANT L'ENSEMBLE D'ÉVACUATION PROPRE À NAPOLEON. RÉFÉRER AU

 

 

MESURE DE SÉCURITÉ.

ET LE SERVICE DOIVENT

VENT TOP / DESSUS DU CONDUIT D’ÉVENT

 

 

 

 

3"

 

 

 

maison préfabriquée (É.-U. seulement) ou

 

 

 

 

 

MANUEL D'INSTALLATION DE PROPRIÉTAIRE POUR L'ÉVACUATION PRÉCISE. IL EST IMPORTANT DE BIEN RÉINSTALLER ET

 

 

 

CET APPAREIL DOIT

ÊTRE EXECUTÉS PAR UN

VENT SIDES & BOTTOM / CÔTÉS ET DESSOUS DU CONDUIT D'ÉVENT

 

 

2"

 

RESCELLER L'ÉVENT APRÈS AVOIR ASSURÉ LE MAINTIEN DU SYSTÈME DE PRISE D'AIR.

 

 

 

mobile installée à demeure si les règlements

VERTICAL VENT / CONDUIT D’ÉVENT VERTICAL

 

 

 

1"

 

 

 

ÊTRE ALIMENTÉE EN AIR

MANTEL / TABLETTE

 

 

 

 

 

12" *

 

 

ELECTRICAL RATING: 115V, 60HZ. LESS THAN 12 AMPERES

 

 

INSTALLATEUR QUALIFIÉ POUR

locaux le permettent. Voir la notice de

 

* MAXIMUM HORIZONTAL EXTENSION / L'EXTENSION HORIZONTALE

MAXIMALE: 2". SEE INSTALLATION MANUAL FOR GREATER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SAMPLESPÉCIFICATIONS ÉLECTRIQUES: 115V, 60HZ. MOINS DE 12 AMPÈRE FRAIS ET AVEC SUFFISANT LE GAZ, UNE ENTREPRISE DE

 

EXTENSIONS. RÉFÉRER AU MANUEL D'INSTRUCTION POUR DES EXTENSIONS PLUS GRANDES. SEE INSTALLATION MANUAL FOR

 

 

 

 

 

 

D’AIR COMBURANTET

SERVICE OU LE FOURNISSEUR

l’utilisateur pour plus de renseignements. Une

 

MINIMUM AND MAXIMUM VENT LENGTHS. RÉFÉRER AU MANUEL D'INSTALLATION DE PROPRIÉTAIRE POUR LES LONGUEURS

DECORATIVE PRODUCT: NOT FOR USE AS A HEATING APPLIANCE

trousse de conversion est fournie avec cet

 

D'ÉVACUATION MINIMALE ET MAXIMALE.

 

 

 

 

 

 

PRODUIT DÉCORATIF: NE PAS UTILISER COMME APPAREIL DE CHAUFFAGE

 

DE VENTILATION.

DE GAZ SEULEMENT.

appareil.»

 

WOLF STEEL LTD. 24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA

SERIAL NUMBER/NO. DE SÉRIE:

L38

 

W385-2181

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FOR YOUR SAFETY:

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN VICINITY OF THIS OR ANY OTHER APPLIANCE.

CAUTION: DO NOT OPERATE THE FIREPLACE WITH THE GLASS REMOVED, CRACKED OR BROKEN.

REPLACEMENT OF THE GLASS SHOULD BE DONE BY A LICENSED OR QUALIFIED PERSON.

POUR VOTRE

SÉCURITÉ:

NE PAS ENTREPOSER NI UTILISER D’ESSENCE NI D’AUTRES VAPEURS OU LIQUIDES INFLAMMABLES DANS LE VOISINAGE DE CET APPAREIL OU DE TOUT AUTRE APPAREIL.

AVERTISSEMENT: NE PAS UTILISER L’APPAREIL SI LE PANNEAU FRONTAL EN VERRE N’EST PAS EN PLACE, EST CRAQUÉ OU BRISÉ. CONFIEZ LE REMPLACEMENT DU

PANNEAU À UN

TECHNICIEN

AGRÉÉ.

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

note:

The rating plate must remain with the appliance at all times. It must not be removed.

W415-1707 / 07.04.17

 

9

 

 

 

 

 

 

EN general information

1.4mobile home installation

This appliance must be installed in accordance with the manufacturer’s instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home Standard, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas indicated on the rating plate.

This mobile/manufactured home listed appliance comes factory equipped with a means to secure the appliance. The shipping brackets that secure the appliance to the pallet can be used to secure the appliance to the floor for mobile home installation. For mobile home installations, the appliance must be secured.

This appliance is certified to be installed in an aftermarket permanently located, manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

Conversion Kits

This appliance is field convertible between Natural Gas (NG) and Propane (P).

To convert from one gas to another, consult your Authorized dealer/distributor.

1.5hardware list

 

 

 

 

 

 

 

 

1

 

2

 

3

 

 

 

 

 

 

 

 

 

 

 

Description

Quantity

 

 

 

 

 

L38

L50

 

 

1

Hex Head Sheet Metal Screw

22

22

 

 

 

2

Round Head Sheet Metal Screw

4

4

 

 

 

3

Hex Head Sheet Metal Bolt

18

18

 

note:

Only fasteners supplied with the appliance are illustrated.

1.6lifting handles installation/removal

Type 1 (x4)

Secure the lifting handles to the side of the appliance as shown with the screws supplied. Once the appliance is in place remove the four screws each handle to the appliance. Discard the lifting handles.

note:

The lifting handles MUST be removed prior to rough framing the appliance.

10 W415-1707 / 07.04.17

2.0 dimensions EN

2.1single-sided

Base of air collar

41 3/16" 1046mm

18 5/8" 473mm

SAFETY BARRIER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

32

 

3/4"

 

 

39

 

11/16"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

832mm

 

 

 

1008mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7 1/16"

8 1/16"

 

205mm

 

179mm

 

 

 

 

 

A

 

3 1/8"

 

17 11/16"

80mm

 

 

449mm

 

 

1/2"

*

 

 

[12.7mm]

 

Ø 8"

203mm

Ø 5" 127mm

8 1/16"

205mm

B

C

 

L38

L50

A

40 3/4”

52 3/4”

(Finishing Flange)

(1035mm)

(1340mm)

B

53 5/16”

65 5/16”

 

(1354mm)

(1659mm)

C

57 5/16”

69 5/16”

 

(1456mm)

(1761mm)

*Finishing flange depth (The finishing flange defines the

 

 

perimeter of the fireplace opening. Framing or finishing materials

 

11

must NEVER encroach inside the finishing flange

W415-1707 / 07.04.17

 

EN dimensions

2.2see-thru

41 3/16" 1046mm

18 5/8"

SAFETY BARRIER

473mm

Base of air collar

39 11/16" 1008mm

32 3/4" 832mm

 

 

 

 

8 1/16"

7 1/16"

 

 

 

205mm

 

 

179mm

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 1/8"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1/2"

 

 

 

 

 

16 3/16"

 

 

 

 

 

 

 

 

 

 

80mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ø 8"

*

 

 

 

 

 

411mm

 

 

1/2"

*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[12.7mm]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

203mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[12.7mm]

Ø 5"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

127mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8 1/16"

205mm

B

C

 

 

 

 

L38

L50

 

 

 

 

A

40 3/4”

52 3/4”

 

 

 

 

(Finishing Flange)

(1035mm)

(1340mm)

 

 

 

 

B

53 5/16”

65 5/16”

 

 

 

 

 

(1354mm)

(1659mm)

 

 

 

 

C

57 5/16”

69 5/16”

 

 

 

 

 

(1456mm)

(1761mm)

 

 

 

 

*Finishing flange depth

(The finishing flange defines the perimeter of

 

 

the fireplace opening. Framing or finishing materials must NEVER

12

 

encroach inside the finishing flange

 

 

 

 

 

 

W415-1707 / 07.04.17

 

 

 

3.0 minimum venting requirements EN

!WARNING

Risk of fi re. Maintain specifi ed air space clearances to vent pipe and appliance.

If venting is included with spacers, the vent system must be supported every 3’(0.9m) for both vertical and horizontal runs. Use support ring assembly W010-0067 or equivalent non-combustible strapping to maintain the minimum clearance to combustibles for both vertical and horizontal runs. Spacers are attached to the inner pipe at predetermined intervals to maintain an even air gap to the outer pipe. This gap is required

for safe operation. A spacer is required at the start, middle, and end of each elbow to ensure this gap is maintained. These spaces must not be removed.

This appliance uses a 5” (127mm) exhaust / 8” (203.2mm) air intake vent pipe system. Refer to the section applicable to your installation.

For safe and proper operation of the appliance follow the venting instructions exactly. Deviation from the minimum vertical vent length can create difficulty in burner start-up and/or carboning. Under extreme vent configurations, allow several minutes (5-15) for the flame to stabilize after ignition. Although not a requirement, it is recommended for vent lengths that pass through unheated spaces (attics, garages, crawl spaces) be insulated with the insulation wrapped in a protective sleeve to minimize condensation.

Provide a means for visually checking the vent connection to the appliance after the appliance is installed. Use a firestop, vent pipe shield or attic insulation shield when penetrating interior walls, floor or ceiling.

The vent terminal may be painted with high temperature paint to match exterior colours. Use an outdoor paint suitable for 400°F (200°C). Application and performance of paint is the consumer’s responsibility. Spot testing is recommended. Appliance should be off.

note:

If for any reason the vent air intake system is disassembled; reinstall per the instructions provided for the initial installation.

This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing alternate constructions, such as a chimney as part of the vent system, is not permitted.

All vent measurements start at the base of the air collar of the appliance.

You may reduce the appliance from 5”/8” venting to 4”/7” venting for horizontal and vertical rise applications. Reducing must be done right off of the appliance and a new firestop spacer (W010-3440) will be required.

W415-1707 / 07.04.17 13

EN minimum venting requirements

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting components. Minimum and maximum vent lengths, for both horizontal and vertical installations, clearances from vent pipes to combustibles and air terminal locations as set out in this manual apply to all vent systems and must be adhered to. For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab, follow the installation procedure provided with the venting components. A starter adaptor must be used with the following vent systems and may be purchased from the corresponding supplier:

Vent

Starter Adapter Part

Supplier

Website

Manufacturer

Number

 

 

Duravent

W175-0170

Wolf Steel

www.duravent.com

Amerivent

5DSC-N2

American Metal

www.americanmetalproducts.com

Direct Temp

5DT-AA

Selkirk

www.selkirkcorp.com

SuperSeal

5DNA

Metal-Fab

www.mtlfab.com

For vent systems that provide seals on the inner exhaust flue, only the outer air intake joints must be sealed using a red high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent pipe joints of all other approved vent systems except for the exhaust vent pipe connection to the appliance flue collar which must be sealed using the black high temperature sealant Mill Pac.

When using Wolf Steel venting components, use only approved Wolf Steel flexible components with the wall terminal kit GD422R-2, or 1/12 to 7/12 pitch roof terminal kit GD410, 8/12 to 12/12 roof terminal kit GD411, flat roof terminal kit GD412 or periscope kit GD401 (for wall penetration below grade). With flexible venting, in conjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD420 or the 10 foot (3.1m) vent kit GD430.

For optimum flame appearance and appliance performance, keep the vent length and number of elbows to a minimum.

Horizontal runs may have a 0” (0mm) rise per foot/meter however for optimum performance it is recommended that all horizontal runs have a minimum 1/4” (21mm) rise per foot/meter using flexible venting. For safe and proper operation of the appliance, follow the venting instructions exactly.

The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that it is unobstructed and undamaged.

Rigid and flexible venting systems must not be combined. Different venting manufacturer components must not be combined.

These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of vent connections is two horizontally or three vertically (excluding the appliance and the air terminal connections) when using flexible venting.

A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings. Local codes or regulations may require different clearances.

Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼” (31.8mm) air gap all around between the inner liner and outer liner is required for safe operation.

For 4”/7” (Use reducer kit A4758AK to transition from 5”/8” to 4”/7” venting)

When using Wolf Steel 4”/7” venting components, use only approved Wolf Steel flexible components with the following termination kits: wall terminal kit GD222, GD222R, or 1/12 to 7/12 pitch roof terminal kit GD110, 8/12 to 12/12 roof terminal kit GD111, flat roof terminal kit GD112 or periscope kit GD201 (for wall penetration below grade). With flexible venting, in conjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD220 or the 10 foot (3.1m) vent kit GD330. See 4/7” vent clearance to combustibles section for specific venting parameters. See detailed instructions

14 W415-1707 / 07.04.17

minimum venting requirements EN

3.1typical venting installation

 

 

 

 

 

18"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(45.7cm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

maximum

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15"

 

 

 

 

15"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(38.1cm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(38.1cm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

minimum

 

minimum

 

 

 

 

 

 

 

 

 

base of

 

 

 

 

 

 

 

 

 

 

base of

 

 

 

 

 

47 3/4"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

air collar

 

 

 

air collar

 

 

 

 

 

 

 

 

 

 

(121.3cm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

minimum plus rise

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D

47 3/4" (121.3cm)

minimum plus rise

SINGLE-SIDED

SEE-THRU

special vent installation (periscope termination)

Use the periscope kit to locate the air termination above grade. The periscope must be installed so that when final grading is completed, the bottom air slot is located a minimum 12” (30.5cm) above grade. The maximum allowable vent length is 10’ (3m) for a fireplace and 8’ (2m) for a stove.

 

 

 

 

 

 

 

 

 

 

 

12"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(30.5cm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

minimum

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to grade

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(76.2cm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30”

 

 

 

 

 

minimum

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(76.2cm)

 

 

base of air

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

minimum

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

collar

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

base of air collar

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D

12"

(30.5cm) minimum to grade

SINGLE-SIDED

SEE-THRU

 

L38

L50

 

D

40” (101.6cm)

46 1/2” (118.1cm)

 

15

 

 

 

W415-1707 / 07.04.17

EN minimum venting requirements

SINGLE-SIDED OR SEE-THRU

16" (40.6cm) minimum

40 ft (12m) maximum 6 ft (1.83m) minimum

base of air collar

16 W415-1707 / 07.04.17

minimum venting requirements EN

4/7” vent clearance to combustibles

If necessary, 5/8” venting can be reduced to 4/7” venting.

The minimum clearances around the horizontal vent pipe to the combustible material is 1" (25.4mm) in installations with a minimum of 30” (76.2cm) vertical rise made immediately off the appliance collar and where the vent has been reduced to a 4/7" from 5/8" at the appliance.

SINGLE-SIDED

D

 

 

30" min

62 3/4"

 

(76.2cm)

 

(156.4cm)

 

 

reducer

 

 

 

base of air collar

 

SEE-THRU

reducer

D

30" min

62 3/4”

(76.2cm)

(156.4cm)

 

 

 

 

base of air collar

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L38

L50

D

40” (101.6cm)

46 1/2” (118.1cm)

W415-1707 / 07.04.17 17

EN minimum venting requirements

converting from 5/8" to 4/7" venting

1

2

X3

USE MILL PAC TO SEAL REDUCER TO THE APPLIANCE EXHAUST COLLARS.

 

 

3

4

X3

USE RED SILICONE TO SEAL REDUCER TO THE AIR INTAKE COLLARS.

 

 

5

6

X3

USE RED SILICONE TO SEAL REDUCER TO THE AIR INTAKE COLLARS.

 

 

18 W415-1707 / 07.04.17

note:
In the absence of local codes and gas supplier requirements, installation must be done in accordance to the national country requirements.

minimum venting requirements EN

3.2minimum air terminal location clearances

Covered balcony applications ††*

 

Q

S

 

 

 

 

R

 

G

P

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QMIN = 3 feet

R MAX = 2 x QACTUAL

RMAX ≤ 15 feet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(0.9m)

 

(4.6m)

 

 

INSTALLATIONS

 

 

 

 

 

 

 

 

 

CANADA

U.S.A.

 

 

 

 

 

 

 

 

A

12” (30.5cm)

12” (30.5cm)

Clearance above grade, veranda porch, deck or balcony.

 

 

 

B

12” (30.5cm)

9” (229mm)

Clearance to windows or doors that open.

 

 

 

C

12” (30.5cm)*

9” (229mm) *

Clearance to permanently closed windows.

 

 

 

D

18”

18”

Vertical clearance to ventilated soffi ts located above the terminal within a horizontal distance of 2’

 

(45.7cm)**

(45.7cm)**

(0.6m) from the center line of the terminal.

 

 

 

 

 

 

 

E

12” (30.5cm)**

12” (30.5cm)**

Clearance to unventilated soffi t.

 

 

 

F

0” (0mm)

0” (0mm)

Clearance to an outside corner wall.

 

 

 

G

0” (0mm)***

0” (0mm)***

Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).

 

2” (51mm)***

2” (51mm)***

Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).

 

 

 

H

3’(0.9m)

3’(0.9m)****

Clearance to each side of the center line extended above the meter / regulator assembly to a maxi-

 

mum vertical distance of 15’ (4.6m).

 

 

 

 

 

 

 

 

 

 

 

 

 

I

3’ (0.9m)

3’ (0.9m)****

Clearance to a service regulator vent outlet.

 

 

 

J

12” (30.5cm)

9” (229mm)

Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.

 

K

6’ (1.8m)

3’ (0.9m) †

Clearance to a mechanical air supply inlet.

 

 

 

L

7’ (2.1m) ‡

7’ (2.1m) ****

Clearance above a paved sidewalk or paved driveway located on public property.

 

 

M

12” (30.5cm)††

12” (30.5cm)****

Clearance under a veranda, porch or deck.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

N

16” (40.6cm)

16” (40.6cm)

Clearance above the roof.

 

 

 

O

2’ (0.6m)†*

2’ (0.6m) †*

Clearance from an adjacent wall including neighbouring buildings.

 

 

P

8’ (2.4m)

8’ (2.4m)

Roof must be non-combustible without openings.

 

 

 

Q

3’ (0.9m)

3’ (0.9m)

See chart for wider wall dimensions.

 

 

 

R

6’ (1.8m)

6’ (1.8m)

See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an

 

opening between the terminal and the open side of the structure.

 

 

 

 

 

 

 

 

 

 

 

S

12” (30.5cm)

12” (30.5cm)

Clearance under a covered balcony

 

 

 

The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof. * Recommended to prevent condensation on windows and thermal breakage

** It is recommended to use a heat shield and to maximize the distance to vinyl clad soffi ts.

*** The periscope requires a minimum 18 inches clearance from an inside corner.

**** This is a recommended distance. For additional requirements, check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

††Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the fl oor.

†*

Recommended to prevent recirculation of exhaust products. For additional requirements, check local codes.

††*

Permitted only if the balcony is fully open on a minimum of one side.

9.1

19

W415-1707 / 07.04.17

EN minimum venting requirements

3.3horizontal termination

L38 / L50

40’

V+H ≤ 40 ft.

38’ 6”

H ≤ 20 ft.

 

 

V + H are measured from the centre of vent

 

elbows. Elbows are considered as 90º.

 

Two 45º elbows = One 90º elbow.

30’ 1-6 elbow zone 1-5 elbow zone

1-4 elbow zone

1-3 elbow zone 1-2 elbow zone

1 elbow zone

V20’

15’

 

10’

 

 

 

 

 

 

5’

 

 

 

 

 

 

1.25’ (15”)

 

 

 

 

 

 

0’

5’

10’

15’

20’

25’

 

1.5’

 

3.875’

 

H

 

 

 

(18”)

(46”)

 

 

 

 

0’

 

 

 

 

 

20

W415-1707 / 07.04.17

 

 

 

 

 

Loading...
+ 46 hidden pages