Multiquip MC3PEA, MC3SEA User Manual

0 (0)

OPERATION AND PARTS MANUAL

MIX N' GO

MODELS MC3SEA, MC3SBA (B&S) MINI CONCRETE STEEL DRUM MIXERS

MODELS MC3PEA, MC3PBA (B&S) MINI CONCRETE PLASTIC DRUM MIXERS

EFFECTIVE S/N 230502698

Revision #3 (09/20/11)

To find the latest revision of this publication, visit our website at: www.multiquip.com

THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.

PROPOSITION 65WARNING

Engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drillingandotherconstructionactivities contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Some examples of these chemicals are:

Leadfromlead-basedpaints.

Crystallinesilicafrombricks.

Cementandothermasonryproducts. Arsenicandchromiumfromchemically treatedlumber.

Your risk from these exposures varies, dependingonhowoftenyoudothistype of work. To reduce your exposure to these chemicals: ALWAYS work in a well ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

PAGE 2 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11)

SILICOSIS/RESPIRATORWARNINGS

WARNING

SILICOSIS WARNING

Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. In addition, California and some other authorities have listed respirable crystalline silica as a substance known to cause cancer. When cutting such materials, always follow the respiratory precautions mentioned above.

WARNING

RESPIRATORY HAZARDS

Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm. If you are unfamiliar with the risks associated with the particular process and/or material being cut or the composition of the tool being used, review the material safety data sheet and/or consult your employer, the material manufacturer/supplier, governmental agencies such as OSHA and NIOSH and other sources on hazardous materials. California and some other authorities, for instance, have published lists of substances known to cause cancer, reproductive toxicity, or other harmful effects.

Control dust, mist and fumes at the source where possible. In this regard use good work practices and follow the recommendations of the manufacturers or suppliers, OSHA/NIOSH, and occupational and trade associations. Water should be used for dust suppression when wet cutting is feasible. When the hazards from inhalation of dust, mists and fumes cannot be eliminated, the operator and any bystanders should always wear a respirator approved by NIOSH/MSHA for the materials being used.

MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 3

TABLE OF CONTENTS

Multiquip Mix N' Go —

Portable Concrete Mixer

Proposition 65 Warning .............................................

2

Silicosis/Respiratory Warnings ..................................

3

Table of Contents ......................................................

4

Parts Ordering Procedures .......................................

5

Safety Information ................................................

6-10

Operation and Safety Decals .............................

11-12

Specifications ..........................................................

13

Dimensions (Mixer) .................................................

14

Dimensions (Electric Motor)....................................

15

General Information ................................................

16

Mixer Components..................................................

17

Basic Engine ...........................................................

18

Assembly Instructions ........................................

19-20

Pre-Inspection (Gasoline Engine) ...........................

21

Initial Start-up (Electric Motor) ................................

22

Initial Start-up (Gasoline Engine).......................

23-24

Maintenance ......................................................

25-27

Preparation for Long-Term Storage ........................

28

Troubleshooting (Engine) ........................................

30

Troubleshooting (Engine/Mixer) ..............................

31

Explanation Of Code In Remarks Column ..............

32

Suggested Spare Parts ...........................................

33

Nameplate and Decals.......................................

34-35

Mixer Assembly (Steel Drum) ............................

36-39

Mixer Assembly (Plastic Drum) ..........................

40-43

Terms and Conditions of Sale .................................

44

Specification and part number are subject to change without notice.

PAGE 4 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11)

www.multiquip.com

PARTS ORDERING PROCEDURES

 

 

 

 

 

 

Ordering parts has never been easier!

 

 

 

 

 

 

 

Choose from three easy options:

 

 

 

 

 

 

 

 

 

 

 

 

Effective:

 

 

 

 

 

 

 

 

 

 

 

 

January 1st, 2006

Best Deal! Order via Internet (Dealers Only):

 

 

If you have an MQ Account, to obtain a Username

 

 

 

Order parts on-line using Multiquip’s SmartEquip website!

 

 

 

 

 

 

 

and Password, E-mail us at: parts@multiquip.

 

 

 

 

N View Parts Diagrams

 

 

com.

 

 

 

 

N Order Parts

 

 

To obtain an MQ Account, contact your

 

 

 

 

N Print Specification Information

 

 

District Sales Manager for more information.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Goto www.multiquip.com and click on

 

 

Use the internet and qualify for a 5% Discount

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

on Standard orders for all orders which include

 

 

 

 

 

 

Order

Parts

to log in and save!

 

 

 

 

 

 

 

 

 

 

 

 

complete part numbers.*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note: Discounts Are Subject To Change

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Order via Fax (Dealers Only):

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fax your order in and qualify for a 2% Discount

 

 

 

 

 

 

 

All customers are welcome to order parts via Fax.

 

on Standard orders for all orders which include

 

 

 

 

 

 

 

 

 

 

 

 

 

Domestic (US) Customers dial:

 

complete part numbers.*

 

 

 

 

 

 

1-800-6-PARTS-7 (800-672-7877)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note: Discounts Are Subject To Change

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Order via Phone: Domestic (US) Dealers Call:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1-800-427-1244

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Non-Dealer Customers:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

International Customers should contact

 

 

 

Contact your local Multiquip Dealer for

 

 

 

 

 

 

 

 

 

their local Multiquip Representatives for

 

 

 

parts or call 800-427-1244 for help in

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Parts Ordering information.

 

 

 

locating a dealer near you.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When ordering parts, please supply:

R

Dealer Account Number

R Specify Preferred Method of Shipment:

R

Dealer Name and Address

UPS/Fed Ex

DHL

R

Shipping Address (if different than billing address)

N Priority One

Truck

R

Return Fax Number

N Ground

 

N Next Day

 

R

Applicable Model Number

 

N Second/Third Day

 

 

 

 

RQuantity, Part Number and Description of Each Part

NOTICE

All orders are treated as Standard Orders and will ship the same day if received prior to 3PM PST.

WE ACCEPT ALL MAJOR CREDIT CARDS!

MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 5

Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment.

Failure to read and understand the safety messages and operating instructions could

result in injury to yourself and others.

SAFETY MESSAGES

The four safety messages shown below will inform you about potential hazards that could injure you or others.The safety messages specifically address the level of exposure to the operator and are preceded by one of four words:

DANGER,WARNING, CAUTION or NOTICE.

SAFETY SYMBOLS

DANGER

Indicates a hazardous situation which, if not avoided,

WILL result in DEATH or SERIOUS INJURY.

WARNING

Indicates a hazardous situation which, if not avoided,

COULD result in DEATH or SERIOUS INJURY.

CAUTION

Indicates a hazardous situation which, if not avoided,

COULD result in MINOR or MODERATE INJURY.

NOTICE

Addresses practices not related to personal injury.

SAFETY INFORMATION

Potential hazards associated with the operation of this equipment will be referenced with hazard symbols which may appear throughout this manual in conjunction with safety messages.

Symbol

Safety Hazard

Lethal exhaust gas hazards

Explosive fuel hazards

Burn hazards

Rotating parts hazards

PAGE 6 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11)

GENERAL SAFETY

CAUTION

NEVER operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job or city and state regulations.

Avoid wearing jewelry or loose fitting clothes that may snag on the controls or moving parts as this can cause serious injury.

NEVER operate this equipment when not feeling well due to fatigue, illness or when under medication.

NEVER operate this equipment under the influence of drugs or alcohol.

ALWAYS clear the work area of any debris, tools, etc. that would constitute a hazard while the equipment is in operation.

ALWAYS check the equipment for loosened threads or bolts before starting.

DO NOT use the equipment for any purpose other than its intended purposes or applications.

SAFETY INFORMATION

NOTICE

This equipment should only be operated by trained and qualified personnel 18 years of age and older.

Whenever necessary, replace nameplate, operation and safety decals when they become difficult read.

Manufacturer does not assume responsibility for any accident due to equipment modifications. Unauthorized equipment modification will void all warranties.

NEVER use accessories or attachments that are not recommended by Multiquip for this equipment. Damage to the equipment and/or injury to user may result.

ALWAYS know the location of the nearest

fire extinguisher.

ALWAYS know the location of the nearest

first aid kit.

ALWAYS know the location of the nearest phone or keep a phone on the job site. Also, know the phone numbers of the nearest ambulance, doctor and fire department.

This information will be invaluable in the case of an emergency.

MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 7

DANGEROUS
GAS FUMES

MIXER SAFETY

DANGER

NEVER operate the equipment in an explosive atmosphere or near combustible materials.An explosion or fire could result causing severe bodily harm or even death.

DO NOT mix flammable or explosive substances.

WARNING

NEVER place your hands inside the drum while starting or operating this equipment.

NEVER disconnect any emergency or safety devices. These devices are

intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death. Disconnection of any of these devices will void all warranties.

Before operating mixer, ensure that safety grate is in position and correctly fitted.

CAUTION

NEVER lubricate components or attempt service on a running machine.

NOTICE

ALWAYS keep the machine in proper running condition.

ALWAYS ensure mixer is on level ground before mixing.

Fix damage to machine and replace any broken parts immediately.

DO NOT tip mixer onto drum mouth when the drum is rotating.

Ensure the drum is rotating while filling and emptying the drum.

ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.

SAFETY INFORMATION

ENGINE SAFETY (GASOLINE MODELS ONLY)

DANGER

Engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled.

The engine of this equipment requires an adequate free flow of cooling air. NEVER operate this equipment in any enclosed or narrow

area where free flow of the air is restricted. If the air

flow is restricted it will cause injury to people and property and serious damage to the equipment or engine.

WARNING

DO NOT place hands or fingers inside engine compartment when engine is running.

NEVER operate the engine with heat shields or guards removed.

Keep fingers, hands hair and clothing away

from all moving parts to prevent injury.

DO NOT remove the engine oil drain plug

while the engine is hot. Hot oil will gush out of the oil tank and severely scald any persons in the general area of the mixer.

CAUTION

NEVER touch the hot exhaust manifold, muffler or cylinder. Allow these parts to cool

before servicing equipment.

Make certain the operator knows how to and is capable of turning the engine OFF in case of an emergency.

NOTICE

NEVER run engine without an air filter or with a dirty air filter. Severe engine damage may occur. Service air filter frequently to prevent engine malfunction.

NEVER tamper with the factory settings of the engine or engine governor. Damage to the engine or equipment can result

if operating in speed ranges above the maximum allowable.

PAGE 8 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11)

FUEL SAFETY (GASOLINE MODELS ONLY)

DANGER

DO NOT add fuel to equipment if it is placed inside truck bed with plastic liner. Possibility exists of explosion or fire due to static electricity.

FUEL

FUEL

DO NOT start the engine near spilled fuel or combustible fluids. Fuel is extremely flammable and its vapors can cause an explosion if ignited.

ALWAYS refuel in a well-ventilated area, away from sparks and open flames.

ALWAYS use extreme caution when working with

flammable liquids.

DO NOT fill the fuel tank while the engine is running or hot.

DO NOT overfill tank, since spilled fuel could ignite if it comes into contact with hot engine parts or sparks from the ignition system.

Store fuel in appropriate containers, in well-ventilated areas and away from sparks and flames.

NEVER use fuel as a cleaning agent.

DO NOT smoke around or near the equipment. Fire or explosion could result from fuel vapors or if fuel is spilled on a hot engine.

SAFETY INFORMATION

GENERATOR SAFETY

If using a generator to power mixer, refer to applicable generator manual safety information section.

ELECTRIC MOTOR SAFETY (ELECTRIC MODELS ONLY)

NOTICE

Operate electric motor only at the specified voltage indicated on the nameplate.

DO NOT spray water onto electric motor.

ALWAYS disconnect AC power plug from power source before moving mixer.

ALWAYS make sure the ON/OFF switch on the electric motor is in the OFF position when not in use and before inserting the mixer’s power plug into an AC receptacle.

Power Cord/Cable Safety

DANGER

NEVER let power cords or cables lay in water.

NEVER use damaged or worn cables or cords when connecting equipment to generator. Inspect for cuts in the insulation.

NEVER grab or touch a live power cord or cable with wet hands. The possibility exists of electrical shock, electrocution or death.

Make sure power cables are securely connected. Incorrect connections may cause electrical shock and damage to the mixer.

CAUTION

Ensure that cables and cords will not be tripped over or trapped underneath the mixer.

NOTICE

ALWAYS make certain that proper power or extension cord has been selected for the job.

MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 9

SAFETY INFORMATION

TRANSPORTING SAFETY

CAUTION

NEVER allow any person or animal to stand underneath the equipment while lifting.

NOTICE

ALWAYS make sure forklift forks are inserted into pockets (if applicable) as far as possible when lifting the mixer.

ALWAYS shutdown engine before transporting.

NEVER lift the equipment while the engine is running.

Tighten fuel tank cap securely and close fuel cock to prevent fuel from spilling.

DO NOT lift machine to unnecessary heights.

ALWAYS tie down equipment during transport by securing the equipment with rope.

NEVER tip the engine to extreme angles during lifting as it may cause oil to gravitate into the cylinder head, making the engine start difficult.

ENVIRONMENTAL SAFETY

NOTICE

Dispose of hazardous waste properly. Examples of potentially hazardous waste are used motor oil, fuel and fuel filters.

DO NOT use food or plastic containers to dispose of hazardous waste.

DO NOT pour waste, oil or fuel directly onto the ground, down a drain or into any water source.

PAGE 10 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11)

Multiquip MC3PEA, MC3SEA User Manual

OPERATION AND SAFETY DECALS

Machine Safety Decals

The Mix N' Go mixer is equipped with a number of safety decals.These decals are provided for operator safety and maintenance information.The illustration below and on the next page shows these decals as they appear on the machine. Should any of these decals become unreadable, replacements can be obtained from your dealer.

WARNING!

ALARMA!

AVERTISSEMENT!

ENGLISH - WARNING! TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND INSTRUCTION MANUAL

ESPAÑOL - ATENCION! PARA REDUCIR EL RIESGO DEL LESIONES EL USUARIO DEBE LEER Y ENTENDER EL MANUAL DE INSTRUCCIONES FRANÇAIS - ATTENTION! AFIN DE DIMINUER LE RISQUE DE BLESSURES L’UTILISATEUR DOIT LIRE ET COMPRENDRE CE MANUEL D’ INSTRUCTIONS

DCL251

P/N: DCL251

P/N: 510165

MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 11

OPERATION AND SAFETY DECALS

 

WARNING!

 

ADVERTENCIA!

AVERTISSEMENT!

1. Read owner’s manual before operating mixer.

1. Lea el manual de operació antes de usar la mezcladora.

1. Lisez le manual d’ utilisation avant d’ utiliser le le malaxeur.

2. Keep unauthorized and untrained people away

2. Mantenga personas que no estén autorizadas o capacitadas

2. Seul un personnel qualifié peut être authorisé à se trouver à proximité

 

from mixer during operation.

 

 

 

 

alejades de la mezcladora durante el funcionamiento de la

du malaxeur quand il est en opération.

 

 

 

3. Make sure all safety devices (guards) are in place

máquina.

 

 

 

 

 

3. Assurez vous que tous les dispositifs de sécurité sont en place avant

 

before mixer is started.

 

 

 

 

3. Asegúreseque todos los aparatos de seguridad estén

de mettre le malaxeur en marche.

 

 

 

 

 

4. Keep hands and fingers away from moving objects.

trabajando apropiadamente antes de usar la mezcladora.

4. Gardez les mains et doigts loin de toute piè en mouvement.

5. NEVER leave mixer unattended when operating.

4. Mantenga las monos y dedos alejados de objetos en moviminto.

5. NE LAISSEZ jamais le malaxeur sans surveillance quand il est en

5. NUNCA se aleje de la mezclaora mientras ésta, este trabajando!

6. ALWAYS check V-belt before starting mixer.

 

 

opération.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6. SIEMPRE inspeccione la banda antes de encender la mezcladora.

6. VEUILLEZ toujours vérifier la courroie avant de mettre le malaxeur

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

en marche.

 

 

 

 

 

 

 

 

GASOLINE ENGINE

 

 

 

MÁQUINAS DE GASOLINA

 

 

 

 

MOTEUR À ESSENCE

 

 

 

 

Make sure engine is turned off and spark plug wire is

Asegure que la máquina este apagada y el alambre de la bujía

Assurez vous que le moteur est arrêté et que le fil de la bougie est

 

disconnected before cleaning mixer.

 

 

este desconectado antes de empezar a limpiar la mezcladora.

débranché avant de nettoyer le malaxeur.

 

 

 

 

DO NOT operate mixer in an enclosed area, proper

NO encienda la mezcladora en una área cerrada; es necesario

N’ UTILISEZ pas le malaxeur dans un endroit fermé, il est nécessaire

 

ventilation is required.

 

 

 

 

estar en una área que tenga apropiada ventilación.

de travailler dans un endroit avec une bonne aération.

 

ALWAYS stop the engine and allow engine to cool before

SIEMPRE apague la máquina y permita que se enfrie antes de

VEUILLEZ toujours vé la courroie avant de mettre le malaxeur en

 

adding fuel or oil.

 

 

 

 

ponerle gasolina o aceite.

 

 

 

marche.

 

 

 

 

 

 

 

ALWAYS check fuel, oil and air filter before starting engine.

SIEMPRE revise la gasolina, aceite, y el filtro del air antes de

VÉRIFIEZ toujours le niveau d’essence et d’huile ainsi que le filtre à

 

 

 

 

 

 

 

 

encender la máquina.

 

 

 

air avant de mettre le moteur en marche.

 

 

 

 

 

ELECTRIC MOTOR

 

 

 

 

MOTOR ELÉCTRICO

 

 

 

 

MOTEUR ÉLECTRIQUE

 

 

 

 

Make sure power cord has been disconnected from power

Asegúrese que el cable de corriente esté de empezar a limpiar

Assures vous toujours que le cable a été débranché de la prise de

 

source before cleaning mixer.

 

 

la mezcladora.

 

 

 

 

 

courant avant de nettoyer le malaxeur.

 

 

 

 

This electric motor is for 115 VAC operation only.

Este motor elétrico está solamente capacitado para corriente

Ce moteur électrique à été conçu pour opération à 115 volts seulement.

 

alterna de 115 voltios.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ALWAYS use an extension cord of proper size, see chart

SIEMPRE use el tamaño de extensiones de alambre indicado

Il faut toujours utiliser une rallonge de taille appropriée, veuillez s’il vous

 

below:

 

 

 

 

 

 

como muestra el diagrama abajo:

 

 

 

référer au diagramme suivant:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXTENSION CORD SIZE

 

 

 

TAMAÑO DE EXTENSIÓN

 

 

TAILLE DE LA RALLONGE

 

 

 

 

No. 12 Wire

No. 10 Wire

 

No. 8 Wire

 

No. 6 Wire

 

 

Alambre

Alambre

 

Alambre

Alambre

 

 

Cable

Cable

Cable

 

Cable

 

 

 

 

 

 

Numéro 12

Numéro 10

 

Numéro 8

Numéro 6

 

 

Numéro 12

Numéro 10

Numéro 8

 

Numéro 6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

50 feet

75 feet

 

100 feet

 

200 feet

 

 

50 pies

75 pies

 

100 pies

200 pies

 

 

50 pieds

50 pieds

50 pieds

 

50 pieds

 

 

(15.24 meters)

(22.86 meters)

 

(30.48 meters)

 

(60.96 meters)

 

 

(15.24 metros)

(22.86 metros)

 

(30.48 metros)

(60.96 metros)

 

 

(15.24 métres)

(15.24 métres)

(15.24 métres)

(15.24 métres)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ELECTRIC

MOTOR

MOTOR

ELÉCTRICO

MOTEUR ÉLECTRIQUE

REMOVE BOLT AND FILL WITH EP. 90 GEAR OIL

REMOVER EL TORÑILLO Y LLENAR CON ACEITE DE ENGRNAJE EP. 90

ÔTEZ LE BOULON ET REMPLISSEZ AVEC DE I’HUILE EP. 90 À ENGRENAGES

CHECK DAILY

REVISAR DIARIO

VÉRIFIEZ QUOTIDIENNEMENT

 

 

 

 

 

 

 

 

 

 

NEVER! OPERATE MIXER WITH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ELECTRIC

V-BELT COVER REMOVED.

 

 

 

 

 

 

 

 

 

MOTOR

NUNCA! MANEJE LA MEZCLADORA

 

 

 

 

 

 

 

 

 

MOTOR

 

 

 

 

 

 

 

 

 

SIN LA COBERTURA DE BANDA-V

 

 

 

 

 

 

 

 

 

ELÉCTRICO

REMOVIDA.

 

 

 

 

 

 

 

 

 

MOTEUR

N’ UTILISEZ! JAMAIS LE MALAXEUR

 

 

 

 

 

 

 

 

 

ÉLECTRIQUE

SANS LE COUVERCLE DE LA COURROIE.

 

 

 

 

 

 

 

 

 

 

DCL250

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P/N DCL250

PAGE 12 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11)

MIX N' GO MIXER — SPECIFICATIONS

Table 1. Specifications (Engine & Electric Motor)

 

Model

BRIGGS & STRATTON 91200

BALDOR 17LYE304

 

 

 

 

 

Type

4-stroke, Vertical valve, Single

3/4 HP, 120 VAC, Single

 

Cylinder

Phase Electric Motor

 

 

 

 

 

 

 

 

Bore X Stroke

2.56 in. x 1.75 in.

N/A

 

 

(65.1 mm x 44.4 mm)

 

 

 

 

 

 

 

 

 

 

 

Displacement

9.0 cu. in. (148 cc)

N/A

 

 

 

 

 

 

 

Max Output

3.5 HP at 3,600 R.P.M.

3/4 H.P./3,450

RPM

Engine/Electric Motor

 

 

 

 

Standard Idle Speed

1,800 ± 100 R.P.M.

N/A

 

 

 

 

 

 

 

Fuel Tank Capacity

Approx. 0.5 U.S. Gallons

N/A

 

 

(1.89 Liters)

 

 

 

 

 

 

 

 

 

 

 

Fuel

Unleaded Gasoline

N/A

 

 

 

 

 

 

 

Lube Oil Capacity

2 U.S. Quarts (1.89 Liters)

N/A

 

 

 

 

 

 

 

Speed Control Method

Centrifugal Fly-weight Type

N/A

 

 

 

 

 

 

 

Starting Method

Recoil Start

N/A

 

 

 

 

 

Dimensions (L x W x H)

12.5 x 11.47 x 12.18 in.

11.75 x 6.0 X 8.0 in.

(317.5 x 291.4 x 309.4 mm)

(298 X 152 X 203 mm)

 

 

 

 

 

 

 

Dry Net Weight

20.3 lbs (9.2 kg)

Approx. 12 lbs.

(5.4 Kg.)

 

 

 

 

 

Table 2. Mix N' Go Mixer Specifications

Height

34 in. (863.6 mm)

 

 

Width

23-5/8 in. (584.2 mm)

 

 

Length

48-1/2 in. (1,219.2 mm)

 

 

Stand Weight

35 lbs. (15.9 Kg)

 

 

Maximum Drum Capacity

4.5 cu. ft. (0.13 m3)

 

 

Maximum Mixing Capacity (1/2 bag)

3.0 cu. ft. (0.08 m3)

 

 

Unladen Weight - Electric Motor

129 lbs. (58.5 Kg)

 

 

Unladen Weight - Gasoline Engine

138 lbs. (62.6 Kg)

 

 

MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 13

MIX N' GO MIXER — DIMENSIONS (MIXER)

PAGE 14 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11)

Loading...
+ 32 hidden pages