BLUETOOTH 11:00PM
Song Title
Artist
Album
23/25
3:08
MUTE |
MENU |
SOURCE
AWMC3 ALL-WEATHER MEDIA CONTROLLER WITH 3" DISPLAY OWNER’S MANUAL
M T X . C O M
IMPORTANT NOTICE
If you have any questions regarding wire routing in a vehicle, please contact MTX Technical Support at 1-800-225-5689.
When connecting power and ground wires ensure that the red power wire is fused at the point where it is connected to the vehicle’s battery. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the product.
PRODUCT INFORMATION
Model #
Serial #
Dealer’s Name
Date of Purchase
IN THE BOX
•All-Weather Media Controller
•Mounting Plate
•U-Shape Mounting Bracket
•(4) M3.5 x 30MM Machine Screws
•(4) M4 Hex Nuts
INTRODUCTION
Thank you for purchasing this MTX Audio all-weather media controller that is designed to work with most Bluetooth® enabled devices including iPhone® and Android® smartphones and tablets. This easy to install and use head unit is capable of transforming your Bluetooth® enabled mobile device into the center of your vehicle’s audio system. Congratulations and enjoy the ultimate audio experience with MTX!
FEATURES
•3" Full Color TFT Display
•SiriusXM-Ready™ (SiriusXM Connect Vehicle Tuner and Subscription Sold Separately)
•AM / FM / WB Tuner
•Bluetooth® Audio Streaming
•Internal 4 x 50 Watt Power Amplifier
•AUX Input
•USB Charging
•iPhone® - Unit Will Charge and Play Music Through USB*
•Android® - Unit Will Charge, but Will Not Play Music Through USB
•Unit Will Play Music and Display Album Artwork Using a USB Memory Stick (.mp3)
•Weather Resistant (IP66)
•Selectable EQ
•2 Sets of Preouts (Front / Rear)
•Backlit Control Buttons
*Made for iPhone 5s, iPhone SE, iPhone 6, iPhone 6 Plus, iPhone 6s, iPhone 6s Plus, iPhone 7, iPhone 7 Plus
2 |
M T X . C O M |
|
|
WIRE CONNECTION
20A
Power / Speaker Connector
SXM
(SiriusXM Connect Tuner Sold Separately)
Black
AUX In
Grey
Line Out (Front)
Brown
Line Out (Rear)
Antenna
DIN
USB
POWER AND SPEAKER CONNECTION
|
|
|
|
3 |
2 |
1 |
|
|
|
|
|
6 |
5 |
4 |
|
|
|
|
|
||||
|
|
|
|
||||
|
|
|
|
||||
|
|
|
|
9 |
8 |
7 |
|
|
|
|
|
||||
|
|
|
|
||||
|
|
|
|
||||
|
|
r |
12 |
11 |
10 |
||
|
|
|
|
|
|
||
Pin # |
|
Wire Color |
|
|
Wire Definition |
||
|
|
|
|
|
|
||
11 |
|
White / Black |
|
|
Front Left Speaker (-) |
||
12 |
|
White |
|
|
Front Left Speaker (+) |
||
6 |
|
Green / Black |
|
|
Rear Left Speaker (-) |
||
1 |
|
Green |
|
|
Rear Left Speaker (+) |
||
5 |
|
Grey |
|
|
Front Right Speaker (+) |
||
4 |
|
Grey / Black |
|
|
Front Right Speaker (-) |
||
9 |
|
Purple |
|
|
Rear Right Speaker (+) |
||
8 |
|
Purple / Black |
|
|
Rear Right Speaker (-) |
||
|
|
|
|
|
|
||
2 |
|
Blue |
|
|
Remote Output |
||
|
|
|
|
|
|
|
|
7 |
|
|
|
|
|
|
|
|
|
|
|
|
|
||
10 |
|
Yellow |
|
|
Battery (Fuse 20A) |
||
|
|
|
|
|
|
||
3 |
|
Black |
|
|
Ground |
||
|
|
|
|
|
|
|
|
3 |
2 |
1 |
6 |
5 |
4 |
9 |
8 |
7 |
12 |
11 |
10 |
M T X . C O M |
3 |
|
|
INSTALLATION
Mounting (Using Mounting Plate)
To mount the unit, find a flat surface with adequate clearance behind it that provides enough room for the unit and all it’s necessary wiring.
•Once a mounting location has been determined, cut a circular hole 3" (77mm) in diameter.
•After the hole is cut, slide the unit and wiring through the hole. A piece of self adhesive EVA foam is supplied in order to create a water resistant seal. This may be placed on the back side of the unit if desired.
•Slide the mounting plate over the backside of the unit and secure with the supplied screws.
•Press on the trim bezel to the front side of the unit.
•Plug in all wiring harnesses and cables. Refer to the wiring diagram for wire harness connection
types.
Mounting Plate
Source Unit
Panel
Mounting Screws
Trim Bezel
Mounting (Using U Shape Bracket)
To mount the unit, find a flat surface with adequate clearance behind it that provides enough room for the unit and all it’s necessary wiring.
•Once a mounting location has been determined, cut a circular hole 3" (77mm) in diameter.
•After the hole is cut, slide the unit and wiring through the hole. A piece of self adhesive EVA foam is supplied in order to create a water resistant seal. This may be placed on the back side of the unit if desired.
•Slide the U bracket over the two studs on the back of the unit. Tighten down with supplied nuts.
•Press on the trim bezel to the front side of the unit.
•Plug in all wiring harnesses and cables. Refer to the wiring diagram for wire harness connection types.
Trim Bezel
Nuts
U Shape Bracket
Panel
Source Unit
4 |
M T X . C O M |
|
|
INSTALLATION
Mounting (Using Optional Vehicle Specific Dash Mount Kit - Sold Separately)
The unit will be mounted to each vehicle differently. Make sure to following the vehicle specific directions that were included with the dash kit.
•Slide the two included speed clips onto the rear of the dash kit.
•The dash kit may include additional space to mount rocker panel switches for accessories. On the rear of the dash kit, grooves will be provided to give proper location and size for mounting additional switches.
•Before mounting the source unit to the dash kit, make sure that the trim bezel that is included with the source unit is NOT attached. If it is attached, it will need to be removed. It will NOT be used.
•Attach the source unit to the rear of the dash kit using the included nuts.
|
|
|
|
|
|
|
|
Source Unit |
Nuts |
||
|
|
Dash Kit
Mounting Screws
Source Unit
Nuts
Speed Clips
M T X . C O M |
5 |
|
|