Thank you for purchasing the MSI® B365M PRO-VDH motherboard. This User Guide gives information about board layout, component overview, BIOS setup and software installation.
Contents |
|
Safety Information........................................................................................... |
2 |
Specifications................................................................................................... |
3 |
Rear I/O Panel.................................................................................................. |
6 |
LAN Port LED Status Table................................................................................. |
6 |
Overview of Components ................................................................................ |
7 |
DIMM Slots.......................................................................................................... |
8 |
CPU Socket ......................................................................................................... |
9 |
PCI_E1~3: PCIe Expansion Slots ...................................................................... |
10 |
JRGB1: RGB LED connector ............................................................................. |
10 |
JFP1, JFP2: Front Panel Connectors ............................................................... |
11 |
SATA1~6: SATA 6Gb/s Connectors.................................................................... |
11 |
M2_1: M.2 Slot (Key M) ..................................................................................... |
12 |
ATX_PWR1, CPU_PWR1: Power Connectors.................................................... |
12 |
JUSB1, JUSB2: USB 2.0 Connectors ................................................................ |
13 |
JUSB3, JUSB4: USB 3.1 Gen1 Connectors....................................................... |
13 |
JAUD1: Front Audio Connector......................................................................... |
14 |
JCOM1: Serial Port Connector ......................................................................... |
14 |
JLPT1: Parallel Port Connector........................................................................ |
14 |
CPU_FAN1, SYS_FAN1~2: Fan Connectors...................................................... |
15 |
JTPM1: TPM Module Connector ....................................................................... |
16 |
EZ Debug LED ................................................................................................... |
16 |
JCI1: Chassis Intrusion Connector................................................................... |
17 |
JBAT1: Clear CMOS (Reset BIOS) Jumper ....................................................... |
17 |
BIOS Setup..................................................................................................... |
18 |
Entering BIOS Setup ......................................................................................... |
18 |
Resetting BIOS.................................................................................................. |
19 |
Updating BIOS................................................................................................... |
19 |
Installing OS, Drivers & Utilities ................................................................... |
20 |
Installing Windows® 10 ..................................................................................... |
20 |
Installing Drivers .............................................................................................. |
20 |
Installing Utilities.............................................................................................. |
20 |
Contents 1
Safety Information
yThe components included in this package are prone to damage from electrostatic discharge (ESD). Please adhere to the following instructions to ensure successful computer assembly.
yEnsure that all components are securely connected. Loose connections may cause the computer to not recognize a component or fail to start.
yHold the motherboard by the edges to avoid touching sensitive components.
yIt is recommended to wear an electrostatic discharge (ESD) wrist strap when handling the motherboard to prevent electrostatic damage. If an ESD wrist strap is not available, discharge yourself of static electricity by touching another metal object before handling the motherboard.
yStore the motherboard in an electrostatic shielding container or on an anti-static pad whenever the motherboard is not installed.
yBefore turning on the computer, ensure that there are no loose screws or metal components on the motherboard or anywhere within the computer case.
yDo not boot the computer before installation is completed. This could cause permanent damage to the components as well as injury to the user.
yIf you need help during any installation step, please consult a certified computer technician.
yAlways turn off the power supply and unplug the power cord from the power outlet before installing or removing any computer component.
yKeep this user guide for future reference.
yKeep this motherboard away from humidity.
yMake sure that your electrical outlet provides the same voltage as is indicated on the PSU, before connecting the PSU to the electrical outlet.
yPlace the power cord such a way that people can not step on it. Do not place anything over the power cord.
yAll cautions and warnings on the motherboard should be noted.
yIf any of the following situations arises, get the motherboard checked by service personnel:
Liquid has penetrated into the computer.
The motherboard has been exposed to moisture.
The motherboard does not work well or you can not get it work according to user guide.
The motherboard has been dropped and damaged.
The motherboard has obvious sign of breakage.
yDo not leave this motherboard in an environment above 60°C (140°F), it may damage the motherboard.
2 Safety Information
Specifications
CPU |
Supports 9th/8th Gen Intel® Core™/ Pentium® Gold/ Celeron® |
|
processors for Socket LGA1151 |
||
|
||
|
|
|
Chipset |
Intel® B365 Chipset |
|
|
y 4x DDR4 memory slots, support up to 64GB |
|
|
y Supports DDR4 2666/ 2400/ 2133 MHz Memory |
|
Memory |
y Supports Dual-Channel mode |
|
y Supports non-ECC, un-buffered memory |
||
|
y Supports Intel® Extreme Memory Profile (XMP) |
|
|
* Please refer www.msi.com for more information on |
|
|
compatible memory. |
|
Expansion Slots |
y 1x PCIe 3.0 x16 slot |
|
|
y 2x PCIe 3.0 x1 slots |
|
|
y 1x VGA port, supports a maximum resolution of |
|
|
2048x1536@50Hz, 2048x1280@60Hz, 1920x1200@60Hz |
|
Onboard |
y 1x DVI-D port, supports a maximum resolution of |
|
Graphics |
1920x1200@60Hz |
|
|
y 1x HDMI™ port 1.4, supports a maximum resolution of |
|
|
4096x2160@30Hz |
|
|
Intel® B365 Chipset |
|
|
y 6x SATA 6Gb/s ports* |
|
|
y 1x M.2 slot (Key M) |
|
|
Support up to PCIe 3.0 x4 and SATA 6Gb/s |
|
Storage |
Supports 2242/ 2260 /2280/ 22110 storage devices |
|
Intel® Optane™ Memory Ready** |
||
|
||
|
* The SATA1 connector will be unavailable when an M.2 SATA |
|
|
SSD module has been installed in the M.2_1 slot. |
|
|
** Before using Intel® Optane™ memory modules, please |
|
|
ensure that you have updated the drivers and BIOS to the |
|
|
latest version from MSI website. |
|
|
|
|
|
y Intel® B365 Chipset |
|
|
8x USB 3.1 Gen1 (SuperSpeed USB) ports (3 Type-A & 1 |
|
USB |
Type-C ports on the back panel, 4 ports available through |
|
the internal USB connectors) |
||
|
6x USB 2.0 (High-speed USB) ports (2 Type-A ports on |
|
|
the back panel, 4 ports available through the internal USB |
|
|
connectors) |
|
|
|
|
|
Continued on next page |
Specifications 3
|
Continued from previous page |
|
|
|
|
Audio |
y Realtek® ALC892 Codec |
|
y 7.1-Channel High Definition Audio |
||
|
||
|
|
|
LAN |
1x Realtek 8111H Gigabit LAN controller |
|
|
|
|
|
y 1x PS/2 keyboard port |
|
|
y 1x PS/2 mouse port |
|
|
y 1x VGA port |
|
|
y 1x DVI-D port |
|
Back Panel |
y 1x HDMI™ port |
|
Connectors |
y 1x LAN (RJ45) port |
|
|
y 2x USB 2.0 Type-A ports |
|
|
y 3x USB 3.1 Gen1 Type-A ports |
|
|
y 1x USB 3.1 Gen1 Type-C port |
|
|
y 3x Audio jacks |
|
|
|
|
|
y 1x 24-pin ATX main power connector |
|
|
y 1x 8-pin ATX 12V power connector |
|
|
y 6x SATA 6Gb/s connectors |
|
|
y 2x USB 3.1 Gen1 connector (supports additional 4 USB 3.1 |
|
|
Gen1 ports) |
|
|
y 2x USB 2.0 connectors (supports additional 4 USB 2.0 ports) |
|
|
y 1x 4-pin CPU fan connector |
|
Internal |
y 2x 4-pin system fan connectors |
|
|
||
Connectors |
y 1x Front panel audio connector |
|
|
y 1x Parallel port connector |
|
|
y 1x Serial port connector |
|
|
y 2x Front panel connectors |
|
|
y 1x TPM module connector |
|
|
y 1x 4-pin RGB LED connector |
|
|
y 1x Chassis Intrusion connector |
|
|
y 1x Clear CMOS jumper |
|
|
|
|
I/O Controller |
NUVOTON NCT6797D Controller Chip |
|
|
|
|
Hardware |
y CPU/System temperature detection |
|
y CPU/System fan speed detection |
||
Monitor |
||
y CPU/System fan speed control |
||
|
||
|
|
|
|
Continued on next page |
4 Specifications
Continued from previous page
Form Factor |
y m-ATX Form Factor |
|
|
y 9.6 in. x 9.6 in. (24.4 cm x 24.4 cm) |
|||
|
|||
|
|
|
|
|
y 1x 128 Mb flash |
|
|
BIOS Features |
y UEFI AMI BIOS |
|
|
y ACPI 6.1 , SM BIOS 2.8 |
|
||
|
|
||
|
y Multi-language |
|
|
|
|
|
|
|
y Drivers |
|
|
|
y DRAGON CENTER |
|
|
Software |
y CPU-Z MSI GAMING |
|
|
y Intel® Extreme Tuning Utility |
|
||
|
|
||
|
y Google Chrome™, Google Toolbar, Google Drive |
||
|
y Norton™ Internet Security Solution |
||
|
|
|
|
|
y OC Performance |
|
|
Dragon Center |
y Hardware Monitor |
|
|
y Eyerest |
|
||
Features |
|
||
y Live Update |
|
||
|
|
||
|
y Mystic Light |
Please refer to http:// |
|
|
|
download.msi.com/manual/ |
|
|
|
mb/DRAGONCENTER2.pdf for |
|
|
|
more details. |
Specifications 5
Rear I/O Panel
Line-in
Line-out
PS/2 Mouse |
VGA |
LAN |
|
|
|
|
|
||
|
|
|
|
|
|
|
USB 3.1 Gen1 |
|
|
PS/2 Keyboard |
DVI-D |
USB 2.0 |
USB 3.1 Gen1 |
Mic in |
|
|
|
Type-C |
|
LAN Port LED Status Table
Link/ Activity LED
Status Description
Off |
No link |
Yellow |
Linked |
|
|
Blinking |
Data activity |
Speed LED
Status |
Description |
Off |
10 Mbps connection |
Green |
100 Mbps connection |
|
|
Orange |
1 Gbps connection |
Audio 7.1-channel Configuration
To configure 7.1-channel audio, you have to connect front audio I/O module to JAUD1 connector and follow the below steps.
1.Click on the Realtek HD Audio Manager > Advanced Settings to open the dialog below.
2.Select Mute the rear output device, when a front headphone plugged in.
3.Plug your speakers to audio jacks on rear and front I/O panel. When you plug into a device at an audio jack, a dialogue window will pop up asking you which device is current connected.
6 Rear I/O Panel
Overview of Components
CPU Socket |
DIMMA1 |
SYS_FAN1 CPU_PWR1
|
DIMMA2 |
CPU_FAN1 |
DIMMB1 |
|
|
|
DIMMB2 |
|
SYS_FAN2 |
|
EZ Debug LED |
50.77mm* |
|
|
ATX_PWR1 |
|
JUSB3 |
PCI_E1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
JUSB4 |
||||||
M2_1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
JTPM1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SATA▼1▲2 |
|||||||||
PCI_E2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
JRGB1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SATA3 |
|||||
PCI_E3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SATA4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
JAUD1 |
|
|
JLPT1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
JFP1 |
||||||||||||||||
|
|
|
|
|
|
|
JCOM1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SATA5 |
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
JUSB1 |
|
|
|
|
|
SATA6 |
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
JBAT1 |
|
|
|
JUSB2 |
|
JCI1 |
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
JFP2 |
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
* Distance from the center of the CPU to the nearest DIMM slot.
Overview of Components 7
DIMM Slots
Please install the memory module into the DIMM slot as shown below.
|
|
2 |
1 |
2 |
3 |
1 |
3 |
|
|
|
Memory module installation recommendation
|
DIMMB2 |
DIMMB2 |
|
|
DIMMB1 |
DIMMA2 |
DIMMA2 |
DIMMA2 |
|
|
DIMMA1 |
Important
y To boot up the system successfully, always insert the memory module into DIMMA2 first.
y Due to chipset resource usage, the available capacity of memory will be a little less than the amount of installed.
y Please note that the maximum capacity of addressable memory is 4GB or less for 32-bit Windows OS due to the memory address limitation. Therefore, we
recommended that you to install 64-bit Windows OS if you want to install more than 4GB memory on the motherboard.
8 Rear I/O Panel
CPU Socket
Please install the CPU into the CPU socket as shown below.
2
1
3
8 7
5
4 6
9
Important
yAlways unplug the power cord from the power outlet before installing or removing the CPU.
yPlease retain the CPU protective cap after installing the processor. MSI will deal with Return Merchandise Authorization (RMA) requests if only the motherboard comes with the protective cap on the CPU socket.
yWhen installing a CPU, always remember to install a CPU heatsink. A CPU heatsink is necessary to prevent overheating and maintain system stability.
yConfirm that the CPU heatsink has formed a tight seal with the CPU before booting your system.
yOverheating can seriously damage the CPU and motherboard. Always make sure the cooling fans work properly to protect the CPU from overheating. Be sure to apply an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to enhance heat dissipation.
yWhenever the CPU is not installed, always protect the CPU socket pins by covering the socket with the plastic cap.
yIf you purchased a separate CPU and heatsink/ cooler, Please refer to the documentation in the heatsink/ cooler package for more details about installation.
Rear I/O Panel 9
PCI_E1~3: PCIe Expansion Slots
PCI_E1: PCIe 3.0 x16 (CPU lanes)
PCI_E2: PCIe 3.0 x1 slot (PCH lanes)
PCI_E3: PCIe 3.0 x1 slot (PCH lanes)
Important
yIf you install a large and heavy graphics card, you need to use a tool such as MSI Gaming Series Graphics Card Bolster to support its weight to prevent deformation of the slot.
yFor a single PCIe x16 expansion card installation with optimum performance, using the PCI_E1 slot is recommended.
yWhen adding or removing expansion cards, always turn off the power supply and unplug the power supply power cable from the power outlet. Read the expansion card’s documentation to check for any necessary additional hardware or software changes.
JRGB1: RGB LED connector
This connector allows you to connect the 5050 RGB LED strips 12V.
|
1 |
|
|
|
|
1 |
+12V |
2 |
G |
|
|
3 |
R |
4 |
B |
|
|
|
|
|
|
Extension cable |
LED strip |
|
|
|
JRGB1 |
|
|
|
CAUTION |
|
|
|
|
|
|
|
|
|
Do not connect the wrong type of LED strips. Connecting the 5V LED strip to the JRGB connector will result in damage to the LED strip.
Important
yThe JRGB connector supports up to 2 meters continuous 5050 RGB LED strips (12V/G/R/B) with the maximum power rating of 3A (12V).
yAlways turn off the power supply and unplug the power cord from the power outlet before installing or removing the RGB LED strip.
yPlease use MSI’s software to control the extended LED strip.
10 Rear I/O Panel
JFP1, JFP2: Front Panel Connectors
These connectors connect to the switches and LEDs on the front panel.
2 |
10 |
1 |
HDD LED + |
2 |
Power LED + |
|
3 |
HDD LED - |
4 |
Power LED - |
|||
|
|
|||||
1 |
9 |
5 |
Reset Switch |
6 |
Power Switch |
|
7 |
Reset Switch |
8 |
Power Switch |
|||
JFP1 |
|
|||||
|
|
9 |
Reserved |
10 |
No Pin |
HDD LEDSWRESET
JFP1
|
HDD LED |
|
|
|
|
|
HDD LED - |
|
|
|
|
|
|
|
HDD LED + |
|
|
|
|
|
|
|
POWER LED - |
|
POWER LED |
|
|
|
|
|
POWER LED + |
|
|
|
|
|
|
|
1 |
|
|
|
|
1 |
Speaker - |
2 |
Buzzer + |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
Buzzer - |
4 |
Speaker + |
|
JFP2 |
||||||||
|
|
|
|
|
|
|
|
|
|
SATA1~6: SATA 6Gb/s Connectors
These connectors are SATA 6Gb/s interface ports. Each connector can connect to one SATA device.
SATA6
SATA5 |
SATA4 |
|
SATA3 |
|
SATA2 |
|
SATA1 |
Important
yPlease do not fold the SATA cable at a 90-degree angle. Data loss may result during transmission otherwise.
ySATA cables have identical plugs on either sides of the cable. However, it is recommended that the flat connector be connected to the motherboard for space saving purposes.
Rear I/O Panel 11
M2_1: M.2 Slot (Key M)
Please install the M.2 solid-state drive (SSD) into the M.2 slot as shown below.
|
3 |
Supplied |
|
M.2 screw |
|
2 |
30° |
4 |
|
||
|
|
1
Important
yIntel® RST only supports PCIe M.2 SSD with UEFI ROM.
yIntel® Optane™ Memory Ready.
ATX_PWR1, CPU_PWR1: Power Connectors
These connectors allow you to connect an ATX power supply.
|
|
|
|
|
1 |
+3.3V |
13 |
+3.3V |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
+3.3V |
14 |
-12V |
|
|
|
|
|
|
|
|
|
12 |
|
24 |
|
3 |
Ground |
15 |
Ground |
|
|
|
|
|
|
|
|||
|
4 |
+5V |
16 |
PS-ON# |
||||
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5 |
Ground |
17 |
Ground |
|
|
|
|
ATX_PWR1 |
6 |
+5V |
18 |
Ground |
|
|
|
|
7 |
Ground |
19 |
Ground |
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8 |
PWR OK |
20 |
Res |
1 |
|
13 |
|
9 |
5VSB |
21 |
+5V |
|
|
|
|
|
|
|
|||
|
10 |
+12V |
22 |
+5V |
||||
|
|
|
|
|
||||
|
|
|
|
|
11 |
+12V |
23 |
+5V |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
12 |
+3.3V |
24 |
Ground |
8 |
5 |
|
1 |
Ground |
5 |
+12V |
|
|
|
|
|
||
|
|
CPU_PWR1 |
2 |
Ground |
6 |
+12V |
|
|
3 |
Ground |
7 |
+12V |
|
4 |
1 |
|
||||
|
4 |
Ground |
8 |
+12V |
||
|
|
|
Important
Make sure that all the power cables are securely connected to a proper ATX power supply to ensure stable operation of the motherboard.
12 Rear I/O Panel
JUSB1, JUSB2: USB 2.0 Connectors
These connectors allow you to connect USB 2.0 ports on the front panel.
|
|
|
|
|
|
|
1 |
VCC |
2 |
VCC |
|
|
|
|
|
|
|
|
|
|
|
|
2 |
10 |
|
3 |
USB0- |
4 |
USB1- |
|||
|
|
|
|
|
|
|
5 |
USB0+ |
6 |
USB1+ |
|
|
|
|
|
|
|
|
|
|
|
|
1 |
9 |
|
7 |
Ground |
8 |
Ground |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
9 |
No Pin |
10 |
NC |
Important
yNote that the VCC and Ground pins must be connected correctly to avoid possible damage.
yIn order to recharge your iPad,iPhone and iPod through USB ports, please install MSI® DRAGON CENTER software.
JUSB3, JUSB4: USB 3.1 Gen1 Connectors
These connectors allow you to connect USB 3.1 Gen1 ports on the front panel.
10 11
1 20
1 |
Power |
11 |
USB2.0+ |
|
|
|
|
2 |
USB3_RX_DN |
12 |
USB2.0- |
3 |
USB3_RX_DP |
13 |
Ground |
|
|
|
|
4 |
Ground |
14 |
USB3_TX_C_DP |
5 |
USB3_TX_C_DN |
15 |
USB3_TX_C_DN |
|
|
|
|
6 |
USB3_TX_C_DP |
16 |
Ground |
|
|
|
|
7 |
Ground |
17 |
USB3_RX_DP |
8 |
USB2.0- |
18 |
USB3_RX_DN |
|
|
|
|
9 |
USB2.0+ |
19 |
Power |
10 |
NC |
20 |
No Pin |
|
|
|
|
Important
Note that the Power and Ground pins must be connected correctly to avoid possible damage.
Rear I/O Panel 13
JAUD1: Front Audio Connector
This connector allow you to connect audio jacks on the front panel.
|
|
|
|
|
|
|
1 |
MIC L |
2 |
Ground |
|
|
|
|
|
|
|
|
|
|
|
2 |
10 |
|
3 |
MIC R |
4 |
NC |
||||
|
|
|
|
|
|
|
5 |
Head Phone R |
6 |
MIC Detection |
|
|
|
|
|
|
|
|
|
|
|
1 |
9 |
|
7 |
SENSE_SEND |
8 |
No Pin |
||||
|
|
|
|
|
|
|
9 |
Head Phone L |
10 |
Head Phone Detection |
JCOM1: Serial Port Connector
This connector allows you to connect the optional serial port with bracket.
|
|
|
|
|
|
|
1 |
DCD |
2 |
SIN |
|
|
|
|
|
|
|
|
|
|
|
2 |
10 |
|
3 |
SOUT |
4 |
DTR |
||||
|
|
|
|
|
|
|
5 |
Ground |
6 |
DSR |
1 |
9 |
|
7 |
RTS |
8 |
CTS |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
9 |
RI |
10 |
No Pin |
JLPT1: Parallel Port Connector
This connector allows you to connect the optional parallel port with bracket.
|
2 |
|
|
|
|
|
|
|
|
|
|
|
26 |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
25 |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
RSTB# |
|
2 |
|
|
|
|
AFD# |
|
3 |
PRND0 |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 |
ERR# |
|
5 |
|
|
|
|
PRND1 |
|
6 |
PINIT# |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7 |
PRND2 |
|
8 |
|
|
|
LPT_SLIN# |
|
9 |
PRND3 |
|||||||
10 |
Ground |
|
11 |
|
|
|
PRND4 |
|
12 |
Ground |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
13 |
PRND5 |
|
14 |
|
|
|
Ground |
|
15 |
PRND6 |
|||||||
16 |
Ground |
|
17 |
|
|
|
PRND7 |
|
18 |
Ground |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
19 |
ACK# |
|
20 |
|
|
|
Ground |
|
21 |
BUSY |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
22 |
Ground |
|
23 |
|
|
|
|
PE |
|
24 |
Ground |
||||||
25 |
SLCT |
|
26 |
|
|
|
No Pin |
|
|
|
14 Rear I/O Panel
CPU_FAN1, SYS_FAN1~2: Fan Connectors
Fan connectors can be classified as PWM (Pulse Width Modulation) Mode or DC Mode. PWM Mode fan connectors provide constant 12V output and adjust fan speed with speed control signal. DC Mode fan connectors control fan speed by changing voltage. When you plug a 3-pin (Non-PWM) fan to a fan connector in PWM mode, the fan speed will always maintain at 100%, which might create a lot of noise. You can follow the instruction below to adjust the fan connector to PWM or DC Mode.
Default PWM Mode fan connectors |
1 |
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CPU_FAN1 |
|
|
|
|
|||||
Default DC Mode fan connectors |
1 |
|
|
|
|
|
1 |
|
|
|
||
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
SYS_FAN1 |
|
|
|
||||||||
|
SYS_FAN2 |
|||||||||||
|
|
|
|
|
|
|
|
|
Switching fan mode and adjusting fan speed
You can switch between PWM mode and DC mode and adjust fan speed in BIOS > HARDWARE MONITOR.
Select PWM mode or DC mode
There are gradient points of the fan speed that allow you to adjust fan speed in relation to CPU temperature.
Important
Make sure fans are working properly after switching the PWM/ DC mode.
Pin definition of fan connectors
PWM Mode pin definition
1 |
Ground |
2 |
+12V |
|
3 |
Sense |
4 |
Speed Control |
|
Signal |
||||
|
|
|
DC Mode pin definition
1 |
Ground |
2 |
Voltage |
|
Control |
||||
|
|
|
||
3 |
Sense |
4 |
NC |
Rear I/O Panel 15
JTPM1: TPM Module Connector
This connector is for TPM (Trusted Platform Module). Please refer to the TPM security platform manual for more details and usages.
|
|
|
|
|
|
|
|
|
1 |
LPC Clock |
2 |
3V Standby power |
|
|
|
|
|
|
|
|
|
3 |
LPC Reset |
4 |
3.3V Power |
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
14 |
|
5 |
LPC address & data pin0 |
6 |
Serial IRQ |
||||||
|
|
|
|
|
|
|
|
|
7 |
LPC address & data pin1 |
8 |
5V Power |
1 |
13 |
|
9 |
LPC address & data pin2 |
10 |
No Pin |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
11 |
LPC address & data pin3 |
12 |
Ground |
|
|
|
|
|
|
|
|
|
13 |
LPC Frame |
14 |
Ground |
EZ Debug LED
These LEDs indicate the status of the motherboard.
CPU - indicates CPU is not detected or fail.
DRAM - indicates DRAM is not detected or fail.
VGA - indicates GPU is not detected or fail.
BOOT - indicates booting device is not detected or fail.
16 Rear I/O Panel
JCI1: Chassis Intrusion Connector
This connector allows you to connect the chassis intrusion switch cable.
|
|
|
|
|
Normal |
Trigger the chassis |
|||
(default) |
intrusion event |
|||
|
|
Using chassis intrusion detector
1.Connect the JCI1 connector to the chassis intrusion switch/ sensor on the chassis.
2.Close the chassis cover.
3.Go to BIOS > Security > Chassis Intrusion Configuration.
4.Set Chassis Intrusion to Enabled.
5.Press F10 to save and exit and then press the Enter key to select Yes.
6.Once the chassis cover is opened again, a warning message will be displayed on screen when the computer is turned on.
Resetting the chassis intrusion warning
1.Go to BIOS > Security > Chassis Intrusion Configuration.
2.Set Chassis Intrusion to Reset.
3.Press F10 to save and exit and then press the Enter key to select Yes.
JBAT1: Clear CMOS (Reset BIOS) Jumper
There is CMOS memory onboard that is external powered from a battery located on the motherboard to save system configuration data. If you want to clear the system configuration, set the jumpers to clear the CMOS memory.
|
|
|
|
|
Keep Data |
Clear CMOS/ Reset |
|||
(default) |
BIOS |
Resetting BIOS to default values
1.Power off the computer and unplug the power cord
2.Use a jumper cap to short JBAT1 for about 5-10 seconds.
3.Remove the jumper cap from JBAT1.
4.Plug the power cord and power on the computer.
Rear I/O Panel 17
BIOS Setup
The default settings offer the optimal performance for system stability in normal conditions. You should always keep the default settings to avoid possible system damage or failure booting unless you are familiar with BIOS.
Important
yBIOS items are continuously update for better system performance. Therefore, the description may be slightly different from the latest BIOS and should be for reference only. You could also refer to the HELP information panel for BIOS item description.
yThe pictures in this chapter are for reference only and may vary from the product you purchased.
Entering BIOS Setup
Please refer the following methods to enter BIOS setup.
yPress Delete key, when the Press DEL key to enter Setup Menu, F11 to enter Boot Menu message appears on the screen during the boot process.
yUse MSI DRAGON CENTER application. Click on GO2BIOS button and choose OK. The system will reboot and enter BIOS setup directly.
Function key
F1: General Help
F2: Add/ Remove a favorite item
F3: Enter Favorites menu
F4: Enter CPU Specifications menu
F5: Enter Memory-Z menu
F6: Load optimized defaults
F7: Switch between Advanced mode and EZ mode
F8: Load Overclocking Profile
F9: Save Overclocking Profile
F10: Save Change and Reset*
F12: Take a screenshot and save it to USB flash drive (FAT/ FAT32 format only). Ctrl+F: Enter Search page
* When you press F10, a confirmation window appears and it provides the modification information. Select between Yes or No to confirm your choice.
18 BIOS Setup
Resetting BIOS
You might need to restore the default BIOS setting to solve certain problems. There are several ways to reset BIOS:
yGo to BIOS and press F6 to load optimized defaults.
yShort the Clear CMOS jumper on the motherboard.
Important
Be sure the computer is off before clearing CMOS data. Please refer to the Clear CMOS jumper section for resetting BIOS.
Updating BIOS
Updating BIOS with M-FLASH
Before updating:
Please download the latest BIOS file that matches your motherboard model from MSI website. And then save the BIOS file into the USB flash drive.
Updating BIOS:
1.Press Del key to enter the BIOS Setup during POST.
2.Insert the USB flash drive that contains the update file into the computer.
3.Select the M-FLASH tab and click on Yes to reboot the system and enter the flash mode.
4.Select a BIOS file to perform the BIOS update process.
5.After the flashing process is 100% completed, the system will reboot automatically.
Updating the BIOS with MSI DRAGON CENTER
Before updating:
Make sure the LAN driver is already installed and the Internet connection is set properly.
Updating BIOS:
1.Install and launch MSI DRAGON CENTER.
2.Select BIOS Update.
3.Click on Scan button.
4.Click on Download icon to download and install the latest BIOS file.
5.Click Next and choose In Windows mode. And then click Next and Start to start updating BIOS.
6.After the flashing process is 100% completed, the system will restart automatically.
BIOS Setup 19
Installing OS, Drivers & Utilities
Please download and update the latest utilities and drivers at www.msi.com
Installing Windows® 10
1.Power on the computer.
2.Insert the Windows® 10 installation disc/USB into your computer.
3.Press the Restart button on the computer case.
4.Press F11 key during the computer POST (Power-On Self Test) to get into Boot Menu.
5.Select the Windows® 10 installation disc/USB from the Boot Menu.
6.Press any key when screen shows Press any key to boot from CD or DVD...
message.
7.Follow the instructions on the screen to install Windows® 10.
Installing Drivers
1.Start up your computer in Windows® 10.
2.Insert MSI® Driver Disc into your optical drive.
3.Click the Select to choose what happens with this disc pop-up notification, then select Run DVDSetup.exe to open the installer. If you turn off the AutoPlay feature from the Windows Control Panel, you can still manually execute the DVDSetup.exe from the root path of the MSI Driver Disc.
4.The installer will find and list all necessary drivers in the Drivers/Software tab.
5.Click the Install button in the lower-right corner of the window.
6.The drivers installation will then be in progress, after it has finished it will prompt you to restart.
7.Click OK button to finish.
8.Restart your computer.
Installing Utilities
Before you install utilities, you must complete drivers installation.
1.Open the installer as described above.
2.Click the Utilities tab.
3.Select the utilities you want to install.
4.Click the Install button in the lower-right corner of the window.
5.The utilities installation will then be in progress, after it has finished it will prompt you to restart.
6.Click OK button to finish.
7.Restart your computer.
20 Installing OS, Drivers & Utilities
MSI® B365M PRO-VDH ., , BIOS.
|
|
|
........................................................................................................... |
|
2 |
................................................................................................................... |
|
3 |
I/O ..................................................................................................... |
|
6 |
LAN LED ....................................................................................... |
6 |
|
........................................................................................................ |
|
7 |
DIMM ........................................................................................................... |
8 |
|
CPU .............................................................................................................. |
9 |
|
PCI_E1~3: PCIe .................................................................................. |
10 |
|
JRGB1: RGB LED ................................................................................... |
10 |
|
JFP1, JFP2: ............................................................................ |
11 |
|
SATA1~6: SATA 6Gb/s ............................................................................ |
11 |
|
M2_1: M.2 (Key M)..................................................................................... |
12 |
|
ATX_PWR1, CPU_PWR1: ................................................................ |
12 |
|
JUSB1, JUSB2: USB 2.0 ......................................................................... |
13 |
|
JUSB3, JUSB4: USB 3.1 Gen1 ............................................................... |
13 |
|
JAUD1: |
................................................................................ |
14 |
JCOM1: |
................................................................................ |
14 |
JLPT1: ................................................................................. |
14 |
|
CPU_FAN1, SYS_FAN1~2: ................................................................. |
15 |
|
JTPM1: TPM ................................................................................... |
16 |
|
EZ LED ................................................................................................... |
16 |
|
JCI1: ........................................................................................ |
17 |
|
JBAT1: CMOS (Reset BIOS) ............................................................ |
17 |
|
BIOS( ) ........................................................................................ |
18 |
|
BIOS( ) ........................................................................................... |
18 |
|
BIOS( ) ........................................................................................... |
19 |
|
BIOS( ) .................................................................................... |
19 |
|
OS, & ................................................................... |
20 |
|
Windows® 10 ....................................................................... |
20 |
|
.............................................................................................. |
20 |
|
.............................................................................................. |
20 |
1
y (ESD).
y . ,.
y .
y ESD. ESD ,.
y .
y .
y . ,.
y .
y .
y . y .
y PSU PSU.
y . . y .
y , .:.
.
..
.
y 60°C(140°F) . .
2
|
|
|||
CPU |
LGA1151 8/9 ® ™/ ® / ® |
|||
|
|
|
|
|
|
® B365 |
|
|
|
|
y DDR4 4 , 64GB |
|||
|
y DDR4 2666/ 2400/ 2133 MHz |
|||
|
y |
|
||
y non-ECC, un-buffered |
||||
|
y ® (XMP) |
|||
|
* http://www.msi.com |
|||
|
. |
|||
|
y PCIe 3.0 x16 1 |
|||
y PCIe 3.0 x1 2 |
|
|||
|
y VGA 1 , 2048x1536@50Hz, 2048x1280@60Hz, |
|||
|
1920x1200@60Hz |
|
||
y DVI-D 1 , |
|
1920x1200@60Hz |
||
|
y HDMI™ 1.4 1 , |
4096x2160@30Hz |
||
|
® B365 |
|
|
|
|
y SATA 6Gb/s 6 * |
|
||
|
y M.2 |
1 (Key M) |
SATA 6Gb/s |
|
|
|
PCIe 3.0 x4 |
||
|
2242/ 2260 /2280/ 22110 |
|||
|
® Optane™ Memory Ready** |
|||
|
* M.2_1 M.2 SATA SSD SATA1 |
|||
|
. |
|||
|
** ® Optane™ , |
|||
|
BIOS |
|||
|
. |
|
|
|
|
y ® B365 |
|
||
USB |
USB 3.1 Gen1 ( USB) 8 ( A |
|||
3 & C 1 , USB 4 ) |
||||
|
USB 2.0 ( USB) 6 ( A 2 |
|||
|
, USB 4 ) |
|||
|
|
|
3
|
|
|||
|
y Realtek® ALC892 |
|||
y |
|
|
|
|
|
7.1- HD |
|||
LAN |
Realtek 8111H Gigabit LAN 1 |
|||
|
y PS/2 1 |
|||
|
y PS/2 1 |
|||
|
y VGA 1 |
|
|
|
|
y DVI-D 1 |
|
|
|
|
y HDMI™ 1 |
|
|
|
y LAN (RJ45) |
1 |
|||
|
y USB 2.0 A 2 |
|||
|
y USB 3.1 Gen1 A 3 |
|||
|
y USB 3.1 Gen1 C 1 |
|||
|
y 3 |
|
|
|
|
y 24 ATX 1 |
|||
|
y 8 ATX 12V |
1 |
||
|
y SATA 6Gb/s |
6 |
||
|
y USB 3.1 Gen1 2 ( USB 3.1 Gen1 4 ) |
|||
|
y USB 2.0 2 ( USB 2.0 4 ) |
|||
|
y 4 CPU |
1 |
||
|
y 4 2 |
|||
y 1 |
||||
|
y |
1 |
||
|
y |
1 |
||
|
y |
2 |
||
|
y TPM |
1 |
||
|
y 4 RGB LED 1 |
|||
|
y |
1 |
||
|
y CMOS |
1 |
||
I/O |
NUVOTON NCT6797D |
yCPU/y CPU/
yCPU/
4
|
|
|
|
|
y m-ATX |
|
|
y 9.6 in. x 9.6 in. (24.4 cm x 24.4 cm) |
|||
|
y 128 Mb 1 |
||
BIOS |
y UEFI AMI BIOS |
|
|
y ACPI 6.1 , SM BIOS 2.8 |
|||
|
y |
|
|
|
y |
|
|
|
y |
|
|
|
y CPU-Z MSI |
|
|
y |
® |
||
|
y |
: |
, , |
|
y |
™ |
|
|
y OC |
|
|
|
y |
|
|
y Eyerest |
|
||
|
y Live |
http:// |
|
|
y |
|
|
|
|
download.msi.com/manual/ |
|
|
|
|
mb/DRAGONCENTER2.pdf |
|
|
|
. |
5
I/O
Line Line
PS/2 |
VGA |
LAN |
|
|
|
|
|
|
|||
|
|
|
|
||
|
|
|
USB 3.1 Gen1 |
|
|
PS/2 |
DVI-D |
USB 2.0 |
USB 3.1 Gen1 |
Mic |
|
LAN LED |
|
C |
|
||
|
|
|
|||
/ LED |
|
LED |
|
|
|
|
|
|
|
|
|
|
LAN |
|
10 Mbps . |
||
. |
|
|
100 Mbps |
|
|
|
LAN |
. |
|
||
. |
|
1 Gbps . |
|||
|
LAN |
|
|
|
|
. |
|
|
|
||
Audio 7.1- |
|
|
|
||
7.1 I/O JAUD1 . |
|||||
. |
|
|
|
1.Realtek HD Audio Manager (Realtek HD ) > Advanced Settings() .
2.[Mute the rear output device, when a front headphone plugged in]() .
3.I/O ..
6 I/O
CPU |
DIMMA1 |
|
SYS_FAN1 CPU_PWR1
|
DIMMA2 |
CPU_FAN1 |
DIMMB1 |
|
|
|
DIMMB2 |
|
SYS_FAN2 |
|
EZ Debug LED |
50.77mm* |
|
|
ATX_PWR1 |
|
JUSB3 |
PCI_E1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
JUSB4 |
||||||
M2_1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
JTPM1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SATA▼1▲2 |
|||||||||
PCI_E2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
JRGB1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SATA3 |
|||||
PCI_E3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SATA4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
JAUD1 |
|
|
JLPT1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
JFP1 |
||||||||||||||||
|
|
|
|
|
|
|
JCOM1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SATA5 |
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
JUSB1 |
|
|
|
|
|
SATA6 |
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
JBAT1 |
|
|
|
JUSB2 |
|
JCI1 |
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
JFP2 |
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*CPU DIMM
7
DIMM
DIMM .
|
|
2 |
1 |
2 |
3 |
1 |
3 |
|
|
|
( )
|
DIMMB2 |
DIMMB2 |
|
|
DIMMB1 |
DIMMA2 |
DIMMA2 |
DIMMA2 |
|
|
DIMMA1 |
yDIMMA2 .
y.
y4GB 32- (Windows OS). 4GB 64Windows OS .
8 I/O
CPU
CPU CPU .
2
1
3
8 7
5
4 6
9
yCPU .
y, CPU . CPUMSI (RMA) .
yCPU , CPU . CPU.
yCPU .
yCPU CPU. CPU( ) .
yCPU , CPU..
yCPU / , /.
I/O 9
PCI_E1~3: PCIe
PCI_E1: PCIe 3.0 x16 (CPU )
PCI_E2: PCIe 3.0 x1 (PCH )
PCI_E3: PCIe 3.0 x1 (PCH )
y,MSI Gaming Series Graphics Card Bolster.
yPCIe x16 PCI_E1.
y..
JRGB1: RGB LED
5050 RGB LED 12V .
|
1 |
|
|
|
1 |
+12V |
2 |
G |
|
3 |
R |
4 |
B |
|
|
|
|
JRGB1 |
LED |
|
|
|
LED . 5V LED JRGB LED .
yJRGB 3A (12V) 2 5050 RGB LED (12V/G/R/B) .
yRGB LED .
yMSI LED .
10 I/O