Motorola T5950 User Manual

4 (1)
Motorola T5950 User Manual

User's Guide

Guide d'utilisation

TWO-WAY RADIOS/APPAREILS RADIOS

-RÉCEPTEUR

KEM-PK9659B-02

Models T5900, T5920 and T5950 series

 

Modèles des séries T5900, T5920 et T5950

Contents

 

Safety and General Information ....................

3

 

Control Buttons ..............................................

11

 

Getting Started ..............................................

12

 

Installing the AA Batteries ..........................

12

 

Installing the NiCd Battery Pack ................

12

 

Battery Meter................................................

13

 

Using the Desk Stand Charger

13

Contents

(Optional Accessory)....................................

Attaching the Belt Clip

15

 

 

Removing the Belt Clip................................

15

 

Turning Your Radio On and Off ..................

15

 

Setting the Volume ......................................

15

 

Setting a Channel ........................................

16

 

Channels and Frequencies ..........................

16

 

Weather Channels and Frequencies ..........

17

 

Talking and Listening ....................................

18

 

Talk Range ....................................................

18

 

Monitor Button ............................................

18

 

Special Features ............................................

19

 

Interference Eliminator Codes ....................

19

 

Push to Talk Timeout Timer ........................

19

 

Locking the Keypad ....................................

20

 

Enhanced Scanning ....................................

20

1

Scan Advance ..............................................

21

Removing Channels from the Scan List

21

(Nuisance Delete Feature)

 

Handsfree Use

 

Without Accessories (iVox) ......................

22

Handsfree Use

 

With Accessories (VOX) ............................

22

Weather (Model T5950 Only) ........................

23

Turning Weather Channel Reception

 

On and Off ......................................................

23

Setting the Weather Channel ........................

24

Turning Keypad Beeps On/Off ......................

24

Alerts ..............................................................

25

Channel Busy Indicator ..............................

25

Setting and Transmitting Call Tones ..........

25

Transmitting a Talk Confirmation

 

Tone ..............................................................

25

QT Noise Filtering ........................................

26

VibraCall® Alert (Models T5920 and

 

T5950 Only) ................................................

27

Accessories ....................................................

28

Using Audio Accessories ............................

28

Setting the Sensitivity Level ......................

28

Patent Information ........................................

30

Export Law Assurances ................................

30

Copyright Information ..................................

30

Warranty..........................................................

31

Table des matières

Information générale et consignes

 

de sécurité ......................................................

37

Boutons de commande ................................

45

Pour commencer ............................................

46

Installation des piles AA..............................

46

Installation du bloc-pile NiCd......................

46

Indicateur de charge ....................................

47

Utilisation du chargeur de table

 

(accessoire offert en option) ......................

47

Installation de la pince pour ceinture ........

49

Retrait de la pince pour ceinture ................

49

Mise en marche de la radio ........................

49

Réglage du volume......................................

49

Sélection du canal........................................

50

Canaux et fréquences ..................................

50

Canaux et fréquences - Météo....................

51

Parler et écouter ............................................

52

Portée ............................................................

52

Bouton de contrôle des canaux..................

52

Caractéristiques spéciales ............................

53

Codes suppresseurs d'interférence............

53

Minuterie Push to Talk (PTT) ......................

53

Verrouillage du clavier ................................

54

Balayage amélioré ......................................

54

Balayage avancé ..........................................

55

Suppression de canaux de la liste

 

de balayage (caractéristique

 

de suppression)..........................................

55

Utilisation mains libres sans

 

accessoires (iVOX) ....................................

56

Utilisation mains libres avec

 

accessoires (VOX)......................................

56

Météo (T5950 seulement) ............................

57

Activation et désactivation de la réception

 

d'un canal météo

 

Mise en marche de la radio ..........................

57

Réglage du canal météo................................

58

Activation et désactivation des

 

touches sonores ..........................................

58

Alertes ............................................................

59

Indicateur de canal occupé ........................

59

Réglage et transmission des

 

signaux d'appel ..........................................

59

Transmission d'un signal de fin d'émission

Signal d'appel ..............................................

59

Filtre antiparasite QT ..................................

60

Alerte VibraCall® (modèles T5920

 

et T5950 seulement) ..................................

61

Accessoires ....................................................

62

Utilisation des accessoires audio ..............

62

Réglage du niveau de sensibilité................

62

Information relative au brevet ......................

64

Exportation ....................................................

64

Information relative aux droits d'auteur ......

64

Garantie ..........................................................

65

Table des matières

2

Safety and General Information

Safety and General Information

Important Information on Safe and Efficient Operation

Read This Information Before Using Your Radio.

The information provided in this document supersedes the general safety information in user guides published prior to December 1, 2002.

Transmit and Receive Procedure

Your two-way radio contains a transmitter and a receiver. To control your exposure and ensure compliance with the general population/uncontrolled environment exposure limits, always adhere to the following procedure:

Transmit no more than 50% of the time.

To transmit (talk), press the Push to Talk (PTT) button.

To receive calls, release the PTT button.

Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy exposure only when transmitting (in terms of measuring standards compliance).

Exposure To Radio Frequency Energy

Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines:

United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J

3

American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992

Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition

International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998

Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999

Australian Communications Authority Radiocommunications (Electromagnetic Radiation --- Human Exposure) Standard, 2003

ANATEL ANNEX to Resolution No. 303 of July 2, 2002 "Regulation of limitation of exposure to electrical, magnetic and electromagnetic fields in the radio frequency range between 9 KHz and 300 GHz" and "Attachment to resolution

# 303 from July 2, 2002"

To assure optimal radio performance and make sure human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards, always adhere to the following procedures.

Portable Radio Operation and EME Exposure

Antenna Care

Use only the supplied or an approved replacement antenna. Unauthorized antennas,modifications, or attachments could damage the radio.

DO NOT hold the antenna when the radio is “IN USE.” Holding the antenna affects the effective range.

Safety and General Information

4

Safety and General Information

Two-way Radio Operation

When using your radio as a traditional two-way radio, hold the radio in a vertical position with the microphone 1 to 2 inches (2.5 to 5 cm) away from the lips.

Body-Worn Operation

To maintain compliance with Health Canada RF exposure guidelines, if you wear a radio on your body when transmitting, always place the radio in a Motorolasupplied or approved clip, holder, holster, case, or body harness for this product. Use of non-Motorola-approved accessories may exceed Health Canada RF exposure guidelines.

If you do not use one of the Motorola-supplied or approved body-worn accessories, and are not using the radio held in the normal use position, ensure the radio and its antenna are at least 1 inch (2.5 cm) from your body when transmitting.

Data Operation

If applicable, when using any data feature of the radio with or without an accessory cable, position the radio and its antenna at least 1 inch (2.5 cm) from the body.

Approved Accessories

For a list of approved Motorola accessories, visit our website at www.Motorola.com.

Electromagnetic Interference/Compatibility

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

Note: Nearly every electronic device is susceptible to electromagnetic interference 5 (EMI) if inadequately shielded, designed, or otherwise configured for

electromagnetic compatibility.

Facilities

To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy.

Aircraft

When instructed to do so, turn off your radio when on board an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions.

Medical Devices - Pacemakers

The Advanced Medical Technology Association recommends that a minimum separation of 6 inches (15 cm) be maintained between a handheld wireless radio and a pacemaker. These recommendations are consistent with the independent research by, and recommendations of the U.S. Food and Drug Administration.

Persons with pacemakers should:

ALWAYS keep the radio more than 6 inches (15 cm) from their pacemaker when the radio is turned ON.

Not carry the radio in the breast pocket.

Use the ear opposite the pacemaker to minimize the potential for interference.

Turn the radio OFF immediately if you have any reason to suspect that interference is taking place.

Safety and General Information

6

Safety and General Information

Medical Devices - Hearing Aids

Some digital wireless radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives.

Other Medical Devices

If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information.

Safety and General Use While Driving

Check the laws and regulations on the use of radios in the area where you drive. Always obey them. When using your radio while driving, please:

Give full attention to driving and to the road.

Use hands-free operation, if available.

Pull off the road and park before making or answering a call if driving conditions so require.

Operational Warnings

For Vehicles with an Air Bag

Do not place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle.

7

Potentially Explosive Atmospheres

Turn off your radio prior to entering any area with a potentially explosive atmosphere, unless it is a radio type especially qualified for use in such areas as “Intrinsically Safe.”

Do not remove, install, or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death.

Note: The areas with potentially explosive atmospheres referred to above include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles, such as grain, dust, or metal powders, and any other area where you would normally be advised to turn off your vehicle engine. Areas with potentially explosive atmospheres are often but not always posted.

Blasting Caps and Areas

To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: “Turn off two-way radio.” Obey all signs and instructions.

Operational Cautions

Antennas

Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.

Safety and General Information

8

Safety and General Information

Batteries

All batteries can cause property damage and/or bodily injury such as burns if a conductive material such as jewelry, keys, or beaded chains touch exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse, or other container with metal objects.

Battery Charger Safety Instructions

Save these Instructions

1.Do not expose the charger to rain or snow.

2.Do not operate or disassemble the charger if it has received a sharp blow, or has been dropped or damaged in any way.

3.Never alter the AC cord or plug provided with the unit. If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. An improper condition can result in a risk of electric shock.

4.To reduce the risk of damage to the cord or plug, pull the plug rather than the cord when disconnecting the charger from the AC receptacle.

5.To reduce the risk of electric shock, unplug the charger from the outlet before attempting any maintenance or cleaning.

6.Use of an attachment not recommended or sold by Motorola may result in a risk of fire, electric shock, or personal injury.

9

7.Make sure the cord is located so it will not be stepped on, tripped over, or subjected to damage or stress.

8.An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of fire and/or electric shock. If an extension cord must be used, make sure that:

The pins on the plug of the extension cord are the same number, size and shape as those on the plug of the charger.

The extension cord is properly wired and in good electrical condition.

The cord size is 18 AWG for lengths up to 30.48 meters, and 16 AWG for lengths up to 45.72 meters.

9.The supply cord of this charger cannot be replaced. If the cord is damaged, call Motorola Product Services at 1-888-390-6456 TTY (Text Telephone).

Note: Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited.

Safety and General Information

10

Control Buttons

Control Buttons

Use to:

Turn radio on/off

Adjust volume

LED indicator light

Use (Push to Talk) to:

• Talk

• Save a setting

Use to:

• Transmit call tone

Speaker

Accessory Jack with

Cover

Use to:

• Monitor channel activity

• Activate enhanced scanning

Use and to:

• Scroll through menus

Microphone

Use to:

• Lock the keypad (when held down and not in menu

• Exit the menu (when pressed while in a menu)

11

Getting Started

Installing the AA Batteries

Your radio uses 3 AA Alkaline batteries.

1.With the back of the radio facing you, lift the battery latch up to release the battery cover and remove the cover.

2.Insert 3 AA Alkaline batteries as shown on the inside of the battery compartment.

3.Reposition the battery cover and press down to secure.

Note: A NiCd rechargeable battery can be used instead of 3 AA Alkaline batteries. A rechargeable battery upgrade kit, model number 53614, is available. For the dealer nearest you, call 1-800-353-2729 in the USA, or visit our website at www.motorola.com/talkabout.

Installing the NiCd Battery Pack

1.Follow step 1 above to remove the battery cover.

2.Remove the battery pack from the clear plastic bag.

Do not disassemble or unwrap the battery pack.

3.Insert the NiCd battery pack so the matel contacts on the side of the battery are facing outward from the radio to connect with the contacts on the battery door.

4.Reposition the battery cover and press down to secure.

Getting Started

12

Getting Started

Battery Meter

The battery icon shows the battery charge level, from full to empty . When the battery is empty, the radio chirps periodically after releasing . The radio powers off when the voltage drops below a predetermined level to protect the rechargeable battery.

Note: Remove the batteries before storing your radio for extended periods of time. Batteries corrode over time and may cause permanent damage to your radio.

Using the Desk Stand Charger (Optional Accessory)

The desk stand charger provides drop-in charging convenience for NiCd batteries and can be placed on any flat surface, such as a desk or workbench. Charge the NiCd battery overnight (at least 16 hours) before using it for the first time. After the initial charge, an empty battery is fully charged within 14 hours.

1.Turn the radio off and remove the battery cover.

2.Remove the battery pack from the clear plastic bag. Do not disassemble or unwrap the battery pack.

3.Insert the NiCd battery pack so the metal contacts on the side of the battery are facing outward from the radio to connect with the contacts on the battery door.

4.Reposition the battery cover and press down to secure.

5.Plug the AC power supply into the plug on the desk stand.

6.Plug the AC power supply into a standard wall outlet.

7.Remove the battery pocket inserts from the charger pockets.

8.With a radio facing forward, slide it into one of the charging pockets.

13

To charge the battery pack separately from the radio:

1.Remove the battery pack from the clear plastic bag.

Do not disassemble or unwrap the battery pack.

2.Make sure the charger pocket inserts are in place.

3.Align the metal contacts on the battery pack with the contacts inside the charger, then insert the battery pack into the pocket.

4.Plug the AC power supply into the plug on the desk stand.

5.Plug the AC power supply into a standard wall outlet.

Notes:

When moving between hot and cold temperatures, do not charge the battery until the battery temperature acclimates (usually about 20 minutes).

For optimal battery life, remove the radio or battery from the charger within 16 hours. Do not store the radio in the charger.

Getting Started

14

Getting Started

Attaching the Belt Clip

1.Align the belt clip post with the hole in the back of the radio.

2.Gently push until the clip clicks into place.

Removing the Belt Clip

1.Push down on the release tab at the top of the belt clip to release the catch.

2.Pull the belt clip away from the back of the radio.

Turning Your Radio On and Off

Turn clockwise to turn the radio on and counterclockwise to turn the radio off. The radio chirps and the display briefly shows all feature icons available on your radio. The display then scrolls through the available channels and Interference Eliminator Codes.

Setting the Volume

Press and hold while rotating until you reach a comfortable listening level. Rotate clockwise to increase or counterclockwise to decrease the volume.

Do not hold the radio close to your ear. If the volume is set to an uncomfortable level, it could hurt your ear.

15

Setting a Channel

Your radio has 22 channels. Channels 1-7 and 15-22 are 1 watt. Channels 8-14 are 0.5 watt. When the radio is on a 1 watt channel, displays. When the radio is on a 0.5 watt channel, displays.

1.With the radio on, press . The current channel flashes.

2.Press or to set the channel.

3.Press to save the channel setting.

Channels and Frequencies

Channel

Frequency

Description

Channel

Frequency

Description

1

462.5625 MHz

GMRS/FRS

12

467.6625 MHz

FRS

2

462.5875 MHz

GMRS/FRS

13

467.6875 MHz

FRS

 

 

 

 

 

 

3

462.6125 MHz

GMRS/FRS

14

467.7125 MHz

FRS

 

 

 

 

 

 

4

462.6375 MHz

GMRS/FRS

15

462.5500 MHz

GMRS

 

 

 

 

 

 

5

462.6625 MHz

GMRS/FRS

16

462.5750 MHz

GMRS

 

 

 

 

 

 

6

462.6875 MHz

GMRS/FRS

17

462.6000 MHz

GMRS

 

 

 

 

 

 

7

462.7125 MHz

GMRS/FRS

18

462.6250 MHz

GMRS

 

 

 

 

 

 

8

467.5625 MHz

FRS

19

462.6500 MHz

GMRS

 

 

 

 

 

 

9

467.5875 MHz

FRS

20

462.6750 MHz

GMRS

 

 

 

 

 

 

10

467.6125 MHz

FRS

21

462.7000 MHz

GMRS

 

 

 

 

 

 

11

467.6375 MHz

FRS

22

462.7250 MHz

GMRS

 

 

 

 

 

 

Getting Started

16

Weather Channels and Frequencies

Weather Channel

Frequency

Weather Channel

Frequency

WX1

162.550 MHz

WX5

162.450 MHz

WX2

162.400 MHz

WX6

162.500 MHz

WX3

162.475 MHz

WX7

162.525 MHz

WX4

163.425 MHz

WX8

162.275 MHz

Getting Started

17

Talking and Listening

To communicate, all radios in your group must be set to the same channel (1-22) and Interference Eliminator Code (0-99).

To talk, press and hold Hold the radio 2 to 3 inches away from your mouth when talking.

When you finish talking, release (press to talk, release to listen).

Talk Range

Your radio is designed to maximize performance and improve transmission range. Do not use the radios closer than 5 feet apart.

Monitor Button

Pressing and holding for 3 seconds allows you to listen to the volume level of the radio when you are not receiving. This allows you to adjust the volume, if necessary. You can also use to check for activity on the current channel before you transmit (talk).

Talking and Listening

18

Special Features

Special Features

Interference Eliminator Codes

Interference Eliminator Codes help minimize interference by providing a choice of code combinations. Your radio has 99 Interference Elimintor Codes. Codes 1-38 are the standard codes that appear on other FRS/GMRS radios. Codes 39-99 are additional digital codes added for superior interference protection.

To set the code for a channel:

1.Press until the code starts to flash.

2.Press or to select the code.

3.Press to save the code setting.

You can set a different code for each channel using this procedure. An extended press of or allow you to scroll through the Interference Eliminator Codes rapidly so you can quickly reach the code you want.

Note: You must set the Interference Eliminator Code to on a radio that uses Interference Eliminator Codes to communicate with radios that do not have Interference Eliminator Codes.

Push to Talk Timeout Timer

To prevent accidental transmissions and save battery life, the radio emits a continuous warning tone and stops transmitting if you press for 60 continuous seconds.

19

Locking the Keypad

To avoid accidentally changing your radio settings, press and hold for 3 seconds or until displays. You can turn the radio on and off, adjust the volume, receive, transmit, send a call tone, and monitor channels. All other functions are locked.

To unlock the radio, press and hold for 3 seconds or until is no longer displayed.

Enhanced Scanning

Scanning is used to:

Monitor Channels and codes for transmissions and lock in on one that interests you.

Find someone in your group who has accidentally changed channels and is talking during your scan.

With enhanced scanning, your home channel is scanned more frequently than any other channel. The home channel is the channel your radio was set

to when you started to scan. If you activate scan while your radio's Interference Eliminator Code is set to a number between 1 and 99, the radio checks for activity on each channel, but only in the specific code selected. All transmissions using code 0 or any other code are ignored.

To start scanning, briefly press and release . The scan indicator displays and the radio begins to scroll through the channel and Interference Eliminator Code combinations.

Special Features

20

Special Features

When the radio detects activity, it stops scanning and you can hear the transmission on that channel. To respond and talk to the person transmitting, press within 5 seconds.

To stop scanning, briefly press and release .

Note: If you press while the radio is scanning, the radio transmit on the channel you selected before you activated scan. If no transmission occurs within 5 seconds, scanning will resume.

Scan Advance

If the radio stops scanning on a channel you do not want to listen to, briefly press and release or to resume scanning for the next active channel.

Removing Channels from the Scan List (Nuisance Delete Feature)

To prevent the radio from scanning a channel, press and hold or for at least 3 seconds, then release, when the scan first stops on that channel. This temporarily removes the channel from the scan list. Press to exit scan mode. Press a second time to activate scan again. To restore a previously deleted channel, turn the radio off and then back on. The channel is now restored.

Note: You cannot remove your home channel from the scan list. The home channel is the channel your radio was set to when you started the scanning.

21

Loading...
+ 50 hidden pages