Motorola NETOPIA 2210-02 User Manual

0 (0)

User Manual

The Motorola Netopia® 2210-02

ADSL2+ Gateway

Single-port Ethernet

Safety Information

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS – POWER SUPPLY INSTALLATION. Connect the power supply cord to the power jack on the Motorola Modem. Plug the power supply into an appropriate electrical outlet.

CAUTION: Depending on the power supply provided with the product, either the direct plug-in power supply blades, power supply cord plug or the appliance coupler serves as the mains power disconnect. It is important that the direct plug-in power supply, socket-outlet or appliance coupler be located so it is readily accessible.

(Sweden) Apparaten skall anslutas till jordat uttag när den ansluts till ett nätverk (Norway) Apparatet må kun tilkoples jordet stikkontakt.

TELECOMMUNICATION INSTALLATION. When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning.

Do not use the telephone to report a gas leak in the vicinity of the leak.

PRODUCT VENTILATION. The Motorola Modem is intended for use in a consumer's home. Ambient temperatures around this product should not exceed 104°F (40°C). It should not be used in locations exposed to outside heat radiation or trapping of its own heat. The product should have at least one inch of clearance on all sides except the bottom when properly installed and should not be placed inside tightly enclosed spaces unless proper ventilation is provided.

SAVE THESE INSTRUCTIONS

Motorola Part Number: 6180206-00-01

Copyright © 2007 by Motorola, Inc.

All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation or adaptation) without written permission from Motorola, Inc.

Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola to provide notification of such revision or change. Motorola provides this guide without warranty of any kind, either implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Motorola may make improvements or changes in the product(s) described in this manual at any time. MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. Microsoft, Windows, Windows Me, and Windows NT are either trademarks or registered trademarks of Microsoft Corporation in the U.S and/or other countries. Macintosh is a registered trademark of Apple, Inc. Firefox is a registered trademark of the Mozilla Foundation. All other product or service names are the property of their respective owners.

2

Motorola NETOPIA 2210-02 User Manual

1 Checklist

Thank you for selecting the Motorola Netopia® 2210-02 ADSL2+ Gateway. This guide will help you set up and configure your network.

Check your package contents. It should contain the items shown here:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CD and

 

 

 

Motorola Modem

User Manual Wallmount Template

Power

Gray RJ-11

Yellow RJ-45

Supply

Phone Cable

Ethernet Cable

If you don’t have everything, contact your supplier immediately.

ENGLISH

3

2 Connections

ENGLISH

Note: Macintosh users: skip to Step #2 below.

1.Windows users: Insert the Motorola Netopia CD into your CDROM drive. The Installation Guide Wizard should start automatically and the Welcome screen should appear to step through your connection installation(s).

The Motorola Netopia Installation Guide Wizard automates several tasks to get you up and running easily. Run the Wizard on every Win- dows-based PC that will connect to your network.

Click the Next button.

Follow the on-screen instructions to make all of your connections.

2.Locate the Modem near a power source, a DSL wall outlet, and in a location where air can circulate freely around it.

3.Connect the rounded end of the power supply to the power jack on the back panel of the Modem. Then, plug the power supply into an electrical outlet.

The Power LED should light solid green.

4.Connect one end of the gray RJ-11 Phone cable to the port labeled “DSL” on the Modem. Connect the other end of the Phone cable to your DSL wall outlet.

4

5.Connect one end of the yellow RJ-45 Ethernet cable to the port labeled “Ethernet” on the modem. Connect the other end of the Ethernet cable to the Ethernet port on your PC.

Rear View

Ethernet

 

 

DSL Port

Port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENGLISH

5

When all of your connections are made, the status LEDs on the front of your Motorola Modem will light, according to the following diagram:

Top View

ENGLISH

Power -

Solid Green = Power on

Off = Power off

Flashing Red = Power On/Self Test

Solid Red = PO/ST Failure

Ethernet -

Solid green = Device connected. Off = No device connected or

modem power is off

Internet -

Solid green = Connected to Internet

Off = Bridge mode or modem power is off

Flashing green = Attempting PPP connection

Red = Connection failed

DSL -

Solid green = DSL synch

Off = Modem power off

Flashing green = DSL attempting synch Flashing green/red = DSL fails to synch 3 times Flashing red = No DSL signal

6

Loading...
+ 12 hidden pages