MotoMon COMMUNICATOR
Installation and Operation Guide
GC 073 431 F
GSM, GPRS, GPS Communicator with driver identification
Tracking and monitoring of vehicles
Transmission of alarms from installed security devices
MotoMon
Global Vehicle Tracking
Dear customer,
Thank you for purchasing our GSM Communicator MotoMon GC 073 431. The MotoMon
communicator is intended for easy installation into vehicles where it provides reception of
GPS coordinates, inputs and outputs operation connected with car alarm system, saving
measured data in the log memory and online communication with a server and integrator
application via GSM/GPRS.
The main applications are vehicle localization, fleet management, electronic book of rides,
vehicle and crew security.
Other features:
Transmission of alarms from vehicle security system to a mobile phone of the owner or to
security agency dispatch center.
Exact localization of vehicle using the GPS coordinates, sent to mobile phone of the owner
or to security agency.
The communicator fully supports SMS commands for parameter settings, setup of output
values, localization and alarm transmissions.
System integrators can use the GC 073 Control Panel software that provides variety of
options for changing configuration parameters of the unit and firmware upgrade using the
USB cable connection, GSM data call or GPRS connection.
For optimal use of the MotoMon communicator, we recommend to read this user guide
carefully. After getting to know the product operation, it is as simple as using a mobile
phone. However, it is recommended to contact a installation company for installation of the
device and putting it into operation.
MotoMon Ltd.
2
Contents:
1. Description ................................................................................................ 5
1.1. Description of the MotoMon Communicator .................................... 5
1.2. Standard Set of Accessories and Optional Accessories ..................... 6
1.3. Basic Operation Description .............................................................. 6
2. Operation .................................................................................................. 7
2.1. Trip type identification – private / work ............................................ 7
2.2. Emergency button .............................................................................. 7
2.3. Reading position using SMS ............................................................. 7
2.4. Reading position using a misscall ...................................................... 7
2.5. Vehicle shutdown .............................................................................. 8
2.6. Transmission of alarm from installed security device ....................... 8
3. Installation ................................................................................................ 9
3.1. Definition of Usage, Safety ............................................................... 9
3.2. Connection drawing ......................................................................... 10
............................................................................................................10
3.3. Instructions for Installation .............................................................. 11
3.4. LED signalling ................................................................................. 12
3.5. Testing SMS .................................................................................... 12
3.6. Checking Correct Function .............................................................. 13
4. Configuration .......................................................................................... 14
4.1. SIM, SMS, APN, server .................................................................. 14
4.2. Password, list of phone numbers, credit .......................................... 15
5. Technical Parameters, Maintenance ....................................................... 16
5.1. Technical parameters ....................................................................... 16
5.2. Maintenance ..................................................................................... 17
5.3. Troubleshooting ............................................................................... 18
Warranty conditions ................................................................................ 20
Warranty certificate ................................................................................ 21
3
1. Description
1.1. Description of the MotoMon Communicator
4
1.2. Standard Set of Acces sories and Optional Accessories
Accessories delivered in the set F
GC 073 431
ED 001 006
ED 002 002
CB 170 307
CB 161 001
MotoMon Communicator
GSM antenna
GPS antenna active with SMB connector
Electro-mounting set (12pin Micro Mate N-lock connector, cables 2m)
Set of installation parts
Optional accessories
ED 060 601
ED 060 615
ED 060 614
CB 170 020
ED 060 613
Emergency button
Switch of trip type (work – private)
Vehicle relay (12V, 30 A, switching, in plastic case, Faston)
Mini-USB PC cable
Crash sensor
1.3. Basic Operation Description
When the vehicle ignition is switched on, the unit “wakes up” from the sleep mode with low
power consumption, the unit gets connection to the internet via GPRS and starts sending
packets with position data to the predefined server. At the same time the unit starts saving
data about the ride into its memory. The position is saved in dependance on velocity and
change of ride direction approximately once in a minute. Switching the ignition will stop
saving the ride data and it will signalize to the server to start downloading the ride data
from unit’s memory. After downloading data the unit switches back to sleep mode to save
power consumption, stops sending the ID packets and the driver is logged-out.
5
2. Operation
2. 1. Trip type identification – private / work
To identify the trip type use the switch ED 060 615. To indicate private trip, the switch must
be in position marked with the dot. Switching during the ride will divide the trip into two.
Private trips can be hidden – that is done by the supervision system – the information
about private trip is still stored in the supervision system.
2. 2. Emergency button
Press the emergency button ED 060 601 to send an alarm SMS with vehicle location to
predefined phone numbers. It is possible to connect the crash sensor ED 060 613 to the
emergency button input, this will send alarm SMS automatically in case of activation of the
sensor.
2. 3. Reading position using SMS
When the communication unit receives SMS inquiry for position from any mobile phone, it
will respond with message with the current GPS coordinates to sender’s number. Position
of vehicle can be then displayed using internet map services such as maps.google.com,
www.mapy.cz, etc. Reading of GPS coordinates might take up to 5 minutes, if it is not
possible to read the position (GPS receiver does not have valid coordinates), last known
position will be sent.
Reading GPS position
SMS
Reply
password GPSD
default password from production is: picola
gpsd x y
x= latitude in format: 50.402706 N
y= longitude in format: 16.145190 E
2. 4. Reading position using a misscall
Reading position of vehicle is also possible by calling the phone number of SIM card in the
communication unit. The number should be predefined in the phone list of communicator
on positions tel1 and tel2. Confirmation of receiving the command is done by rejecting the
call by communicator.
Example of reply SMS:
Reply At maps.google.com type: 50.42035 N 16.16825 E, position saved
before: 12:36 (h:m), GSM BTS code: 6787, GSM signal: 16 (32=max)
There are databases of BTS (Base Transceiver Station) of local mobile operators on the
Internet (e.g. www.gsmweb.cz for operators in the Czech Republic) and it is possible to
find out the position very roughly – and with no guarantee.
6
2. 5. Vehicle shutdown
Safe shutdown of vehicle can be done by sending SMS command to the communication
unit in vehicle – if this feature is installed and configured. The vehicle shutdown is
launched only when the speed decreases under 10 km/h using the immobilization relay
ED 060 614 that will disconnect the immobilization circuit of vehicle.
Vehicle shutdown
SMS
Reply
- Confirmation
- Launching
- Not launching
password STOP
default password from production is: picola
SMS confirmation about action launching / not launching will be sent to
phone numbers predefined in GC 073 phone list on positions tel1 and
tel2.
STOP.Run – action was launched (sent to sender for command SMS)
STOP AT POSITION: geographical position
STOP NOT MADE! Speed of vehicle did not decrease under 10 km/h in
the past 30 minutes (or the GPS receiver does not have valid data) and
action was cancelled
Starting vehicle again
SMS
Confirmation
password START
START.Run – enables the possibility to start ignition again
2. 6. Transmission of alarm from installed security device
If the communicator unit is connected to the existing vehicle alarm system, it will work as
SMS detector of alarm status. Activation of alarm input will send alarm SMS and ringing to
predefined phone number. Inputs are blocked for one alarm message per minute.
7
3. Installation
3.1. Definition of Usage, Safety
Before installation, please make sure that using a mobile phone as well as GSM
communicator is not prohibited in the particular type of vehicle!
The communicator is designed for installation on a hidden, protected and dry place in the
vehicle cabin or in the luggage or freight compartment of vehicle. The unit cannot be
exposed to water or any other fluids. Communicator is intended for installation in vehicles
with 12 V or 24 V power system and grounded minus. Connection to power supply must be
protected by a 5 A safety fuse.
Before the installation, disconnect the negative supply pole of vehicle battery (pay attention
to coded car radios). It is recommended to install the antennas and switches first and then
to draw the cables towards the unit. Connect the newly installed cables to the original lines
with a tape.
To connect the connector pins, use only special tools. In case you don’t have such tools,
use soldering.
Do not install the communicator in places with increased level of interfering
electromagnetic radiation such as near a radio transmitter antenna. Avoid installation in
extremely hot places.
8
3.2. Connection drawing
9
3.3. Instructions for Installation
Power supply
Provide constant power supply of 12 or 24 V DC. Peak current can reach up to 2 A,
therefore make sure the power supply wires are connected perfectly. Contact resistance
can cause reset of communication unit and subsequent data transmission failures.
ED 001 006 – GSM antenna
GSM antenna is installed directly into the jack on the communicator. GSM antenna
connector in the sensitive tighten it to prevent its release during the journey.
ED 002 002 – GPS antenna
Install horizontally under the dashboard, under the plastic cover of cabin suction or in the
plastic bumpers. Ensure the best view of the sky – there must be no metal objects in the
view. Be aware of metal coating of glass in some cars – the GPS signal does not pass
through such glass. The proper direction of the antenna towards the sky is marked on the
antenna with an arrow or a notice “face to satellite”.
ED 060 601 – Emergency button
Install to a suitable place in reach of driver and front-seat passenger.
ED 060 613 – Crash sensor
Connect the sensor firmly to the vehicle body with the red arrow directed forward.
ED 060 615 – Trip type switch – private / work
Install to a suitable place within driver’s reach. Switch indicates private trip when in position
with the dot.
ED 060 614 – Immobilization relay
Immobilization relay provides vehicle shutdown – it disconnects the vehicle immobilization
circuit after receiving command SMS. Select the immobilization circuit according to the
vehicle type and connect it to the disconnect contact of ED 060 614.
Alarm inputs
Input 3 is activated by positive pulses from existing vehicle alarm system.
Input 4 is activated by negative pulses se from existing vehicle alarm system.
10
3.4. LED signalling
GSM – yellow LED
0,5 s / 0,5 s
1× short
2× short
No GSM signal or no SIM inserted
GSM connected to network
GSM module + GPRS context connected
GPS – red LED
0,5 s / 0,5 s
1× short
No light
GPS module without signal
GPS module working correctly but without valid data
GPS module has valid data
(only in normal operation mode)
POWER – green LED
2× short / 5 s
1× short / 10s
Normal operation mode
Low power consumption mode (sleep mode)
3.5. Testing SMS
Test whether the installation was done correctly by sending a testing SMS. After the
communicator unit was installed, make a short ride, press the emergency button and
switch the trip type switch. Send the following SMS to the phone number of SIM card in
communicator:
Testing SMS
SMS
Reply
password TEST
default password from production is: picola
TEST
ignition: 0/1 - ignition input
vibr.sens.: 0/1 - vibration sensor
emerg.: 0/1 - emergency button
priv.: 0/1 - trip type switch private/work
GPS: 0/1 - GPS receiver does not / does have valid data
GSM: 0...32 - GSM signal strength in range from 0 to 32*
0 = input or device is not functional
1 = input or device is functional
* GSM signal weaker than 5 is not usable, find better spot for GSM
antenna
11
3.6. Checking Correct Function
Proper operation of all functions of the communicator can be checked by SMS.
Checking power supply
SMS inquiry
Response
Value x
Value y
picola POWER
Power ExtPwr x, y
x = value of external power supply
y = value of external backed-up power supply
Power supply can be checked using the signalization LED on the unit – as described in
chapter LED signalization.
Checking GSM signal
SMS inquiry
Response
Value x
Value y
Value z
Value q
Picola GSM
GSM_x_Credit_y_CellId_z_Signal_q
Name of connected GSM network
Balance of prepaid credit on SIM card
Name of connected GSM cell
Signal strength (0 – 32, 32 = maximum)
GSM signal lower than 5 is not usable, it is necessary to find better place for the GSM
antenna. GSM signal can be checked using the signalization LED on the unit – as
described in chapter LED signalization.
Checking GPS
SMS inquiry
Response
Value t
Value x
Value y
Value q
Value n
Value r
picola GGA
$GPGGA,t,x,y,q,n,r
Time hhmmss.sss h-hours, m-minutes, s-seconds
Latitude coordinates ddmm.mmmm (e.g. 5025.223400,N)
Longitude coordinates ddmm.mmmm (e.g. 01610.090300,E)
Validity of GPS data, 0 = invalid data, 1 = valid data
Number of satellites
Other GPS data
After connecting the power supply of communicator, take the vehicle to a place with good
view of sky, switch the ignition key on and wait for about 5 minutes to get valid GPS data.
Status of GPS can be checked using the signalization LED on the unit. GPS can be
considered fully working when it has valid data and at least 3 satellites.
12
4. Configuration
4.1. SIM, SMS, APN, server
Insert the SIM card in the slot on the front side of the communicator. Eject the SIM by
repeated pressing of SIM. SIM card must not be blocked by PIN, must have enough credit,
erased SMS and activated GPRS data services from the GSM operator.
Basic settings and operation of the unit is done via SMS messages sent to the phone
number inserted in the communication unit in vehicle.
PASSWORD command1 parameter1 command2 parameter2 command3 parameter3 …
PASSWORD Up to 8 characters a-z and 0-9. Default password is “picola”.
space
COMMAND Name of command for required configuration
space
PARAMETER Value, ? for inquiry or . (dot) – to erase value
One SMS message can contain up to 4 commands with parameters. Communicator
confirm executing all commands by confirmation SMS. Small and capital letter make no
difference.
Settings of APN of the GSM operator
Settings SMS
Response
Picola
Value x
Set to x
picola APN x
APN „x“
Default password from production
APN of the GSM operator
Internet
Settings of APN login name – only with some operators
Settings SMS
Response
Value x
Set to x
password GPRSNAME x
gprsname „x“
Login name for APN
-
Settings of APN password – only at some operators
Settings SMS
Response
Value x
Set to x
password GPRSPSW x
gprspsw „x“
Password for APN
-
Settings of server for sending data
Settings SMS
Response
Value x
Value y
Value z
Set to x
Set to y
Set to z
password SERVER @x,y,udp,z
Server.number „@x,y,udp,z“
IP address of server
Port number
0 = disabled in roaming, 1 = enabled
84.233.161.4
32769
0
13
4.2. Password, list of phone numbers, credit
Change of PASSWORD
Settings SMS
Response
Value x
Set to x
password PSW x
psw x
Up to 8 characters a-z and 0-9
picola
Any modification of password must be reported to the administrator of supervision system.
Password is the same for SMS communication as well as communication between the
communicator and the server.
List of phone numbers
Settings SMS
Response
Value x
Value y
Inquiry
Erasure of nr.
password TELx y
Telx.number “y“
1 - Phone number to send alarm SMS from
alarm input 1
2 - Phone number to send alarm call from
alarm input 1
3 - Phone number to send alarm SMS from
alarm input 2
4 - Phone number to send alarm call from
alarm input 2
5 - Phone number to send alarm SMS from
emergency button
6 - Phone number to send alarm call from
emergency button
7 - Phone number to send information SMS
Phone number in international format
Password TELx ?
Password TELx .
Settings of USSD code for prepaid credit amount
Settings SMS
Response
Value x
Set to x
password CREDITCMD x
Creditcmd_“x“
-
-
Settings of low limit of credit
Settings SMS
Response
Value x
Set to x
Password CREDITLOW x
creditlow „x“
Low limit of prepaid credit
0
14
5. Technical Parameters, Maintenance
5.1. Technical parameters
GSM Siemens MC55i (850 / 900 / 1800 / 1900 MHz)
SIM card Plug-in 3 V
GSM antenna connector FME – m
FCC approved
Communication Call, SMS, GSM Data, GPRS
SMS Alarm SMS
SMS inquiry / response
Change of configuration via SMS
Launching action by name of action in SMS
SMS with measured parameters
Up to 4 parameters in one SMS
GSM Data
Modem connection
Configuration editing
Reading of measured values
Reading of events- memory log
Output control
Firmware upgrade
GPRS connection Class 10
Support of static and dynamic IP and VPN network
UDP protocol
Transmission protection by 128bits encryption
All features like in GSM data
GPS 16 channels
Antaris® LH highly sensitive
Accuracy 2,5m CEP
Antenna connector SMB – f
Log file memory EEprom 256 kB i.e. 4000 positions (10k when compressed)
Power supply 10 to 24 V
Power consumption with active GSM and GPS <70mA at 12V
Power consumption in sleep mode <10mA at 12V
5 inputs
2 outputs
Input max. 24 V
Output current max. 0,5 A
Pin 1 Input from ignition key +12 V (+24 V)
Pin 2 Input from emergency button
Reacts to connection with +12 V (+24 V)
Pin 3 Alarm input 1
Reacts to connection with +12 V (+24 V)
Pin 4 Alarm input 2
Reacts to connection with ground
Pin 5 Ground
Pin 6 Not used
Pin 7 Power supply +12 V (+24 V)
Pin 8 +12 V backed-up (not charged from the unit)
15
Pin 9 Trip type switch
Disconnected = work trip
Connected with ground = private trip
Pin 10 Output 1 for external immobilization relay
Output current max. 0,5 A at 12 V
Pin 11 Output 2 for sound signalization
Output current max. 0,5 A at 12 V
Pin 12 Not used
USB Connection to PC
Configuration, firmware upgrade
Real time clock RTC Date and time backed up by battery
Synchronization of time with GPS
Protection class IP 20
Dimensions 69 x 70 x 32 mm
Weight 50 g
Case Plastic
Temperature range Operation temperatures for GSM module: -20 to +55 °C
Operation temperatures for unit: -40 to +85 °C
5.2. Maintenance
The GC 073 MotoMon Communicator requires no special maintenance. We recommend
regular check of external battery at least once a year (just in case the battery is installed).
16
5.3. Troubleshooting
Problem Solution
Power supply 1. Check that GC 073 is connected to power and LED PWR
blinks as described in table – chapter 4.2.
2. Check that GC 073 is connected to constant power source
(not being disconnected – for example when ignition is
switched off)
3. Check that power supply is strong at least 1A /12V
4. Check that connectors are not oxidized.
5. Check the connections of wires that there is no voltage drop
caused by contact resistance there.
SIM card 6. Check that SIM card is inserted correctly in GC 073
7. Check that SIM card is connected into the GSM network –
LED GSM blinking as described in table in chapter 4.2.
8. Check PIN in SIM – it must be disabled or set to 1234
9. Check that SIM card has enough of prepaid credit (if it is a
pre-paid SIM card)
10. Check that GPRS data transmissions are enabled for the SIM
card
11. Check settings of APN by SMS – see table in chapter 4.1.
GPS 12. Check the GPS antenna position – side marked “face to
satellite” or with arrow on the side must be directed towards
the sky and must not be covered by any metal objects
13. Find an open-area space with good view of the sky and switch
GC 073 into the regular operation mode (turn ignition on),
GPS should receive valid data of position within two minutes –
see LED GPS in chapter 4.2.
14. Other information about GPS signal can be received by SMS –
see chapter 3.6.
17
Warranty conditions
The manufacturer provides 24 months of warranty, starting from date of sale.
Warranty repair will be done within 10 working days after delivery of faulty unit to MotoMon
provided all spare parts are in stock. If not, the customer will be offered an alternative
solution.
Warranty repairs will be carried out in the manufacturer facility and the warranty repair is
prolonged by the time of repair duration. Shipping back is determined by a service
technician.
Warranty cannot be provided in case of loss or replacement of warranty certificate, when
product is damaged by natural disaster, during transportation, unsuitable placement,
improper use, using product in unfit conditions and also by breaking or removal of warranty
seal.
The warranty does not cover the expendable supplies – batteries, coloring tape, etc. The
warranty does not cover faults caused by installed software or its impact. The company
does not bear liability for losses caused to user by device fault.
The warranty does not apply to faults caused by changing external conditions, such as
legislature changes, GSM network modifications, changes of power supply conditions, etc.
Warranty must be claimed by presentation of completely filled-in warranty certificate and
device for repair including accessories.
Duplicate of warranty certificate cannot be issued, the customer is responsible for its
correctness and origin.
Warranty certificate
Product name : Type :
Serial number : Date of sale :
Distributor :
Address, telephone, stamp :
Signature :
Accepted for repair Date of sending Problem description
18
Declaration of Conformity:
Complies with the essential requirements of GSM module: FCC identifier QIPMC55i
IC: 267W-MC55i granted to Siemens AG.
19
GC 073 431 F @ 1.01 © 2008
MotoMon Ltd.
20
Loading...