Series HMI Connection Manual
Mitsubishi Q Series Ethernet
Supports QJ71E71 / QJ71E71-B2 / QJ71E71-B5 / QJ71E71-100 Series Module
HMI Factory Setting:
Baud rate: 192.168.0.1
Controller Station Number: 1025
Control Area / Status Area: D0 / D10
Connection
Standard jumper Cable/ Network Cable without jumper (Auto-detected by HMI)
Definition of PLC Read/Write Address |
|
|
|
|
|
a. Registers |
|
|
|
|
|
Type |
Format |
Read/Write Range |
|
|
Note |
|
|
||||
Word No. (n) |
|
|
|||
|
|
Word |
|
||
Input |
Xn |
X0 – X1FF0 |
Hexadecimal, |
||
|
|
|
|
|
2 |
Output |
Yn |
Y0 – Y1FF0 |
Word |
Hexadecimal, |
|
|
|
|
|
|
2 |
Internal Relay |
Mn |
M0 – M8176 |
Word |
2 |
|
Special Internal Relay |
Mn |
M9000 – M9240 |
Word |
3 |
|
Link Relay |
Bn |
B0 – B1FF0 |
Word |
Hexadecimal, |
|
|
|
|
|
|
2 |
Annunciator |
Fn |
F0 – F2032 |
Word |
2 |
|
Timer Value |
TNn |
TN0 – TN2047 |
Word |
|
|
Counter Value |
CNn |
CN0 – CN2047 |
Word |
|
|
Data Register |
Dn |
D0 – D8191 |
Word |
|
|
Special Data Register |
Dn |
D9000 – D9255 |
Word |
|
|
Link Register |
Wn |
W0 – W1FFF |
Word |
Hexadecimal |
|
b. Contacts |
|
|
|
|
|
Type |
Format |
Read/Write Range |
|
Note |
|
Bit No. (b) |
|
||||
|
|
|
|
|
|
Input |
Xb |
X0 – X1FFF |
|
|
Hexadecimal |
134 |
V1.01 Revision November, 2011 |
Series HMI Connection Manual
Output |
Yb |
Y0 – Y1FFF |
Hexadecimal |
|
Internal Relay |
Mb |
M0 – M8191 |
|
|
Special Internal Relay |
Mb |
M9000 – M9255 |
|
|
|
|
|
|
|
Type |
Format |
Read/Write Range |
Note |
|
Bit No. (b) |
||||
|
|
|
||
Link Relay |
Bb |
B0 – B1FFF |
Hexadecimal |
|
Annunciator |
Fb |
F0 – F2047 |
|
|
Timer Contact |
TSb |
TS0 – TS2047 |
|
|
Timer Coil |
TCb |
TC0 – TC2047 |
|
|
Counter Contact |
CSb |
CS0 – CS2047 |
|
|
Counter Coil |
CCb |
CC0 – CC2047 |
|
NOTE
1)Before using this communication protocol, the user needs to set communication module via GX Developer programming tools. For more detailed information regarding the setting method, please refers to Mitsubishi PLC User Manual.
2)The device address must be the multiple of 16.
3)The device address must be the multiple of 16 plus 9000.
V1.01 Revision November, 2011 |
135 |