Mitsubishi Electronics N0701 User Manual

0 (0)
For future reference, record the serial
number of your display monitor in the
space below:
SERIAL No.
The serial number is located on the
rear cover of the monitor.
AUTO-SCANNING WITH DIGITAL CONTROL
COLOR DISPLAY MONITOR
USER'S MANUAL
IBM is registered trademark of International Business Machines Corporation
Apple and Macintosh are registered trademarks of Apple Computer Inc.
Microsoft and Windows are registered trademarks of the Microsoft Corporation.
ENERGY STAR is a U.S. registered mark.
All other trademarks or registered trademarks are property of their respective owners.
ENERGY STAR
®
Product
As an ENERGY STAR Partner, NEC-Mitsubishi Electronics Display has determined
that this product meets the ENERGY STAR guidelines for energy efficiency. The
ENERGY STAR emblem does not represent EPA endorsement of any product or
service.
RADIO INTERFERENCE REGULATIONS STATEMENT FOR U.S.A.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NO USER SERVICEABLE PARTS INSIDE. DO NO ATTEMPT TO
MODIFY THIS EQUIPMENT. IF MODIFIED, YOUR AUTHORITY TO
OPERATE THIS EQUIPMENT MIGHT BE VOIDED BY FCC.
Declaration of Conformity-United States only
Product Name: 17in.(43cm)Color Display Monitor
Type: N0701
Brand Name: MITSUBISHI
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
U.S Responsible party: NEC-Mitsubishi Display of America,Inc.
Adress: 1250 N. Arlington Heights Road
ltasca, illinois 60143
Tel. No.: (630)467-3000
To identify this product, refer to the model number found on the product.
T-1
TCO'99
Congratulations!
You have just purchased a TCO’99 approved and
labelled product! Your choice has provided you with
a product developed for professional use. Your
purchase has also contributed to reducing the burden
on the environment and also to the further
development of environmentally adapted electronics
products.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established
method for encouraging the adaptation of goods and services to the
environment. The main problem, as far as computers and other electronics
equipment are concerned, is that environmentally harmful substances are
used both in the products and during their manufacture. Since it is not so
far possible to satisfactorily recycle the majority of electronics equipment,
most of these potentially damaging substances sooner or later enter
nature.
There are also other characteristics of a computer, such as energy
consumption levels, that are important from the viewpoints of both the
work (internal) and natural (external) environments. Since all methods of
electricity generation have a negative effect on the environment
(e.g.acidic and climate-influencing emissions, radioactive waste), it is vital
to save energy. Electronics equipment in offices is often left running
continuously and thereby consumes a lot of energy.
What does labelling involve?
This product meets the requirements for the TCO’99 scheme which
provides for international and environmental labelling of personal
computers. The labelling scheme was developed as a joint effort by the
TCO (The Swedish Confederation of Professional Employees), Svenska
Naturskyddsforeningen (The Swedish Society for Nature Conservation)
and Statens Energimyndighet (The Swedish National Energy
Administration).
Approval requirements cover a wide range of issues: environment,
ergonomics, usability, emission of electric and magnetic fields, energy
consumption and electrical and fire safety.
The environmental demands impose restrictions on the presence and use
of heavy metals, brominated and chlorinated flame retardants, CFCs
(freons) and chlorinated solvents, among other things. The product must
T-2
be prepared for recycling and the manufacturer is obliged to have an
environmental policy which must be adhered to in each country where the
company implements its operational policy.
The energy requirements include a demand that the computer and/or
display, after a certain period of inactivity, shall reduce its power
consumption to a lower level in one or more stages. The length of time to
reactivate the computer shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example,
in respect of the reduction of electric and magnetic fields, physical and
visual ergonomics and good usability.
Below you will find a brief summary of the environmental requirements
met by this product. The complete environmental criteria document may
be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): development@tco.se
Current information regarding TCO’99 approved and labelled
products
may also be obtained via the Internet, using the address:
http://www.tco-info.com/
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires,
casings and housings. Their purpose is to prevent, or at least to delay the
spread of fire. Up to 30% of the plastic in a computer casing can consist
of flame retardant substances. Most flame retardants contain bromine or
chloride, and those flame retardants are chemically related to another
group of environmental toxins, PCBs. Both the flame retardants containing
bromine or chloride and the PCBs are suspected of giving rise to severe
health effects, including reproductive damage in fish-eating birds and
mammals, due to the bio-accumulative* processes. Flame retardants have
been found in human blood and researchers fear that disturbances in
foetus development may occur.
The relevant TCO’99 demand requires that plastic components weighing
more than 25 grams must not contain flame retardants with organically
bound bromine or chlorine. Flame retardants are allowed in the printed
circuit boards since no substitutes are available.
T-3
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-
generating layers of certain computer displays. Cadmium damages the
nervous system and is toxic in high doses. The relevant TCO’99
requirement states that batteries, the colour-generating layers of display
screens and the electrical or electronics components must not contain any
cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. It damages
the nervous system and is toxic in high doses. The relevant TCO’99
requirement states that batteries may not contain any mercury. It also
demands that mercury is not present in any of the electrical or electronics
components associated with the labelled unit.
CFCs (freons)
The relevant TCO’99 requirement states that neither CFCs nor HCFCs may
be used during the manufacture and assembly of the product. CFCs
(freons) are sometimes used for washing printed circuit boards. CFCs
break down ozone and thereby damage the ozone layer in the
stratosphere, causing increased reception on earth of ultraviolet light with
e.g. increased risks of skin cancer (malignant melanoma) as a
consequence.
Lead**
Lead can be found in picture tubes, display screens, solders and
capacitors. Lead damages the nervous system and in higher doses, causes
lead poisoning. The relevant TCO’99 requirement permits the inclusion of
lead since no replacement has yet been developed.
* Bio-accumulative is defined as substances which accumulate within
living organisms.
** Lead, Cadmium and Mercury are heavy metals which are
Bio-accumulative.
English
Deutsch
Français
Español
Italiano
E
E-1
Monitor box* should contain the following:
* Remember to save your original box and packing material to transport
or ship the monitor.
* Complete and mail in warranty card. (for North America)
Color Monitor Diamond Plus 73
Warranty card (for North America)
Questionnaire card (for North America)
User‘s manual
Power cord (Put only one Type)
Contents
CAUTION
The power cord provided with this monitor is
designed for safety and must be used with a properly
grounded outlet to avoid possible electrical shock.
Do not remove the monitor cabinet as this can expose
you to very high voltages and other hazards.
MANUFATURER DECLARATION
FOR CE-MARKING:
We, NEC-Mitsubishi Electric Vi s u a l
Systems Corporation, declare under our
sole re s p o n s i b i l i t y, that this product is in
c o n f o rmity with the following standard s :
EN60950
EN55022(Class B)
EN61000-3-2
EN61000-3-3
EN55024
(IEC61000-4-2)
(IEC61000-4-3)
(IEC61000-4-4)
(IEC61000-4-5)
(IEC61000-4-6)
(IEC61000-4-8)
(IEC61000-4-11)
following the provisions of:
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
WARNING!
This product is not designed for use in life support
devices and
NEC-Mitsubishi Electric Visual Systems
C o r p o r a t i o n
makes no representations to the contrary.
Life support devices are those devices which are used
to measure, diagnose, or evaluate the tissue, systems
or functions of the human body; or other devices
employed to support or sustain life or good health.
UL/CSA (or) Europe (or) UK
E-2
Quick Start
To attach the Monitor to your system, follow
these instruction:
1 Turn off the power to your computer and the monitor.
2 If necessary, install the display card. For more information, refer to the
display card manual.
3 For the PC: Connect the 15-pin mini D-SUB of the captive signal
cable to the connector of the display card in your system (Figure A.1)
Tighten all screws.
For the Mac: Connect the Macintosh Cable Adapter (not included)
to the monitor connector on the Macintosh (Figure B.1). Attach the 15-
pin mini D-SUB end of the captive signal cable to the Macintosh cable
adapter on the computer (Figure B.1). Tighten all screws.
4 Connect one end of the power cord to the monitor and the other end to
the power outlet (Figure C.1).
5 Turn on the monitor (Figure D.1) and the computer.
6 This completes the installation.
NOTE: If you have any problems, please refer to the
Troubleshooting section of this User's Manual.
Captive Signal Cable
15-pin-mini-D-SUB
Figure A.1
E
E-3
Captive Signal Cable
Computer
Power Outlet
Power cord
Mac Adapter
(not included)
*For Mac Adapter
contact your dealer
15-pin mini D-SUB
Figure B.1
Figure C.1
Figure D.1
CAUTION:
The socket-outlet shall be installed near
the equipment and shall be easily
accessible. During servicing, disconnect
the plug from the socket-outlet.
E-4
Controls
OSD(On-screen Display) control buttons on the
front of the monitor function as follows:
SELECT Enters and exits the OSD menu.
-/+ Selects one of the controls and decreases or increases the
adjustment.
RESET Resets the highlighted control to the factory setting.
Press -/+ button at the same time for approximately 1 sec.
Brightness: Adjusts the overall image and background
screen brightness.
Contrast: Adjusts the image brightness in relation to the
background.(Contrast control is also effective with “-,+”
button even though OSD window is not visible.)
R Red Color Control: Adjust the red contrast of the display.
G Green Color Control: Adjust the green contrast of the
display.
B Blue Color Control: Adjust the blue contrast of the display.
Horizontal: Moves the image horizontally left or right.
Vertical position: Moves the image vertically up or down.
Horizontal size: Decreases or increases the horizontal size
of the image.
Vertical size: Decreases or increases the vertical size of the
image.
The Geometry controls allow you to adjust the curvature or angle of the
sides of your display.
E
E-5
Pincushion/Barrel: Decreases or increases the curvature
of the sides either inward or outward.
Trapezoid: Decreases or increases the bottom of the screen
to be the same as the top.
Parallelogram: Decreases or increases the tilt of the sides
either to the left or right.
Bow (Pincushion Balance): Decreases or increases the
curvature of the sides either to the left or right.
Rotates: Rotates the image.
Degauss: Select the degauss icon on “Icon select window”
and push “SELECT” button.
It will eliminate the stray magnetic field and correct the scan
of the electron beam, which affect the purity, focus and
convergence.
Note: Allow a minimum interval of 20 minutes to elapse
between uses of the degauss function.
9300K Color Temperature: Select the Color Temperature icon on
“Icon Select Window” and push “SELECT” button.
OSD: There are 3 background colours (Blue, Black, and
white). These can be selected by “SELECT” button after the
selection of “OSD” on ”Icon select window”.
exit EXIT: To exit OSD window. Select EXIT on “Icon select
window”, then push “SELECT” button.
Note:If you do not push buttons within 10 seconds in OSD
condition, the window will automatically disappear.
E-6
Recommended use
Safety Precautions and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE
FOLLOWING WHEN SETTING UP AND USING
THE COLOR MONITOR:
DO NOT OPEN THE MONITOR. There are no user serviceable
parts inside and opening or removing covers may expose you to
dangerous shock hazards or other risks. Refer all servicing to
qualified service personnel.
Use the monitor in a clean, dry area.
Do not spill any liquids into the cabinet or use your monitor near
water.
Do not insert objects of any kind into the cabinet slots, as the may
touch dangerous voltage points, which can be harmful or fatal or
may cause electric shock, fire or equipment failure.
Do not place any heavy objects on the power cord. Damage to the
cord may cause shock or fire.
Do not place this product on a sloping or unstable cart, stand or
table, as the monitor may fall, causing serious damage to the
monitor.
Keep the monitor away from high capacity transformers, electric
monitors and other devices such as external speakers or fans, which
may create strong magnetic fields.
If possible, position the monitor so that it is facing the east to
minimize the effects of the earth‘s magnetic field.
Changing the direction of the monitor while it is powered on may
cause image discoloration. To correct this, turn the monitor off for 20
minutes before powering it back on.
To separate the equipment from the power source you have to
remove the plug from the inlet socket.
• When operating the Diamond Plus 73 with its AC 220-240V
worldwide power supply, use a power supply cord that matches the
power supply voltage of the AC power outlet being used. The power
supply cord you use must have been approved by and comply with
the safety standards of your country.
Immediately unplug your monitor from the wall outlet and refer servicing
to qualified service personnel under the following conditions:
When the power supply cord or plug is damaged.
If liquit has been spilled, or objects have fallen into the monitor.
If the monitor has been exposed to rain or water.
If the monitor has been dropped or the cabinet damaged.
E
E-7
If the monitor does not operate normally by following operating
instructions.
Allow adequate ventilation around the monitor so
that heat can properly dissipate. Do not block
ventilated openings or place them monitor near a
radiator or other heat sources. Do not put an thing
on top of monitor.
The power cable connector is the primary means of
detaching the system from the power supply. The
monitor should be installed close to a power outlet
which is easily accessible.
Handle with care when transporting.
Save packaging for transporting .
CORRECT PLACEMENT AND ADJUSTMENT OF THE
MONITOR CAN REDUCE EYE, SHOULDER AND NECK
FATIGUE. CHECK THE FOLLOWING WHEN YOU •
POSITION THE MONITOR:
CAUTION
Adjust the monitor height so that the top of the screen is at or slightly
below eye level. Your eyes should look slightly downward when
viewing the middle of the screen.
Position your monitor no closer than 40 cm and no further away
than 70 cm from your eyes. The optimal distance is 50 cm.
Rest your eyes periodically by focusing on an object at least 6 m
away. Blink often.
• Position the monitor at a 90˚ Xangle to windows and other light
sources to minimize glare and reflections. Adjust the monitor tilt so
that ceiling lights do not reflect on your screen.
E-8
If reflected light makes it hard for you to see your screen, use an
anti-glare filter.
Adjust the monitorís brightness and contrast controls to enhance
readability.
Use a document holder placed close to the screen.
Position whatever you are looking at most of the time (the screen or
reference material) directly in front of you to minimize turning your
head while you are typing .
Get regular eye checkups.
Cleaning Your Monitor
When cleaning the monitor, please follow these guidelines:
Always unplug the monitor before cleaning.
Wipe the screen and cabinet front and sides with a soft cloth.
If the screen requires more than dusting, apply a household window
cleaner to a soft cloth to clean the monitor screen.
Do not use benzene, thinner or any volatile
substances to clean the unit as the finish may be
permanently marked.
Never leave the monitor in contact with rubber or
vinyl for an extended time period.
Do not spray directly on the screen as cleaner may
drip into the monitor and damage the circuitry.
Never use an abrasive cleaner on the screen
surface as this will damage the anti-reflection
coating.
Ergonomics
To realize the maximum ergonomics benefits, we recommend the
following :
Adjust the brightness until the background raster disappears .
Do not position the contrast controls to its maximum setting .
Use the preset size and position controls with standard signals .
Use the preset color setting and sides Left / Right controls.
Use non-interlaced signals with a vertical refresh rate between
75-120Hz.
Do not use primary color blue on a dark background, as it is
difficult to see and may produce eye fatigue due to insufficient
contrast.
CAUTION
E
E-9
Specifications
Monitor
Specifications
Picture Tube Diagonal :
Viewable Image Size:
Radius:
Input Signal Video:
Sync:
Display Colors Analog input:
Synchronization Horizontal:
Range Vertical:
Resolutions Supported
Resolution based on horizontal
and vertical frequencies only
Active Display Area Horizont:
(Factory setting) Vertical:
Active Display Area
(Full scan)
Power Supply
Current Rating
Dimensions
Weight
Environmental Considerations
Operating Temperature:
Humidity:
Altitude:
Storage Temperature:
Humidity:
Altitude:
NOTE: Technical specifications are subject to change without notice.
Diamond Plus 73
Monitor
43cm(17inch)
41cm(16inch)
50000mm
ANALOG 0.7 Vp-p/75 Ohms
Separate sync. TTL Level
Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Unlimited number of Colors
31kHz to 70kHz
55Hz to 120Hz
640 x 480 @60 to 120Hz
800 x 600 @55 to 110Hz
832 x 624 @55 to 105Hz
1024 x768 @55 to 87Hz....
1280 x 1024 @55 to 66Hz
310mm
232mm
325mm
243mm
AC 100-240V, 50-60Hz
1.5A @ 100-240V
403(W)x420(H)x420(D)mm
16.4kg
0˚C to +35˚C
30% to 80%
0 to 3000m
-20˚C to + 60˚C
10% to 90%
0 to 13700m
Notes
90˚ deflection, 0.25mm grille pitch,
medium short persistence phosphor,
aperture grille CRT, multi-layered, anti-
staticscreen coating, dark-tint screen.
Depends on the display card used.
Automatically
Automatically
Some systems may not support all
modes listed
Recommended resolution at 85 Hz for
optimal display performance.
Dependent upon signal timing used,
and does not include border area.
Dependent upon signal timing used,
and does not include border area.
E-10
Features
Flat Aperture Grille CRT:
Delivers an unparalleled viewing experience with a virtually flat image,
eliminating distortion and reducing glare so that what you see on-screen is
what you get on your printed output. The striped phosphor alignment of the
CRT delivers superior vertical definition with improved brightness for more
uniform image contrast.
Screen Surface
:
Reduces reflection and glare and increases contrast without sacrificing
focus level, clarity or brightness. Along with the flat square technology
CRT, a high contrast screen with 0.25 mm grille pitch delivers crisp, clean
text and graphics.
Dual Dynamic Beam Focus :
Provides precise, continuous focus adjustment of the electron beams and
optimum image quality, even to the far edge of the screen.
Color Control System: Allows you to change between five color
settings on your display to match your personal preference.
OSD(On-Screen Display) Controls: Allow you to quickly and
easily adjust all elements of your screen image via simple to use on-
screen menus.
Ergonomice Features: Enhance human ergonomics to improve the
working environment, protect the health of the user and save money and
is compliant with TCO'99 and MPRII for lower emissions .
Plug and Play: The Microsoft
®
solution with the Windows
®
95/98
operating system facilitates setup and installation by allowing the monitor
to send its capabilities (such as screen size and resolutions supported)
directly to your computer, automatically optimizing display performance.
Power Management System: Provides innovative power-saving
methods that allow the monitor to shift to a lower power consumption
level when on but not in use, saving your monitor energy costs, reducing
emissions and lowering the air conditioning costs of the workplace and is
compliant with VESA DPMS and EPA ENERGY STAR
®
.
Mode LED Indicator Power Saving
On Green None
Off (IPM Mode) Orange Maximum(<5 Watts, Slow Recovery)
Off(Power Switch, Off) No Light No Power Used(Fully Off)
E
E-11
Reduced Magnetic Field Technology: Reduces magnetic and
alternating electric field emissions and static electricity, addressing
ergonomic concerns regarding potential risks from extended computer
monitor use and is compliant with MPRII and TCO‘99.
Multiple Frequency Technology: Automatically adjusts monitor
to the display card‘s scanning frequency, thus displaying the resolution
required.
FullScan Capability: Allows you to use the entire screen area in
most resolutions, significantly expanding image size.
E-12
Troubleshooting
No Picture
The display card should be completely seated in its slot.
Power Switch and computer power switch should be in the ON
position.
The signal cable should be completely connected to the display
card/computer.
Check the connector for bent or pushed-in pins.
Image is scrolling or unstable
Signal cable should be completely attached to the computer.
Check the pin assignment and signal timing of your monitor and
display card with respect to the recommended timing and pin
assignment .
If the MAC adapter is used, check for proper connection or make
sure the display card is MAC compatible and that the card is
properly seated in the computer.
LED on the monitor is not lit
(no green or orange color can be seen)
Power Switch should be in the ON position and the power cord
should be connected.
Picture is fuzzy or Color looks blotchy
Adjust the Brightness and Contrast Controls.
Access the Degauss Control through OSD.
Activate the Degauss Control.
CAUTION: A minimum interval of 20 minutes should exist before the
Degauss Function is used a second time.
P i c t u re bounces or a waving pattern is present in the picture
Move electrical devices that may be causing electrical interference
away from the monitor.
Edges of the display image are not square
Use the OSD Geometry Controls to straighten the edges.
If possible, position the front of the monitor facing east.
Display image is not centered, too small, or too large
Use the OSD Size and Position controls to adjust the image.
E
E-13
Black vertical lines are visible on the screen
Thin vertical black lines on one or both sides of the screen. This
minor condition is caused by grille element overlap which can occur
during shipping.
Position an open white window over the affected area of the screen
and maximize the brightness and contrast controls. This will cause
localized heating of the overlap which will clear in a few minutes. Be
sure to readjust the brightness and contrast controls back to the
normal viewing level after this procedure.
Two fine horizontal lines are visible on the screen
The 2 very faint thin lines across the screen are normal. They are
caused by the aperture grille stabilization filaments(Damper
Wires)which are required for all aperture grille CRTs'.
A buzzing sound when power on
A brief vibration or hum sound that is heard just after power up is
normal. This is caused by the automatic degaussing function. This
sound will be heard each time the monitor is powered up from a
cold start and each time the manual degauss button is used.
Shadow of Damper Wires
Aperture Grille Type
Electron Gun
Damper Wires
Shadow of
Damper Wires
Aperture Grille
Röntgenstrahlung
Die in diesem Gerät erzeugten Röntgenstrahlen sind durch die
eigensichere Kathodenstrahlröhre ausreichend abgeschirmt.
Unsachgemäße Eingriffe, insbesondere Verändern der Hochspannung
oder Einbau eines anderen Bildröhrentyps, können dazu führen, daß
Röntgenstrahlung in erheblicher Stärke auftritt. So veränderte Geräte
entsprechen nicht mehr dieser Zulassung und dürfen nicht betrieben
werden.
D
D-1
Lieferumfang
Monitor Karton* sollte folgendes enthalten sein:
* Bewahren Sie die Originalverpackung für einen möglichen Transport
oder Versand des Geruätes unbedingt auf.
Monitor
Bedienerhandbuch
Netzkabel
ACHTUNG
Das mitgelieferte Netzkabel wurde konzipiert, um
größtmögliche Sicherheit zu gewährleisten. Es darf
nur an eine ordnungsgemäß geerdete Steckdose
angeschlossen werden, um eventuelle Stromschläge
zu vermeiden.
Entfernen Sie nie die Rückwand dieses Gerätes, da
Sie sich dadurch sehr hohen Spannungen und
anderen Gefahren aussetzen können.
HERSTELLER-
KONFORMITÄTSERKLÄRUNG
ZUR CE-KENNZEICHUNUNG:
Wi r, NEC-Mitsubishi Electric Vi s u a l
Systems Corporatation, erklären in
alleiniger Verantworlung, daß das
P rodukt auf das sich diese Erkläru n g
bezieht, mit der/den folgenden
N o rmen oder norm a t i v e n
Dokumenten übere i n s t i m m t :
EN60950
EN55022(Klasse B)
E N 6 1 0 0 0 - 3 - 2
E N 6 1 0 0 0 - 3 - 3
EN55024
(IEC61000-4-2)
(IEC61000-4-3)
(IEC61000-4-4)
(IEC61000-4-5)
(IEC61000-4-6)
(IEC61000-4-8)
(IEC61000-4-11)
Gemäß den Bestimmungen der
R i c h t l i n i e n :
7 3 / 2 3 / E E C
N i e d e r s p a n n u n g s r i c h t l i n i e
89/336/EEC EMV Richtlinie
ACHTUNG!
Dieses Produkt ist nicht für den Gebrauch in
Zusammenhang mit lebenserhaltenden Geräten
geeignet und die NEC-Mitsubishi Electric Visual Systems
C o r p o r a t a t i o n macht keinerlei gegensätzliche
Darstellungen. Lebenserhaltende Geräte sind solche,
die zum Messen, Diagnostizieren oder für die
Auswertung von Gewebe, Systemen oder Funktionen
des menschlichen Körpers benutzt werden; oder
andere Geräte die angewendet werden, um das
Leben oder die Gesundheit zu unterstützen oder zu
erhalten.
UL/CSA (oder) Europa (oder) UK
D-2
Inbetriebnahme
Beim Anschluß eines Monitors an Ihren Computer
sind folgende Punkte zu beachten:
1 Schalten Sie die Stromversorgung von Computer und Monitor aus.
2 Falls notwendig, installieren Sie eine Grafikkarte nach den
Anweisungen im Benutzerhandbuch der Grafikkarte.
3 Für den PC: Verbinden Sie den 15-pin mini D-SUB Stecker des fest
montierten Signalkabels mit der entsprechenden Buchse der
Grafikkarte Ihres Rechners (Abbildung A.1). Ziehen Sie alle Schrauben
fest.
Für den Macintosh: Stecken Sie den Macintosh Signaladapter
(Option) auf die entsprechende Buchse der Grafikkarte des Macintosh
(Abbildung B.1). Stecken Sie den 15-pin mini D-SUB Stecker des fest
montierten Signalkabels auf den Adapter am Rechner (Abbildung B1).
Ziehen Sie alle Schrauben fest.
4 Verbinden Sie das mitgelieferte Netzkabel auf einer Seite mit dem
Monitor und auf der anderen Seite mit einer geerdeten Wandsteckdose
in der Nähe des Monitor (Abbildung C.1).
5 Schalten Sie Monitor (Abbildung D.1) und Computer ein.
6 Hiermit ist der Anschluß des Monitors abgeschlossen.
Hinweis: Sollten sich hierbei Probleme ergeben, so lesen Sie bitte den
Abschnitt “Hilfe bei Problemen”.
Fest montiertes Signalkabel
15-pin mini D-SUB
Abbildung A.1
Loading...
+ 56 hidden pages