Loading...
For A Ethernet
Interface Module
User’s Manual
(Hardware)
AJ71E71N-B5T, A1SJ71E71N-B5T AJ71E71N-B2, A1SJ71E71N-B2
Thank you for buying the Mitsubishi general-purpose programmable logic
controller MELSEC-A Series
Prior to use, please read both this manual and detailed manual thoroughly and familiarize yourself with the product.
MODEL E71N-U-HW
MODEL 13JT70
CODE
IB (NA)-0800203-A (0201) MEE
2002 MITSUBISHI ELECTRIC CORPORATION
! SAFETY PRECAUTIONS !
(Always read before starting use)
When using Mitsubishi equipment, thoroughly read this manual and the associated manuals introduced in the manual. Also pay careful attention to safety and handle the module properly.
These precautions apply only to the installation of Mitsubishi equipment and the wiring with the external device. Refer to the user’s manual of the CPU module to be used for a description of the PLC system safety precautions.
These 
SAFETY PRECAUTIONS 
classify the safety precautions into two categories:
"DANGER" and "CAUTION".
DANGER
CAUTION
Procedures which may lead to a dangerous condition and cause death or serious injury if not carried out properly.
Procedures which may lead to a dangerous condition and cause superficial to medium injury, or physical damage only, if not carried out properly.
Depending on circumstances, procedures indicated by 
CAUTION may also be linked to serious results.
In any case, it is important to follow the directions for usage.
Store this manual in a safe place so that you can take it out and read it whenever necessary. Always forward it to the end user.
[DESIGN PRECAUTIONS]
CAUTION
!When laying the control wire or communication cable, do not bundle with or place near main circuit or power line.
Keep them at least 100 mm (3.94 in.) away from such cables. Noise may cause erroneous operation.
[INSTALLATION PRECAUTIONS]
CAUTION
!Use the PLC in the environment given in the general specifications section of the user's manual to be used. Using the PLC outside the range of the general specifications may result in electric shock, fire, or erroneous operation or may damage or degrade the product.
A- 1
[INSTALLATION PRECAUTIONS]
CAUTION
!Install so that the tabs at the bottom of the module fit securely into the base unit mounting holes. (The AnS series module shall be fastened by screws in the base unit at the specified torque.)
Not installing the module correctly could result in erroneous operation, damage, or pieces of the product falling.
!Tighten the screw within the range of specified torque.
If the screws are loose, it may result in fallout, short circuits or malfunction. Tightening the screws to far may cause damage to the screw and/or the module, resulting in fallout, short circuits or malfunction.
!Make sure to switch all phases of the external power supply off before mounting or removing the module.
If you do not switch off the external power supply, it will cause electric shock or damage to the product.
!Do not touch the electronic parts or the module conducting area directly.
It may cause erroneous operation or failure.
[WIRING PRECAUTIONS]
CAUTION
!Perform correct pressure-displacement, crimp-contact or soldering for external wire connections using the tools specified by the manufactures. Incorrect connection may cause short circuits, fire or malfunction.
!Attach connector to the module securely.
!Be sure to fix communication cables or power supply cables leading from the module by placing them in the duct or clamping them. Cables not placed in the duct or without clamping may hang or shift, alllowing them to be accidentally pulled, which may cause a module malfunction and cable damage.
!Tighten the screw within the range of specified torque.
If the screws are loose, it may result in short circuits or malfunction.
Tightening the screws to far may cause damage to the screw and/or the module, resulting in fallout, short circuits or malfunction.
!Do not grab on the cable when removing the communication cable connected to the module.
When removing the cable with a connector, hold the connector on the side that is connected to the module.
When removing the cable connected to the terminal block, first loosen the screws on the part that is connected to the terminal block.
Pulling the cable that is still connected to the module may cause a malfunction or damage to the module or cable.
!Solder coaxial cable connectors properly.
Insufficient soldering may cause malfunction.
!Be sure that cuttings, wire chips, or other foreign matter do not enter the module.
Foreign matter may start a fire or cause an accident or erroneous operation.
A- 2
Revisions
The manual number is given on the bottom left of the back cover.
Print Date |
Manual Number |
Revision |
Jan., 2002 |
IB(NA)-0800203-A |
First printing |
|
|
|
This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual.
2002 MITSUBISHI ELECTRIC CORPORATION
A- 3
CONTENTS 
1. |
Overview............................................................................................................................. |
1 |
|
2. |
Performance Specifications................................................................................................ |
2 |
|
3. |
Settings and Names of Each Part ...................................................................................... |
4 |
|
4. |
Loading and Installation...................................................................................................... |
8 |
|
|
4.1 |
Handling Precautions ................................................................................................... |
8 |
|
4.2 |
Installation Environment ............................................................................................... |
8 |
5. |
Connection to a Network .................................................................................................... |
9 |
|
|
5.1 |
Connecting to the 10BASE-T (AJ71E71N-B5T, A1SJ71E71N-B5T).......................... |
10 |
|
5.2 |
Connecting to the 10BASE5 (AJ71E71N-B5T, A1SJ71E71N-B5T) ........................... |
10 |
|
5.3 |
Connecting to the 10BASE2 (AJ71E71N-B2, A1SJ71E71N-B2)................................ |
10 |
6. |
External Dimensions......................................................................................................... |
11 |
|
A- 4
About the Manuals
The following product are available for this equipment.
Refer to the table given below to choose suitable manuals.
Related Manual
Manual name |
Manual No. |
|
(Model code) |
||
|
||
For A Ethernet Interface Module User’s Manual |
SH-080192 |
|
(13JR45) |
||
|
Conformation to the EMC Directive and Low Voltage Instruction
For details on making Mitsubishi PLC conform to the EMC directive and low voltage instruction when installing it in your product, please refer to Chapter 3, "EMC Directive and
Low Voltage Instruction" of the User's Manual (Hardware) for the CPU module to use. The CE logo is printed on the rating plate on the main body of the PLC that conforms to the EMC directive and low voltage instruction.
For information about conforming this product to the EMC directive and low voltage instruction, please refer to Chapter 3 "EMC Directive and low Voltage Instruction," section
"3.1.3. Cable" of the User's Manual (Hardware) for the CPU module to use.
A- 5
Loading...