Miele Classic C1 Titan, Classic C1 HomeCare, Classic C1 Delphi Operating and Installation Instructions

0 (0)

en Operating Instructions Vacuum Cleaner

fr Instructions d'utilisation Aspirateur

Classic C1

HS12

M.-Nr. 10 090 390

Only Miele FilterBags, filters and accessories with the "Original Miele" logo can be used with this vacuum. Only then can the suction power of the vacuum cleaner reach its optimum potential creating the best possible cleaning results.

USE OF NON-MIELE COMPONENTS MAY VOID THE WARRANTY.

The use of FilterBags made of paper or a similar material, or FilterBags with a cardboard retaining plate can lead to serious damage to the vacuum cleaner and may void the warranty, just as with the use of FilterBags without the "Original Miele" logo.

The "Original Miele" Logo will appear on the packaging or directly on the FilterBag.

Purchasing new FilterBags and filters

Original Miele FilterBags and filters can be purchased from an authorized Miele vacuum dealer or by visiting the Miele store at www.mieleusa.com.

en - Contents

IMPORTANT SAFETY INSTRUCTIONS

Guide to the vacuum cleaner

Before using the vacuum cleaner

Using the Powerbrush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Using the standard floor brush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Included accessories

Use

Power cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Adjusting the Electro Telescopic suction wand. . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Turning the vacuum On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Adjusting the suction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Turning the Powerbrush On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Parking, transport and storage

Maintenance and care

Purchasing new FilterBags and filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Which FilterBags and filters are the right ones? . . . . . . . . . . . . . . . . . . . . . . . . . . 14 When to change the FilterBag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Replacing the FilterBag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 When to change the dust compartment filter (Pre-motor filter) . . . . . . . . . . . . . . 15 Replacing the dust compartment filter (Pre-motor filter) . . . . . . . . . . . . . . . . . . . . 15 When to replace the AirClean exhaust filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Replacing the AirClean filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Exchanging exhaust filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

When to change the Active AirClean 30 or HEPA AirClean 30 exhaust filter . . . . . . 16 Replacing the Active AirClean 30 or HEPA AirClean 30 exhaust filter . . . . . . . . . 16 When to change the thread catcher on the standard floor brush . . . . . . . . . . . . . 16 Replacing the thread catchers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Cleaning and care
Frequently asked questions
After sales service
Optional accessories
Caring for the environment
LIMITED WARRANTY - VACUUM CLEANERS USA . . . . . . . . . . . . . . . . . . . .	19

en - IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE

Keep these operating instructions in a safe place and pass them on to any future user.

WARNING-

To reduce the risk of fire, electric shock or injury:

Before Using

Check the voltage rating of the vacuum cleaner before connecting the power cord to an electrical outlet. Your power source should correspond with the voltage rating plate located on the underside of the vacuum. Use only household AC outlets. Never use DC power sources. If you are not sure of your home’s voltage supply, consult a qualified electrician. Connecting the vacuum cleaner to a higher voltage may result in damage to the vacuum cleaner or injury.

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not alter the plug in any way.

A damaged vacuum cleaner can be dangerous. Check the packaging, vacuum cleaner and accessories for any signs of damage. Do not use a damaged appliance.

Do not use with a damaged cord or plug. If the appliance is not working as it should, has been dropped, damaged, left outdoors or submerged in water, bring it to a service center.

The electrical outlet must be fitted with a 15 A fuse.

en - IMPORTANT SAFETY INSTRUCTIONS

Use

Do not use on people or animals.

Do not use outdoors or on wet surfaces. Only dry surfaces should be vacuumed.

Use only as described in this manual. Use only Miele recommended accessories described in this manual.

This appliance is intended strictly for household use only.

Do not allow the vacuum cleaner to be used as a toy. Close attention is necessary when used near children.

Never use the vacuum cleaner without the FilterBag or filters in place. Otherwise, it could be damaged.

If the FilterBag is not inserted, the dust compartment lid will not close. Do not force it shut.

Do not leave the vacuum plugged in. Unplug it from the outlet when not in use and before servicing.

On the underside of the vacuum hand piece is a metal insert designed to absorb static electricity. Please make certain that your hand remains around this metal insert when vacuuming.

Persons who lack physical, sensory, or mental capabilities or experience with the machine should not use it without supervision or instruction by a responsible person.

Unwind the cord completely to aid the vacuum in dissipating heat.

This vacuum should not be used to entrap or retain any hazardous materials.

Do not use the vacuum cleaner to pick up liquids or damp dirt. This could impair the electrical safety of the vacuum cleaner. Wait for freshly shampooed carpets to dry.

Do not vacuum anything that is burning or smoking such as cigarettes, matches or hot ashes. The vacuum could catch fire.

Do not vacuum toner dust. Toner, such as that used in printers and photocopiers can conduct electricity.

Do not use the vacuum to pick up any flammable or combustible liquids such as gasoline or use in areas where they may be present.

Do not vacuum up items which are heavy, hard or have sharp edges. They could cause a blockage and damage the appliance.

Do not pull or carry by the cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do not run the appliance over the cord. Keep the cord away from heated surfaces.

Do not unplug by pulling the cord. To unplug grasp the plug, not the cord.

Do not handle the plug or vacuum with wet hands.

en - IMPORTANT SAFETY INSTRUCTIONS

Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

Do not place anything into the openings of the vacuum. Do not use if any openings are blocked; keep them free of dust, lint, hair or anything that may reduce air flow.

To avoid risk of injury while vacuuming, do not reach into the moving beater bar of the Powerbrush. Danger of injury.

This appliance is equipped with a power cord reel. Hold the plug when rewinding onto cord reel. Do not allow plug to whip when rewinding.

Turn off all controls before unplugging.

Use caution when vacuuming on stairs.

Floor attachments, accessories and wands must not be used at head level to avoid injuries to the eyes and ears.

Using accessories

The hose and telescopic wand contain electrical wires. Do not use the vacuum cleaner if these parts are damaged, cut or punctured. Avoid picking up sharp objects. There is the risk of electric shock.

The socket on the vacuum cleaner is only to be used with the Miele Powerbrush.

Unplug the vacuum when changing accessories, especially when using the Powerbrush.

The Miele Powerbrush is a

motor-driven accessory for use only with Miele vacuum cleaners. The vacuum must not be used with another manufacturer's Powerbrush.

Do not use the vacuum without an accessory attached. The rim could be damaged and injuries could result from sharp edges.

Miele FilterBags are disposable and intended to be used only once. Do not attempt to reuse them. An over stuffed bag will reduce the efficiency of the vacuum cleaner.

Only use genuine Miele FilterBags with the Miele quality signet and original Miele filters and accessories. Only then will the manufacturer guarantee its safety.

Always turn off this appliance before connecting or disconnecting motorized nozzle.

en - IMPORTANT SAFETY INSTRUCTIONS

Cleaning, maintenance and repairs

Turn the vacuum cleaner off after each use and before every cleaning / maintenance. Pull the plug from the outlet.

Never submerge the vacuum cleaner in water. Clean only with a dry cloth or slightly damp cloth when disconnected from the mains supply. If moisture gets into the appliance there is a risk of electrical shock.

Monitor the dust bag change indicator and inspect all filters regularly. For best performance, the FilterBag and filters should be replaced when necessary. A full bag or blocked filter will reduce the vacuum cleaners' suction power. A temperature limiter automatically switches the vacuum cleaner off if it gets too hot, see "Maintenance and Care - What if the vacuum turns off automatically?".

Repairs during the warranty period should only be performed by an authorized service agent in accordance with national and local safety regulations. Unauthorized repairs could cause injury or machine damage and may void the warranty.

Disposing of an old appliance

Before discarding an old vacuum cleaner, please cut off the power cord, and render the plug useless. Ensure the appliance presents no danger to children while being stored for disposal

SAVE THESE

INSTRUCTIONS

en - Guide to the vacuum cleaner

Hand piece

On/Off switch for the Powerbrush

Lock release button

Electro Telescopic wand SET 220

Elbow

Plug for Electro-accessories

Electro Telescopic wand release button

Dust compartment lid release

Suction power selector

Powerbrush SEB 217-3 / EB02 (not shown in these Operating Instructions) / SEB 228 / EB03

A separate Operating manual for the respective accessory is supplied with the vacuum.

Carrying handle

Socket for Electro-accessories

FilterBag

Dust compartment filter (pre-motor filter)

Exhaust filter

On/Off foot switch

Park-system

Power cord

Cord rewind switch

Airflow indicator

Accessory clip with three tools

Suction hose SES 116

Optional accessories are available from your Miele dealer or Miele.com

The illustrations referred to in the text are shown on the fold-out pages at the end of these operating instructions.

Before using the vacuum cleaner

Connecting the Electro hose (see fig. 1)

Insert the elbow into the suction socket until it clicks into place.

Insert the plug into the socket on the inside of the carrying handle.

Disconnecting the Electro hose

Remove the plug from the socket.

Press the two release buttons at the sides of the elbow and lift the hose from the socket.

Connecting the hand piece and the Electro Telescopic wand (see fig. 2)

Insert the hand piece into the electro telescopic wand until it clicks into place. Use the inlet guides to direct insertion.

To release the hand piece from the telescopic wand press the locking button (see arrow) and pull the hand piece away from the telescopic wand.

Using the Powerbrush

Observe the cleaning instructions of the floor manufacturer.

The Powerbrush is particularly suitable for cleaning and restoring crushed carpet pile of wall to wall carpeting and floor coverings subject to hard wear, especially in high traffic areas.

The Powerbrush can also be used on smooth floor surfaces.

Do not use the powerbrush on:

–(SEB 217-3 only) Floors with a variable or uneven surface. The brush could come into contact with the floor and cause damage.

–High quality, hand knotted rugs, for example Berber or Persian rugs, as well as extremely long piled area rugs and carpets. There is a danger of the threads being pulled out. Turn the Powerbrush off to vacuum these types of floor coverings and use only suction.

Connecting the Powerbrush to the Electro Telescopic wand (see fig. 3)

Insert the Electro Telescopic wand into the Powerbrush until it clicks into place.

To release the parts, press the lock release button and pull the wand up and out.

For more information on use and care please refer to the instructions supplied with the Powerbrush.

Using the standard floor brush

(depending on model)

Observe the cleaning instructions of the floor manufacturer.

The floor brush is suitable for cleaning carpets, rugs, carpeted stairs and hard surfaces that are not susceptible to scratching.

It is also suitable for vacuuming stairs (see fig. 4).

For your own safety, always vacuum stairs from bottom to top.

Connecting and adjusting the floor brush (see fig. 5)

(depending on model)

Place the floor brush into the suction hose and twist until it clicks into place.

To separate the parts, press the locking button.

To clean carpets and area rugs, press the foot switch , to clean hard flooring, press the foot switch .

Always use the floor brush with the bristles raised to clean floors with very deep joints or gaps.

Included accessories (see fig. 6 + 7)

Dust brush with natural bristles

Upholstery tool

Crevice nozzle

Accessory clip for the included accessories

Position the accessories as indicated.

Accessory clip

Press onto the elbow until it clicks into place.

Floor brush Hardfloor -3 (see fig. 8)

(depending on model)

To vacuum sturdy hard floors, e.g. tiles and stone floors.

Floor brush Parquet -3 (see fig. 8)

(depending on model)

Special brush with natural bristles intended for cleaning parquet and laminate floors, especially those susceptible to scratching.

Use

Power cord

Unwind the cord completely to aid the vacuum in dissipating heat.

Do not unplug by pulling the cord. To unplug grasp the plug, not the cord.

This appliance is equipped with a power cord reel. Hold the plug when rewinding onto cord reel. Do not allow plug to whip when rewinding.

Unwinding / Rewinding (see fig. 9)

Hold the plug and pull out the power cord.

To reduce the risk of electric shock, the vacuum has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, contact a qualified electrician. Do not alter the plug in any way.

Danger of overheating and damage.

Unplug the vacuum from the outlet.

Press the rewind switch - the power cord will rewind automatically. Hold the plug so that it does not whip around when rewinding.

Adjusting the Electro Telescopic suction wand (see fig. 10)

One part of the electro telescopic wand is fitted inside the other and can be adjusted to your height for comfortable vacuum cleaning.

Press the telescopic wand release button to release the tubes and adjust to the desired height.

Turning the vacuum On/Off (see fig. 11)

Press the On/Off foot switch .

Adjusting the suction (see fig. 12 + 13)

To prevent static electricity your hand must touch the metal inlay on the underside of the vacuum hand piece. Be certain to continuously touch this inlay when vacuuming fine dust, flour or sawdust as these materials are more likely to create a static discharge. To further prevent static discharge while vacuuming, pull the vacuum along by the hose with one hand while continuing to hold the hand piece in the other hand.

You can adjust the suction power to suit the type of flooring. By reducing the suction power the floor brush can be pushed easier.

The symbols on the controls indicate the type of use the settings are suitable for.

curtains, lightweight fabrics

upholstery, cushions

thick pile carpets, rugs and runners

energy saving, daily vacuuming with low noise level

low pile carpets

hard flooring and intensive cleaning of carpets

Turn the suction power selector to the desired setting.

Turning the Powerbrush On/Off (see fig. 14)

The Powerbrush is turned on and off separately from the vacuum using the hand piece.

The button allows you to turn off the Powerbrush, e.g. when moving from wall-to-wall carpeting to a persian rug.

Parking, transport and storage

Park system (see fig. 15)

(Cannot be used with the Powerbrush SEB 228 / EB03.)

The Park system allows you to conveniently park the telescopic wand on the vacuum cleaner during brief pauses.

Insert the lower clip on the floor brush into the slot on the end of the vacuum cleaner from above.

When vacuuming on a sloping surface, e.g. on a ramp, push all telescopic tubing parts completely together.

Transport and storage (see fig. 16)

For easier transportation and storage stand the vacuum cleaner vertically.

Insert the parking clip attachment on the floor tool or floor brush into the parking slot from above (does not apply to Powerbrush SEB 228 / EB03).

To save space, completely collapse the tubes in the telescopic wand.

Maintenance and care

Turn off and unplug the vacuum cleaner before performing any maintenance work.

The Miele filter system consists of the following three components.

–FilterBag

–Exhaust filter

–Dust compartment filter

Each of these components must be changed periodically to maintain the vacuum cleaner’s efficiency.

Only use Miele FilterBags, filters and accessories with the "Original Miele" logo. Only then can the suction power of the vacuum cleaner reach its optimum potential creating the best possible cleaning results.

The use of FilterBags made of paper or a similar material, or FilterBags with a cardboard retaining plate can lead to serious damage to the vacuum cleaner and possibly voiding the warranty, just as with the use of FilterBags without the "Original Miele" logo.

Purchasing new FilterBags and filters

Original Miele FilterBags and filters can be purchased from an authorized Miele vacuum dealer or by visiting the Miele store at http://store.miele.com.

Which FilterBags and filters are the right ones?

This vacuum cleaner uses Original Miele FilterBags Type G/N and an Original Miele filters, the "Original Miele" Logo will appear on the packaging or directly on the FilterBag.

An "AirClean" exhaust filter and a dust compartment filter are supplied with every box of Miele FilterBags.

If you would like to purchase additional Miele filters separately, contact your vacuum dealer or Miele, please quote the model number of your Miele vacuum cleaner to ensure correct parts are ordered. These parts are also available to order from the online Miele store.

The exhaust filter supplied with the vacuum cleaner can be exchanged with another type of Original Miele filter (see "Exchanging exhaust filters").

When to change the FilterBag (see fig. 17)

Change the FilterBag when the colored marker in the airflow indicator fills the display.

Miele FilterBags are disposable and made to be used only once. Do not attempt to reuse.

Checking the airflow indicator

Attach the standard floor brush (depending on model) to the vacuum cleaner. Perform this test with the floor brush only, other attachments can affect the function of the airflow indicator.

Turn the vacuum cleaner on and select the highest power setting.

Lift the floor brush slightly off the floor. If the marker completely fills the indicator window, the FilterBag needs to be changed.

How the airflow indicator works

The airflow indicator is designed to show when the bag is full of common household dust and measures the amount of air flow through the FilterBag. Normal household dust is a mixture of dust, hair, carpet fluff, threads, sand, etc.

However, if fine dust, such as drill dust, sand, plaster or flour is vacuumed, the pores of the FilterBag may become blocked. The marker will indicate that the bag is "full" even when it is not. The FilterBag should be changed as the suction power is greatly reduced.

If the bag is bulging with pet fur, hair, carpet fluff, etc. the indicator may not register "full". This is because the air flow of the FilterBag may still be high enough not to activate the marker to show maximum. The FilterBag should still be changed.

Replacing the FilterBag (see fig. 18 + 19)

Pull the plug from the socket

Open the dust compartment lid and raise until it clicks into place.

The FilterBag has a closing flap which closes automatically when the dust compartment lid is raised to prevent any dust from escaping.

Grasp the finger grip and pull the FilterBag out of the holder.

Insert the new FilterBag as far as it will go into the FilterBag holder. Do not unfold the FilterBag when taking it out of the box.

Unfold the FilterBag in the dust compartment.

Close the dust compartment lid until it clicks into place. Take care not to jam the FilterBag in the lid.

An empty-operation-barrier blocks the dust compartment lid from closing if no FilterBag is inserted. Do not force it closed.

When to change the dust compartment filter (Pre-motor filter)

Change the filter each time you open a new box of genuine Miele FilterBags. A dust compartment filter is supplied with each box.

Replacing the dust compartment filter (Pre-motor filter) (see fig. 20)

Open the dust compartment lid.

Open the filter frame, remove the old filter, and insert a new filter.

Close the filter frame.

Close the dust compartment lid.

When to replace the AirClean exhaust filter

Each time a new box of Miele FilterBags is opened, this filter should be changed. A new Air Clean exhaust filter is included in every box of Miele FilterBags.

Replacing the AirClean filter (see fig. 21)

Do not use more than one filter at a time.

Open the dust compartment lid.

Open the filter frame until it clicks, grasp the clean corner (see arrow) and remove the used filter.

Insert the new filter.

Close the filter frame.

Close the dust compartment lid.

Exchanging exhaust filters

Depending on the model, there may also be an Active AirClean 30 or a HEPA AirClean 30 exhaust filter included which can be used instead of the standard AirClean exhaust filter.

In order to use the Active AirClean 30 or the HEPA AirClean 30 filter the AirClean filter and filter frame must be removed. The exhaust filter change indicator must also be activated (see fig. 22).

After about 10-15 seconds, a small red marker will appear in the left-hand side of the display (see fig. 23).

+ 33 hidden pages