Micas AUTOLIGHT SMART DALI User Manual

AUTOLIGHT SMART DALI

Inhalt

Instruction: AUTOLIGHT SMART DALI ..................................................................................................... 3

Functional description ......................................................................................................................... 3

Mounting instruction........................................................................................................................... 4

Technical characteristics ..................................................................................................................... 5

AUTOLIGHT SMART DALI

Instruction: AUTOLIGHT SMART DALI

AUTOLIGHT SMART DALI is a small construction 5.8 GHz HF motion detector for switching, dimming and networking of individual luminaires up to complex light installations. Settings can easily be communicated via app via Bluetooth point to point or in the "mesh" network. It is possible to configure single luminaires, groups or profiles. The distance between the sensor units can be up to 20

m. The prerequisite for this is that the installation is located inside a building. The AUTOLIGHT

SMART DALI is equipped with a DALI interface which makes it possible to control up to 4 DALI "slaves" via broadcast operation. Since the sensor has no mechanical switching element, it is wearfree.

Functional description

The AUTOLIGHT SMART DALI detects motion in the detection field using a 5.8 GHz radar signal. It should be noted that radar signals can penetrate thin walls, doors and furniture. Thus, if necessary, movements are detected that take place in adjacent rooms. The entry field can be adjusted accordingly with the help of the app.

If the sensor has been taught in on a smart terminal via the app, various sensor settings can be made. These include:

- Sensitivity: Range adjustment of the sensor.

- Hold time: The time that the sensor stays on after being triggered.

- Lux: Below the set brightness threshold, triggering by movement is possible.

- Current brightness: Here the currently measured brightness can be taught as a threshold

value.

- Dim: Percentage brightness on which the luminaire is dimmed after the holding time has

elapsed (according to program mode).

- Dim On: Percentage brightness of the luminaire when it is switched on.

- Program mode:

o On / Off: Sensors switch on (Dim On Level) and off again after the set hold time. o Permanent: Sensors switch on (Dim-On-Level) and switch to the dimmed state (dim

level) after the set hold time has expired.

o Corridor: Sensors switch on (dim on level) and after the selected hold time into the

dimmed state (dim level). Then they turn off after the double hold time.

- Soft Dim: Gentle control of the brightness of the lamps with a transition time of 2 s.

In addition, settings for the networking of luminaires, the common switching in luminaire groups or the creation of sensor profiles for quick configuration are possible. These are described in more detail in the chapter Installation and Mesh Setup with the Micas App.

AUTOLIGHT SMART DALI

Mounting instruction

Two fastening straps allow the sensor to be screwed into the luminaire. During installation, it should be noted that the environment of the sensor can influence the detection properties and the detection field. The module must be installed flat on the base of the luminaire to allow for a detection field perpendicular to the baseplate. Any metal parts, in front of and to the side of the sensor, can change the detection field in size and shape. Shocks during operation should be avoided to prevent unwanted tripping. In order not to hinder the brightness measurement, the daylight sensor must not be covered directly. The HF motion detector is supplied with an operating voltage of 230 V ~ and 50 Hz via the L and N connections and has a standby power of less than 1 W. In addition, there are two DALI-compatible connection terminals as bus masters. Up to 4 DALI ballasts (DALI slaves) can be connected in parallel. To install the AUTOLIGHT SMART DALI, the total length of all DALI cables must not exceed 15 m. Additional bus power supplies must not be used and would damage the sensor.

The connection is made according to the following diagram:

LED Driver

AUTOLIGHT SMART DALI

Technical characteristics

Brief description

HF motion detector for installation in luminiares (built-in switch). Enables the connection of up to 4 DALI ballasts and radio networking with other sensors.

Operating Voltage

230 V~ ± 10 %, 50 Hz

Standby power

< 1 W

Terminal clamp

2 x two-pole string clamp

 L, N (230 V mains voltage)  DA+, DA- (DALI-compatible Master-interface)

Single wire conductor: 0,518...2,08 mm² (20...14 AWG) Stripping lenght: 7,5...8,5 mm

Interface / Switching power

 DALI compatible MASTER interface in broadcast mode:

0….4 loads with a total of max. 8 mA Total lenght of DALI cables max. 15 m

 Bluetooth interface (BLE 4.1) up to 20 m range inside buildings

Functional principle

HF motion detection

Frequency range

5,8 GHz ± 75 MHz

Emitted power

< 5 mW (<14 dBm EIRP)

Reach

 Up to 15 m (frontal, wall mounting)  Up to 10 m (Ø ceiling mounting)

Angle of coverage

Ca. 120° (depending on the light)

Speed detection

0,3 … 3 m/s (1 … 10 km/h)

Selectable functions

Via App on smart device

Sensitivity

10 … 100 %

Holding time

5 s … 60 min

Daylight sensor

1 Lux … 500 Lux, ∞, Teach

Dim level

0 … 100 %

Programm mode

On / Off, Permanent, Corridor Soft Dim: activ / inactiv

Factory settings

 Sensitivity: 70%  Holding time: 30 s  Lux: ∞  Dim: 30%  Programm mode: On / Off , Soft Dim: off

Installation hight

 Max. 2,7 m (wall mounting)  Max. 4 m (ceiling mounting)

Operating temperature

-20 … +60 °C

IP protection grade

IP 20 (in light mounting)

Glühdrahttemperatur

650°C

Isolation/Überspannung

 Protection class 0, built-in device  Pollution degree 2  Overvoltage category II  Impulse withstand voltage 2500 V  CTI 175 V

Dimensions

 84 x 30 x 21 mm

(L x B x H, incl. fixing clamps)

 70 x 30 x 21 mm

(L x B x H, without fixing clamps)

 80 mm drilling distance

Certification

CE (additional certifications available on request)

Micas AUTOLIGHT SMART DALI User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual