MGE UPS Systems EX 1500, EX 1000, EX 700 User Manual

0 (0)
MGE UPS Systems EX 1500, EX 1000, EX 700 User Manual

Installation and

user manual

Introduction

Thank you for selecting an MGE UPS SYSTEMS product to protect your electrical equipment.

The Pulsar EX range has been designed with the utmost care. We recommend that you take the time to read this manual to take full advantage of the many features of your UPS.

MGE UPS SYSTEMS pays great attention to the environmental impact of its products. Measures that have made Pulsar EX a reference in environmental protection include:

the eco-design approach used in product development;

recycling of Pulsar EX at the end of its service life.

To discover the entire range of MGE UPS SYSTEMS products and the options available for the Pulsar EX range, we invite you to visit our web site at www.mgeups.com or contact your MGE UPS SYSTEMS representative.

Page 2 - 51031604EN/AA

Safety

Safety rules

Safety of persons

A UPS has its own internal power source (the battery). Consequently, the power outlets may be energised even if the UPS is disconnected from the AC-power source.

Dangerous voltage levels are present within the UPS. It should be opened exclusively by qualified service personnel.

The UPS must be properly earthed. Measurements are required to ensure that the total leakage current of the UPS and the protected equipment does not exceed 3.5 mA.

The battery supplied with the UPS contains small amounts of toxic materials. To avoid accidents, the directives listed below must be observed:

Never burn the battery (risk of explosion).

Do not attempt to open the battery (the electrolyte is dangerous for the eyes and skin).

Comply with all applicable regulations for the disposal of the battery.

Batteries constitute a danger (electrical shock, burns). The short-circuit current may be very high. Precautions must be taken for all handling.

Product safety

UPSs must be connected to a nearby wall outlet that is easily accessible.

The UPS can be disconnected from the AC-power source by removing the power cord.

Never install the UPS near liquids or in an excessively damp environment.

Never let a foreign body penetrate inside the UPS.

Never block the ventilation grates of the UPS.

Never expose the UPS to direct sunlight or a source of heat.

Special precautions

The UPS connection instructions contained in this manual must be followed in the indicated order.

Check that the indications on the rating plate correspond to your AC-power system and to the actual electrical consumption of all the equipment to be connected to the UPS.

If the UPS must be stored prior to installation, storage must be in a dry place. The admissible storage temperature range is -20° C to +45° C.

If the UPS remains de-energised for a long period, we recommend that you energise the UPS for a period of 24 hours, at least once every month. This charges the battery, thus avoiding possible irreversible damage.

Prior to handling the battery:

remove all watches, rings, bracelets and any other metal objects;

use tools with insulated handles.

51031604EN/AA - Page 3

Foreword

Using this document

Information may be found primarily by consulting:

the contents,

the index.

Pictograms

Important instructions that must always be followed.

Information, advice, help.

Visual indication.

Action.

Audio indication.

In the illustrations on the following pages, the symbols below are used:

LED off.

LED on.

LED flashing.

Page 4 - 51031604EN/AA

Contents

1.Presentation

1.1

Pulsar EX range ..........................................................................................................................

7

 

Tower model ....................................................................................................................................

7

 

Rack model .....................................................................................................................................

7

1.2

Back .............................................................................................................................................

8

 

Tower model ....................................................................................................................................

8

 

Rack model .....................................................................................................................................

9

1.3

Control panel ...............................................................................................................................

10

2.Installation

2.1

Unpacking and checks ...............................................................................................................

11

 

Tower model ..................................................................................................................................

11

 

Rack model ...................................................................................................................................

12

2.2

Installation of the rack version ..................................................................................................

13

2.3

Connection to the RS 232 or USB communications port (optional) ........................................

14

2.4

Installation of the communications-card option ......................................................................

15

 

Tower model ..................................................................................................................................

15

 

Rack model ...................................................................................................................................

15

2.5

Connections ................................................................................................................................

16

 

Tower model ..................................................................................................................................

16

 

Rack model ...................................................................................................................................

16

3.Operation

3.1

Start-up ........................................................................................................................................

17

3.2

Bargraph indications ..................................................................................................................

17

3.3

Operation on battery power (following failure of AC input power) .............................................

18

 

Transfer to battery power ..............................................................................................................

18

 

Threshold for the low-battery warning ...........................................................................................

18

 

End of backup time .......................................................................................................................

18

 

Sleep mode ...................................................................................................................................

18

51031604EN/AA - Page 5

Contents

3.4

Personalisation (optional) ...........................................................................................................

19

 

Function ........................................................................................................................................

19

 

"ON / OFF conditions" tab .............................................................................................................

19

 

"Battery" tab ..................................................................................................................................

19

 

"Output" tab ...................................................................................................................................

20

 

"Bypass" tab ..................................................................................................................................

20

3.5

Shutdown .....................................................................................................................................

20

4.Maintenance

4.1

Troubleshooting ..........................................................................................................................

21

4.2

Replacement of the battery module ..........................................................................................

22

 

Tower model ..................................................................................................................................

22

 

Rack model ...................................................................................................................................

23

5. Environment .............................................................................................................

24

6.Appendices

6.1

Technical characteristics ...........................................................................................................

25

 

Simplified diagram ........................................................................................................................

25

 

Operating conditions .....................................................................................................................

25

6.2

Glossary.......................................................................................................................................

26

6.3

Index.............................................................................................................................................

27

Page 6 - 51031604EN/AA

1.1 Pulsar EX range

Tower model

Rack model

Rack

EX1000

1. Presentation

 

Dimensions in mm

 

(H x W x D)

EX 700 / EX 1000

235.5 x 145 x 400

EX 1500

235.5 x 145 x 505

 

 

 

 

 

Weight in kg

 

 

EX 700

10

EX 1000

12

 

 

EX 1500

15

 

Dimensions in mm

 

(H x W x D)

EX 700 Rack

88 (2U) x 482.6 x 430

EX 1000 Rack

88 (2U) x 482.6 x 430

EX 1500 Rack

88 (2U) x 482.6 x 493

 

 

 

Weight in kg

 

 

EX 700 Rack

14

EX 1000 Rack

16

 

 

EX 1500 Rack

20

51031604EN/AA - Page 7

1. Presentation

1.2 Back

Tower model

Pulsar EX 700 / Pulsar EX 1000

1

2

RS232 USB

3

4

5

6

1

7

2 8

9

10

11

Pulsar EX 1500

1

2

RS232 USB

3

4

 

5

1

8

 

 

9

2

10

 

6

 

7

 

11

1 slot for communications-card option.

2 RS232 communications port.

3USB communications port.

4four outlets for direct connection of protected equipment.

5connector for automatic detection of an additional battery module.

6input circuit breaker.

7socket for connection to AC-power source.

8connector for an additional battery module.

9pushbutton to test phase/neutral inversion of AC-power source.

10LED indicating phase/neutral inversion of AC-power source.

11two programmable outlets (outlet 1 and 2).

Page 8 - 51031604EN/AA

1. Presentation

Rack model

Pulsar EX 700 Rack / Pulsar EX 1000 Rack / Pulsar EX 1500 Rack

 

3

7

1

 

4

 

11

 

USB

 

 

 

 

1

2

 

RS232

 

 

 

 

 

 

 

2

6

 

10

9

5

8

1

slot for communications-card option.

7

socket for connection to AC-power source.

2

RS232 communications port.

 

8

connector for an additional battery module.

3

USB communications port.

 

9

pushbutton to test phase/neutral inversion of

 

 

 

 

AC-power source.

 

4four outlets for direct connection of

protected equipment.

10 LED indicating phase/neutral inversion of

 

AC-power source.

5connector for automatic detection of an

additional battery module.

11 two programmable outlets (outlet 1 and 2).

6input circuit breaker.

51031604EN/AA - Page 9

Loading...
+ 19 hidden pages