Size:
647.88 Kb
Download

INSTALLATION INSTRUCTIONS FOR PART 99-7424

APPLICATIONS

Nissan Titan 2008-11

99-7424

KIT FEATURES

DIN Radio Provision with Pocket

ISO Mount Radio Provision with Pocket

Painted To Match Factory Dash

KIT COMPONENTS

A) Single DIN Radio Housing • B) ISO Trim Plate • C) ISO Brackets • D) Trim Panel

• E) Two Sided Tape (Not Shown)

BC A

D

Harness & Antenna Connections (sold separately)

70-7550- Nissan Harness95-up

TOOLS REQUIRED:

Torx T-10Driver • Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver

1-800-221-0932www.metraonline.com

© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION

99-7424

TABLE OF CONTENTS

Dash Disassembly

Nissan Titan 2008-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . 2

Kit Assembly

- DIN Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 4

Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

*Note:

Refer also to the instructions included with the aftermarket radio.

99-7424DASH DISASSEMBLY

NISSAN Titan 2008-11

A

1Disconnect the negative battery terminal to prevent an accidental short circuit.

2Unclip the entire dash panel including the radio and climate controls. Unplug and remove the panel. (Figure A)

3Remove (4) Phillips screws securing the radio chassis. Unplug and remove the chassis. (Figure B)

B

4Remove (4) T-10Torx screws securing the climate controls to the dash panel and remove the controls from the panel. (Retain the screws and climate controls forre-useduring kit preparation.)(Figure C)

5Remove (2) T-10Torx screws securing the passenger air bag status light assembly to the dash panel and remove the light from the panel.

(Retain the screws and light for re-

C

use during kit preparation.) (Figure C)

 

NOTE: The small round Airbag sticker also needs to be removed from the factory panel and placed onto the99-7424radio housing panel. (A round piece ofdouble-sidedtape is provided in case the factory sticker is not strong enough.)(Figure C)

Continue to kit preparation

1

99-7424KIT PREPARATON

NISSAN Titan 2008-11

A

1 Attach the climate controls to the Trim Panel using the factory hardware removed during the dash disassembly.(Figure A)

2 Attach the passenger air bag status light assembly to the Trim Panel using the factory hardware removed during the dash disassembly. Also, apply to air bag button the small round airbag sticker previously removed in Step 5 dash disassembly.(Figure B)

Continue to kit assembly.

B

2

99-7424KIT ASSEMBLY

DIN RADIO PROVISION WITH POCKET

*Note: Refer also to the instructions included with the aftermarket radio.

A

1Slide the DIN cage into the Single DIN Radio Housing and secure by bending the metal locking tabs outward.

2Slide the aftermarket radio into the cage until it snaps into place.

(Figure B)

Continue to final assembly.

B

3

99-7424KIT ASSEMBLY

ISO MOUNT RADIO PROVISION WITH POCKET

*Note: Refer also to the instructions included with the aftermarket radio.

A

1Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A)

2Slide the radio into the radio housing until it snaps into place. (Figure B)

3Snap the Trim plate onto the front of the Radio Housing. (Figure B)

Continue to final assembly.

B

4

99-7424FINAL ASSEMBLY

FINAL ASSEMBLY

A

(A) Strip wire ends back 1/2"

B

B) Twist ends together

 

 

C) Solder

C

D) Tape

 

D

 

1Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)

2Re-connectthe negative battery terminal and test the unit for proper operation.

3Reassemble in reverse order of disassembly using the 99-7424Trim Panel in place of the factory radio trim panel.

FINAL WIRING CONNECTIONS

Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and

individually tape off ends of any unused wires to prevent electrical short circuit.

METRA / EIA WIRING CODE

 

 

12V

Ignition / Acc. . . . . . . . . .

Red

Right Front (+) . . . . . . . . . . . .

Gray

12V

Batt / Memory. . . . . . . . .

Yellow

Right Front (-). . . . . . . . . . . . .

Gray/ Black

Ground. . . . . . . . . . . . . . . . . .

Black*

Left Front (+) . . . . . . . . . . . . .

White

Power Antenna. . . . . . . . . . . .

Blue

Left Front (-). . . . . . . . . . . . . .

White / Black

Amp Turn-On . . . . . . . . . . . . .

Blue / White

Right Rear (+) . . . . . . . . . . . .

Violet

Amp Ground. . . . . . . . . . . . . .

Black / White

Right Rear (-) . . . . . . . . . . . . .

Violet / Black

Illumination . . . . . . . . . . . . . .

Orange

Left Rear (+) . . . . . . . . . . . . .

Green

Dimmer . . . . . . . . . . . . . . . . .

Orange / White

Left Rear (-) . . . . . . . . . . . . . .

Green / Black

*NOTE: When a Black wire is not present, ground radio to vehicle chassis.

All colors may not be present on all leads due to manufacturer’s specifications.

5

99-7424INSTRUCTIONS

1-800-221-0932www.metraonline.com

REV. 11/18/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-7424