Mazda TRUCK B SERIES 2004 Owner Manual

Table of Contents

Introduction 4 Instrument Cluster 12

Warning and control lights 12 Gauges 16

Entertainment Systems 18

AM/FM stereo 18 AM/FM stereo with single CD 19 AM/FM stereo tape/CD/MP3 22 Premium AM/FM stereo CD6/MP3 26

Climate Controls 31

Heater only 31 Manual heating and air conditioning 32

Lights 34

Table of Contents

Headlamps 34 Turn signal control 36 Bulb replacement 36

Driver Controls 43

Windshield wiper/washer control 43 Steering wheel adjustment 44 Power windows 45 Speed control 49

Locks and Security 55

Keys 55 Locks 55 Anti-theft system 55

Table of Contents

Seating and Safety Restraints 63

Seating 63 Safety restraints 65 Air bags 77 Child restraints 89

Driving 105

Starting 105 Brakes 110 Transmission operation 114 Vehicle loading 124 Trailer towing 128 Recreational towing 135

Roadside Emergencies 137

Hazard flasher switch 137 Fuel pump shut-off switch 137 Fuses and relays 138 Overheating 148 Changing tires 149 Jump starting 157 Wrecker towing 162

Customer Assistance 163

Reporting safety defects (U.S. only) 173

Cleaning 174

Table of Contents

Maintenance and Specifications 180

Engine compartment 190 Engine oil 194 Battery 200 Fuel information 208 Refill capacities 240 Lubricant specifications 243 Engine data 244

Accessories 248 Index 249

All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from MNAO. MNAO may change the contents without notice and without incurring obligation.

Introduction

CALIFORNIA Proposition 65 Warning

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

CONGRATULATIONS

Congratulations on acquiring your new Mazda product. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it.

For more information on Mazda and its products visit the following website:

• In the United States: www.mazdausa.com

• In Canada: www.mazda.ca

Additional owner information is given in separate publications. This Owner’s Guide describes every option and model variant available

and therefore some of the items covered may not apply to your particular vehicle. Furthermore, due to printing cycles it may describe options before they are generally available.

Remember to pass on the Owner’s Guide when reselling the vehicle. It is an integral part of the vehicle.

WARNING: In the event of an accident the Fuel pump shut-off switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g. collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside emergencies chapter.

Introduction

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide

How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by a bold WARNING statement. These comments should be read and observed.

Warning symbols on your vehicle

When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.

Protecting the environment

We must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol.

Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.

BREAKING-IN YOUR VEHICLE

There are no particular breaking-in rules for your vehicle. During the first 1,600 km (1,000 miles) of driving, vary speeds frequently. This is necessary to give the moving parts a chance to break in.

Introduction

SPECIAL NOTICES Emission warranty

The New Vehicle Limited Warranty includes Bumper to Bumper Coverage, Safety Restraint Coverage and Corrosion Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.

Event Data Recorder

The computer in your vehicle is capable of recording detailed data potentially including but not limited to information such as:

• the use of restraint systems including seat belts by the driver and passengers,

• information about the performance of various systems and modules in the vehicle, and

• information related to engine, throttle, steering, brake or other system status potentially including information related to how the driver operates the vehicle including but not limited to vehicle speed.

This information may be stored during regular operation or in a crash or near crash event. This stored information may be read out and used by:

• service and repair facilities.

• law enforcement or government agencies.

• the Manufacturer and Distributor.

Special instructions

For your added safety, your vehicle is fitted with sophisticated electronic controls.

WARNING: Please read the section Supplemental Restraint System (SRS) in the Seating and Safety Restraints chapter.

Failure to follow the specific warnings and instructions could result in personal injury.

WARNING: Front seat mounted rear facing child or infant seats should NEVER be used in front of a passenger side air bag unless the air bag can be and is turned OFF.

Introduction

Notice to owners of pickup trucks and utility type vehicles

WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles.

Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of vehicle control, vehicle rollover, personal injury or death.

Be sure to read Driving off road in the Driving chapter.

Using your vehicle with a snowplow

WARNING: Do not use this vehicle for snowplowing.

Your vehicle is not equipped with a snowplowing package.

Using your vehicle as an ambulance

WARNING: Do not use this vehicle as an ambulance.

Your vehicle is not equipped with the an ambulance preparation package.

Introduction

These are some of the symbols you may see on your vehicle.

Vehicle Symbol Glossary

Safety Alert

Protecting the Environment

Air Bag-Front Air Bag-Side

Child Seat

Child Seat Lower Anchor

Brake System Anti-Lock Brake System

Brake Fluid Non-Petroleum Based

Hazard Warning Flasher Fog Lamps-Front

Fuse Compartment Fuel Pump Reset

See Owner’s Guide

Fasten Safety Belt

Child Seat Installation Warning

Child Seat Tether Anchor

Master Lighting Switch

Windshield Wash/Wipe

Rear Window Defrost/Demist

Windshield Defrost/Demist

Power Windows

Vehicle Symbol Glossary

Power Window Lockout

Engine Oil Engine Coolant

Engine Coolant Temperature

Personal Alarm System Feature

Do Not Open When Hot

Instrument Cluster

4wd control*

(pg. 120)

Audio system

(pg. 18)

Auxiliary power point

(pg. 45)

Cigar lighter

Passenger air bag deactivate switch

(pg. 84)

Fog lamp control

Climate control system

(pg. 31)

(pg. 34)

* if equipped

Instrument Cluster

WARNING LIGHTS AND CHIMES

Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, have the respective system inspected immediately.

Check engine: The Check Engine indicator light illuminates when the ignition is first turned to the ON position to check the bulb. Solid illumination after the engine is started indicates the On Board Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (OBD-II) in the Maintenance and Specifications chapter. If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately.

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.

Instrument Cluster

Check fuel cap: Illuminates when the fuel cap may not be properly installed. Check the fuel filler cap if this light remains on. Continued driving with this light on may cause the Check Engine warning light to come on.

It may take a long period of time for the system to detect an improperly installed or properly re-installed fuel filler cap depending on driving and fuel tank level conditions. Refer to Fuel

filler cap in the Maintenance and Specifications chapter.

Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON position when the engine is not running, or in a position between ON and START, or by applying the parking brake when the ignition is turned to the ON position. If the brake system warning light does not illuminate at this time, seek service immediately from your dealership. Illumination after releasing the parking brake indicates low brake fluid level or a failure to brake proportioning and the brake system should be inspected immediately by your servicing dealership.

WARNING: Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have the vehicle checked by your dealer immediately.

BRAKE

Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected; have the system serviced immediately. Normal braking is still functional unless the brake warning light also is illuminated.

ABS

Instrument Cluster

Air bag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately. A chime will also sound when a malfunction in the supplemental restraint system has been detected.

Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt. Refer to the Seating and safety restraints chapter.

Charging system: Illuminates when the battery is not charging properly.

Engine oil pressure: Illuminates when the oil pressure falls below the normal range, refer to Engine oil in the Maintenance and specifications chapter.

Engine coolant temperature:

Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as possible , switch off the engine and let cool. Refer to Engine coolant in the Maintenance and specifications chapter.

WARNING: Never remove the coolant recovery cap while the engine is running or hot.

Low fuel: Illuminates when the fuel

level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter).

Door ajar: Illuminates when the ignition is in the ON position and any door is open.

Instrument Cluster

Overdrive off (if equipped):

Illuminates when the overdrive function of the transmission has been turned off, refer to the

Driving chapter. If the light does not come on or the light flashes steadily, have your vehicle serviced as soon as possible, damage to the transmission could occur.

Four wheel drive low (if equipped): Illuminates when

four-wheel drive low is engaged. NOTE: If the light continues to

flash have the system serviced.

Four wheel drive high (if equipped): Illuminates when

four-wheel drive high is engaged. It may also illuminate when the 4WD LOW is engaged, refer to the Driving chapter for more information.

NOTE: If the light continues to flash have the system serviced. Anti-theft system: Flashes when

the Securilocky Passive Anti-theft System has been activated.

Speed control: Illuminates when the speed control is engaged. Turns off when the speed control system is disengaged.

O/D

OFF

4x4

LOW

4x4

Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster, check for a burned out bulb.

High beams: Illuminates when the high beam headlamps are turned on.

Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and the driver’s door is opened.

Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver’s door is opened.

Door ajar warning chime: Sounds when any door is opened (or not fully closed).

GAUGES

Speedometer: Indicates the current vehicle speed.

Engine coolant temperature gauge: Indicates engine coolant

temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section,

the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.

Refer to Engine coolant in the Maintenance and specifications chapter.

WARNING: Never remove the coolant reservoir cap and/or the radiator cap while the engine is running or hot, this may result in serious burns.

Odometer: Registers the total

kilometers (miles) of the vehicle.

Trip odometer: Registers the kilometers (miles) of individual journeys. To reset, depress the control button.

Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.

Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade.

NOTE: The FUEL icon and arrow indicates which side of the vehicle the fuel filler door is located.

Refer to Filling the tank in the Maintenance and Specifications chapter for more information.

AM/FM STEREO (IF EQUIPPED)

1. AM/FM: Press to select AM/FM1/FM2 frequency bands.

2. CLK: Press until SELECT HOUR / SELECT MINUTE appears.

Press the hours/minutes.

Press CLK to display the time when the ignition is off.

3. AUDIO: Press AUDIO to toggle through the following modes

and use adjustments in those modes.

Bass: Press

AUDIO to adjust

/ to make

AUDIO to decrease/increase the bass setting.

Treble: Press

4. Tune: Press to manually go down/up ( / ) the radio frequency and in audio mode to select various settings.

5. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. To tune a preset station, press the desired memory preset.

6. SEEK: Press access the previous or next

radio station. If pressed for less than .5 seconds, the system will seek to the next or previous station.

7. ON/OFF/Volume: Press to turn the system ON/OFF. Turn to adjust the volume levels. If the volume is set above a certain level, and the ignition is turned off, the volume will come back to a “nominal” listening level when the ignition is turned back on.

AM/FM STEREO CD

SEEK to

Entertainment Systems

1. CD eject: Press to eject the CD.

2. CLK (Clock):Press CLK until SELECT HOUR or SELECT MINUTE is displayed. Press

TUNE to adjust the

hours/minutes. Press CLK to display the time when the ignition is off.

3. MUTE:Press to mute the playing media. Press again to return to the playing media.

4. MENU: Press MENU repeatedly to toggle through the following

modes and use adjustment in those modes.

Autoset: Press set the strongest local radio stations

for AM/FM1/FM2 without losing your original manually set preset stations. When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets.

Bass: Press

/ to make

MENU to

MENU to decrease/increase the bass setting.

Treble: Press

Balance: Press

right speakers. Fade: Press

rear speakers.

5. TUNE: Press to manually go down/up ( frequency and also to select

various settings in menu mode.

MENU to decrease/increase the treble setting.

MENU to adjust the audio between the left and

MENU to adjust the audio between the front and

/ ) the radio

Entertainment Systems

6. SHUFF (Shuffle): Press to play the tracks on the current CD in random order.

7. REPEAT:Press to repeat the current CD track.

8. FF (Fast forward): Press to manually advance in a CD track.

9. REW (Rewind): Press to manually reverse in a CD track.

10. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. To recall a previously set station, press the desired memory preset button briefly.

11. SEEK/TRACK: Press to access the next/previous strong station. In CD mode, press to advance to the next/previous track.

12. SCAN: Press to toggle between SCAN ON and SCAN OFF. When activated, the system scans up through and plays a brief sampling of available radio stations or CD tracks. Press again to stop.

13. AM/FM:Press to select AM/FM1/FM2 frequency band.

14. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.

15. CD: Press to enter CD mode. If a CD is already present in the system, the disc will begin to play.

16. CD slot: Insert a CD label side up.

CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Mazda CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your dealer for further information.

AM/FM STEREO TAPE/CD/MP3

1. CD eject: Press to eject the CD.

Entertainment Systems

2. CLK (Clock): Press CLK until SELECT HOUR or SELECT MINUTE is displayed. Press

MENU to adjust the hours/minutes. Press CLK to display the time of day when the ignition is off.

3. MUTE: Press to mute the playing media. Press again to return to the playing media.

4. MENU: Press MENU repeatedly to toggle through the following

modes and use adjustment in those modes.

Autoset:

autoset setting. Allows you to set the strongest local radio stations without losing your original manually set

preset stations for AM/FM1/FM2 . Use When the six strongest stations are filled, the station stored in preset 1 will

begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. Press again to disengage.

Bass: Press MENU to decrease/increase the level of bass.

Press MENU to access the

/ to make

MENU to set.

Treble: Press Balance: Press

right speakers. Fade: Press

rear speakers. Next/previous directory: In MP3 mode, press

the previous or next MP3 directory. Flat file/directory mode: Press

or Directory mode. Track number/music name/file name: In MP3 mode, press

MENU to view by track number, music name or file name.

Dolby:

Press

Dolbyt noise reduction: Reduces tape noise and hiss.

MENU to cycle Dolby ON/OFF. The Dolbyt noise

MENU to decrease/increase the level of treble.

MENU to adjust the audio between the left and

MENU to adjust the audio between the front and

MENU to go to

MENU to select Flat file mode

Entertainment Systems

reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Dolbyt and the double-D symbol are registered trademarks of Dolbyt Laboratories Licensing Corporation.

5. TUNE: Press to manually go down/up ( frequency and also to select

various settings in menu mode.

6. Tape eject: Press to eject the tape.

7. Tape 1–2: Press to change playing sides of the tape.

8. TEXT: In MP3 mode, press to view the next 12 characters in the MP3 Music name/file name of the current MP3 track and directory.

9. SHUFF (Shuffle): In CD or MP3 mode, press to play the tracks on the current CD/MP3 in random order. In MP3 directory mode, press to play the tracks within the current directory in random order.

10. REPEAT: Press to repeat the current CD/MP3 track.

/ ) the radio

11. FF (Fast forward): In tape mode, press to fast forward the tape. In CD mode, press to manually advance in a CD track.

12. REW (Rewind): In tape mode, press to rewind the tape. In CD mode, press to manually reverse in a CD track.

13. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. To select a preset station, press the desired memory preset button.

14. AM/FM: Press to select AM/FM1/FM2 frequency band.

Entertainment Systems

15. SEEK/TRACK: In radio mode, press next/previous strong station. In CD and MP3 flat file mode, press to

access the next track. In MP3 directory mode, press to select the next/previous track in the current directory.

16. Scan: In radio mode, scan through the available stations. In tape mode, you may set SCAN on or off. If activated, the player will scan the tape and plays a short Introduction of each song. In CD and MP3 flat file mode, you may set the scan on or off. If activated, the system will scan through each track. In MP3 directory mode, you may set scan on or off. If activated, the system will scan in the current directory.

17. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.

18. CD: Press to enter CD mode. If a CD is already in the system, the disc will begin play.

19. CD slot: Insert a CD, label side up.

/ to access the

PREMIUM AM/FM STEREO CD6/MP3

1. AM/FM: Press to select AM/FM1/FM2 frequency bands.

2. CD: Press to enter CD mode. If a CD is already in the system, the disc will start playing.

3. EJ (CD eject): Press to eject the CD. Press and hold to eject all CDs.

4. CLK (Clock): Press CLK until SELECT HOUR or SELECT MINUTE is displayed. Press

MENU to adjust the hours/minutes. Press CLK to display the time when the ignition is off.

5. MUTE: Press to mute the playing media. Press again to return to the playing media.

Entertainment Systems

6. MENU: Press MENU repeatedly to toggle through the following

modes and use adjustment in those modes.

Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for

AM/FM1/FM2 . Press MENU to access. Use When the six strongest stations are filled, the station stored in preset 1

will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets.

/ to make

MENU to set.

Bass: Press

Treble: Press

Balance: Press

right speakers. Fade: Press

rear speakers. Next/previous directory: In MP3 mode, press MENU

the previous/next directory. Flat file/directory mode: In MP3 mode, press MENU to access this

feature. Use Track #/normal music name/file name: Press MENU to access and

use name or file name).

/ to scroll through MP3 display options (track #, normal music

7. TUNE/DISC: Press to manually go down/up ( frequency, select the previous/next CD or to select various settings in menu mode. In MP3 directory mode, press previous/next directory

8. TEXT: In MP3 normal music name/file name mode, press to view the next 12 characters in the MP3 music name/filename of the current MP3 track and directory.

MENU to decrease/increase the bass setting.

MENU to decrease/increase the treble setting.

MENU to adjust the audio between the left and

MENU to adjust the audio between the front and

/ to go to

MENU to select flat file mode or directory mode.

/ ) the radio

/ to access the

9. SHUFF (Shuffle): Press to play the tracks on the current CD/MP3 in random order. In MP3 directory mode, press to play the tracks within the current directory in random order.

10. REPEAT: Press to repeat the current CD/MP3 track.

11. FF (Fast forward): Press to manually advance in a CD track.

12. REW (Rewind): Press to manually reverse in a CD track.

13. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. To select a preset station, press the desired memory preset.

14. SEEK/TRACK: In radio, CD and MP3 flat file mode, press to access the next/previous strong station or track. In MP3 directory

mode, press to select the next/previous track in the current directory.

15. SCAN: In radio, CD and MP3 flat file mode, press for a brief sampling of radio stations or CD/MP3 tracks. In MP3 directory mode, press to hear a brief sampling of all tracks in the current directory. Press again to stop.

16. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decrease volume. If the volume is set above a certain level and the ignition is

Entertainment Systems

RADIO FREQUENCIES

AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are:

AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz

RADIO RECEPTION FACTORS

There are three factors that can affect radio reception:

• Distance/strength: The further you travel from an FM station, the

weaker the signal and the weaker the reception.

• Terrain: Hills, mountains, tall buildings, power lines, electric fences,

traffic lights and thunderstorms can interfere with your reception.

• Station overload: When you pass a broadcast tower, a stronger signal

may overtake a weaker one and play while the weak station frequency is displayed.

CASSETTE/PLAYER CARE

Do:

• Use only cassettes that are 90 minutes long or less.

• Tighten very loose tapes by inserting a finger or pencil into the hole

and turning the hub.

• Remove loose labels before inserting tapes.

• Allow tapes which have been subjected to extreme heat, humidity or

cold to reach a moderate temperature before playing.

• Clean the cassette player head with a cassette cleaning cartridge after

10–12 hours of play to maintain good sound/operation.

Entertainment Systems

Don’t:

• Expose tapes to direct sunlight, extreme humidity, heat or cold.

• Leave tapes in the cassette player for a long time when not being

played.

CD/CD PLAYER CARE

Do:

• Handle discs by their edges only. Never touch the playing surface.

• Inspect discs before playing. Clean only with an approved CD cleaner

and wipe from the center out.

Don’t:

• Expose discs to direct sunlight or heat sources for extended periods

of time.

• Insert more than one disc into each slot of the CD changer magazine.

• Clean using a circular motion.

CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Mazda CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ball point pens may damage CDs. Please contact your dealer for further information.

AUDIO SYSTEM WARRANTY AND SERVICE

Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your authorized Mazda dealership.

+ 226 hidden pages