Mazda 0000-8F-H28, KD53-V7-629 Instructions Manual
GENUINE Mazda Mobile Start
INSTALLATION INSTRUCTIONS
Thank you for purchasing a genuine Mazda accessory.
Before removal and installation, be sure to thoroughly read these instructions. Please read the contents of this
booklet in order to properly install and use the Mazda Mobile Start. Your safety depends on it.
Keep these instructions with your vehicle records for future reference.
WARNING
There are several WARNING and CAUTION sections in this booklet concerning safety when installing or
•
removing the Mazda Mobile Start. Always read and follow them in order to prevent injuries, accidents, and possible
damage to the vehicle.
WARNING: Indicates a situation in which serious injury or death could result if the warning is ignored.
CAUTION: Indicates a situation in which bodily injury or damage to the vehicle could result if the caution is ignored.
• For areas indicating the tightening torque in this instruction manual, tighten to the specified torque using a torque wrench. For
areas in which the tightening torque is indicated inside parentheses ( ), the tightening torque is indicated as a reference value,
however tightening using a torque wrench is not necessary.
• Do not modify the Mazda Mobile Start.
• Do not install the Mazda Mobile Start in any way other than described in the following instructions.
• If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in installation.
• If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice before using it.
• Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons and property that arise from the
failure of the dealer or installer to follow these instructions.
• To ensure safety and reliability of the work, installation, removal and disposal work must be carried out by an Authorized
Mazda Dealership.
• Be careful not to lose removed parts, and be sure that they are kept free from scratches, grease or other dirt.
PART NUMBER :
NOTE
To the dealer
Please turn over these instructions to the customer after installation.
•
To the customer
Keep these instructions after installation. The instructions may be necessary for
•
installing other optional parts or removal of this accessory.
Should the vehicle or this accessory be resold, always leave these instructions
•
with it for the next owner.
PART NAME :
VEHICLE :
Mazda Mobile Start (MMS)
Mazda 6
0000-8F-Z80 (MMS ECU Kit)
0000-8F-H28 (MMS Harness Kit)
[KD53-V7-629 (Hood Switch)]
1
090003-33260700
1. INSTALLATION VIEW
(Sold separately) Hood switch
(Only for vehicles without theft-deterrent or without i-ELOOP system)
GPS & TEL Antenna Cables
MMS 2P Connector
RES Diagnostic Connectors
GPS Antenna
MMS ECU
TEL Antenna
Harness (GND)
MMS Harness
LED Connector
2
2. PARTS
Note
• Verify that the kit includes all the following parts and that they are free of dirt, scratches, or damage.
MMS ECU KIT (Part no. 0000-8F-Z80)
Part Part Name Qty. Part Part Name Qty. Part Part Name Qty.
MMS ECU
Double-sided
adhesive tape
(25 x 69mm)
Owner's Manual
1
1
1
Wire Tie
(White 200mm)
MMS Key Tag
: Part marked with a star mark is not used for this vehicle.
«
5
1
Urethane
Foam tape
(35 x 115mm)
«
Double-sided
adhesive tape
(25 x 25mm)
HARNESS KIT (Part no. 0000-8F-H28)
Part Part Name Qty. Part Part Name Qty. Part Part Name Qty.
MMS Harness
FH Protection
Sheet
TEL Film
Antenna
1
1
1
LED
GPS Film
Antenna
TEL Antenna
Cable
1
1
1
«
Harness Clamp
GPS Antenna
Cable
Antenna
Template
2
3
2
1
1
«
Electro tap
Installation
Instructions
(ENG/SPA/FRE)
: Parts marked with a star mark are only used on vehicles without theft-deterrent or without i-ELOOP system.
«
1
3
Wire Tie
(White 200mm)
A-Pillar Clip
(D651-68-162A)
15
1
Urethane
Foam tape
(35 x 115mm)
«
Wire Tie
(Black 200mm)
(Sold separately) The following parts are also necessary for installation.
Note
• These parts are not necessary for vehicles with theft-deterrent or with i-ELOOP system because the hood
switch is already equipped.
HOOD SWITCH KIT (Part no. KD53-V7-629)
Part Part Name Qty. Part Part Name Qty.
Hood switch
1
Screw
1
2
10
3
3. BEFORE INSTALLATION
WORKSHOP
MANUAL
REQUIRED TOOLS
• 10mm Socket Wrench • Scissors • Torque Wrench • Taped Flathead Screwdriver • Mat
• Electrical Tape • Panel Removal Tool • Soft clean cloth • Squeegee • Glass Cleaner • Nipper
• Pliers • Primer (3M Promoter-4298) • IPA (Isopropyl alcohol) • Phillips Screwdriver
WARNING
When the negative battery cable
is connected during operation, it
may cause electric shock or other
personal injuries. Disconnect the
negative battery cable before
removal/installation.
When connecting or disconnecting
connectors, grasp the connectors,
not the wires. Otherwise a short,
an accident from poor contact or
re may occur.
Do not pull the harness with
excessive force. Doing so can
cause a breakage or a shortrelated accident, as well as an
electrical short or re.
Park the vehicle on a level ground.
Set the vehicle on park (P) and
apply the parking brake. Be sure to
turn the ignition switch off, otherwise
the vehicle can move, causing
personal injury or vehicle damage.
CAUTION
Using improper tools may cause
damage and or broken parts.
Use the correct tool for the job.
Wrap protective tape around
screwdrivers and fastener
removal tools to prevent
scratching the vehicle.
Put the removed parts and the
parts in the kit on the protective
sheet to prevent scratches.
Excessive length of wire tie may
interfere with other parts and
cause damage. Cut unnecessary
part up to about 5 mm {0.19 in}
from the xed point.
• When the negative battery cable is removed, the clock, radio, trip meters and other memories will be erased.
Make sure to record the content of the memory.
• Refer to the Workshop Manual for removal and installation of vehicle parts. Not following the procedures for
removal/installation in the Workshop Manual could result in an accident or vehicle malfunction.
4. CONNECTION USING ELECTRO-TAP
Vehicle wiring harness
1
Electro tap
2
Vehicle wiring harness
Harness
3
Vehicle wiring harness
5
Lock
4
Firmly press using pliers
Terminal
Branch connection procedure using electro tap.
1. Insert the vehicle wiring harness into the electro tap.
2. Fold the electro tap as shown in the gure and lock it.
Caution
• Firmly engage the lock part until a click sound is heard.
3. Insert the harness to the end of the electro tap.
4. Firmly press the electro tap terminal using pliers.
5. Fold the electro tap in the direction of the arrow shown in
the gure and lock it.
4
5. CONNECTION DIAGRAM
GPS
20XX-
CONNECTORS
MAZDA MOBILE START (MMS)MMSMAZDA
ROOM
Battery
Pre connector
Pin : 1
B1
RES LED
F2
RES Connector
ANTENNA
SSU
(Start
/
+B
A10
F1
LED
A5
MMS ECU
E1
D1
RDIG
A16
GPS
GPS
TEL
TEL
STX
A4
TEL
ANTENNA
Pre connector
Stop
control Unit)
Pin:2
B2
VEHICLE
CONNECTOR
10
GND (M6)
C1
**
Connector to Connector
**
MMS Wire
Vehicle Wire
Scotch lock connection
MMS or Vehicle Terminal Insert
A
5
34
16 19
(FEMALE PIN)
B
21
(
FEMALE PIN
SRX
GND
A19
A3
C
(TERMINAL PIN)
)
D
1
(MALE PIN)
E
1
(FEMALE PIN)
VEHICLE OPTION CONNECTOR
112
(
)
MALE PIN
F
(MALE PIN)
TEL
1
(
FEMALE PIN
)
GPS
1
(
FEMALE PIN
)
5
6. VEHICLE DISASSEMBLY
Note
• Be careful not to damage or lose any parts removed from the vehicle since they will be reused.
1. Place the vehicle in park with the parking brake engaged.
2. Disconnect negative battery terminal and wrap tape
around it to insulate.
Warning
• When the negative battery cable is connected during
operation, it may cause electric shock or personal injuries.
Disconnect the negative battery cable before removal/
installation.
Bolt tightening torque: 4.0 - 6.0 N•m (2.9 - 4.4 ft•lbf)
Front Scuff Plate
Tab A
Hook A
(1)
(2)
Tab B
Cap Nut
Cap Nut
Front Side Trim
Front Side Trim
Vehicle front
Vehicle front
Clip A
Pin A
Passenger side scuff plate removal
(4)
(3)
1. Use shaded area to pull (1) and lift (2) Passenger side
Front Scuff Plate to detach Tab A and Clip A.
2. Use shaded area to pull (3) and lift (4) Passenger side
Front Scuff Plate to detach Tab B and Clip B.
Passenger side front trim removal
1. Peel back the Seaming Welt.
Hook B
Clip B
Pin B
Vehicle front
Front Side Trim
Front Side Trim
(Backside)
(Backside)
Clip
Clip
2. Remove Cap Nut.
Clip
Clip
Seaming Welt
Weather strip
3. Remove Front Side trim.
Hook A
Vehicle front
Hook A
(1)
(2)
Dampener
(3)
Hook B
Glove box removal
1. Push both sides (1) and pull (2) Glove box to dislodge 2
Hooks (A).
Hook A
2. Pull (3) Dampener to detach Hook B.
Caution
• If the glove box is closed without being joined to the stay
(1)
dampener, the stay dampener may be damaged. Verify
that the stay dampener is joined to the glove box before
closing the glove box.
6
Vehicle front
3. Remove Glove box by detaching 2 bottom Hooks.
Hook
Hook
Hook A
Pin B
(2)
(2)
Guide C
(3)
Hook A
4. Remove Glove box under cover in order of arrows (1) - (3).
(1)
Pin B
Vehicle front
Passenger side lower panel removal
1. Remove 2 Bolts.
Bolt tightening torque: 2.0 - 6.0 N•m (1.5 - 4.4 ft•lbf)
Vehicle front
Vehicle Front
Clips B
Clips B
(3)
(3)
Clips B
Clips B
Vehicle Front
Vehicle front
Air Bag deactivation (PAD) switch
Bolts
Bolts
Air Bag deactivation (PAD) switch
Clips B
Clips B
Guide E
Guide E
(4)
(4)
(2)
(2)
Pin D
Pin D
(1)
(1)
Clips B
Clips B
Clips B
Clips B
Hook C
Hook C
Pin D
Pin D
Guide E
Guide E
2. Disconnect the passenger airbag deactivation (PAD)
switch connector. (Only for vehicles with passenger airbag
deactivation (PAD) switch)
3. Remove lower panel in order of arrows (1) - (4).
7
Loading...