Whirlpool XHP1550WL, XHP1550WR, XHP1550WG, XHP1550VW, XHP1550VJ Installation Instructions

...

0 (0)

15.5" PEDESTAL INSTALLATION INSTRUCTIONS

For use only with front load washers and dryers

INSTRUCTIONS D’INSTALLATION DU PIÉDESTAL DE 15,5"

Pour utilisation avec les produits suivants seulement

laveuses et sécheuses à chargement par l’avant

Para una versión de estas instrucciones en español, visite www.whirlpool.com

Table of Contents

PEDESTAL SAFETY .....................................................1

INSTALLATION REQUIREMENTS ..............................2

Location Requirements .........................................2

Tools and Parts ......................................................2

INSTALLATION INSTRUCTIONS .................................3

Before Installing Pedestal .....................................3

INSTALLING THE PEDESTAL ...............................................5

COMPLETE THE INSTALLATION ..........................................6

WARRANTY ............................................................................8

INSTALLATION NOTES

Date of purchase: _________________________________ Date of installation: _______________________________ Installer: ________________________________________ Model number: ___________________________________ Serial number: ___________________________________

PEDESTAL SAFETY

SÉCURITÉ DU PIÉDESTAL .........................................9

EXIGENCES D’INSTALLATION ...................................9

Exigences d’emplacement ....................................9

Outillage et pièces .................................................9

INSTRUCTIONS D’INSTALLATION ...........................10

Avant l’installation du piédestal ..........................10

INSTALLATION DU PIÉDESTAL ................................12 ACHEVER L’INSTALLATION

GARANTIE ..................................................................16

NOTES CONCERNANT L’INSTALLATION

Date d’achat : _____________________________________ Date d’installation : ________________________________ Installateur : ______________________________________ Numéro de modèle : ________________________________ Numéro de série : __________________________________

Table des matières

.....................................14

W10178071B W10348601B - SP

INSTALLATION REQUIREMENTS

LOCATION REQUIREMENTS

Additional Items Needed:

Towel Sponge

Parts Supplied:

NOTE: If the washer/dryer and pedestal assembly are located in

a garage, 3" (76 mm) must be added under the pedestal so that the washer/dryer is 18" (458 mm) above the garage oor.

TOOLS AND PARTS

Gather the required tools and parts before starting installation.

Tools Needed:

Utility knife 1/4" hex-head ratchet or open-end wrench

Four #12 x 5/8" hex-head Drawer divider sheet metal screws

Level 9/16" open-end wrench

Pliers or slip-joint pliers Bucket

1/4" nut driver or nut driver

5/16" hex-head ratchet

INSTALLATION INSTRUCTIONS

BEFORE INSTALLING PEDESTAL

IMPORTANT: If your washer and dryer are already installed, they

must be uninstalled.

Uninstalling your washer

To avoid possible damage to the washer, the transport bolts on the back of the washer must be in place before installing the pedestal. For more information on transport bolts, see “Remove Transport System” in washer Use and Care Guide.

NOTE: If the washer is to be transported, call your local service center. To avoid suspension and structural damage, your washer must be properly set up for relocation by a certied technician.

1. Turn off the hot and cold water faucets.

2. Unplug the power supply cord.

3. Slowly loosen the ll hoses at the faucets to relieve the water

pressure. Use a sponge or towel to absorb the released water.

4. Remove the “HOT” and “COLD” ll hoses from the back of

the washer. Drain the water from the hoses into a bucket.

5. Remove the drain hose from the standpipe or laundry tub and

drain any water remaining in the hose into a bucket.

6. Pull the washer away from the wall so it can be tipped on its

back.

7. To avoid oor damage and ease of installation and handling,

unfold the empty pedestal box at and place it next to the washer. Lay the washer on its back (make sure that the power supply cord is not under the washer) so that the cardboard is under the entire lower back edge of the washer.

8. An additional small amount of water will drain out of the

washer when it is tipped back. See “Installing the Pedestal”.

Uninstalling your electric dryer

1. Unplug the power supply cord or disconnect wiring if dryer is

direct wired.

2. Pull the dryer away from the wall enough to loosen the vent

clamp. Loosen the clamp and gently remove the exhaust vent from the dryer exhaust outlet.

3. Pull the dryer away from the wall so that it can be tipped on

its back.

4. To avoid oor damage and ease installation and handling,

unfold the empty pedestal box at and place it next to the dryer. Lay the dryer on its back (make sure that the power supply cord is not under the dryer) so that the cardboard is under the entire lower back edge of the dryer. See “Installing the Pedestal”.

Uninstalling your gas dryer

1. Unplug the power supply cord or disconnect power.

2. Turn off the gas supply.

3. Pull the dryer away from the wall enough to loosen the vent

clamp. Loosen the clamp and gently remove the exhaust vent from the dryer exhaust outlet.

4. Disconnect the exible gas supply line from the dryer. Put a

piece of tape over the open ends of the gas line connection ttings.

5. Pull the dryer away from the wall so that it can be tipped on

its back.

6. To avoid oor damage and ease installation and handling,

Installation of new washer/dryer

If your washer/dryer is still in the packaging:

Washer/Dryer still in packaging

Conrm transport bolts are in place

NOTE: Transport bolts are only in washers.

Washer

Cut packaging as follows:

Washer: Cut plastic lm along dotted cut line around the base. Do not remove the packaging. Locate the transport bolts on rear of washer. Transport bolts must remain in washer while pedestal is installed. When laying the washer on its back, hold the bottom cap down on the oor. Do not remove the plastic lm, corner posts, or top cap.

Dryer: Cut carton around top and down corners along dotted cut lines. Lay all four carton sides on oor. Discard carton top and corner posts.

Dryer

Spacer pads

Hex-head screw

Drawer slide

INSTALLING THE PEDESTAL

Follow these instructions to install the pedestal on a washer or dryer.

1. Empty pedestal drawer

3. Remove pedestal drawer

Using a 1/4" nut driver, remove the hex-head screws from both drawer slides and save screws. Remove the drawer from the slides and set aside. Push the slides back into the pedestal.

4. Prepare the washer/dryer

Open the pedestal drawer as far as possible and remove the contents. The package contains four #12 x 5/8" hex-head sheet metal screws and a drawer divider.

2. Locate spacer pads

The four spacer pads are installed on the top of the pedestal. These pads reduce vibration between the pedestal and the washer/dryer.

Washer Bottom

Partially install two of the #12 x 5/8" hex-head sheet metal screws in the lower holes. Leave a space of about 3/8" (10 mm) between the screw head and the bottom of the washer/dryer.

NOTE: If your washer/dryer has feet installed, remove them.

Dryer Bottom

+ 11 hidden pages