Maytag SAV5910EWW, SAV5910AWW, SAV571EEWW, SAV5710AWW, SAV5701AWW Installation Instructions

...
0 (0)

®

Installation

Instructions

Top Loading Washer

Keep instructions for future reference.

Be sure manual stays with washer.

Instructions d’installation. . . . . . . . . . . . . . . . . . . . . . . . Page 7

Instructions de Instalación . . . . . . . . . . . . . . . . . . . . . Page 13

You'll Need a Few Things Before You Begin:

Tools

Screwdriver

Pliers

Wrench

Level

Parts Supplied

2 water fill

HOT

 

hoses

COLD

 

2 screened

 

hose filters

 

2 flat

rubber washers

4 rubber leveling foot pads

beaded tie-down strap

Maytag SAV5910EWW, SAV5910AWW, SAV571EEWW, SAV5710AWW, SAV5701AWW Installation Instructions

CONNECT WATER 2FILL HOSES TO

WASHER

Tightly push one flat rubber washer into one end of each water fill hose and attach this end of hose to washer. HOT and COLD connections are identified by letters H and C stamped into washer cabinet and by HOT and COLD printed on water fill hoses.

In most cases, hoses should cross when attached to correct water temperature faucet.

Tighten hose connections by hand until snug, then another 1/4 turn with pliers. DO NOT cross-thread or over-tighten couplings.

H C

HOT

COLD

Push rubber washer

into end of fill hose.

POSITION 5AND LEVEL

WASHER

Position washer in final location on clean, dry, firm, and level floor.

NOTE: To avoid damage to legs and base, do not slide washer across floor if leveling legs have been extended.

Loosen 7/8" locknuts and extend front leveling legs. Place rubber foot pads on all four leveling legs. Adjust front 2 leveling legs until machine is level side-to-side. Be sure machine does not rock. Tighten locknuts up to washer base, or washer will move out of position during operation.

Once front legs are adjusted, gently tilt washer forward on front legs and lower into place to correctly set rear self-leveling legs.

Check that washer is level front-to- back and side-to-side. WASHER

MUST NOT ROCK.

1. Level Front Legs

 

Lock

 

nut

 

Rubber

Leveling

foot pad

 

foot

 

2. Level rear legs

CONNECT

6POWER CORD TO ELECTRICITY

See Installation Requirements section. Plug washer into 3-prong grounded outlet only.

CLEAN TUB AND 7RUN THROUGH

ONE WASH CYCLE WITHOUT CLOTHES

Wipe tub with clean rag and soap diluted in warm water to remove any oil used in manufacturing. Use household spray cleaner if necessary.

Add water and detergent to washtub, and run before first use.

Questions?

See the User’s

Guide or call

Maytag Appliances

Sales Company

1-800-688-9900 USA

1-800-688-2002 Canada

1-800-688-2080 TTY USA Only

Installation Summary

Connect

water

 

fill

 

hoses

 

to

 

faucets

<![if ! IE]>

<![endif]>HOT

Set to 120° F

HOT

COLD

<![if ! IE]>

<![endif]>COLD

Connect water

fill hoses to washer

 

Run through a

 

cycle before

<![if ! IE]>

<![endif]>HOT

washing clothes

<![if ! IE]>

<![endif]>COLD

Connect power cord to electricity

Secure drain hose

Position washer. Level front

and rear legs.

Remove and store shipping plug and brace

Important Safety Information

About Ground Wires

In the event of an electrical short circuit, a ground wire reduces the risk of electric shock by providing an escape wire for the electric current.

Standard accepted color coding for ground wires is green or green with a yellow stripe.

Grounding wires and wires colored like grounding wires are NOT to be used as current carrying conductors.

Save These

Instructions

Grounding Instructions

For safety, washer must be grounded. All washer power supply cords are equipped with 3-prong grounding plug. Plug on cord must be plugged into appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify plug on washer cord. If plug will not fit outlet, have qualified electrician install proper outlet.

WARNING

To avoid risk of personal injury or death due to electrical shock:

Observe all local codes and ordinances.

Disconnect electrical power to unit before servicing.

Ground appliance properly.

Check with a qualified electrician if you are not sure this appliance is properly grounded.

DO NOT ground to gas line.

DO NOT ground to cold water pipe if pipe is interrupted by plastic, non-metallic gaskets, or other insulating (non-conducting) materials.

DO NOT modify plug on power cord. If plug does not fit electrical outlet, have proper outlet installed by qualified electrician.

DO NOT have a fuse in the neutral or ground circuit. A fuse in the neutral or ground circuit could result in an electrical shock.

DO NOT use an extension cord with this appliance.

DO NOT use an adapter plug with this appliance.

DO NOT pinch power cord.

Washer Dimensions

53.5" (137,1 cm)

<![if ! IE]>

<![endif]>(9336.6"cm)

<![if ! IE]>

<![endif]>cm)

<![if ! IE]>

<![endif]>43.6"(110,7

 

H C

26.9" (68,3 cm)

28" (71,1 cm)

2" (5,1 cm)

Optional Kits

Kits are available at extra cost

through your Maytag dealer or

Maytag Customer Assistance at

1-800-688-9900 USA

1-800-688-2002 Canada

1-800-688-2080 TTY USA Only

Siphon Break Kit

For standpipe installation below 36" (91.44 cm), install part #562P3.

Longer Water Inlet Hoses

8’ (2.44 m) inlet hose, part #20617.

10’ (3.05 m) inlet hose, part #20618.

Drain Hose Extension

Order this kit in two parts: the coupler, part #406P3, and 1’ additional drain hose, part #20616.

Anchor Kit

To stop washer from moving on uneven surfaces, install part #155P3.

Adjustable leg Extension Kit

To level washer on extremely uneven surfaces, install part #566P3.

5

Installation Requirements

Before You Install…

Consider

Description

 

 

Location

Use dimensions shown in manual to determine space needed for easy installation

 

and servicing.

 

Install washer on a solid floor. Never install washer on a platform or weak support

 

structure.

 

Wood floor constructions may sometimes need to be reinforced to minimize vibration

 

from unbalanced loads.

 

DO NOT install washer on carpeted floor. Carpet and soft tile surfaces also con-

 

tribute to vibration and/or tendency for washer to move slightly during spin cycle.

 

 

Electrical Requirements

Washer requires 120 volt, 15 amp, 60 Hz power supply and 3-prong grounding

 

plug. Power cord is approximately 69" long. Refer to serial plate for specific require-

 

ments. Wiring diagram is located in control hood.

 

 

Water Supply Faucets

Water supply faucets must fit standard 3/4" (19.05 mm) female garden hose cou-

 

plings. Do not use slip-on or clamp-on connections.

 

NOTE: Water supply faucets should be easily accessible and turned off before

 

extended periods of non-use.

 

 

Water Pressure

Static pressure measured at faucet must be 20–120 pounds per square inch (138 to

 

827 kPa). Water pressure under 20 pounds per square inch (138kPa) results in

 

extended washer fill time.

 

 

Drain

Drain receptacle must be able to handle hose with at least 1-1/4" (32 cm) outside

 

diameter. End of drain hose must be 36" (91.44 cm) above floor, or water may run

 

out of washer before end of cycle.

 

 

6

Loading...
+ 14 hidden pages